LM2576, LM2576HV
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
LM2576xx 系列 SIMPLE SWITCHER® 3A 降压稳压器
这类稳压器不仅需要很少的外部元件,而且简单易用,
还具有故障保护和固定频率振荡器。
1 特性
• 推出更新版本产品:
– LMR33630 36V、3A、400kHz 同步转换器
– LM76003 60V、3.5A、2.2MHz 同步转换器
• 3.3V、5V、12V、15V 和可调输出版本
• 可调版本输出电压范围:1.23V 至 37V(高压版本
为 57V),在线路和负载条件下可承受最大 ±4% 的
容差
• 额定输出电流为 3A
• 宽输入电压范围:40V,高压版本可达到 60V
• 只需要四个外部元件
• 52kHz 固定频率内部振荡器
• TTL 关断功能、低功耗待机模式
• 高效率
• 使用现成的标准电感器
• 使用 LMR33630 或 LM76003 并借助 WEBENCH®
Power Designer 创建定制设计方案
2 应用
•
•
•
•
电机驱动器
商用网络和服务器 PSU
电器
测试和测量设备
LM2576 系列可为常用三端线性稳压器提供高效的替代
方案。它大幅减少了散热器尺寸,在某些情况下无需散
热器。
数家不同的生产商均可提供标准系列的电感器,它们经
优化可与 LM2576 搭配使用。此特性极大地简化了开
关模式电源的设计。
其他特性包括在额定输入电压和输出负载条件下,该器
件具有 ±4% 的输出电压容差和 ±10% 的振荡器频率容
差。具备外部关断功能,待机电流(典型值)为
50μA。输出开关具备逐周期电流限制以及在故障状况
下提供全面保护的热关断功能。
新产品 LMR33630 提供更低的 BOM 成本、更高的效
率、更小的解决方案尺寸(减小 85%)以及诸多其他
特性。LM76003 需要很少的外部元件,引脚分配设计
可简化 PCB 布局,提供更好的 EMI 和热性能。请参阅
器件比较表以比较规格。
器件信息
器件型号(1)
LM2576
LM2576HV
3 说明
LM2576 系列稳压器是为降压开关稳压器提供所有有效
功能的单片集成电路,能够驱动 3A 的负载,并且拥有
出色的线路和负载调节性能。这些器件可提供 3.3V、
5V、12V、15V 固定输出电压和可调节输出版本。
(1)
封装
封装尺寸(标称值)
TO-220 (5)
10.16mm × 8.51mm
DDPAK/TO-263 (5)
10.16mm × 8.42mm
如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
典型输出电压版本典型应用图
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SNVS107
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
Table of Contents
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................4
6.4 Thermal Information....................................................4
6.5 Electrical Characteristics: 3.3 V.................................. 5
6.6 Electrical Characteristics: 5 V..................................... 5
6.7 Electrical Characteristics: 12 V................................... 5
6.8 Electrical Characteristics: 15 V................................... 6
6.9 Electrical Characteristics: Adjustable Output
Voltage.......................................................................... 6
6.10 Electrical Characteristics: All Output Voltage
Versions.........................................................................6
6.11 Typical Characteristics.............................................. 8
7 Detailed Description......................................................12
7.1 Overview................................................................... 12
7.2 Functional Block Diagram......................................... 12
7.3 Feature Description...................................................12
7.4 Device Functional Modes..........................................14
8 Application and Implementation.................................. 15
8.1 Application Information............................................. 15
8.2 Typical Applications.................................................. 19
9 Power Supply Recommendations................................25
10 Layout...........................................................................26
10.1 Layout Guidelines................................................... 26
10.2 Layout Example...................................................... 27
10.3 Grounding............................................................... 27
10.4 Heat Sink and Thermal Considerations.................. 27
11 Device and Documentation Support..........................29
11.1 Device Support........................................................29
11.2 Documentation Support.......................................... 30
11.3 支持资源..................................................................30
11.4 接收文档更新通知................................................... 30
11.5 Trademarks............................................................. 30
11.6 Electrostatic Discharge Caution.............................. 30
11.7 Glossary.................................................................. 30
12 Mechanical, Packaging, and Orderable
Information.................................................................... 30
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision E (June 2020) to Revision F (May 2021)
Page
• 添加了 LM76003 促销信息..................................................................................................................................1
• 更新了整个文档中的表格、图和交叉参考的编号格式......................................................................................... 1
Changes from Revision D (January 2016) to Revision E (June 2020)
Page
• 添加了有关 LMR33630 的信息........................................................................................................................... 1
Changes from Revision C (April 2013) to Revision D (January 2016)
Page
• 添加了 ESD 等级 表、特性说明 部分、器件功能模式、应用和实施 部分、电源相关建议 部分、布局 部分、器
件和文档支持 部分以及机械、封装和可订购信息 部分....................................................................................... 1
• Moved the thermal resistance data from the Electrical Characteristics: All Output Voltage Versions table to
the Thermal Information table.............................................................................................................................4
Changes from Revision B (April 2013) to Revision C (April 2013)
Page
• Changed layout of National Data Sheet to TI format.......................................................................................... 3
2
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
5 Pin Configuration and Functions
图 5-1. KC Package 5-Pin TO-220 Top View
图 5-2. KTT Package 5-PIN DDPAK/TO-263 Top
View
图 5-3. DDPAK/TO-263 (S) Package 5-Lead SurfaceMount Package Top View
表 5-1. Pin Functions
PIN
NO.
NAME
I/O(1)
DESCRIPTION
1
VIN
I
Supply input pin to collector pin of high-side transistor. Connect to power supply and input
bypass capacitors CIN. Path from VIN pin to high frequency bypass CIN and GND must be as
short as possible.
2
OUTPUT
O
Emitter pin of the power transistor. This is a switching node. Attached this pin to an inductor
and the cathode of the external diode.
3
GROUND
—
Ground pin. Path to CIN must be as short as possible.
4
FEEDBACK
I
Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT for ADJ
version or connect this pin directly to the output capacitor for a fixed output version.
5
ON/OFF
I
Enable input to the voltage regulator. High = OFF and low = ON. Connect to GND to enable
the voltage regulator. Do not leave this pin float.
—
TAB
—
(1)
Connected to GND. Attached to heatsink for thermal relief for TO-220 package or put a
copper plane connected to this pin as a thermal relief for DDPAK package.
