CD74HC4017PWT

[ /Title (CD74 HC401 7) /Subject (High Speed CMOS Logic Decade Counte CD54HC4017, CD74HC4017 Data sheet acquired from Harris Semiconductor SCHS200D November 1997 - Revised October 2003 High-Speed CMOS Logic Decade Counter/Divider with 10 Decoded Outputs Features Description • Fully Static Operation The ’HC4017 is a high speed silicon gate CMOS 5-stage Johnson counter with 10 decoded outputs. Each of the decoded outputs is normally low and sequentially goes high on the low to high transition clock period of the 10 clock period cycle. The CARRY (TC) output transitions low to high after OUTPUT 10 goes from high to low, and can be used in conjunction with the CLOCK ENABLE (CE) to cascade several stages. The CLOCK ENABLE input disables counting when in the high state. A RESET (MR) input is also provided which when taken high sets all the decoded outputs, except “0”, low. • Buffered Inputs • Common Reset • Positive Edge Clocking • Typical fMAX = 50MHz at VCC = 5V, CL = 15pF, TA = 25oC • Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads • Wide Operating Temperature Range . . . -55oC to 125oC The device can drive up to 10 low power Schottky equivalent loads. • Balanced Propagation Delay and Transition Times Ordering Information • Significant Power Reduction Compared to LSTTL Logic ICs • HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V TEMP. RANGE (oC) PACKAGE CD54HC4017F3A -55 to 125 16 Ld CERDIP CD74HC4017E -55 to 125 16 Ld PDIP CD74HC4017M -55 to 125 16 Ld SOIC CD74HC4017MT -55 to 125 16 Ld SOIC CD74HC4017M96 -55 to 125 16 Ld SOIC CD74HC4017NSR -55 to 125 16 Ld SOP CD74HC4017PW -55 to 125 16 Ld TSSOP CD74HC4017PWR -55 to 125 16 Ld TSSOP PART NUMBER NOTE: When ordering, use the entire part number. The suffixes 96 and R denote tape and reel. The suffix T denotes a small-quantity reel of 250. Pinout CD54HC4017 (CERDIP) CD74HC4017 (PDIP, SOIC, SOP, TSSOP) TOP VIEW 5 1 16 VCC 1 2 15 MR 0 3 14 CP 2 4 13 CE 6 5 12 TC 7 6 11 9 3 7 10 4 GND 8 9 8 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © 2003, Texas Instruments Incorporated 1 CD54HC4017, CD74HC4017 Functional Diagram 2 14 CLOCK 4 CLOCK 13 ENABLE 7 10 MASTER 15 RESET 1 5 6 9 11 12 0 1 2 3 4 5 6 7 DECODED DECIMAL OUT 3 8 9 TERMINAL COUNT TRUTH TABLE CP CE MR OUTPUT STATE † L X L No Change X H L No Change X X H “0” = H, “1”-”9” = L ↑ L L Increments Counter ↓ X L No Change X ↑ L No Change H ↓ L Increments Counter H = High Level L = Low Level ↑ = High to Low Transition ↓ = Low to High Transition X = Don’t Care. † If n < 5 TC = H, Otherwise = L 2 CD54HC4017, CD74HC4017 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC or IGND . . . . . . . . . . . . . . . . . .±50mA Package Thermal Impedance, θJA (see Note 1): E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67oC/W M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73oC/W NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64oC/W PW (TSSOP) Package. . . . . . . . . . . . . . . . . . . . . . . . . . 108oC/W Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. DC Electrical Specifications TEST CONDITIONS SYMBOL VI (V) IO (mA) High Level Input Voltage VIH - - Low Level Input Voltage VIL PARAMETER High Level Output Voltage CMOS Loads VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current VCC (V) 25oC -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - ±0.1 - ±1 - ±1 µA ICC VCC or GND 0 6 - - 8 - 80 - 160 µA 3 CD54HC4017, CD74HC4017 Prerequisite for Switching Specifications PARAMETER Maximum Clock Frequency CP Pulse Width MR Pulse Width Set-up Time, CE to CP Hold Time, CE to CP MR Removal Time SYMBOL TEST CONDITIONS fMAX - tW - tW - tSU - tH - tREM - VCC (V) 25oC MIN -40oC TO 85oC -55oC TO 125oC TYP MAX MIN MAX MIN MAX UNITS 2 6 - - 5 - 4 - MHz 4.5 30 - - 35 - 20 - MHz 6 35 - - 49 - 23 - MHz 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 75 - - 95 - 110 - ns 4.5 15 - - 19 - 22 - ns 6 13 - - 16 - 19 - ns 2 0 - - 0 - 0 - ns 4.5 0 - - 0 - 0 - ns 6 0 - - 0 - 0 - ns 2 5 - - 5 - 5 - ns 4.5 5 - - 5 - 5 - ns 6 5 - - 5 - 5 - ns Switching Specifications Input tr, tf = 6ns PARAMETER Propagation Delay CP to any