BQ24210EVM-678

User's Guide SLUU477B – December 2010 – Revised November 2015 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger This user's guide describes the features and operation of the bq24210/2 Evaluation Module (EVM). The EVM assists users in evaluating the bq24210/2 solar charger. The printed-circuit board for the EVM is labeled HPA678. The manual includes the bq24210/2EVM bill of materials, board layout, and schematic. 1 2 3 4 Contents Introduction ................................................................................................................... 2 1.1 EVM Features ....................................................................................................... 2 1.2 General Description ................................................................................................ 2 1.3 I/O Header Descriptions ........................................................................................... 2 1.4 Jumper Settings ..................................................................................................... 3 1.5 Recommended Operating Conditions ............................................................................ 3 Test Summary ................................................................................................................ 4 2.1 Definitions ............................................................................................................ 4 2.2 Recommended Equipment for Testing ........................................................................... 5 2.3 Recommended Test Equipment Setup .......................................................................... 5 2.4 Recommended Test Procedure to Confirm IC Operation ..................................................... 6 PCB Layout Guideline ....................................................................................................... 6 Bill of Materials, Board Layout, and Schematics ........................................................................ 7 4.1 Bill of Materials ...................................................................................................... 7 4.2 Board Layout ........................................................................................................ 8 4.3 Schematics ......................................................................................................... 11 List of Figures 1 Original Test Setup for HPA678 (bq24210/2EVM) ...................................................................... 5 2 Top Assembly ................................................................................................................ 8 3 Top Layer ..................................................................................................................... 9 4 Bottom Layer ................................................................................................................ 10 5 bq24210 EVM Schematic ................................................................................................. 11 List of Tables 1 2 3 4 .................................................................................................... Jumper Settings .............................................................................................................. Recommended Operating Conditions ..................................................................................... Bill of Materials ............................................................................................................... I/O Header Descriptions SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger Copyright © 2010–2015, Texas Instruments Incorporated 2 3 3 7 1 Introduction www.ti.com 1 Introduction 1.1 EVM Features • • • • • 1.2 800-mA, single-input, single-cell Li-ion battery solar charger Resistor-programmable setting for charge current and input voltage dynamic power management LED Indication for status Test points for key signals available for testing purposes – easy probe hook-up Jumpers available – easy to change setting General Description The bq24210/2 series of devices are highly integrated Li-ion linear chargers devices targeted at spacelimited portable applications. The high input voltage range with input overvoltage protection supports lowcost unregulated adapters. The input voltage regulation loop with programmable input voltage regulation threshold make it suitable for charging from alternative power sources, such as solar panel or inductive charging pad. The integrated circuit (IC) has a single power output that charges the battery. A system load can be placed in parallel with the battery as long as the average system load does not keep the battery from charging fully during the 10-hour safety timer. The bq24210 has an EN pin whereas the bq24212 has a MODE pin. See the data sheet for an explanation of the differences between the two pins. The battery is charged in three phases: conditioning, constant current' and constant voltage. In all charge phases, an internal control loop monitors the IC junction temperature and reduces the charge current if an internal temperature threshold is exceeded. For additional details, see the bq24210 (SLUSA76) or bq24212 (SLUSAL2) data sheet. 