LM2904LVQDRQ1

LM2902-Q1 QUADRUPLE OPERATIONAL AMPLIFIER SGLS178E − AUGUST 2003 − REVISED APRIL 2008 D Qualified for Automotive Applications D ESD Protection 2 kV Machine Model >200 V and Charge Device Model = 2 kV For K-Suffix Devices. Low Supply-Current Drain Independent of Supply Voltage . . . 0.8 mA Typ Low Input Bias and Offset Parameters: − Input Offset Voltage . . . 3 mV Typ − Input Offset Current . . . 2 nA Typ − Input Bias Current . . . 20 nA Typ D D D Includes Ground, Allowing Direct Sensing Near Ground Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage: − Non-V devices . . . 26 V − V-Suffix devices . . . 32 V Open-Loop Differential Voltage Amplification . . . 100 V/mV Typ Internal Frequency Compensation D OR PW PACKAGE (TOP VIEW) 1OUT 1IN− 1IN+ VCC 2IN+ 2IN− 2OUT description/ordering information 1 14 2 13 3 12 4 11 5 10 4OUT 4IN− 4IN+ GND 3IN+ 3IN− 3OUT This device consists of four independent high-gain 6 9 frequency-compensated operational amplifiers that 7 8 are designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies is possible when the difference between the two supplies is 3 V to 26 V (3 V to 32 V for V-suffixed devices), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational-amplifier circuits that now can be more easily implemented in single-supply-voltage systems. For example, the LM2902 can be operated directly from the standard 5-V supply that is used in digital systems and easily provides the required interface electronics without requiring additional ±15-V supplies. ORDERING INFORMATION{ TA −40°C 40°C to 125°C VIO max AT 25°C MAX VCC 7 mV 26 V 7 mV 2 mV 32 V 32 V PACKAGE‡ ORDERABLE PART NUMBER TOP-SIDE MARKING SOIC (D) Reel of 2500 LM2902QDRQ1 2902Q1 TSSOP (PW) Reel of 2000 LM2902QPWRQ1 2902Q1 SOIC (D) Reel of 2500 LM2902KVQDRQ1 2902KVQ TSSOP (PW) Reel of 2000 LM2902KVQPWRQ1 2902KVQ SOIC (D) Reel of 2500 LM2902KAVQDRQ1 2902KAQ TSSOP (PW) Reel of 2000 LM2902KAVQPWRQ1 2902KAQ † For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at http://www.ti.com. ‡ Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2008 Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 LM2902-Q1 QUADRUPLE OPERATIONAL AMPLIFIER SGLS178E − AUGUST 2003 − REVISED APRIL 2008 symbol (each amplifier) IN− − OUT + IN+ schematic (each amplifier) VCC ≈6-µA Current Regulator ≈6-µA Current Regulator ≈100-µA Current Regulator OUT IN− ≈50-µA Current Regulator IN+ GND To Other Amplifiers COMPONENT COUNT (TOTAL DEVICE) Epi-FET Transistors Diodes Resistors Capacitors 2 POST OFFICE BOX 655303 1 95 4 11 4 • DALLAS, TEXAS 75265 LM2902-Q1 QUADRUPLE OPERATIONAL AMPLIFIER SGLS178E − AUGUST 2003 − REVISED APRIL 2008 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) LM2902-Q1 LM2902KV-Q1 UNIT 26 32 V ± 26 ± 32 V Input voltage, VI (either input) −0.3 to 26 −0.3 to 32 V Duration of output short circuit (one amplifier) to ground at (or below) TA = 25°C, VCC ≤ 15 V (see Note 3) Unlimited Unlimited D package (0 LFPM) 101 101 PW package 113 113 142 142 °C −65 to 150 −65 to 150 °C Differential input voltage, VID (see Note 2) Package thermal impedance, impedance θJA (see Notes 4 and 5) Operating virtual junction temperature, TJ Storage temperature range, Tstg °C/W † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages and VCC specified for the measurement of IOS, are with respect to the network GND. 2. Differential voltages are at IN+ with respect to IN−. 3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. 4. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 142°C can affect reliability. 5. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 LM2902-Q1 QUADRUPLE OPERATIONAL AMPLIFIER SGLS178E − AUGUST 2003 − REVISED APRIL 2008 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) TEST CONDITIONS† PARAMETER VIO Input offset voltage VCC = 5 V to 26 V, VIC = VICRmin, VO = 1.4 V IIO Input offset current VO = 1.4 14V IIB Input bias current VO = 1.4 14V TA‡ LM2902-Q1 MIN 25°C 2 VOL 22 23 Full range Common-mode rejection ratio VIC = VICRmin Supply voltage rejection ratio (∆VCC /∆VIO) Supply-voltage VO1/ VO2 Crosstalk attenuation ICC VCC − 1.5 Full range kSVR Supply current (four amplifiers) 25°C Full range CMRR Short-circuit output current 0 to VCC − 2 RL ≥ 10 kΩ VCC = 15 V, VO = 1 V to 11 V, RL ≥ 2 kΩ IOS Full range RL = 2 kΩ Large-signal differential voltage amplification Output current 0 to VCC − 1.5 