I = INPUT, O = OUTPUT
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
3
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
6 Specifications
6.1 Absolute Maximum Ratings
over the recommended operating junction temperature range of -40°C to 125°C (unless otherwise noted)(1) (2)
MIN
Maximum supply voltage
MAX
LM2576
45
LM2576HV
63
Output voltage to ground
V
−1
(Steady-state)
Power dissipation
V
Internally Limited
Maximum junction temperature, TJ
−65
Storage temperature, Tstg
(2)
V
−0.3V ≤ V ≤ +VIN
ON /OFF pin input voltage
(1)
UNIT
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
6.2 ESD Ratings
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
VALUE
UNIT
±2000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over the recommended operating junction temperature range of -40°C to 125°C (unless otherwise noted)
Temperature
LM2576, LM2576HV
Supply voltage
MIN
MAX
UNIT
−40
125
°C
LM2576
40
LM2576HV
60
V
6.4 Thermal Information
LM2576, LM2576HV
THERMAL
KTT (TO-263)
KC (TO-220)
5 PINS
5 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
42.6
32.4
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
43.3
41.2
°C/W
RθJB
Junction-to-board thermal resistance
22.4
17.6
°C/W
ψJT
Junction-to-top characterization parameter
10.7
7.8
°C/W
ψJB
Junction-to-board characterization parameter
21.3
17
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
0.4
0.4
°C/W
(1)
(2)
(3)
4
METRIC(1) (2) (3)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953 and the Using New Thermal Metrics applications report, SBVA025.
The package thermal impedance is calculated in accordance with JESD 51-7
Thermal Resistances were simulated on a 4-layer, JEDEC board.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
6.5 Electrical Characteristics: 3.3 V
Specifications are for TJ = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT 图 8-3 and 图
Output Voltage
VIN = 12 V, ILOAD = 0.5 A
Circuit of 图 8-3 and 图 8-9
Output Voltage: LM2576
6 V ≤ VIN ≤ 40 V, 0.5 A ≤
ILOAD ≤ 3 A
Circuit of 图 8-3 and 图 8-9
Output Voltage: LM2576HV
6 V ≤ VIN ≤ 60 V, 0.5 A ≤
ILOAD ≤ 3 A
Circuit of 图 8-3 and 图 8-9
Efficiency
VIN = 12 V, ILOAD = 3 A
VOUT
η
(1)
MIN
TYP
MAX
UNIT
3.234
3.3
3.366
V
TJ = 25°C
3.168
3.3
3.432
Applies over full
operating temperature
range
3.135
TJ = 25°C
3.168
Applies over full
operating temperature
range
3.135
8-9(1)
3.465
3.3
V
3.45
3.482
V
75%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in 图 8-3 and 图 8-9, system performance is as shown in 节 6.10.
6.6 Electrical Characteristics: 5 V
Specifications are for TJ = 25°C for the 图 8-3 and 图 8-9 (unless otherwise noted).
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT 图 8-3 and 图
VOUT
Output Voltage
VIN = 12 V, ILOAD = 0.5 A
Circuit of 图 8-3 and 图 8-9
VOUT
Output Voltage
LM2576
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 40 V
Circuit of 图 8-3 and 图 8-9
VOUT
Output Voltage
LM2576HV
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 60 V
Circuit of 图 8-3 and 图 8-9
η
Efficiency
VIN = 12 V, ILOAD = 3 A
(1)
MIN
TYP
MAX
4.9
5
5.1
4.8
5
5.2
UNIT
8-9(1)
TJ = 25°C
Applies over full
operating temperature
range
TJ = 25°C
Applies over full
operating temperature
range
4.75
4.8
5.25
5
5.225
V
V
4.75
5.275
V
77%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in 图 8-3 and 图 8-9, system performance is as shown in 节 6.10.
6.7 Electrical Characteristics: 12 V
Specifications are for TJ = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT 图 8-3 and 图
MIN
TYP
MAX
UNIT
11.76
12
12.24
V
11.52
12
12.48
8-9(1)
VOUT
Output Voltage
VIN = 25 V, ILOAD = 0.5 A
Circuit of 图 8-3 and 图 8-9
VOUT
Output Voltage
LM2576
0.5 A ≤ ILOAD ≤ 3 A,
15 V ≤ VIN ≤ 40 V
Circuit of 图 8-3 and 图 8-9
and
VOUT
Output Voltage
LM2576HV
0.5 A ≤ ILOAD ≤ 3 A,
15 V ≤ VIN ≤ 60 V
Circuit of 图 8-3 and 图 8-9
TJ = 25°C
Applies over full
operating temperature
range
TJ = 25°C
Applies over full
operating temperature
range
11.4
11.52
11.4
12.6
12
V
12.54
12.66
V
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
5
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
Specifications are for TJ = 25°C (unless otherwise noted).
PARAMETER
η
(1)
Efficiency
TEST CONDITIONS
MIN
VIN = 15 V, ILOAD = 3 A
TYP
MAX
UNIT
88%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in 图 8-3 and 图 8-9, system performance is as shown in 节 6.10.
6.8 Electrical Characteristics: 15 V
over operating free-air temperature range (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
14.7
15
15.3
V
14.4
15
15.6
SYSTEM PARAMETERS TEST CIRCUIT 图 8-3 and 图 8-9(1)
VOUT
Output Voltage
VIN = 25 V, ILOAD = 0.5 A
Circuit of 图 8-3 and 图 8-9
VOUT
Output Voltage
LM2576
0.5 A ≤ ILOAD ≤ 3 A,
18 V ≤ VIN ≤ 40 V
Circuit of 图 8-3 and 图 8-9
VOUT
Output Voltage
LM2576HV
0.5 A ≤ ILOAD ≤ 3 A,
18 V ≤ VIN ≤ 60 V
Circuit of 图 8-3 and 图 8-9
η
Efficiency
VIN = 18 V, ILOAD = 3 A
(1)
TJ = 25°C
Applies over full
operating temperature
range
14.25
TJ = 25°C
Applies over full
operating temperature
range
15.75
14.4
15
15.68
V
14.25
15.83
V
88%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in 图 8-3 and 图 8-9, system performance is as shown in 节 6.10.
6.9 Electrical Characteristics: Adjustable Output Voltage
over operating free-air temperature range (unless otherwise noted).
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT 图 8-3 and 图
VOUT
Feedback voltage
VIN = 12 V, ILOAD = 0.5 A
VOUT = 5 V,
Circuit of 图 8-3 and 图 8-9
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 40 V
VOUT = 5 V, Circuit of 图 8-3
and 图 8-9
TJ = 25°C
Feedback Voltage
LM2576
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 60 V
VOUT = 5 V, Circuit of 图 8-3
and 图 8-9
TJ = 25°C
Feedback Voltage
LM2576HV
η
Efficiency
VIN = 12 V, ILOAD = 3 A, VOUT = 5 V
(1)
MIN
TYP
MAX
UNIT
1.217
1.23
1.243
V
1.193
1.23
1.267
8-9(1)
Applies over full
operating temperature
range
1.18
1.193
Applies over full
operating temperature
range
1.28
1.23
1.18
V
1.273
1.286
V
77%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in 图 8-3 and 图 8-9, system performance is as shown in 节 6.10.
