CLC420AE-QML

MICROCIRCUIT DATA SHEET Original Creation Date: 05/16/00 Last Update Date: 08/02/01 Last Major Revision Date: 07/18/01 MNCLC420A-X-RH REV 2A0 HIGH SPEED, VOLTAGE FEEDBACK OPERATIONAL AMPLIFIER: ALSO AVAILABLE GUARANTEED TO 300K RAD(Si) TESTED TO MIL-STD-883, METHOD 1019.5 General Description The CLC420A is an operational amplifier designed for applications requiring matched inputs and integration or transimpedance amplification. Utilizing voltage feedback architecture, the CLC420A offers a 300MHz bandwidth, a 1100V/us slew rate and a 4mA supply current (power consumption of 40mW, +5V supplies). Applications such as differential amplifiers will benefit from 70dB common mode rejection ratio and an input offset current of 0.2uA(typ). With its unity-gain stability, 2pA/SqRtHz current noise(typ), combined with a settling time of 18ns to 0.01% make the CLC420A ideal for D/A converters, pin diode receivers and photo multiplier amplifiers. All applications will find 70dB power supply rejection ratio attractive. Industry Part Number NS Part Numbers CLC420A CLC420AE-QML CLC420AJ-QML CLC420AJFQML CLC420AWG-QML CLC420AWGFQML Prime Die UB1366A Controlling Document SEE FEATURES SECTION Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Features - 300MHz small signal bandwidth 1100V/us slew rate Unity-gain stability Low distortion, -60dBc at 20MHz 0.01% settling in 18ns 0.2uA input offset current 2pASqRtHz current noise CONTROLLING DOCUMENTS: CLC420AE-QML 5962-9175801M2A CLC420AJ-QML 5962-9175801MPA CLC420AJFQML 5962F9175801MPA CLC420AWG-QML 5962-9175801MXA CLC420AWGFQML 5962F9175801MXA Applications - Active filters/integrators Differential amplifiers Pin diode receivers Log amplifiers D/A converters Photo multiplier amplifiers 2 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (V+) +7 Vdc Output Current (Iout) 70 mA Common Mode Input Voltage (Vcm) V+ Differential Input Voltage 10 V Power Dissipation (Pd) (Note 2) 112 mW Thermal Resistance (ThetaJA) Junction to Ambient LCC Ceramic DIP Ceramic SOIC (Still Air) (500 LFPM) (Still Air) (500 LFPM) (Still Air) (500 LFPM) (ThetaJC) Junction to Case LCC Ceramic DIP Ceramic SOIC Junction Temperature (Tj) 100 68 125 72 205 125 C/W C/W C/W C/W C/W C/W 25 C/W 23 C/W 24 C/W +175 C Storage Temperature Range -65 C < Ta < +150 C Lead Temperature (Soldering, 10 seconds) Package Weight (Typical) Ceramic SOIC Ceramic DIP LCC ESD Tolerance (Note 3) ESD Rating Note 1: Note 2: Note 3: +300 C 220 mg 1075 mg 470 mg 2000V Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 100pF discharged through 1.5K Ohms. 3 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Recommended Operating Conditions Supply Voltage (V+) +5 Vdc Gain Range (Av) +1 to +10 Operating Temperature Range -55 C < Ta < +125 C 4 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Electrical Characteristics DC PARAMETERS: Open Loop Characteristics (SEE NOTE 4) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL +Iin -Iin Vio Tc (+Iin) PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Input Bias Current (NonInverting) 4 -10 +10 uA 1, 2 4 -20 +20 uA 3 Input Bias Current (Inverting) 4 -10 +10 uA 1, 2 4 -20 +20 uA 3 Input Offset Voltage 4 -2.0 +2.0 mV 1 4 -3.5 +3.5 mV 2 4 -3.2 +3.2 mV 3 Average +Input Bias Current Drift 1, 4 60 nA/C 2 1, 4 120 nA/C 3 Average -Input Bias Current Drift 1, 4 60 nA/C 2 1, 4 120 nA/C 3 Tc (Vio) Average Input Offset Voltage Drift 1, 4 15 uV/C 