Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
LM98722 3 Channel, 16-Bit, 45 MSPS Analog Front End with LVDS/CMOS Output,
Integrated CCD/CIS Sensor Timing Generator, and Spread Spectrum Clock Generation
1 Features
3 Description
•
•
The LM98722 is a fully integrated, high performance
16-Bit, 45 MSPS signal processing solution for digital
color copiers, scanners, and other image processing
applications. High-speed signal throughput is
achieved with an innovative architecture utilizing
Correlated Double Sampling (CDS), typically
employed with CCD arrays, or Sample and Hold
(S/H) inputs (for higher speed CCD or CMOS image
sensors). The signal paths utilize 8 bit Programmable
Gain Amplifiers (PGA), a +/-9-Bit offset correction
DAC and independently controlled Digital Black Level
correction loops for each input. The PGA and offset
DAC are programmed independently allowing unique
values of gain and offset for each of the three analog
inputs. The signals are then routed to a 45-MHz high
performance analog-to-digital converter (ADC). The
fully
differential
processing
channel
shows
exceptional noise immunity, having a very low noise
floor of -74dB. The 16-bit ADC has excellent dynamic
performance making the LM98722 transparent in the
image reproduction chain.
1
•
•
•
•
•
•
LVDS/CMOS Outputs
LVDS/CMOS/Crystal Clock Source with PLL
Multiplication
Integrated Flexible Spread Spectrum Clock
Generation
CDS or S/H Processing for CCD or CIS sensors
Independent Gain/Offset Correction for Each
Channel
Automatic per-Channel Gain and Offset
Calibration
Programmable Input Clamp Voltage
Flexible CCD/CIS Sensor Timing Generator
2 Applications
•
•
•
•
•
Multi-Function Peripherals
High-speed Currency/Check Scanners
Flatbed or Handheld Color Scanners
High-speed Document Scanners
Key Specifications:
– Maximum Input Level:
– 1.2-V or 2.4-V Modes (Both with + or Polarity Option)
– ADC Resolution: 16-Bit
– ADC Sampling Rate: 45 MSPS
– INL: +18/-25 LSB (typ)
– Channel Sampling Rate: 22.5/22.5/15 MSPS
(1ch/2ch/3ch)
– PGA Gain Steps: 256 Steps
– PGA Gain Range: 0.64 to 8.3x
– Analog DAC Resolution: +/-9 Bits
– Analog DAC Range: +/-307 mV or +/-614 mV
– Digital DAC Resolution: +/-6 Bits
– Digital DAC Range: -2048 LSB to + 2016 LSB
– SNR: -74dB (at 0dB PGA Gain)
– Power Dissipation: 630 mW (LVDS)
– Operating Temp: 0 to 70°C
– Supply Voltage: 3.3-V Nominal (3.0-V to 3.6-V
Range)
A very flexible integrated Spread Spectrum Clock
Generation (SSCG) modulator is included to assist
with EM compliance and reduce system costs.
Device Information
ORDER NUMBER
LM98722
PACKAGE
TSSOP (56)
BODY SIZE
14.0 mm x 6.10 mm
Simplified Schematic
CCD/CIS Sensor
Analog Front End
SPI
LM98722
Sensor Drivers
CCD Timing
Generator
Data Output
CLK
SSCG
Image Processor/
ASIC
Motor
Controllers
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
7
1
1
1
2
3
6
Absolute Maximum Ratings ...................................... 6
ESD Ratings.............................................................. 6
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 7
Electrical Characteristics........................................... 7
AC Timing Requirements........................................ 11
Detailed Description ............................................ 13
7.1
7.2
7.3
7.4
7.5
Overview .................................................................
Functional Block Diagrams .....................................
Feature Description.................................................
Device Functional Modes........................................
Registers Maps .......................................................