6.10 Electrical Characteristics: All Output Voltage Versions
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT 图 8-3 and 图
Ib
6
Feedback Bias Current
MIN
TYP(1)
MAX
UNIT
8-9(2)
VOUT = 5 V (Adjustable
Version Only)
TJ = 25°C
100
Applies over full
operating
temperature range
500
Submit Document Feedback
50
nA
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
over operating free-air temperature range (unless otherwise noted)
PARAMETER
fO
Oscillator Frequency(7)
TEST CONDITIONS
MIN
TJ = 25°C
47
Applies over full operating temperature range
42
TJ = 25°C
VSAT
Saturation Voltage
DC
Max Duty Cycle (ON)(4)
ICL
Current Limit(3) (7)
IL
Output Leakage Current
IQ
Quiescent Current(5)
ISTBY
Standby Quiescent
Current
IOUT = 3 A
TYP(1)
52
1.4
93%
98%
4.2
5.8
Applies over full operating temperature range
3.5
2
ON /OFF Pin = 5 V (OFF)
UNIT
kHz
1.8
2
TJ = 25°C
Output = 0 V
Output = −1 V
Output = −1 V (5) (6)
58
63
Applies over full
operating
temperature range
(3)
MAX
6.9
7.5
V
A
7.5
30
mA
5
10
mA
50
200
μA
ON /OFF CONTROL TEST CIRCUIT 图 8-3 and 图 8-9
VOUT = 0 V
VIH
ON /OFF Pin
Logic Input Level
VIL
IIH
IIL
(1)
(2)
(3)
(4)
(5)
(6)
(7)
ON /OFF Pin Input
Current
VOUT = Nominal Output
Voltage
TJ = 25°C
2.2
Applies over full
operating
temperature range
2.4
TJ = 25°C
1.4
V
1.2
Applies over full
operating
temperature range
1
0.8
V
ON /OFF Pin = 5 V (OFF)
12
30
μA
ON /OFF Pin = 0 V (ON)
0
10
μA
All limits specified at room temperature (25°C) unless otherwise noted. All room temperature limits are 100% production tested. All
limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods.
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in 图 8-3 and 图 8-9, system performance is as shown in 节 6.10.
Output pin sourcing current. No diode, inductor or capacitor connected to output.
Feedback pin removed from output and connected to 0V.
Feedback pin removed from output and connected to +12 V for the Adjustable, 3.3-V, and 5-V versions, and +25 V for the 12-V and 15V versions, to force the output transistor OFF.
VIN = 40 V (60 V for high voltage version).
The oscillator frequency reduces to approximately 11 kHz in the event of an output short or an overload which causes the regulated
output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power
dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2%.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
7
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
6.11 Typical Characteristics
(Circuit of 图 8-3 and 图 8-9)
8
图 6-1. Normalized Output Voltage
图 6-2. Line Regulation
图 6-3. Dropout Voltage
图 6-4. Current Limit
图 6-5. Quiescent Current
图 6-6. Standby Quiescent Current
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
图 6-7. Oscillator Frequency
图 6-8. Switch Saturation Voltage
图 6-10. Minimum Operating Voltage
图 6-9. Efficiency
图 6-11. Quiescent Current vs Duty Cycle
图 6-12. Feedback Voltage vs Duty Cycle
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
9
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
图 6-13. Minimum Operating Voltage
图 6-14. Quiescent Current vs Duty Cycle
图 6-15. Feedback Voltage vs Duty Cycle
图 6-16. Feedback Pin Current
If the DDPAK/TO-263 package is used, the thermal resistance
can be reduced by increasing the PCB copper area thermally
connected to the package. Using 0.5 square inches of copper
VOUT = 15 V A: Output Pin Voltage, 50 V/div B: Output Pin
Current, 2 A/div C: Inductor Current, 2 A/div D: Output Ripple
Voltage, 50 mV/div, AC-CoupledHorizontal Time Base: 5
μs/div
图 6-18. Switching Waveforms
area, θJA is 50°C/W, with 1 square inch of copper area, θJA is
37°C/W, and with 1.6 or more square inches of copper area,
θJA is 32°C/W.
图 6-17. Maximum Power Dissipation (DDPAK/
TO-263)
10
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
图 6-19. Load Transient Response
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
11
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
7 Detailed Description
7.1 Overview
The LM2576 SIMPLE SWITCHER® regulator is an easy-to-use, non-synchronous step-down DC-DC converter
with a wide input voltage range from 40 V to up to 60 V for a HV version. It is capable of delivering up to 3-A DC
load current with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V,
5 V, 12 V, 15 V, and an adjustable output version. The family requires few external components, and the pin
arrangement was designed for simple, optimum PCB layout.
7.2 Functional Block Diagram
VIN
Unregulated
DC Input
Internal
Rgulator
1
+
CIN
ON/OFF
ON/OFF
5
4
Feedback
R2
+
Fixed Gain
Error Amp
3 Amp
Switch
Comparator
+
R1
1k
±
Driver
±
OUTPUT
L1
2
D1
1.23 V
BAND-GAP
REFERENCE
52 kHZ
OSCILLATOR
RESET
THERMAL
SHUTDOWN
CURRENT
LIMIT
VOUT
+
COUT
3
L
O
A
D
GND
3.3 V R2 = 1.7 k 5 V, R2 = 3.1 k 12 V, R2 = 8.84 k 15 V, R2 = 11.3 k For ADJ. Version R1 = Open, R2 = 0 Ω Patent Pending
7.3 Feature Description
7.3.1 Undervoltage Lockout
In some applications it is desirable to keep the regulator off until the input voltage reaches a certain threshold. 图
7-1 shows an undervoltage lockout circuit that accomplishes this task, while 图 7-2 shows the same circuit
applied to a buck-boost configuration. These circuits keep the regulator off until the input voltage reaches a
predetermined level.
VTH ≈ VZ1 + 2VBE(Q1)
12
(1)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
+VIN
+VIN
R1
20 k
LM2576-XX
1
+
CIN
20 k
5
ON/OFF
3
GND
Z1
Q1
R2
10 k
Complete circuit not shown.
图 7-1. Undervoltage Lockout for Buck Circuit
+VIN
+VIN
R1
20 k
LM2576-XX
1
+
CIN
20 k
5
ON/OFF
3
GND
Z1
Q1
R2
10 k
-VOUT
Complete circuit not shown (see 图 8-1).
图 7-2. Undervoltage Lockout for Buck-Boost Circuit
7.3.2 Delayed Start-Up
The ON /OFF pin can be used to provide a delayed start-up feature as shown in 图 7-3. With an input voltage of
20 V and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit
begins switching. Increasing the RC time constant can provide longer delay times. But excessively large RC time
constants can cause problems with input voltages that are high in 60-Hz or 120-Hz ripple, by coupling the ripple
into the ON /OFF pin.
7.3.3 Adjustable Output, Low-Ripple Power Supply
图 7-4 shows a 3-A power supply that features an adjustable output voltage. An additional LC filter that reduces
the output ripple by a factor of 10 or more is included in this circuit.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
13
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
+VIN
+VIN
+
CD
LM2576-XX
1
0.1 …F
+
CIN
5
ON/OFF
3
GND
100 …F
RD
47 K
Complete circuit not shown.