2, 3 Iio Input Offset Current 4 -1.0 1.0 uA 1 4 -2.0 2.0 uA 2 4 -3.0 3.0 uA 3 Tc (-Iin) Tc (Iio) Aol Average Input Offset Current Drift 1, 4 10 nA/C 2 1, 4 20 nA/C 3 Open Loop Gain 4 56 dB 1, 2 4 52 dB 3 mA 1, 2, 3 Icc Quiescent Supply Current (No Load) PSRR Power Supply Rejection Ratio CMRR Rind Cind Common Mode Rejection Ratio 4 V+ = +4.5V to +5.0V, V- = -4.5V to -5.0V Vcm = +1V Differential Mode Input Resistance Differential Mode Input Capacitance 4 60 dB 1, 2 4 55 dB 3 4 65 dB 1, 2 4 60 dB 3 1, 4 1 MOhm 4, 5 1, 4 0.5 MOhm 6 1, 4 5 5.0 2 pF 4, 5, 6 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Electrical Characteristics DC PARAMETERS: Open Loop Characteristics (SEE NOTE 4) (Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL Rinc PARAMETER CONDITIONS NOTES Common Mode Input Resistance 0.25 MOhm 6 Common Mode Input Voltage 1, 4 1, 4 -Iout Rout +Vo -Vo Output Current Output Impedance Output Voltage Swing Output Voltage Swing At dc No Load SUBGROUPS 1, 4 +Vcm Output Current UNIT MOhm 4, 5 1, 4 +Iout MAX 0.5 Common Mode Input Capacitance Common Mode Input Voltage MIN 1, 4 Cinc -Vcm PINNAME 2 pF 4, 5, 6 +2.8 V 4, 5 +2.5 V 6 1, 4 -2.8 V 4, 5 1, 4 -2.5 V 6 1, 4 +50 mA 4, 5 1, 4 +30 mA 6 1, 4 -50 mA 4, 5 1, 4 -30 mA 6 1, 4 0.2 Ohm 4, 5 1, 4 0.3 Ohm 6 4 +3 V 1, 2 4 +2.8 V 3 Rl = 100 Ohms 4 +2.5 V 1, 2, 3 No Load 4 -3 V 1, 2 4 -2.8 V 3 4 -2.5 V 1, 2 4 -2.2 V 3 Rl = 100 Ohms 6 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Electrical Characteristics AC PARAMETERS: Frequency Domain Response (SEE NOTE 4) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL GFPL GFPH GFR PARAMETER Gain Flatness Peaking Low Gain Flatness Peaking High Gain Flatness Rolloff CONDITIONS NOTES At 0.1 MHz to 100 MHz, Vout < 0.4 Vpp At 100 MHz, Vout < 0.4 Vpp At 0.1 MHz to 100 MHz, Vout < 0.4 Vpp At 0.1 MHz to 30 MHz, Av = -1, Rf = 500 Ohms, Vout < 0.4 Vpp SSBW Small Signal Bandwidth -3dB bandwidth, Vout < 0.4 Vpp -3dB bandwidth, Av = -1, Rf = 500 Ohms, Vout < 0.4 Vpp LSBW Large Signal Bandwidth -3dB bandwidth, Vout < 5Vpp -3dB bandwidth, Av = -1, Rf = 500 Ohms, Vout < 5 Vpp Lpd Linear Phase Deviation At 0.1 MHz to 100 MHz 7 PINNAME MIN MAX UNIT SUBGROUPS 4 1.4 dB 4 4 1.6 dB 5 4 1.4 dB 6 4 3.0 dB 4 4 3.0 dB 5 4 5.0 dB 6 4 1.0 dB 4, 6 4 2.0 dB 5 4 1.4 dB 4 4 1.6 dB 5 4 1.4 dB 6 1, 4 200 MHz 4, 6 1, 4 130 MHz 5 4 65 MHz 4 4 65 MHz 6 4 45 MHz 5 1, 4 25 MHz 4 1, 4 20 MHz 5, 6 1, 4 35 MHz 4 1, 4 30 MHz 5, 6 1, 4 1.8 Deg. 4, 6 1, 4 2.5 Deg. 5 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Electrical Characteristics AC PARAMETERS: Distortion and Noise (SEE NOTE 4) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL HD2 PARAMETER 2nd Harmonic Distortion CONDITIONS NOTES 2 Vpp at 20 MHz 2 Vpp at 20 MHz, Av = -1 HD3 3rd Harmonic Distortion 2 Vpp at 20 MHz 2 Vpp at 20 MHz, Av = -1 Vn Icn Input Referred Noise Voltage Input Referred Noise Current At 1 MHz to 200 MHz At 1 MHz to 200 MHz PINNAME MIN MAX UNIT 4 -40 dBc 4 4 -40 dBc 5, 6 4 -40 dBc 4 4 -40 dBc 5, 6 4 -45 dBc 4, 6 4 -40 dBc 5 4 -40 dBc 4 4 -35 dBc 5 4 -40 dBc 6 1, 4 5.3 nV/sq 4, 6 1, 4 6 rtHz nV/sq 5 1, 4 2.6 rtHz pA/sq 4 1, 4 2.3 rtHz pA/sq 5 1, 4 2.9 rtHz pA/sq 6 rtHz 8 SUBGROUPS MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Electrical Characteristics AC PARAMETERS: Time Domain Response (SEE NOTE 4) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: V+ = +5 Vdc, Av = +1, Load Resistance Rl = 100 Ohms, tested parameters