0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LM3410XSDLEDEV/NOPB

LM3410XSDLEDEV/NOPB

  • 厂商:

    BURR-BROWN(德州仪器)

  • 封装:

    -

  • 描述:

    BOARD DEMO FOR LM3410X

  • 数据手册
  • 价格&库存
LM3410XSDLEDEV/NOPB 数据手册
User's Guide SNVA314B – January 2008 – Revised May 2013 AN-1774 LM3410X LED Driver 6-Pin LLP Demo Board 1 Introduction The demo board included in this shipment converts 2.7V to 5.5V input, and illuminates four 50mA LED’s in series using the LM3410X 1.6MHz LED driver switching converter. This is a 2-layer board using the bottom layer as a Ground plane. A bill of materials (see Section 2) describes the parts used on this demo board. A schematic and layout have also been included below along with measured performance characteristics. The above restrictions for the input voltage are valid only for the demo board as shipped with the demo board schematic below. Operatiing Conditions VIN = 2.7V to 5.5V VO ≊ VF x 4 + VFB ≊ 3.6V x 4 + 0.198V ≊ 14.4V IO = 50mA L1 D1 VIN LM3410 C1 R2 DIMM 1 6 2 5 3 4 LEDs C2 R1 Figure 1. LM3410X 6-Pin LLP Schematic All trademarks are the property of their respective owners. SNVA314B – January 2008 – Revised May 2013 Submit Documentation Feedback AN-1774 LM3410X LED Driver 6-Pin LLP Demo Board Copyright © 2008–2013, Texas Instruments Incorporated 1 Bill of Materials LM3410X www.ti.com PGND 1 6 SW VIN 2 5 AGND DIM 3 4 FB Figure 2. Pinout Table 1. Pin Descriptions - 6 Pin LLP 2 2 Pin Name Function 1 PGND Power ground pin. Place PGND and output capacitor GND close together. 2 VIN Supply voltage for power stage, and input supply voltage. 3 DIM Dimming & shutdown control input. Logic high enables operation. Duty Cycle from 0 to 100%. Do not allow this pin to float or be greater than VIN + 0.3V. 4 FB Feedback pin. Connect FB to external resistor divider to set output voltage. 5 AGND 6 SW DAP GND Signal ground pin. Place the bottom resistor of the feedback network as close as possible to this pin & pin 4. Output switch. Connect to the inductor, output diode. Signal & Power ground. Connect to pin 1 & pin 5 on top layer. Place 4-6 vias from DAP to bottom layer GND plane. Bill of Materials LM3410X Part ID Part Value Manufacturer Part Number U1 2.8A ISW LED Driver NSC LM3410XSD C1, Input Cap 10µF, 6.3V, X5R TDK C2012X5R0J106M C2 Output Cap 2.2µF, 25V, X5R TDK C2012X5R1E225M D1, Catch Diode 0.4Vf Schottky 500mA, 30VR Diodes Inc MBR0530 L1 10µH 1.5A Coilcraft DO1608C-103 R1 4.02Ω, 1% Vishay CRCW08054R02F R2 100kΩ, 1% Vishay CRCW06031003F LED’s SMD-1206, 50mA, Vf ≊ 3 .6V Lite-On LTW-150k AN-1774 LM3410X LED Driver 6-Pin LLP Demo Board SNVA314B – January 2008 – Revised May 2013 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Performance Characteristics www.ti.com 3 Performance Characteristics Figure 3. LM3410X Efficiency vs Input Voltage Series LEDs @ 50mA 4 Figure 4. LM3410X Average LED Current vs DutyCycle & Dimming Frequency PCB Layout Figure 5. Demonstration Board Top Layer SNVA314B – January 2008 – Revised May 2013 Submit Documentation Feedback AN-1774 LM3410X LED Driver 6-Pin LLP Demo Board Copyright © 2008–2013, Texas Instruments Incorporated 3 16V > VPWR > 5.5V Application Circuit www.ti.com Figure 6. Demonstration Board Bottom Layer 5 16V > VPWR > 5.5V Application Circuit The demonstration board provided can easily be modified to allow the user to derive the power from an input supply that is larger than 5.5V. In Figure 7 two separate supplies are needed. VIN must be between 2.7V minimum to 5.5V maximum, but VPWR can be as great as 16V. L1 D1 VPWR C1 R2 LM3410 R3 DIMM D2 1 6 2 5 3 4 LEDs C2 C3 R1 Figure 7. Circuit Needs Two Separate Supplies The circuit shown in Figure 8 allows for a single supply to be used with a simple zenner diode regulation circuit to provide the LM3410 with a housekeeping and driver voltage that is below 5.5V. 4 AN-1774 LM3410X LED Driver 6-Pin LLP Demo Board SNVA314B – January 2008 – Revised May 2013 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated 16V > VPWR > 5.5V Application Circuit www.ti.com L1 D1 VPWR C1 LM3410 VIN R2 C3 1 6 2 5 3 4 LEDs C2 DIMM R1 Figure 8. Circuit Allows Single Supply The LM3410 VIN supply will draw approximately 7 mA while it is switching. Zenner diode should have a breakdown voltage lower than 5V, and size R3 to allow for 7 mA of current draw. Table 2. List of Components Part ID Part Value Manufacturer Part Number U1 2.8A ISW LED Driver NSC LM3410XSD C1 VPWR Input Cap 10µF, 6.3V, X5R TDK C1608X5R0J106K C2 Output Cap 1µF, 25V, X5R TDK C2012X5R1E105K C3 VIN Input Cap 0.1µF,16V, X5R TDK C1005X5R1C104K D1, Catch Diode 0.43Vf, Schotky, 0.5A, 30VR Diodes Inc B0530W L1 6.8µH 2.7A Coilcraft MOS6020-682 R1 4.02Ω, 1% Vishay CRCW08054R02FRT1 R2 100kΩ, 1% Vishay CRCW08051003F R3 576Ω, 1% Vishay CRCW08055760F D2 3.3V Zener, SOT23 Diodes Inc BZX84C3V3 LEDs SMD-1206, 50mA, Vf ≊ 3 .6V SNVA314B – January 2008 – Revised May 2013 Submit Documentation Feedback AN-1774 LM3410X LED Driver 6-Pin LLP Demo Board Copyright © 2008–2013, Texas Instruments Incorporated 5 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated
LM3410XSDLEDEV/NOPB 价格&库存

很抱歉,暂时无法提供与“LM3410XSDLEDEV/NOPB”相匹配的价格&库存,您可以联系我们找货

免费人工找货