图 7-3. Delayed Start-Up
Feedback
55 V
Unregulated
DC Input
4
+VIN
LM2576HV-ADJ
1
+
CIN
Output
3
GND
100 …F
5
2
ON/OFF
Output
Voltage
L1
150 µH
+
D1
1N5822
COUT
R2
50 k
+1.2 to 50 V
@3A
20 µH
+
2000 …F
C1
100 …F
R1
1.21 k
optional output ripple filter
图 7-4. 1.2-V to 55-V Adjustable 3-A Power Supply With Low Output Ripple
7.4 Device Functional Modes
7.4.1 Shutdown Mode
The ON/OFF pin provides electrical ON and OFF control for the LM2576. When the voltage of this pin is higher
than 1.4 V, the device is in shutdown mode. The typical standby current in this mode is 50 μA.
7.4.2 Active Mode
When the voltage of the ON/OFF pin is below 1.2 V, the device starts switching, and the output voltage rises until
it reaches the normal regulation voltage.
7.4.3 Current Limit
The LM2576 device has current limiting to prevent the switch current from exceeding safe values during an
accidental overload on the output. This current limit value can be found in 节 6.10 under the heading of ICL.
The LM2576 uses cycle-by-cycle peak current limit for overload protection. This helps to prevent damage to the
device and external components. The regulator operates in current limit mode whenever the inductor current
exceeds the value of ICL given in 节 6.10. This occurs if the load current is greater than 3 A, or the converter is
starting up. Keep in mind that the maximum available load current depends on the input voltage, output voltage,
and inductor value. The regulator also incorporates short-circuit protection to prevent inductor current run-away.
When the voltage on the FB pin (ADJ) falls below about 0.58 V the switching frequency is dropped to about 11
kHz. This allows the inductor current to ramp down sufficiently during the switch OFF-time to prevent saturation.
14
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
8.1 Application Information
8.1.1 Input Capacitor (CIN)
To maintain stability, the regulator input pin must be bypassed with at least a 100-μF electrolytic capacitor. The
capacitor's leads must be kept short, and placed near the regulator.
If the operating temperature range includes temperatures below −25°C, the input capacitor value may need to be
larger. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower
temperatures and age. Paralleling a ceramic or solid tantalum capacitor increases the regulator stability at cold
temperatures. For maximum capacitor operating lifetime, the RMS ripple current rating of the capacitor must be
greater than:
(2)
8.1.2 Inductor Selection
All switching regulators have two basic modes of operation: continuous and discontinuous. The difference
between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a
period of time in the normal switching cycle. Each mode has distinctively different operating characteristics,
which can affect the regulator performance and requirements.
The LM2576 (or any of the SIMPLE SWITCHER® family can be used for both continuous and discontinuous
modes of operation.
The inductor value selection guides in 图 8-4 through 图 8-8 are designed for buck regulator designs of the
continuous inductor current type. When using inductor values shown in the inductor selection guide, the peak-topeak inductor ripple current is approximately 20% to 30% of the maximum DC current. With relatively heavy load
currents, the circuit operates in the continuous mode (inductor current always flowing), but under light load
conditions, the circuit is forced to the discontinuous mode (inductor current falls to zero for a period of time). This
discontinuous mode of operation is perfectly acceptable. For light loads (less than approximately 300 mA), it may
be desirable to operate the regulator in the discontinuous mode, primarily because of the lower inductor values
required for the discontinuous mode.
The selection guide chooses inductor values suitable for continuous mode operation, but if the inductor value
chosen is prohibitively high, the designer should investigate the possibility of discontinuous operation.
Inductors are available in different styles such as pot core, toriod, E-frame, bobbin core, and so on, as well as
different core materials, such as ferrites and powdered iron. The bobbin core is the least expensive type, and
consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor;
however, because the magnetic flux is not completely contained within the core, the bobbin core generates more
electromagnetic interference (EMI). This EMI can cause problems in sensitive circuits, or can give incorrect
scope readings because of induced voltages in the scope probe.
The inductors listed in the selection chart include ferrite pot core construction for AIE, powdered iron toroid for
Pulse Engineering, and ferrite bobbin core for Renco.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
15
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
An inductor must not operate beyond its maximum-rated current because it may saturate. When an inductor
begins to saturate, the inductance decreases rapidly, and the inductor begins to look mainly resistive (the DC
resistance of the winding), causing the switch current to rise very rapidly. Different inductor types have different
saturation characteristics, and this must be considered when selecting an inductor.
The inductor manufacturer's data sheets include current and energy limits to avoid inductor saturation.
8.1.3 Inductor Ripple Current
When the switcher is operating in the continuous mode, the inductor current waveform ranges from a triangular
to a sawtooth type of waveform (depending on the input voltage). For a given input voltage and output voltage,
the peak-to-peak amplitude of this inductor current waveform remains constant. As the load current rises or falls,
the entire sawtooth current waveform also rises or falls. The average DC value of this waveform is equal to the
DC load current (in the buck regulator configuration).
If the load current drops to a low enough level, the bottom of the sawtooth current waveform reaches zero, and
the switcher changes to a discontinuous mode of operation. This is a perfectly acceptable mode of operation.
Any buck switching regulator (no matter how large the inductor value is) is forced to run discontinuous if the load
current is light enough.
8.1.4 Output Capacitor
An output capacitor is required to filter the output voltage and is needed for loop stability. The capacitor must be
placed near the LM2576 using short PCB traces. Standard aluminum electrolytics are usually adequate, but TI
recommends low ESR types for low output ripple voltage and good stability. The ESR of a capacitor depends on
many factors, including: the value, the voltage rating, physical size, and the type of construction. In general, low
value or low voltage (less than 12 V) electrolytic capacitors usually have higher ESR numbers.
The amount of output ripple voltage is primarily a function of the ESR (Equivalent Series Resistance) of the
output capacitor and the amplitude of the inductor ripple current (ΔIIND). See 节 8.1.3.
The lower capacitor values (220 μF to 1000 μF) allows typically 50 mV to 150 mV of output ripple voltage,
while larger-value capacitors reduces the ripple to approximately 20 mV to 50 mV.
Output Ripple Voltage = (ΔIIND) (ESR of COUT)
(3)
To further reduce the output ripple voltage, several standard electrolytic capacitors may be paralleled, or a
higher-grade capacitor may be used. Such capacitors are often called high-frequency, low-inductance, or lowESR. These reduces the output ripple to 10 mV or 20 mV. However, when operating in the continuous mode,
reducing the ESR below 0.03 Ω can cause instability in the regulator.
Tantalum capacitors can have a very low ESR, and must be carefully evaluated if it is the only output capacitor.
Because of their good low temperature characteristics, a tantalum can be used in parallel with aluminum
electrolytics, with the tantalum making up 10% or 20% of the total capacitance.
