PT8A3232WEX

PT8A3230/1/2/3/4/5/6/7 |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Heating Controller Features Description  Dual Voltage (120V/240V) operations The PT8A3230/1/2/3/14/5/6/7 is a mixed signal  Auto temperature control with NTC CMOS LSI chip designed for the automatic controller of  NTC open protection heat with external NTC (Negative Temperature  Multi mode LED indicator Component). NTC open protection is implemented for  Direct drive SCR device safety. When NTC is open, it will cut off GATE  Auto Heating off after heating timer timeout output to disable heating, and the LED1 will flash at 1/8  Low cost 8-Pin DIP and SOIC package CLK. The device can be used in both 120V and 240V Applications power line supplier, automatically adjusting the heating  Hair Curler power according to the power line voltage to avoid heating appliance damage. Pin Configuration IC01-P10/1/2/3 IC01-14/5/6/7 N TC1 1 8 V DD N TC1 1 8 V DD N TC2 2 7 O FF N TC2 2 7 LED C LK 3 6 G ATE C LK 3 6 G ATE G ND 4 5 ON G ND 4 5 O N/O FF PT8A3230/1/2/3 PT8A3234/5/6/7 Pin Description Pin Name No. I/O Description PT8A323 0/1/2/3 PT8A323 4/5/6/7 PT8A323 0/1/2/3 PT8A323 4/5/6/7 1 NTC1 NTC1 I I NTC voltage input, NTC open detection input. 2 NTC2 NTC2 O O Output signal for NTC open detection. 3 CLK CLK I I Clock input from power line. 4 GND GND GND GND 5 ON ON/OFF I/O I/O 6 GATE GATE O O 7 OFF LED I/O O 8 VDD VDD Power Power 12-07-0006 Ground. Heating-on button input for PT8A3230/1/2/3 or Heatingon/off input for PT8A3234/5/6/7 and LED driving output. SCR trigger output, active high. Heating-off button input and LED2 driving output for PT8A3230/1/2/3 or only LED2 driving output for PT8A3234/5/6/7. Power. PT0211-6 1 07/06/2012 PT8A3230/1/2/3/4/5/6/7 Heating Controller |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Maximum Ratings Storage Temperature…………………………………………..- 65oC to +150oC Ambient Temperature with Power Applied……………………-20 oC to +85 oC Supply Voltage to Ground Potential (Inputs & VCC only)……….- 0.5 to +6.0V Supply Voltage to Ground Potential (Outputs & D/O only) …… - 0.5 to +6.0V DC Input Voltage …………………………………………- 0.5V to VCC +0.5V DC Output Current ……………………………………………………… 20mA Power Dissipation……………………………………………………… 500mW Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended Operation Conditions Sym Pin Description Min Typ Max Unit 3.5 5.0 5.5 V VCC VDD Supply voltage. fCLK CLK Input clock frequency - 50/60 - Hz TA - Operation temperature -20 - 85 C Min Typ Max Unit VIN = VCC - - 5 A PIN: NTC2 VIN = VCC Output high impedance - - 100 nA PIN: NTC1, CLK VIN = GND - - -5 A - - -100 nA -1.5 - - mA 2.0 - - mA 2.5 - - mA DC Electrical Characteristics (Unless otherwise noted, VCC = 3.5 ~ 5V, TA = -20 ~ 85ºC) Sym Description Test conditions IIH Input high current IIL Input low current IOH Output high current IOL Output low current VNTC0 Input voltage 0 PIN: NTC1 0.29VCC 0.31VCC 0.33VCC VNTC1 Input voltage 1 PIN: NTC1 0.37VCC 0.385VCC 0.40VCC VNTC2 Input voltage 2 PIN: NTC1 0.39VCC 0.40VCC 0.41VCC ICC Current consumption NTC1, CLK tied to GND, V CC = 5.0V - - 250 A Min Typ Max Unit - 50/60 - Hz 1.15 1.2 1.25 Hour PIN: NTC1, CLK PIN: NTC2 PIN: GATE PIN: NTC2 PIN: GATE VIN = 0 Output high impedance VCC = 5.0V Vout = 4.5V VCC = 5.0V Vout =0.5V V AC Electrical Characteristics (Unless otherwise noted, VCC = 3.5 ~ 5V, TA = -20 ~ 85ºC) Sym Description Test conditions fCLK CLK frequency Timer Power off timer FCLK= 50Hz 12-07-0006 PT0211-6 2 07/06/2012 PT8A3230/1/2/3/4/5/6/7 Heating