1.3 I/O Header Descriptions Table 1. I/O Header Descriptions 2 Jack Description J1–VBUS Positive input J1–GND Negative input J2–BAT Charger output J2–GND Ground J2–TS Temperature qualification input J3-GND Ground J3-VDPM Programs the input voltage regulation threshold J3-CHG Charge status indication J3-EN (BQ24210 only) Chip Enable control. This pin must be pulled low in order for the device to operate. J3-MODE (BQ24212 only) Chip MODE control. See data sheet for explanation of chip operation when MODE is high and low. J3-PG Power present indication J4-ISET Programs the fast-charge current setting J4-VTSB TS bias reference voltage pin, regulated output J4-GND Ground 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Introduction www.ti.com 1.4 Jumper Settings Table 2. Jumper Settings 1.5 Jack Description Factory Setting JP1 Programs the fast-charge current setting. 500 mA when JP1 ON; external setting when JP1 OFF Jumper OFF (external setting) JP2 Connect /EN and /PG together when JP2 ON to enable charger when power present Jumper OFF (external /EN) JP3 Programs the input voltage regulation threshold. 4.5V when JP3 ON; external setting when JP3 OFF. Jumper OFF (external setting) JP4 Limited power charge mode (LPCM) when JP4 ON; normal operation when JP4 OFF Jumper OFF (normal operation) JP5 Select external TS input or internal TS setting 1-2 : External TS input 2-3 : Internal TS setting Jumper ON 1-2 (external TS) JP6 The pullup power source supplies for the LEDs 1-2 : BAT 2-3 : VBUS Jumper ON 2-3 (VBUS) JP7 Charger EN / MODE 1-2 : OFF/HIGH 2-3 : ON/LOW Jumper ON 1-2 (charger OFF / MODE High) Recommended Operating Conditions Table 3. Recommended Operating Conditions Description Min Supply voltage, VBUS Input voltage Battery voltage, VBAT Voltage applied at VBAT terminal of J2 Supply current Charge current, Ichrg Max Unit 4.5 7.3 V 0 4.2 V Maximum input current 0 0.8 A Battery charge current 0 0.8 A 0 125 °C Operating junction temperature range, TJ Typ Notes An external resistor is used to program the VBUS_DPM. The programming resistor, RVDPM is dictated by the following equation: R VDPM = (VBUS_ DPM - VBUS_DPM_ 1 ) KVBUS_DPM (1) Where: VBUS_DPM is the desired input voltage regulation voltage threshold. VBUS_DPM_1 is the built-in offset threshold, nominally 3.5 V. KVBUS_DPM is a gain factor found in the electrical specification. If VDPM pin is shorted to VSS; the VBUS_DPM must be clamped to 3.65 V. If the VDPM pin is floated (open circuit), the IC operates in Battery Tracking mode. In this case, VBUS DPM threshold is internally set as VTRK, which is BAT + 100 mV. (BAT > 3.65 V) or 3.75 V (BAT ≤ 3.4 V). Connecting JP3 set 4.5 V VDPM on EVM. An external resistor is used to program the output current (50-800 mA). The equation for charge current is: K RISET = ISE T IO UT (2) Where, IOUT is the desired fast-charge current; KISET is a gain factor found in the specification. The termination and precharge current are internally set at 10% and 20% of fast-charge current, respectively. The precharge-to-fast-charge, Vlowv threshold is set to 2.5 V. Connecting JP1 set 500 mADC for fast-charge current and 100 mADC for precharge current on EVM. SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger Copyright © 2010–2015, Texas Instruments Incorporated 3 Test Summary 2 Test Summary 2.1 Definitions www.ti.com This procedure details how to configure the HPA678 evaluation board. On the test procedure, the following naming conventions are followed. VXXX : LOADW: V(TPyyy): V(Jxx): V(XXX): External voltage supply name (VBUS, VBAT) External load name (LOADR, LOADI) Voltage at internal test point (TPyyy). For example, V(TP1) means the voltage at TP1. Voltage at jack terminal (Jxx). Voltage at (XXX). For example, V(VDPM) means the voltage at the test point which is marked VDPM. V(XXX, YYY): Voltage across point XXX and YYY. I(JXX(YYY)): Current going out from the YYY terminal of jack XX. Jxx(BBB): Terminal or pin BBB of jack xx Jxx ON : Internal jumper Jxx terminals are shorted. Jxx OFF: Internal jumper Jxx terminals are open. Jxx (-YY-) ON: Internal jumper Jxx adjacent terminals marked as YY are shorted. Measure:→A,B Check specified parameters A, B. If measured values are not within specified limits, the unit under test has failed. Observe →A,B Observe if A, B occur. If they do not occur, the unit under test has failed. Assembly drawings have location for jumpers, test points, and individual components 4 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Test Summary www.ti.com 2.2 2.2.1 Recommended Equipment for Testing Power Supplies Power Supply #1 (PS#1): a power supply capable of supplying 20 V at 1 A 2.2.2 Loads A 20-V (or above), 1-A (or above) electronic load that can operate at constant current and constant voltage mode or equivalent 2.2.3 Meters Four Fluke 75 multimeters, (equivalent or better) or two equivalent voltage meters and two equivalent current meters. The current meters must be capable of measuring 1 A + current. 2.3 Recommended Test Equipment Setup 1. Set the power supply #1 (PS#1) for 6.5 V ± 200 mVDC, 1-A ± 0.1-A current limit, and then turn off supply. 2. Connect the output of PS#1 in series with a current meter (multimeter) to J1 (VBUS, GND). 3. Connect a voltage meter across J1 (VBUS, GND). 4. Connect Load #1 in series with a current meter to J2 (VBAT, GND). Turn off Load #1. 5. Connect a voltage meter across J2 (VBAT, GND). 