The ripple current rating of the capacitor at 52 kHz should be at least 50% higher than the peak-to-peak inductor
ripple current.
8.1.5 Catch Diode
Buck regulators require a diode to provide a return path for the inductor current when the switch is off. This diode
must be placed close to the LM2576 using short leads and short printed-circuit traces.
Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency,
especially in low output voltage switching regulators (less than 5 V). Fast-recovery, high-efficiency, or ultra-fast
recovery diodes are also suitable, but some types with an abrupt turnoff characteristic may cause instability and
EMI problems. A fast-recovery diode with soft recovery characteristics is a better choice. Standard 60-Hz diodes
(for example, 1N4001 or 1N5400, and so on) are also not suitable. See 表 8-3 for Schottky and soft fast-recovery
diode selection guide.
16
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
8.1.6 Output Voltage Ripple and Transients
The output voltage of a switching power supply contains a sawtooth ripple voltage at the switcher frequency,
typically about 1% of the output voltage, and may also contain short voltage spikes at the peaks of the sawtooth
waveform.
The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output
capacitor (see 节 8.1.2).
The voltage spikes are present because of the fast switching action of the output switch, and the parasitic
inductance of the output filter capacitor. To minimize these voltage spikes, special low inductance capacitors can
be used, and their lead lengths must be kept short. Wiring inductance, stray capacitance, as well as the scope
probe used to evaluate these transients, all contribute to the amplitude of these spikes.
An additional small LC filter (20 μH and 100 μF) can be added to the output (as shown in 图 7-4) to further
reduce the amount of output ripple and transients. A 10 × reduction in output ripple voltage and transients is
possible with this filter.
8.1.7 Feedback Connection
The LM2576 (fixed voltage versions) feedback pin must be wired to the output voltage point of the switching
power supply. When using the adjustable version, physically locate both output voltage programming resistors
near the LM2576 to avoid picking up unwanted noise. Avoid using resistors greater than 100 kΩ because of the
increased chance of noise pickup.
8.1.8 ON /OFF INPUT
For normal operation, the ON /OFF pin must be grounded or driven with a low-level TTL voltage (typically below
1.6 V). To put the regulator into standby mode, drive this pin with a high-level TTL or CMOS signal. The
ON /OFF pin can be safely pulled up to +VIN without a resistor in series with it. The ON /OFF pin must not be left
open.
8.1.9 Inverting Regulator
图 8-1 shows a LM2576-12 in a buck-boost configuration to generate a negative 12-V output from a positive
input voltage. This circuit bootstraps the ground pin of the regulator to the negative output voltage, then by
grounding the feedback pin, the regulator senses the inverted output voltage and regulates it to −12 V.
For an input voltage of 12 V or more, the maximum available output current in this configuration is approximately
700 mA. At lighter loads, the minimum input voltage required drops to approximately 4.7 V.
The switch currents in this buck-boost configuration are higher than in the standard buck-mode design, thus
lowering the available output current. Also, the start-up input current of the buck-boost converter is higher than
the standard buck-mode regulator, and this may overload an input power source with a current limit less than
5 A. Using a delayed turn-on or an undervoltage lockout circuit (described in 节 8.1.10) would allow the input
voltage to rise to a high enough level before the switcher would be allowed to turn on.
Because of the structural differences between the buck and the buck-boost regulator topologies, the buck
regulator design procedure section can not be used to select the inductor or the output capacitor. The
recommended range of inductor values for the buck-boost design is between 68 μH and 220 μH, and the
output capacitor values must be larger than what is normally required for buck designs. Low input voltages or
high output currents require a large value output capacitor (in the thousands of micro Farads).
The peak inductor current, which is the same as the peak switch current, can be calculated in 方程式 4:
(4)
where
• fosc = 52 kHz
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
17
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
Under normal continuous inductor current operating conditions, the minimum VIN represents the worst case.
Select an inductor that is rated for the peak current anticipated.
+12 To +45 V
Unregulated
DC Input
Feedback
4
+VIN
LM2576HV-ADJ
+
L1
Output
1
CIN
100 …F 3
GND
2
ON/OFF
5
68 µH
+
D1
1N5822
COUT
2200 …F
-12 @ 0.7 A
REGULATED
DC INPUT
图 8-1. Inverting Buck-Boost Develops −12 V
Also, the maximum voltage appearing across the regulator is the absolute sum of the input and output voltage.
For a −12-V output, the maximum input voltage for the LM2576 is +28 V, or +48 V for the LM2576HV.
8.1.10 Negative Boost Regulator
Another variation on the buck-boost topology is the negative boost configuration. The circuit in 图 8-2 accepts an
input voltage ranging from −5 V to −12 V and provides a regulated −12-V output. Input voltages greater than −12
V causes the output to rise above −12 V, but does not damage the regulator.
+
Feedback
VIN
LM2576-12
1
4
Output
LOW ESR
2
+
3
GND
CIN
5
ON/OFF
COUT
2200 PF
1N5820
100 PF
VOUT = -12 V
100 PH
-VIN
-5 V to -12 V
Typical Load Current 400 mA for VIN = −5.2 V 750 mA for VIN = −7 V Heat sink may be required.
图 8-2. Negative Boost
Because of the boosting function of this type of regulator, the switch current is relatively high, especially at low
input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also,
boost regulators can not provide current-limiting load protection in the event of a shorted load, so some other
means (such as a fuse) may be necessary.
18
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
8.2 Typical Applications
8.2.1 Fixed Output Voltage Version
Feedback
+VIN
LM2576HVFixed Output
4
Output
1
VIN
UNREGULATED
DC INPUT
2
+ 100 …F
GND
3
CIN
ON/OFF
VOUT
L1
100 µH
5
D1
MBR360
+
COUT
1000 µF
L
O
A
D
CIN — 100-μF, 75-V, Aluminum Electrolytic COUT — 1000-μF, 25-V, Aluminum Electrolytic D1 — Schottky, MBR360 L1 — 100 μH,
Pulse Eng. PE-92108 R1 — 2 k, 0.1% R2 — 6.12 k, 0.1%
图 8-3. Fixed Output Voltage Versions
8.2.1.1 Design Requirements
表 8-1 lists the design parameters of this example.
表 8-1. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Regulated Output Voltage
(3.3 V, 5 V, 12 V, or 15 V), VOUT
5V
Maximum Input Voltage, VIN(Max)
15 V
Maximum Load Current,
ILOAD(Max)
3A
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Custom Design with WEBENCH Tools
Click here to create a custom design using the WEBENCH® Power Designer.
1. Start by entering your VIN, VOUT and IOUT requirements.
2. Optimize your design for key parameters like efficiency, footprint and cost using the optimizer dial and
compare this design with other possible solutions from Texas Instruments.
3. WEBENCH Power Designer provides you with a customized schematic along with a list of materials with real
time pricing and component availability.