13
14
16
25
91
8
Layout ................................................................. 141
9
Device and Documentation Support................ 142
8.1 Layout Example .................................................... 141
9.1
9.2
9.3
9.4
Device Support......................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
142
142
142
142
10 Mechanical, Packaging, and Orderable
Information ......................................................... 142
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (April 2013) to Revision B
Page
•
Added, updated, or revised the following sections in accordance with new datasheet standards: Description; Pin
Configuration and Functions; Specifications; Detailed Description; Application and Implementation; Device and
Documentation Support; and Mechanical, Packaging, and Ordering Information.................................................................. 1
•
Changed "29" to "33" for Pin 32 INCLK+ in Pin Functions table............................................................................................ 4
•
Deleted "Boldface limits apply..." statement in Electrical Characteristics and AC Timing Requirements ............................. 7
•
Changed "external" to "internal" and changed "internal" to "external" under "SH_R Capture Clock Select (Page 0,
Register 0x00, Bit 5)" bullet point in Clock Sources - Additional Settings and Flexibility..................................................... 19
•
Changed 25 MHz to 15 MHz in Table 4 .............................................................................................................................. 26
•
Changed 50 MHz to 45 MHz in Table 4 ............................................................................................................................... 26
•
Changed "Page 2" to "Page 0" in CCD Timing Generator Master/Slave Modes and Master Timing Generator Mode....... 64
•
Added "Note" to Serial Interface .......................................................................................................................................... 86
•
Changed "1100 0000" to "1100 0010" for Page 0, Addr 2 ................................................................................................ 104
Changes from Original (April 2013) to Revision A
•
2
Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 1
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
5 Pin Configuration and Functions
56-Pin TSSOP
Package DGG056A
(Top View)
PHIC2
1
56
SH5
PHIC1
2
55
SH4
SH1
3
54
PHIB2
CE
4
53
PHIB1
CAL
5
52
VC
RESET
6
51
DGND
SH_R
7
50
PHIA2
SDI
8
49
PHIA1
SDO
9
48
CP
SCLK
10
47
RS
SEN
11
46
SH3
VA
12
45
CLKOUT/SH2
AGND
13
44
VC
VA
14
VREFB
56 Pin TSSOP
(not to scale)
43
VD
15
42
DGND
VREFT
16
41
DOUT0/TXOUT0-
VA
17
40
DOUT1/TXOUT0+
AGND
18
39
DOUT2/TXOUT1-
VCLP
19
38
DOUT3/TXOUT1+
VA
20
37
DOUT4/TXOUT2-
IBIAS
21
36
DOUT5/TXOUT2+
AGND
22
35
DOUT6/TXCLK-
OSR
23
34
DOUT7/TXCLK+
AGND
24
33
INCLK-
OSG
25
32
INCLK+
AGND
26
31
DVB
OSB
27
30
CPOFILT1
CPOFILT2
28
29
DGND
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
3
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Pin Descriptions (1)
PIN
NO.
NAME
I/O
TYP
RES
DESCRIPTION
1
PHIC2
O
D
PU
Configurable high speed sensor timing output.
2
PHIC1
O
D
PD
Configurable high speed sensor timing output.
3
SH1
O
D
PU
Configurable low speed sensor timing output.
Chip Serial Interface Address Setting Input
4
CE
I
D
CE LEVEL
ADDRESS
VD
01
Float
10
DGND
00
5
CAL
I
D
PD
Initiate calibration sequence. Leave unconnected or tie to DGND if unused.
6
RESET
I
D
PU
Active-low master reset. NC when function not being used.
7
SH_R
I
D
PD
External request for an SH interval.
8
SDI
I
D
PD
Serial Interface Data Input.
9
SDO
O
D
10
SCLK
I
D
PD
Serial Interface shift register clock.
11
SEN
I
D
PU
Active-low chip enable for the Serial Interface.
12
VA
P
Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.
13
AGND
P
Analog ground return.
14
VA
P
Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.
15
VREFB
O
A
Bottom of ADC reference. Bypass with a 0.1μF capacitor to ground.
16
VREFT
O
A
Top of ADC reference. Bypass with a 0.1μF capacitor to ground.
17
VA
P
Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.
18
AGND
P
Analog ground return.
19
VCLP
A
Input Clamp Voltage. Normally bypassed with a 0.1μF , and a 4.7μF capacitor to
AGND. An external reference voltage may be applied to this pin.