6. Check all jumper shunts. JP1: OFF; JP2: OFF; JP3: OFF; JP4: OFF; JP5: connect 1-2 (External TS); JP6: connect 2-3 (VBUS); JP7: connect 1-2 (charger OFF/ MODE high). J1 Power supply #1 BQ24210 EVM HPA678 J2 I Iin BAT GND I V GND VBUS V IBAT Load #1 TS U1 APPLICATION CIRCUIT JP3 JP1 LED PG CHG D1 D2 J4 J3 JP4 JP5 JP7 JP6 JP2 Figure 1. Original Test Setup for HPA678 (bq24210/2EVM) SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger Copyright © 2010–2015, Texas Instruments Incorporated 5 Test Summary 2.4 2.4.1 www.ti.com Recommended Test Procedure to Confirm IC Operation Power Supply Make sure that EQUIPMENT SETUP steps are followed. Disconnect LOAD #1. Turn on PS#1. Measure → V(J1(VBUS)) = 6.5 V ± 200 mV Measure → V(J2(VBAT)) = 0 V ± 200 mV Measure → V(J4(VTSB)) = 0 V ± 200 mV Observe → D1 (PG) ON, D2 (CHG) OFF 2.4.2 Charger Enable and Battery Detection Connect JP1; Connect 2-3 of JP7 (Charger ON/MODE High) Measure → V(J4(VTSB)) = 2.2 V ± 300 mV Connect 2-3 of JP5 (Internal TS); Adjust R6 until V(JP4-1) = 0.7 V ± 200 mV Measure → V(J2(VBAT))=4.2 V ± 200 mV Observe → D1 (PG) ON, D2 (CHG) OFF 2.4.3 Charge Current/Voltage Regulation Reconnect LOAD#1. Turn on. Use the constant voltage mode. Connect JP1; Set the output voltage to be 2.2 V. Measure → I(J2(VBAT)) = 0.1 A ± 50 mA Observe → D1 (PG) ON, D2 (CHG) ON Increase the voltage of LOAD#1 to be 3.5 V. Measure → I(J2(VBAT)) = 0.5 A ± 100 mA Observe → D1 (PG) ON, D2 (CHG) ON 3 PCB Layout Guideline 1. It is critical that the exposed thermal pad on the backside of the bq24210 package be soldered to the PCB ground. Ensure that sufficient thermal vias are right underneath the IC, connecting to the ground plane on the other layers. 2. Make the interconnections of the decoupling capacitors for VBUS, BATC to the IC as short as possible. 3. Use the EVM layout for design reference. 6 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Bill of Materials, Board Layout, and Schematics www.ti.com 4 Bill of Materials, Board Layout, and Schematics 4.1 Bill of Materials Table 4. Bill of Materials Count RefDes Value Description Size Part Number 1 C1 10uF Capacitor, Ceramic, 25V,X7R, 10% 1206 STD 2 C2, C4 0.1uF Capacitor, Ceramic, 25V, X7R, 10% 0603 STD 1 1 C3 10uF Capacitor, Ceramic, 6.3V, X7R, 10% 0805 STD 0 0 C5, C6 Open Capacitor, Ceramic, 25V, X7R, 10% 0603 STD 2 2 D1, D2 LTST-C190CKT Diode, LED, Red, 1.8-V, 20-mA, 20-mcd 0603 LTST-C190CKT 1 1 D3 BZX84C5V1-7 Diode, Zener, 5.1V, 350-mW SOT-23 BZX84C5V1-7 1 1 J1 PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN 1 1 J2 ED555/3DS Terminal Block, 3-pin, 6-A, 3.5mm 0.41 x 0.25 inch ED555/3DS 1 1 J3 PEC05SAAN Header, Male 5-pin, 100mil spacing, 0.100 inch x 5 PEC05SAAN 1 1 J4 PEC03SAAN Header, Male 3-pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN 4 4 JP1, JP2, JP3, JP4 PEC02SAAN Header, 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN 3 3 JP5, JP6, JP7 PEC03SAAN Header, 3 pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN 1 1 R1 21.5k Resistor, Chip, 1/16W, 1% 0603 STD 2 2 R2, R4 1.50K Resistor, Chip, 1/16W, 1% 0603 STD 1 1 R3 750 Resistor, Chip, 1/16W, 1% 0603 STD 1 1 R5 6.65k Resistor, Chip, 1/16W, 1% 0603 Std 1 1 R6 100k Potentiometer, 1/4 Cermet, 12-Turn, Top-Adjust 0.25x0.17 inch 3266W-1-104LF 1 1 R7 4.75k Resistor, Chip, 1/16-W, 1% 0603 STD 0 0 TP1, TP2, TP3 Open Test Point, 0.020 Hole 1 0 U1 BQ24210DQC IC, 800mA, Single-Input, Single Cell Li-Ion Battery Solar Charger TDFN-10 BQ24210DQC 0 1 U1 BQ24212DQC IC, 800mA, Single-Input, Single Cell Li-Ion Battery Solar Charger TDFN-10 BQ24212DQC 7 7 — Shunt, 100-mil, Black 0.1 929950-00 1 1 — PCB, 2.64" x 2.1" x 0.062" 1 1 — Label -001 -002 1 2 STD HPA678 1.25 x 0.25 inch THT-13-457-10 Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed. 2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable. 3. These assemblies must comply with workmanship standards IPC-A-610 Class 2. 4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components. 5. Install label after final wash. Text shall be 8 pt font. Text shall be per Table 1. Table 1 Assembly Number Text HPA678-001 BQ24210EVM-678 HPA678-002 BQ24212EVM-678 SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger Copyright © 2010–2015, Texas Instruments Incorporated 7 Bill of Materials, Board Layout, and Schematics 4.2 www.ti.com Board Layout Figure 2. Top Assembly 8 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Bill of Materials, Board Layout, and Schematics www.ti.com Figure 3. Top Layer SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger Copyright © 2010–2015, Texas Instruments Incorporated 9 Bill of Materials, Board Layout, and Schematics www.ti.com Figure 4. Bottom Layer 10 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Bill of Materials, Board Layout, and Schematics www.ti.com 4.3 Schematics Figure 5. bq24210 EVM Schematic SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger Copyright © 2010–2015, Texas Instruments Incorporated 11 Revision History www.ti.com Revision History Changes from A Revision (August 2011) to B Revision ................................................................................................ Page • • • Changed the document title From: 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger With Power Path To: 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger ................................................................... 1 Changed Section 1.1 From: 800-mA, single-input, single-cell Li-ion battery solar charger with Power Path To: 800-mA, single-input, single-cell Li-ion battery solar charger .................................................................................. 