4. In most cases, you will also be able to:
• Run electrical simulations to see important waveforms and circuit performance,
• Run thermal simulations to understand the thermal performance of your board,
• Export your customized schematic and layout into popular CAD formats,
• Print PDF reports for the design, and share your design with colleagues.
8.2.1.2.2 Inductor Selection (L1)
1. Select the correct Inductor value selection guide from 图 8-4, 图 8-5, 图 8-6, or 图 8-7. (Output voltages of
3.3 V, 5 V, 12 V or 15 V respectively). For other output voltages, see the design procedure for the adjustable
version. Use the selection guide shown in 图 8-5.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
19
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
2. From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and
ILOAD(Max), and note the inductor code for that region. From the selection guide, the inductance area
intersected by the 15-V line and 3-A line is L100.
3. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in
图 8-4. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for
operation at the LM2576 switching frequency (52 kHz) and for a current rating of 1.15 × ILOAD. For additional
inductor information, see 节 8.1.2. Inductor value required is 100 μH from the table in 图 8-4. Choose AIE
415-0930, Pulse Engineering PE92108, or Renco RL2444.
8.2.1.2.3 Output Capacitor Selection (COUT)
1. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation and an acceptable output ripple voltage, (approximately 1% of the output
voltage) TI recommends a value between 100 μF and 470 μF. We choose COUT = 680-μF to 2000-μF
standard aluminum electrolytic.
2. The voltage rating of the capacitor must be at least 1.5 times greater than the output voltage. For a 5-V
regulator, a rating of at least 8 V is appropriate, and a 10-V or 15-V rating is recommended. Capacitor
voltage rating = 20 V. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this
reason it may be necessary to select a capacitor rated for a higher voltage than would normally be needed.
8.2.1.2.4 Catch Diode Selection (D1)
1. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode should have a current rating equal
to the maximum current limit of the LM2576. The most stressful condition for this diode is an overload or
shorted output condition. For this example, a 3-A current rating is adequate.
2. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. Use a 20-V
1N5823 or SR302 Schottky diode, or any of the suggested fast-recovery diodes shown in 表 8-3.
8.2.1.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 100-μF, 25-V aluminum electrolytic capacitor located near the input and ground pins provides
sufficient bypassing.
20
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
8.2.1.3 Application Curves
图 8-4. LM2576(HV)-3.3
图 8-5. LM2576(HV)-5.0
图 8-6. LM2576(HV)-12
图 8-7. LM2576(HV)-15
图 8-8. LM2576(HV)-ADJ
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
21
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
8.2.2 Adjusted Output Voltage Version
Feedback
+VIN
LM2576HVADJ
4
Output
1
7 V ± 60 V
UNREGULATED
DC INPUT
2
+ 100 …F
GND
CIN
3
ON/OFF
VOUT
5V
L1
100 µH
+
5
D1
MBR360
COUT
1000 µF
R2
R1
L
O
A
D
where VREF = 1.23 V, R1 between 1 k and 5 k
图 8-9. Adjustable Output Voltage Version
8.2.2.1 Design Requirements
表 8-2 lists the design parameters of this example.
表 8-2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Regulated Output Voltage, VOUT
10 V
Maximum Input Voltage, VIN(Max)
25 V
Maximum Load Current,
ILOAD(Max)
3A
Switching Frequency, F
Fixed at 52 kHz
8.2.2.2 Detailed Design Procedure
8.2.2.2.1 Programming Output Voltage
Select R1 and R2, as shown in 图 8-9.
Use 方程式 5 to select the appropriate resistor values.
(5)
R1 can be between 1k and 5k. (For best temperature coefficient and stability with time, use 1% metal film
resistors)
(6)
(7)
R2 = 1 k (8.13 − 1) = 7.13 k, closest 1% value is 7.15 k
8.2.2.2.2 Inductor Selection (L1)
1. Calculate the inductor Volt • microsecond constant, E • T (V • μs), from 方程式 8:
22
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
EuT
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
VIN
V OUT
V OUT
VIN
u
1000
F in kHz
Vu V
(8)
Calculate E • T (V • μs)
EuT
25 10 u
10 1000
u
25
52
115 V u V
(9)
2. Use the E • T value from the previous formula and match it with the E • T number on the vertical axis of the
Inductor value selection guide shown in 图 8-8.
E • T = 115 V • μs
3. On the horizontal axis, select the maximum load current.
ILOAD(Max) = 3 A
4. Identify the inductance region intersected by the E • T value and the maximum load current value, and note
the inductor code for that region.
Inductance Region = H150
5. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in
表 8-4. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for
operation at the LM2576 switching frequency (52 kHz) and for a current rating of 1.15 × ILOAD. For additional
inductor information, see 节 8.1.2.
Inductor Value = 150 μH
Choose from AIE part #415-0936, Pulse Engineering part #PE-531115, or Renco part #RL2445.
8.2.2.2.3 Output Capacitor Selection (COUT)
1. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation, the capacitor must satisfy 方程式 10:
COUT t 13,300
VIN Max
V OUT u L
+
)
方程式 10 yields capacitor values between 10 μF and 2200 μF that satisfies the loop requirements for
stable operation. But to achieve an acceptable output ripple voltage, (approximately 1% of the output
voltage) and transient response, the output capacitor may need to be several times larger than 方程式 10
yields.
COUT t 13,300
25
10 u 150
22.2 )
However, for acceptable output ripple voltage select
COUT ≥ 680 μF
COUT = 680-μF electrolytic capacitor
2. The capacitor's voltage rating must be at last 1.5 times greater than the output voltage. For a 10-V regulator,
a rating of at least 15 V or more is recommended. Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reason it may be necessary to select a capacitor rate for a higher voltage than
would normally be needed.
8.2.2.2.4 Catch Diode Selection (D1)
1. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode must have a current rating equal to
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
23
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
the maximum current limit of the LM2576. The most stressful condition for this diode is an overload or
shorted output. See 表 8-3. For this example, a 3.3-A current rating is adequate.
2. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. Use a 30-V
31DQ03 Schottky diode, or any of the suggested fast-recovery diodes in 表 8-3.
8.2.2.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 100-μF aluminum electrolytic capacitor located near the input and ground pins provides sufficient
bypassing.