use Rs = 500 Ohms, otherwise, feedback resistance (Rf) = 0 Ohms. Temp. Range: -55 C < TA < +125 C. (Note 3) SYMBOL Trs Trl Ts Os +Sr -Sr PARAMETER Rise and Fall Time Rise and Fall Time Settling Time Overshoot Slew Rate Slew Rate CONDITIONS NOTES 0.4 V step, Cl < 10pF, measured between 10% and 90% points Note 4: MIN MAX UNIT SUBGROUPS 1, 4 2 nS 9, 11 1, 4 3 nS 10 0.4 V step, Av = -1, Rf = 500 Ohms, Cl < 10 pF, measured between 10% and 90% points 1, 4 5.5 nS 9, 11 1, 4 7.8 nS 10 5 V step Cl < 10 pF, measured between 10% and 90% points 1, 4 20 nS 9, 10 1, 4 25 nS 11 5 V step, Av = -1, Rf = 500 Ohms, Cl < 10 pF, measured between 10% and 90% points 1, 4 9.5 nS 9 1, 4 10 nS 10, 11 2V step at 0.01% of the final value, Cl < 10 pF 1, 4 25 nS 9, 10, 11 2V step at 0.1% of the final value, Cl < 10 pF 1, 4 18 nS 9, 10, 11 0.4 V step, Cl < 10 pF 1, 4 25 % 9, 10 1, 4 35 % 11 Rising edge, Measured +1 V with 5 V step, Cl < 10 pF 1, 4 750 V/uS 9 1, 4 600 V/uS 10, 11 Rising edge, Av = -1, Measured +1 V with 5 V step, Rf = 500 Ohms, Cl = < 10 pF 1, 4 500 V/uS 9 1, 4 430 V/uS 10, 11 Falling Edge, Measured +1 V with 5 V step, Cl < 10 pF 1, 4 750 V/uS 9 1, 4 600 V/uS 10, 11 1, 4 500 V/uS 9 1, 4 430 V/uS 10, 11 Falling Edge, Av = -1, Measured +1 V with 5 V step, Rf = 500 Ohms, Cl < 10 pF Note 1: Note 2: Note 3: PINNAME If not tested, shall be guaranteed to the limits specified. Group A testing only. The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional flow out of a device terminal. Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019.5 9 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Graphics and Diagrams GRAPHICS# DESCRIPTION 07070HRA2 CERAMIC SOIC (WG), 10 LEAD (B/I CKT) 07081HRA3 CERDIP (J), 8 LEAD (B/I CKT) 07086HRA2 LCC (E), TYPE C, 20 TERMINAL (B/I CKT) E20ARE LCC (E), TYPE C, 20 TERMINAL(P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000376A CERAMIC SOIC, 10 LEAD (PINOUT) P000430A CERDIP (J), 8 LEAD (PINOUT) P000444A LCC (E), TYPE C, 20 TERMINAL (PINOUT) WG10ARC CERAMIC SOIC (WG), 10 LEAD (P/P DWG) See attached graphics following this page. 10 NC 1 10 Vinv 2 9 +Vcc NC 3 8 NC Vnon-inv 4 7 VOUTPUT -VCC 5 6 NC CLC420AWG-QML 10 - LEAD CERAMIC SOIC CONNECTION DIAGRAM TOP VIEW P000376A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 NC N/C 1 8 N/C VINV 2 7 +VCC VNON-INV 3 6 VOUT -VCC 4 5 N/C CLC420J 8 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000430A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 N/C 4 N/C N/C N/C 3 2 N/C N/C N/C 1 20 19 18 N/C 5 17 N/C VINV 6 16 +VCC N/C 7 15 N/C VNON-INV 8 14 VOUT 9 -VCC 10 11 12 13 N/C N/C N/C N/C CLC420E 20 - LEAD LCC CONNECTION DIAGRAM TOP VIEW P000444A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 MICROCIRCUIT DATA SHEET MNCLC420A-X-RH REV 2A0 Revision History Rev ECN # Originator Changes 0A0 M0003713 07/11/01 Rel Date Rose Malone Initial MDS Release: MNCLC420A-X-RH, Rev. 0A0. Added Rad Hard Devices. and Added Min. limits to Iio test. Changed Subgroup 3 test limit from 2.6uA to 3.0uA to improve test yields. Replaces MDS: MNCLC420A-X, Rev. 0B0 1A0 M0003811 08/02/01 Rose Malone Update MDS: MNCLC420A-X-RH, Rev. 0A0 to MNCLC420A-X-RH, Rev. 1A0. Change to Electrical Section, typo in Vn parameter units change from mV/Hz to nV/sqrtHz 2A0 M0003828 08/02/01 Rose Malone Update MDS: MNCLC420A-X-RH, Rev. 1A0 to MNCLC420A-X-RH, Rev. 2A0. Electrical Section Icn parameter units column from pA/Hz to pA/sqrtHz. 11