2 Changed the Description of U1 in Table 4 From: IC, 800mA, Single-Input, Single Cell Li-Ion Battery Solar Charger with bidirectional Power Path To: IC, 800mA, Single-Input, Single Cell Li-Ion Battery Solar Charger ............................... 7 NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Revision History Changes from Original (December 2010) to A Revision ................................................................................................ Page • • • • • • Changed Section 2.2, removed subsections Safety, Quality, and Apparel ........................................................ 5 Changed Section 2.4 From: Procedure To: Recommended Test Procedure to Confirm IC Operation ........................ 6 Removed subsection VDPM ((Input Voltage Regulation) Setting) and Test Complete From: Section 2.4 .................... 6 Changed Table 4 .......................................................................................................................... 7 Changed Figure 2, Figure 3, and Figure 4 ............................................................................................. 8 Changed Figure 5........................................................................................................................ 11 NOTE: Page numbers for previous revisions may differ from page numbers in the current version. 12 Revision History SLUU477B – December 2010 – Revised November 2015 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES 1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein. Acceptance of the EVM is expressly subject to the following terms and conditions. 1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software 1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned, or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production system. 2 Limited Warranty and Related Remedies/Disclaimers: 2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License Agreement. 2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as mandated by government requirements. TI does not test all parameters of each EVM. 2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM, or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day warranty period. 3 Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter. 3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant: CAUTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Interference Statement for Class A EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3.2 Canada 3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 Concerning EVMs Including Radio Transmitters: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Concernant les EVMs avec appareils radio: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Concerning EVMs Including Detachable Antennas: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur 3.3 Japan 3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に 輸入される評価用キット、ボードについては、次のところをご覧ください。 http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified by TI as conforming to Technical Regulations of Radio Law of Japan. If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of Japan to follow the instructions below with respect to EVMs: 1. 2. 3. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan, Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan. SPACER SPACER SPACER SPACER SPACER 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 2. 3. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 実験局の免許を取得後ご使用いただく。 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page SPACER 4 EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information related to, for example, temperatures and voltages. 4.3 Safety-Related Warnings and Restrictions: 4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or property damage. If there are questions concerning performance ratings and specifications, User should contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit components may have elevated case temperatures. These components include but are not limited to linear regulators, switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the information in the associated documentation. When working with the EVM, please be aware that the EVM may become very warm. 4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems, and subsystems. User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees, affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or designees. 4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal, state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local requirements. 5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as accurate, complete, reliable, current, or error-free. SPACER SPACER SPACER SPACER SPACER SPACER SPACER 6. Disclaimers: 6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS. 6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF THE EVM. 7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES, EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED. 8. Limitations on Damages and Liability: 8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED. 8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT. 9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s) will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s), excluding any postage or packaging costs. 10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas, without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas. Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated spacer IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated