SLIN-03E2AL

NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. RoHS Compliant • • • • SLIN-03E2Ax Features • • • • • • • • • • • Rev.D Wide Input Voltage Range Fixed Switching Frequency Power Good Signal Remote Sense Ability to Sink and Source Current Cost Efficient Open Frame Design Over Temperature Protection Output Over Current Protection Remote On/Off Tunable LoopTM (a registered trademark of Lineage Power Systems) to Optimize Dynamic output voltage response Class 1, Category 2, Non-Isolated DC/DC Converter (refer to IPC-9592) Compliant to RoHS EU Directive 2002/95/EC Compatible in a Pb-free or SnPb reflow environment UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified VDE‡ 0805:2001-12 (EN60950-1) Licensed Applications • • • Distributed power architectures Intermediate bus voltage applications Telecommunications equipment • • • Servers and storage applications Networking equipment Industrial equipment Description The SLIN-03E2Ax power modules are non-isolated dc-dc converters that can deliver up to 3A of output current. These modules operate over a wide range of input voltage (VIN = 4.5Vdc-14Vdc) and provide a precisely regulated output voltage from 0.59Vdc to 5.5Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, and over current and over temperature protection. A new feature, the Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. Part Selection Output Voltage 0.59 Vdc - 5.5 Vdc Input Voltage 4.5 Vdc - 14 Vdc Max. Output Current 3A Typical Efficiency 91% Model Number Active High SLIN-03E2A0 Model Number Active Low SLIN-03E2AL Notes: Add “G” suffix at the end of the model number to indicate Tray Packaging. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 1 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs Part Number Explanation S LIN – 03 E 2A 0 12 3456 1---Surface mount 2---Series code 3---Output current (3A) October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. 4--- Wide input voltage range (4.5-14V) 5--- Wide output voltage range (0.59-5.5V) 6--- Enable, active high, change “0” to “L” means active low Absolute Maximum Ratings Parameter Continuous Input Voltage Operating Ambient Temperature Storage Temperature Min -0.3 -40 -55 Typ Max 15 85 125 Unit V °C °C Notes Note: Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Input Specifications Parameter Operating Input Voltage Input Current (full load) Input Current (no load) Vo=0.6V Vo=3.3V Input Stand-by Current Input Reflected Ripple Current (pk-pk) I2t Inrush Current Transient Input Ripple Rejection (120Hz) Turn-on Threshold Turn-off Threshold Hysteresis 3.6 0.4 17 55 1 43 50 1 4.0 mA mA mA mA A2s dB V V V VIN=12V, module enabled VIN = 12.0Vdc, module disabled 5Hz to 20MHz, 1μH source impedance; VIN =0 to 14V, IO= IOmax ; See Test Configurations Min 4.5 Typ Max 14 3.5 Unit V A VIN=4.5V to 14V Notes CAUTION: This converter is not internally fused. An input line fuse must be used in application. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 5A. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 2 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs Output Specifications Parameter Output Voltage Set Point Output Voltage Adjustment Range1 Remote Sense Range Load Regulation VO ≥ 2.5V VO < 2.5V Line Regulation VO ≥ 2.5V VO < 2.5V Temperature Regulation (-40°C to +85°C) Ripple and Noise (pk-pk) Ripple and Noise (rms) Output Current Range Output DC Current Limit Output Short-Circuit Current Output Capacitance2 ESR≥ 1 mΩ ESR≥0.15 mΩ ESR≥ 10 mΩ 0 0 0 0 Turn-On Delay Time 2 50 20 2 Min -1.5 -3.0 0.59 Typ - October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Max +1.5 +3.0 5.5 0.5 10 5 0.4 10 0.4 110 40 3 200 6.7 47 1000 3000 Unit %Vo,set %Vo,set V V mV mV %Vo,set mV %Vo,set mV mV A %Io,max mA uF uF uF mS 5Hz to 20MHz BW, VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1μF // 10 μF ceramic capacitors) in either sink or source mode Hiccup Mode Vo≤250mV, Hiccup Mode Without the Tunable LoopTM TM With the Tunable Loop With the Tunable LoopTM Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo =10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo =10% of Vo, set) time for Vo to rise from 10% of Vo, set to 90% of Vo, set Vin=Vin, min to Vin, max, Io=Io, min to Io, max, With or without maximum external capacitance IO=IO, min to IO, max Notes with 0.5% tolerance for external resistor used to set output voltage Over all operating input voltage, resistive load, and temperature conditions until end of life selected by an external resistor VIN=VIN, min to VIN, max - mS Output voltage Rise time Output voltage overshoot Dynamic Load Response △V50%~100% - 4 - 3 mS %Vo,set Peak Deviation Settling Time Peak Deviation Settling Time - 220 60 240 60 - mV uS mV uS di/dt=10A/us, Vin=Vin,nom, Vo=1.8V, Ta=25°C, Co=0 of Max Load △V100%~50% of Max Load Notes: 1. Some output voltages may not be possible depending on the input voltage. 2. External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best transient response (See the Tunable LoopTM section for details). 3. Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 3 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Min Vo=0.59V Vo=1.2V Vo=1.8V Vo=2.5V Vo=3.3V Vo=5.0V 90 Typ 73.3 82.9 86.5 88.9 90.6 92.6 600 140 7 1.55 25,017,068 Max 100 100 110 50 Unit % % % % % % kHz °C mV mV %Vo,set Ω g hours Calculated Per Bell Core SR-332 (Io=0.8Io, max, Ta=40°C, Telecordia Issue 2 Method 1 Case 3) Vin, min to Vin, max; Io, min to Io, max Signal Interface Open Drain, Vsupply ≤ 5Vdc Notes General Specifications Parameter Efficiency Vin= 12Vdc, Ta=25°C Io=Io, max , Vo= Vo,set Switching Frequency Over Temperature Protection Tracking Accuracy Power-Up: 2V/ms Power-Down: 2V/ms PGOOD (Power Good) Output Voltage Limit for PGOOD Pulldown resistance of PGOOD pin Weight MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H) 0.48 x 0.48 x 0.246 12.19 x 12.19 x 6.25 - Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 4 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs Efficiency Data October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. 