20
VA
P
Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.
21
IBIAS
A
Bias setting pin. Connect a 9.0 kΩ 1% resistor to AGND.
22
AGND
P
Analog ground return.
23
OSR
A
Analog input signal. Typically sensor Red output AC-coupled thru a capacitor.
24
AGND
P
Analog ground return.
25
OSG
A
Analog input signal. Typically sensor Green output AC-coupled thru a capacitor.
26
AGND
P
Analog ground return.
27
OSB
A
Analog input signal. Typically sensor Blue output AC-coupled thru a capacitor.
28
CPOFILT2
A
Charge Pump Filter Capacitor. Bypass this supply pin with a 0.1μF capacitor to
CPOFILT1.
29
DGND
P
Digital ground return.
30
CPOFILT1
A
Charge Pump Filter Capacitor. Bypass this supply pin with a 0.1μF capacitor to
CPOFILT2.
31
DVB
O
D
Digital Core Voltage bypass. Not an input. Bypass with 0.1μF capacitor to DGND.
32
INCLK+
I
D
Clock Input. Non-Inverting input for LVDS clocks or CMOS clock input. CMOS clock is
selected when pin 33 is held at DGND, otherwise clock is configured for LVDS
operation.
33
INCLK-
I
D
Clock Input. Inverting input for LVDS clocks, connect to DGND for CMOS clock.
O
D
Bit 7 of the digital video output bus in CMOS Mode, LVDS Frame Clock+ in LVDS
Mode.
O
D
Bit 6 of the digital video output bus in CMOS Mode, LVDS Frame Clock- in LVDS
Mode.
34
35
(1)
4
DOUT7/
TXCLK+
DOUT6/
TXCLK-
IO
O
I
I
I
Serial Interface Data Output.
(I=Input), (O=Output), (IO=Bi-directional), (P=Power), (D=Digital), (A=Analog), (PU=Pull Up with an internal resistor), (PD=Pull Down
with an internal resistor.).
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Pin Descriptions(1) (continued)
PIN
NO.
36
37
38
39
40
41
NAME
DOUT5/
TXOUT2+
DOUT4/
TXOUT2DOUT3/
TXOUT1+
DOUT2/
TXOUT1DOUT1/
TXOUT0+
DOUT0/
TXOUT0-
I/O
TYP
O
D
O
D
O
D
O
D
O
D
O
D
O
D
RES
DESCRIPTION
Bit 5 of the digital video output bus in CMOS Mode, LVDS Data Out2+ in LVDS
Mode.
Bit 4 of the digital video output bus in CMOS Mode, LVDS Data Out2- in LVDS Mode.
Bit 3 of the digital video output bus in CMOS Mode, LVDS Data Out1+ in LVDS
Mode.
Bit 2 of the digital video output bus in CMOS Mode, LVDS Data Out1- in LVDS Mode.
Bit 1 of the digital video output bus in CMOS Mode, LVDS Data Out0+ in LVDS
Mode.
Bit 0 of the digital video output bus in CMOS Mode, LVDS Data Out0- in LVDS Mode.
42
DGND
PD
Configurable sensor control output.
43
VD
P
Power supply for the digital circuits. Bypass this supply pin with 0.1μF capacitor. A
single 4.7μF capacitor should be used between the supply and the VD, VR and VC
pins.
44
VC
P
Power supply for the sensor control outputs. Bypass this supply pin with 0.1μF
capacitor.
45
CLKOUT/SH2
O
D
Output clock for registering output data when using CMOS outputs, or a configurable
low speed sensor timing output.
46
SH3
O
D
Configurable low speed sensor timing output.
47
RS
O
D
Configurable high speed sensor timing output.
48
CP
O
D
Configurable high speed sensor timing output.
49
PHIA1
O
D
Configurable high speed sensor timing output.
50
PHIA2
O
D
Configurable high speed sensor timing output.
51
DGND
P
Digital ground return.
52
VC
P
Power supply for the sensor control outputs.
Bypass this supply pin with 0.1μF capacitor.