Controller |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Block Diagram 2bit ADC NTC1 OFF (LED) Controller GATE NTC2 CLK ON (ON/OFF) Function Description State description Reset: The device will be at reset state after power-on. Heating-on: The device will be at heating-on state after heating-on button is pressed. Heating-off: This device enters heating-off state after its power-on reset or heating timer timeout or heating-off button pressed. Timer Once the device enters Heating-on state, internal timer start counting. It reaches timeout state and exit heating-on state after 216000 clock period, that is, the heating time is about 1 hour for 60Hz CLK signal, and 1.2 hour for 50Hz. Control signal output When working in Heating-on state, GATE/LED output will be related to NTC input and CLK input amplitude. Effect of NTC and CLK input voltage on GATE and LED indication GATE NTC NTC Working Power line （Trigger of (NTC open (normal temp state voltage detection) detection) SCR） 25% 0 ~ VNTC0 240V ON NTC20M(O X hm) *Note：1）X means any input. 2）Flash1 frequency if 1/32 CLK. 3）Flash2 frequency is 1/8 CLK. 4）LED2(Pin 7)is always in reverse with LED1. X X 12-07-0006 LED （Pin 5） PT8A3230/2/4/6 PT8A3231/3/ 5/7 VNTC up VNTC down On Flash1* Flash1 On Off Flash1 On On Flash1 Flash1 On On Off On Off Flash2* Off Off 12.5% Flash1 0 100% On Flash1 50% Flash1 0 0 0 PT0211-6 3 On On On On 07/06/2012 PT8A3230/1/2/3/4/5/6/7 Heating Controller |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Typical Application Circuit PT8A3230/1/2/3 application circuit PT8A3234/5/6/7application circuit 12-07-0006 PT0211-6 4 07/06/2012 PT8A3230/1/2/3/4/5/6/7 Heating Controller |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Mechanical Information PE (DIP-8) Symbol A A1 A2 B B1 c D E E1 e L E2 Note: 1) Controlling dimensions in millimeters. 2) Ref : JEDEC MS-001D/BA 12-07-0006 Dimensions In Millimeters Min Max 3.710 4.310 0.510 3.200 3.600 0.380 0.570 1.524 BSC 0.204 0.360 9.000 9.400 6.200 6.600 7.320 7.920 2.540 BSC 3.000 3.600 8.400 9.000 PT0211-6 5 07/06/2012 PT8A3230/1/2/3/4/5/6/7 Heating Controller |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| WE (SOIC-8) Symbol A A1 A2 b c D E E1 e L θ Note: 1) Controlling dimensions in millimeters. 2) Ref : JEDEC MS-012E/AA 12-07-0006 Dimensions In Millimeters Min Max 1.350 1.750 0.100 0.250 1.350 1.550 0.330 0.510 0.170 0.250 4.700 5.100 3.800 4.000 5.800 6.200 1.27 BSC 0.400 1.270 0° 8° PT0211-6 6 07/06/2012 PT8A3230/1/2/3/4/5/6/7 Heating Controller |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Ordering Information Part No. PT8A323xPE PT8A323xWE Package Code P W Package Lead free DIP-8 Lead free and Green SOIC-8 Note:  x=0/1/2/3/4/5/6/7 show different part no with different function, details see below table.  E = Pb-free or Pb-free & Green  Adding X Suffix= Tape/Reel Part No Option Part No. LED@ Heating on PT8A3230 PT8A3231 Flash Constant Timer of Auto power off (1h@60Hz) Y Y PT8A3232 PT8A3233 Flash Constant N N Two Keys Two Keys PT8A3234 PT8A3235 Flash Constant Y Y Single Key Single Key PT8A3236 Flash N Single Key PT8A3237 Constant N Single Key Control Keys Two Keys Two Keys Pericom Semiconductor Corporation  1-800-435-2336  www.pericom.com Pericom Technology Incorporation reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. Pericom Technology does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom Technology product. The company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom. 12-07-0006 PT0211-6 7 07/06/2012