Dec. Out CP to TC CE to any Dec. Out CE to TC TEST SYMBOL CONDITIONS tPLH, tPHL tPLH, tPHL tPLH, tPHL tPLH, tPHL -40oC TO 85oC 25oC -55oC TO 125oC VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS CL = 50pF 2 - - 230 - 290 - 345 ns CL = 50pF 4.5 - - 46 - 58 - 69 ns CL = 15pF 5 - 19 - - - - - ns CL = 50pF 6 - - 39 - 49 - 59 ns CL = 50pF 2 - - 230 - 290 - 345 ns CL = 50pF 4.5 - - 46 - 58 - 69 ns CL = 15pF 5 - 19 - - - - - ns CL = 50pF 6 - - 39 - 49 - 59 ns - - 250 - 315 - 375 ns CL = 50pF 2 CL = 50pF 4.5 - - 50 - 63 - 75 ns CL = 15pF 5 - 21 - - - - - ns CL = 50pF 6 - - 43 - 54 - 64 ns CL = 50pF 2 - - 250 - 315 - 375 ns CL = 50pF 4.5 - - 50 - 63 - 75 ns CL = 15pF 5 - 21 - - - - - ns CL = 50pF 6 - - 43 - 54 - 64 ns 4 CD54HC4017, CD74HC4017 Switching Specifications Input tr, tf = 6ns (Continued) TEST SYMBOL CONDITIONS -40oC TO 85oC 25oC -55oC TO 125oC VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS CL = 50pF 2 - - 230 - 290 - 345 ns CL = 50pF 4.5 - - 46 - 58 - 69 ns CL = 15pF 5 - 19 - - - - - ns CL = 50pF 6 - - 39 - 49 - 59 ns CL = 50pF 2 - - 230 - 290 - 345 ns CL = 50pF 4.5 - - 46 - 58 - 69 ns CL = 15pF 5 - 19 - - - - - ns CL = 50pF 6 - - 39 - 49 - 59 ns CL = 50pF 2 - - 75 - 95 - 110 ns CL = 50pF 4.5 - - 15 - 19 - 22 ns CL = 50pF 6 - - 13 - 16 - 19 ns CIN CL = 50pF - - - 10 - 10 - 10 pF Maximum CP Frequency fMAX CL = 15pF 5 - 60 - - - - - MHz Power Dissipation Capacitance (Notes 2, 3) CPD CL = 15pF 5 - 39 - - - - - pF PARAMETER MR to any Dec. Out tPLH, tPHL MR to TC tPLH, tPHL Transition Time TC, Dec. Out Input Capacitance tTLH, tTHL NOTES: 2. CPD is used to determine the dynamic power consumption, per package. 3. PD = VCC2 fi Σ€ CL VCC2 fo where fi = input frequency, fo = output frequency, CL = output load capacitance, VCC = supply voltage. Test Circuits and Waveforms tfCL trCL CLOCK 90% 10% tWL + tWH = tr = 6ns I fCL 50% VCC 90% 50% 10% INPUT VCC 50% 10% tf = 6ns 50% GND GND tTHL tWL tTLH tWH 90% 50% 10% INVERTING OUTPUT NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. tPHL FIGURE 1. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH tPLH FIGURE 2. HC TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC 5 CD54HC4017, CD74HC4017 Test Circuits and Waveforms (Continued) tfCL trCL VCC 90% CLOCK INPUT 50% 10% GND tH(H) tH(L) VCC DATA INPUT 50% GND tSU(H) tSU(L) 90% tTLH tTHL 90% 50% 10% tPLH tPHL OUTPUT tREM VCC SET, RESET OR PRESET 50% GND IC CL 50pF FIGURE 3. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS Timing Diagrams D CL CL CL P N P N CL CL CL C PN CL CLOCK MASTER RESET CLOCK ENABLE “0” “1” “2” Q “3” CL P N “4” “5” Q “6” CL 0 0 1 1 2 2 3 4 5 6 “7” 7 “8” R 8 “9” 9 TERMINAL COUNT FF DETAIL FIGURE 4. FIGURE 5. 6 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 8601101EA ACTIVE CDIP J 16 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8601101EA CD54HC4017F3A Samples CD54HC4017F3A ACTIVE CDIP J 16 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8601101EA CD54HC4017F3A Samples CD74HC4017E ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type -55 to 125 CD74HC4017E Samples CD74HC4017EE4 ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type -55 to 125 CD74HC4017E Samples CD74HC4017M ACTIVE SOIC D 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HC4017M Samples CD74HC4017M96 ACTIVE SOIC D 16 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HC4017M Samples CD74HC4017MT ACTIVE SOIC D 16 250 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HC4017M Samples CD74HC4017MTE4 ACTIVE SOIC D 16 250 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HC4017M Samples CD74HC4017NSR ACTIVE SO NS 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HC4017M Samples CD74HC4017PW ACTIVE TSSOP PW 16 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HJ4017 Samples CD74HC4017PWR ACTIVE TSSOP PW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HJ4017 Samples CD74HC4017PWRE4 ACTIVE TSSOP PW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HJ4017 Samples CD74HC4017PWT ACTIVE TSSOP PW 16 250 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 HJ4017 Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of