表 8-3. Diode Selection Guide
SCHOTTKY
VR
3A
FAST RECOVERY
4 A to 6 A
3A
4 A to 6 A
The following
diodes are all
rated to 100-V
31DF1
HER302
The following
diodes are all
rated to 100-V
50WF10
MUR410
HER602
1N5820
20 V
MBR320P
1N5823
SR302
1N5821
MBR330
30 V
50WQ03
1N5824
31DQ03
SR303
1N5822
MBR340
50WQ04
1N5825
MBR340
40 V
31DQ04
SR304
MBR350
50 V
31DQ05
50WQ05
SR305
MBR360
60 V
50WR06
50SQ060
DQ06
SR306
表 8-4. Inductor Selection by Manufacturer's Part Number
24
INDUCTOR CODE
INDUCTOR VALUE
SCHOTT(1)
PULSE ENG.(2)
RENCO(3)
L47
47 μH
671 26980
PE-53112
RL2442
L68
68 μH
671 26990
PE-92114
RL2443
L100
100 μH
671 27000
PE-92108
RL2444
L150
150 μH
671 27010
PE-53113
RL1954
L220
220 μH
671 27020
PE-52626
RL1953
L330
330 μH
671 27030
PE-52627
RL1952
L470
470 μH
671 27040
PE-53114
RL1951
L680
680 μH
671 27050
PE-52629
RL1950
H150
150 μH
671 27060
PE-53115
RL2445
H220
220 μH
671 27070
PE-53116
RL2446
H330
330 μH
671 27080
PE-53117
RL2447
H470
470 μH
671 27090
PE-53118
RL1961
H680
680 μH
671 27100
PE-53119
RL1960
H1000
1000 μH
671 27110
PE-53120
RL1959
H1500
1500 μH
671 27120
PE-53121
RL1958
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
表 8-4. Inductor Selection by Manufacturer's Part Number (continued)
(1)
(2)
(3)
INDUCTOR CODE
INDUCTOR VALUE
SCHOTT(1)
PULSE ENG.(2)
RENCO(3)
H2200
2200 μH
671 27130
PE-53122
RL2448
Schott Corporation, (612) 475-1173, 1000 Parkers Lake Road, Wayzata, MN 55391.
Pulse Engineering, (619) 674-8100, P.O. Box 12235, San Diego, CA 92112.
Renco Electronics Incorporated, (516) 586-5566, 60 Jeffryn Blvd. East, Deer Park, NY 11729.
9 Power Supply Recommendations
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring
inductance generate voltage transients which can cause problems. For minimal inductance and ground loops,
the length of the leads indicated by heavy lines should be kept as short as possible. Single-point grounding (as
indicated) or ground plane construction should be used for best results. When using the adjustable version,
physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring short.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
25
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
10 Layout
10.1 Layout Guidelines
Board layout is critical for the proper operation of switching power supplies. First, the ground plane area must be
sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects
of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of
input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The
magnitude of this noise tends to increase as the output current increases. This noise may turn into
electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, take care in
layout to minimize the effect of this switching noise. The most important layout rule is to keep the AC current
loops as small as possible. 图 10-1 shows the current flow in a buck converter. The top schematic shows a
dotted line which represents the current flow during the top-switch ON-state. The middle schematic shows the
current flow during the top-switch OFF-state. The bottom schematic shows the currents referred to as AC
currents. These AC currents are the most critical because they are changing in a very short time period. The
dotted lines of the bottom schematic are the traces to keep as short and wide as possible. This also yields a
small loop area reducing the loop inductance. To avoid functional problems due to layout, review the PCB layout
example. Best results are achieved if the placement of the LM2576 device, the bypass capacitor, the Schottky
diode, RFBB, RFBT, and the inductor are placed as shown in 图 10-2.TI also recommends using 2-oz copper
boards or heavier to help thermal dissipation and to reduce the parasitic inductances of board traces. See
application note AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines (SNVA054) for more information.
图 10-1. Current Flow in Buck Application
26
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
10.2 Layout Example
图 10-2. LM2576xx Layout Example
10.3 Grounding
To maintain output voltage stability, the power ground connections must be low-impedance (see 图 8-3 and 图
8-9). For the 5-lead TO-220 and DDPAK/TO-263 style package, both the tab and pin 3 are ground and either
connection may be used, as they are both part of the same copper lead frame.
10.4 Heat Sink and Thermal Considerations
In many cases, only a small heat sink is required to keep the LM2576 junction temperature within the allowed
operating range. For each application, to determine whether or not a heat sink is required, the following must be
identified:
1. Maximum ambient temperature (in the application).
2. Maximum regulator power dissipation (in application).
3. Maximum allowed junction temperature (125°C for the LM2576). For a safe, conservative design, a
temperature approximately 15°C cooler than the maximum temperatures must be selected.
4. LM2576 package thermal resistances θJA and θJC.
Total power dissipated by the LM2576 can be estimated in 方程式 10:
PD = (VIN)(IQ) + (VO/VIN)(ILOAD)(VSAT)
(12)
where
• IQ (quiescent current) and VSAT can be found in 节 6.11 shown previously,
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
27
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
• VIN is the applied minimum input voltage, VO is the regulated output voltage,
• and ILOAD is the load current.
The dynamic losses during turnon and turnoff are negligible if a Schottky type catch diode is used.
When no heat sink is used, the junction temperature rise can be determined by 方程式 11:
ΔTJ = (PD) (θJA)
(13)
To arrive at the actual operating junction temperature, add the junction temperature rise to the maximum ambient
temperature.
TJ = ΔTJ + TA
(14)
If the actual operating junction temperature is greater than the selected safe operating junction temperature
determined in step 3, then a heat sink is required.
When using a heat sink, the junction temperature rise can be determined by 方程式 12:
ΔTJ = (PD) (θJC + θinterface + θHeat sink)
(15)
The operating junction temperature is:
TJ = TA + ΔTJ
(16)
As in 方程式 14, if the actual operating junction temperature is greater than the selected safe operating junction
temperature, then a larger heat sink is required (one that has a lower thermal resistance).
28
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
11 Device and Documentation Support
11.1 Device Support
11.1.1 Device Nomenclature
11.1.1.1 Definition of Terms
BUCK REGULATOR
A switching regulator topology in which a higher voltage is converted to a lower voltage.
Also known as a step-down switching regulator.
BUCK-BOOST
REGULATOR
A switching regulator topology in which a positive voltage is converted to a negative
voltage without a transformer.
DUTY CYCLE (D)
Ratio of the output switch's on-time to the oscillator period.
(17)
CATCH DIODE OR
CURRENT
STEERING DIODE
The diode which provides a return path for the load current when the LM2576 switch is
OFF.
EFFICIENCY (η)
The proportion of input power actually delivered to the load.
(18)
CAPACITOR
EQUIVALENT
SERIES
RESISTANCE (ESR)
The purely resistive component of a real capacitor's impedance (see 图 11-1). It causes
power loss resulting in capacitor heating, which directly affects the capacitor's operating
lifetime. When used as a switching regulator output filter, higher ESR values result in
higher output ripple voltages.
图 11-1. Simple Model of a Real Capacitor
Most standard aluminum electrolytic capacitors in the 100 μF–1000 μF range have
0.5Ω to 0.1Ω ESR. Higher-grade capacitors (low-ESR, high-frequency, or lowinductance) in the 100 μF to 1000 μF range generally have ESR of less than 0.15Ω.
EQUIVALENT
SERIES
INDUCTANCE (ESL)
The pure inductance component of a capacitor (see 图 11-1). The amount of inductance
is determined to a large extent on the capacitor's construction. In a buck regulator, this
unwanted inductance causes voltage spikes to appear on the output.