85 80 90 85 EFFICIENCY, η (%) 75 Vin=4.5V 70 65 60 55 0 0.5 1 1.5 2 2.5 3 Vin=12V Vin=14V EFFICIENCY, η (%) 80 Vin=4.5V Vin=14V 75 Vin=12V 70 65 0 0.5 1 1.5 2 2.5 3 OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=0.6V 95 95 Vo=1.2V 90 90 EFFICIENCY, η (%)) EFFICIENCY, η (%) 85 Vin=4.5V 80 Vin=14V Vin=12V 85 Vin=4.5V Vin=14V Vin=12V 80 75 75 70 0 0.5 1 1.5 2 2.5 3 70 0 0.5 1 1.5 2 2.5 3 OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=1.8V 100 95 100 95 Vo=2.5V EFFICIENCY, η (%)) 90 85 80 75 70 0 0.5 1 1.5 2 2.5 3 Vin=4.5V Vin=14V Vin=12V EFFICIENCY, η (%) 90 85 Vin=8V 80 75 70 0 0.5 1 1.5 2 2.5 3 Vin=12V Vin=14V OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=3.3V Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 5 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs Thermal Derating Curves 4 October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. 4 OUTPUT CURRENT, Io (A) 3 OUTPUT CURRENT, Io (A) 3 NC NC 2 2 1 20 30 40 50 60 70 O 1 20 30 40 50 60 70 O 80 90 80 90 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=0.6V 4 Vo=1.2V 4 OUTPUT CURRENT, Io (A) 3 OUTPUT CURRENT, Io (A) 3 NC 0.5m/s (100LFM) NC 2 2 1 20 30 40 50 60 70 O 1 20 30 40 50 60 70 O 80 90 80 90 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=1.8V 4 Vo=2.5V 4 3 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) 3 0.5m/s (100LFM) 0.5m/s (100LFM) 2 NC 2 NC 1 20 30 40 50 60 70 O 1 20 30 40 50 60 70 O 80 90 80 90 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=3.3V Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 6 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs Ripple and Noise Waveforms October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1μs/div) Vin=12V, Vo=0.6V, Io = Io,max Vin=12V, Vo=1.2V, Io = Io,max OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1μs/div) Vin=12V, Vo=1.8V, Io = Io,max Vin=12V, Vo=2.5V, Io = Io,max OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vin=12V, Vo=3.3V, Io = Io,max Vin=12V, Vo=5.0V, Io = Io,max . Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 7 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Transient Response Waveforms OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT, IO (A) (1Adiv) TIME, t (20μs /div) OUTPUT CURRENT, IO (A) (1Adiv) OUTPUT VOLTAGE VO (V) (100mV/div) TIME, t (20μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=0.6V OUTPUT VOLTAGE VO (V) (100mV/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=1.2V OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT, IO (A) (1Adiv) TIME, t (20μs /div) OUTPUT CURRENT, IO (A) (1Adiv) TIME, t (20μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=1.8V OUTPUT VOLTAGE VO (V) (200mV/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=2.5V OUTPUT VOLTAGE VO (V) (200mV/div) OUTPUT CURRENT, IO (A) (1Adiv) TIME, t (20μs /div) OUTPUT CURRENT, IO (A) (1Adiv) TIME, t (20μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=3.3V Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 8 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Startup Time ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (200mV/div) VON/OFF (V) (5V/div) TIME, t (2 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VON/OFF (V) (2V/div) TIME, t (2 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=0.6V Start-up Using On/Off Voltage (Io = Io,max), Vo=1.2V ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (10V/div) VO (V) (500mV/div) TIME, t (2 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (5V/div) TIME, t (2 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=1.8V Start-up Using On/Off Voltage (Io = Io,max), Vo=2.5V TIME, t (2 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (2V/div) VON/OFF (V) (2V/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (5V/div) TIME, t (2 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=3.3V Start-up Using On/Off Voltage (Io = Io,max), Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 9 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Startup Time (continued) OUTPUT VOLTAGE VO (V) (200mV/div) TIME, t (2 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VIN (V) (5V/div) INPUT VOLTAGE VIN (V) (5V/div) TIME, t (2 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=0.6V OUTPUT VOLTAGE VO (V) (500mV/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=1.2V TIME, t (2 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (5V/div) INPUT VOLTAGE VIN (V) (5V/div) TIME, t (2 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=1.8V Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=2.5V TIME, t (2 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (2V/div) VIN (V) (5V/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (5V/div) TIME, t (2 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=3.3V Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 10 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs October 8, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. CURRENT PROBE Test Configurations Input Reflected Ripple Current Test Setup. TO OSCILLOSCOPE LTEST 1μH VIN(+) BATTERY CS 1000μF Electrolytic E.S.R.