RS2MA-13

SPICE MODELS: RS2A RS2B RS2D RS2G RS2J RS2K RS2M RS2AA RS2BA RS2DA RS2GA RS2JA RS2KA RS2MA RS2A/A - RS2M/A 1.5A SURFACE MOUNT FAST RECOVERY RECTIFIER Features · · · · · · Glass Passivated Die Construction Fast Recovery Time For High Efficiency Low Forward Voltage Drop and High Current Capability Surge Overload Rating to 50A Peak Ideally Suited for Automated Assembly Plastic Material: UL Flammability Classification Rating 94V-0 SMA B A · · · · · · · Min Max Min Max A 2.29 2.92 3.30 3.94 B 4.00 4.60 4.06 4.57 C 1.27 1.63 1.96 2.21 D 0.15 0.31 0.15 0.31 C D Mechanical Data J Case: Molded Plastic Terminals: Solder Plated Terminal Solderable per MIL-STD-202, Method 208 Polarity: Cathode Band or Cathode Notch SMA Weight: 0.065 grams (approx.) SMB Weight: 0.09 grams (approx.) Mounting Position: Any Marking: Type Number E 4.80 5.59 5.00 5.59 G 0.10 0.20 0.10 0.20 H 0.76 1.52 0.76 1.52 2.01 2.62 2.00 2.62 J G E H SMB Dim All Dimensions in mm AA, BA, DA, GA, JA, KA, MA Suffix Designates SMA Package A, B, D, G, J, K Suffix Designates SMB Package Maximum Ratings and Electrical Characteristics TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Symbol RS2 A/AA RS2 B/BA RS2 D/DA RS2 G/GA RS2 J/JA RS2 K/KA RS2 M/MA Unit VRRM VRWM VR 50 100 200 400 600 800 1000 V VR(RMS) 35 70 140 280 420 560 700 V IO 1.5 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load (JEDEC Method) IFSM 50 A Forward Voltage VFM 1.3 V IRM 5.0 200 mA Average Rectified Output Current Peak Reverse Current at Rated DC Blocking Voltage @ TT = 120°C @ IF = 1.5A @ TA = 25°C @ TA = 125°C Reverse Recovery Time (Note 3) trr Typical Junction Capacitance (Note 2) Cj 30 pF RqJT 20 K/W Tj, TSTG -65 to +150 °C Typical Thermal Resistance, Junction to Terminal (Note 1) Operating and Storage Temperature Range Notes: 150 250 500 ns 1. Thermal Resistance: Junction to terminal, unit mounted on PC board with 5.0 mm2 (0.013 mm thick) copper pads as heat sink. 2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. 3. Reverse Recovery Test Conditions: IF = 0.5A, IR = 1.0A, Irr = 0.25A. See Figure 5. DS15004 Rev. E-2 1 of 2 www.diodes.com RS2A/A - RS2M/A ã Diodes Incorporated IF, INSTANTANEOUS FORWARD CURRENT (A) IO, AVERAGE RECTIFIED CURRENT (A) 1.5 1.0 0.5 0 25 50 75 100 125 150 10 1.0 0.1 Tj = 25°C 0.01 175 0 IR, INSTANTANEOUS REVERSE CURRENT (µA) IFSM, PEAK FORWARD SURGE CURRENT (A) Single Half-Sine-Wave (JEDEC Method) 50 Tj = 150°C 40 30 20 10 0 10 0.8 1.2 1.6 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics TT, TERMINAL TEMPERATURE (°C) Fig. 1 Forward Current Derating Curve 1 0.4 1000 Tj = 125°C 100 10 0.1 100 NUMBER OF CYCLES AT 60 Hz Fig. 3 Forward Surge Current Derating Curve Tj = 25°C 1.0 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 4, Typical Reverse Characteristics trr +0.5A Device Under Test (-) 0A (+) Pulse Generator (Note 2) 50V DC Approx (-) Oscilloscope (Note 1) -0.25A (+) -1.0A Set time base for 50/100 ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit DS15004 Rev. E-2 2 of 2 www.diodes.com RS2A/A - RS2M/A