OUTPUT RIPPLE
VOLTAGE
The AC component of the switching regulator's output voltage. It is usually dominated
by the output capacitor's ESR multiplied by the inductor's ripple current (ΔIIND). The
peak-to-peak value of this sawtooth ripple current can be determined by reading 节
8.1.3.
CAPACITOR RIPPLE RMS value of the maximum allowable alternating current at which a capacitor can be
CURRENT
operated continuously at a specified temperature.
STANDBY
QUIESCENT
CURRENT (ISTBY)
Supply current required by the LM2576 when in the standby mode ( ON /OFF pin is
driven to TTL-high voltage, thus turning the output switch OFF).
INDUCTOR RIPPLE
CURRENT (ΔIIND)
The peak-to-peak value of the inductor current waveform, typically a sawtooth
waveform when the regulator is operating in the continuous mode (vs. discontinuous
mode).
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
29
LM2576, LM2576HV
www.ti.com.cn
ZHCSNR6F – JUNE 1999 – REVISED MAY 2021
CONTINUOUS/
DISCONTINUOUS
MODE OPERATION
Relates to the inductor current. In the continuous mode, the inductor current is always
flowing and never drops to zero, vs. the discontinuous mode, where the inductor current
drops to zero for a period of time in the normal switching cycle.
INDUCTOR
SATURATION
The condition which exists when an inductor cannot hold any more magnetic flux. When
an inductor saturates, the inductor appears less inductive and the resistive component
dominates. Inductor current is then limited only by the DC resistance of the wire and the
available source current.
OPERATING VOLT
MICROSECOND
CONSTANT (E•Top)
The product (in VoIt•μs) of the voltage applied to the inductor and the time the voltage
is applied. This E•Top constant is a measure of the energy handling capability of an
inductor and is dependent upon the type of core, the core area, the number of turns,
and the duty cycle.
11.1.2 Custom Design with WEBENCH Tools
Create a Custom Design with WEBENCH Tools
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines (SNVA054)
11.3 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
11.4 接收文档更新通知
要接收文档更新通知,请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册,即可每周接收产品信息更
改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
11.5 Trademarks
TI E2E™ is a trademark of Texas Instruments.
SIMPLE SWITCHER® is a registered trademark of TI.
WEBENCH® is a registered trademark of Texas Instruments.
is a registered trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.7 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com/legal/termsofsale.html) 或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI
提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。重要声明
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021,德州仪器 (TI) 公司
PACKAGE OPTION ADDENDUM
www.ti.com
13-May-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
LM2576HVS-12
NRND
DDPAK/
TO-263
KTT
5
45
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576
HVS-12 P+
LM2576HVS-12/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-12 P+
Samples
LM2576HVS-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-3.3 P+
Samples
LM2576HVS-5.0
NRND
DDPAK/
TO-263
KTT
5
45
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVS-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVS-ADJ
NRND
DDPAK/
TO-263
KTT
5
45
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVS-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVSX-12
NRND
DDPAK/
TO-263
KTT
5
500
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576
HVS-12 P+
LM2576HVSX-12/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-12 P+
Samples
LM2576HVSX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-3.3 P+
Samples
LM2576HVSX-5.0
NRND
DDPAK/
TO-263
KTT
5
500
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVSX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVSX-ADJ
NRND
DDPAK/
TO-263
KTT
5
500
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVSX-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVT-12
NRND
TO-220
KC
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-12 P+
LM2576HVT-12/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576HVT-12/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
Addendum-Page 1
-40 to 125
Samples
Samples
Samples
Samples
LM2576HVT
-12 P+
Samples
LM2576HVT
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
13-May-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
-12 P+
LM2576HVT-15/LB03
NRND
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
LM2576HVT
-15 P+
LM2576HVT-15/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576HVT
-15 P+
Samples
LM2576HVT-15/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-15 P+
Samples
LM2576HVT-5.0
NRND
TO-220
KC
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-5.0 P+
LM2576HVT-5.0/LB03
NRND
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
LM2576HVT
-5.0 P+
LM2576HVT-5.0/LF02
ACTIVE
TO-220
NEB
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576HVT
-5.0 P+
Samples
LM2576HVT-5.0/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576HVT
-5.0 P+
Samples
LM2576HVT-5.0/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-5.0 P+
Samples
LM2576HVT-ADJ
NRND
TO-220
KC
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-ADJ P+
LM2576HVT-ADJ/LB03
NRND
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
LM2576HVT
-ADJ P+
LM2576HVT-ADJ/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576HVT
-ADJ P+
Samples
LM2576HVT-ADJ/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-ADJ P+
Samples
LM2576S-12
NRND
DDPAK/
TO-263
KTT
5
45
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576S
-12 P+
LM2576S-12/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-12 P+
Samples
LM2576S-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-3.3 P+
Samples
LM2576S-5.0
NRND
DDPAK/
TO-263
KTT
5
45
Non-RoHS
& Green
Call TI
Level-3-235C-168 HR
-40 to 125
LM2576S
-5.0 P+
LM2576S-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-5.0 P+
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
13-May-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
LM2576S-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-ADJ P+
Samples
LM2576SX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-3.3 P+
Samples
LM2576SX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-5.0 P+
Samples
LM2576SX-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-ADJ P+
Samples
LM2576T-12
NRND
TO-220
KC
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
-40 to 125
LM2576T
-12 P+
LM2576T-12/LB03
NRND
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
LM2576T
-12 P+
LM2576T-12/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-12 P+
Samples
LM2576T-12/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-12 P+
Samples
LM2576T-15/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-15 P+
Samples
LM2576T-15/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-15 P+
Samples
LM2576T-3.3/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-3.3 P+
Samples
LM2576T-3.3/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
-40 to 125
LM2576T
-3.3 P+
Samples
LM2576T-5.0
NRND
TO-220
KC
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
-40 to 125
LM2576T
-5.0 P+
LM2576T-5.0/LB03
NRND
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
LM2576T
-5.0 P+
LM2576T-5.0/LF02
ACTIVE
TO-220
NEB
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-5.0 P+
Samples
LM2576T-5.0/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-5.0 P+
Samples
LM2576T-5.0/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-5.0 P+
Samples
Addendum-Page 3
-40 to 125
-40 to 125
-40 to 125
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
13-May-2022
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
LM2576T-ADJ
NRND
TO-220
KC
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
-40 to 125
LM2576T-ADJ/LB03
NRND
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
LM2576T
-ADJ P+
LM2576T-ADJ/LF02
ACTIVE
TO-220
NEB
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-ADJ P+
Samples
LM2576T-ADJ/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-ADJ P+
Samples
LM2576T-ADJ/NOPB
ACTIVE
TO-220
KC
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
LM2576T
-ADJ P+
Samples
-40 to 125
LM2576T
-ADJ P+
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of