VCC = 26 V, AVD IO 25°C f = 1 kHz to 20 kHz VCC = 15 V, VO = 0 VID = 1 V, VCC = 15 V, VO = 15 V VID = −1 V, VID = −1 V, VO = 200 mV V 20 V/mV Full range 15 25°C 50 80 dB 25°C 50 100 dB 120 dB 25°C 25°C −20 Full range −10 25°C 10 Full range 5 −30 −60 mA 20 µA 25°C ±40 ±60 No load Full range 0.7 1.2 VCC = 26 V VO = 0.5 VCC, No load Full range 1.4 3 VO = 2.5 V, † All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. Full range is −40°C to 125°C. § All typical values are at T = 25°C. A ‡ 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 100 30 VO = 0, nA 24 25°C VCC at 5 V, GND at −5 V nA V 5 25°C mV −250 −500 VCC = 26 V, RL ≤ 10 kΩ Low-level output voltage −20 UNIT 50 300 Full range VCC = 5 V to 26 V High-level High level output voltage 7 Full range RL = 10 kΩ VOH 3 10 25°C Common mode input voltage range Common-mode MAX Full range 25°C VICR C TYP § mA mA LM2902-Q1 QUADRUPLE OPERATIONAL AMPLIFIER SGLS178E − AUGUST 2003 − REVISED APRIL 2008 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) (continued) PARAMETER VIO ∆VIO/∆T Input offset voltage Temperature drift IIO Input offset current ∆IIO/∆T Temperature drift IIB VICR C Input bias current Common mode input voltage range Common-mode TA‡ TEST CONDITIONS† Non-A devices VCC = 5 V to 32 V, VIC = VICRmin, VO = 1.4 14V A-suffix devices RS = 0 Ω VO = 1.4 14V 25°C VOL High-level High level output voltage Low-level output voltage 7 25°C 2 10 25°C −20 Full range 25°C 0 to VCC − 1.5 Full range 0 to VCC − 2 25°C VCC − 1.5 RL = 2 kΩ Full range 26 VCC = 32 V, RL ≥ 10 kΩ Full range 27 Full range 25 Full range 15 25°C CMRR Common-mode rejection ratio VIC = VICRmin 25°C kSVR Supply-voltage rejection ratio (∆VCC /∆VIO) 25°C VO1/ VO2 Crosstalk attenuation IOS Short-circuit output current ICC Supply current (four amplifiers) µV/°C 50 nA pA/°C −250 nA V 20 mV 100 V/mV 120 dB 60 80 dB 60 100 dB f = 1 kHz to 20 kHz 25°C VCC = 15 VO = 0 25°C −20 Full range −10 25°C 10 Full range 5 12 VID = 1 V, V mV V 5 25°C f = 1 kHz to 20 kHz, input referred 2 −500 VCC = 32 V, RL ≤ 10 kΩ 7 150 Full range VCC = 5 V to 32 V UNIT 4 Full range Amplifier-to-amplifier coupling¶ Output p current 1 Full range VO = 1.4 14V MAX 10 Full range VCC = 15 V, VO = 1 V to 11 V, RL ≥ 2 kΩ IO 3 25°C Large-signal differential voltage amplification AVD TYP § Full range RL = 10 kΩ VOH LM2902KV-Q1 MIN 120 −30 dB −60 mA 20 VCC = 15 VO = 15 V VID = −1 1 V, V VID = −1 V, VO = 200 mV 25°C VCC at 5 V, GND at −5 V VO = 0, 25°C ±40 ±60 VO = 2.5 V, No load Full range 0.7 1.2 VCC = 32 V VO = 0.5 VCC, No load Full range 1.4 3 µA 40 mA mA † All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. Full range is −40°C to 125°C. § All typical values are at T = 25°C. A ¶ Due to proximity of external components, ensure that coupling is not originating via stray capacitance between these external parts. Typically, this can be detected, as this type of coupling increases at higher frequencies. ‡ POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 LM2902-Q1 QUADRUPLE OPERATIONAL AMPLIFIER SGLS178E − AUGUST 2003 − REVISED APRIL 2008 operating conditions, VCC = ±15 V, TA = 25°C PARAMETER TEST CONDITIONS TYP UNIT 0.5 V/µs SR Slew rate at unity gain RL = 1 MΩ, CL = 30 pF, VI = ±10 V (see Figure 1) B1 Unity-gain bandwidth RL = 1 MΩ, CL = 20 pF (see Figure 1) 1.2 MHz Vn Equivalent input noise voltage RS = 100 Ω, VI = 0 V, f = 1 kHz (see Figure 2) 35 nV/√Hz VCC+ − VI VO + VCC− CL RL Figure 1. Unity-Gain Amplifier 900 Ω VCC+ 100 Ω − VI = 0 V RS VO + VCC− Figure 2. Noise-Test Circuit 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) LM2902KAVQDRQ1 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902KAQ LM2902KAVQPWRG4Q1 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902KAQ LM2902KAVQPWRQ1 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902KAQ LM2902KVQDRQ1 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902KVQ LM2902KVQPWRG4Q1 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902KVQ LM2902KVQPWRQ1 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902KVQ LM2902QDRG4Q1 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902Q1 LM2902QDRQ1 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902Q1 LM2902QPWRG4Q1 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902Q1 LM2902QPWRQ1 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 2902Q1 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of