53
PHIB1
O
D
Configurable high speed sensor timing output.
54
PHIB2
O
D
Configurable high speed sensor timing output.
55
SH4
O
D
Configurable low speed sensor timing output.
56
SH5
O
D
Configurable low speed sensor timing output.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
5
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings (1) (2) (3) (4)
MIN
Supply Voltage (VA, VR, VD, VC)
MAX
UNIT
4.2
V
Voltage on Any Input Pin (not to exceed 4.2 V)
−0.3
VA + 0.3
V
Voltage on Any Output Pin (except DVB and not to exceed 4.2 V)
−0.3
VA + 0.3
V
DVB Output Pin Voltage
2.0
V
Input Current at any pin other than Supply Pins (5)
±25
mA
Package Input Current (except Supply Pins) (5)
±50
mA
Maximum Junction Temperature (TA)
150
°C
Package Dissipation at TA = 25°C (6)
>1.89
W
+150
°C
Storage Temperature, Tstg
(1)
(2)
(3)
(4)
(5)
(6)
–65
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions. Operation of the device beyond the Operating Ratings is not
recommended.
All voltages are measured with respect to AGND = DGND = 0V, unless otherwise specified.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Soldering process must comply with Texas Instrument’s Reflow Temperature Profile specifications. Refer to www.ti.com/packaging
Reflow temperature profiles are different for lead-free and non-lead-free packages.
When the input voltage (VIN) at any pin exceeds the power supplies (VIN < GND or VIN > VA or VD), the current at that pin should be
limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can simultaneously safely exceed the
power supplies with an input current of 25 mA to two.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX,RθJA and the ambient temperature,
TA. The maximum allowable power dissipation at any temperature is PD = (TJMAX – TA)/RθJA. The values for maximum power dissipation
listed above will be reached only when the device is operated in a severe fault condition, (for example, when input or output pins are
driven beyond the power supply voltages, or the power supply polarity is reversed). Such conditions should always be avoided.
6.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
V(ESD)
(1)
(2)
(3)
Electrostatic discharge (1)
(2)
UNIT
±2500
Charged-device model (CDM), per JEDEC specification JESD22C101 (3)
±250
V
Human body model is 100 pF capacitor discharged through a 1.5-kΩ resistor. Machine model is 220 pF discharged through 0 Ω.
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions. Pins listed as ±2500 V may actually have higher performance.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions. Pins listed as ±250 V may actually have higher performance.
6.3 Recommended Operating Conditions (1) (2)
over operating free-air temperature range (unless otherwise noted)
MIN
Operating Temperature Range
All Supply Voltage
(1)
(2)
6
+3.0
MAX
UNIT
0 ≤ TA ≤ +70
°C
+3.6
V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions. Operation of the device beyond the Operating Ratings is not
recommended.
All voltages are measured with respect to AGND = DGND = 0V, unless otherwise specified.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
6.4 Thermal Information
TSSOP
THERMAL METRIC (1)
RθJA
(1)
UNIT
56 TERMINALS
Junction-to-ambient thermal resistance
B-G-R-B-G-R-B-G-R→
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
25
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.2 Mode 2 - Two Channel Input/Synchronous Pixel Sampling
Mode 2 is useful for CCD sensors with a Black and White line with Even and Odd pixels. In its default
configuration, Mode 2 samples Even sensor pixels via the Blue Channel Input, and Odd sensor pixels via the
Green Channel Input. The selection of Even/Odd inputs can be changed through the serial interface registers.
Sampling of the Even and Odd inputs is performed synchronously.
Black
Level
Offset
DAC
COLOR1DAC[9:0]
OSR
CDS
or
Sample/Hold
Amplifier
Input Bias/
Clamping
Black
Level
Offset
DAC
COLOR2DAC[9:0]
OSG
Input Bias/
Clamping
PGA
COLOR2PGA[7:0]
CDS
or
Sample/Hold
Amplifier
Input Bias/
Clamping
Black
Level
Offset
DAC
COLOR3DAC[9:0]
OSB
COLOR1PGA[7:0]
PGA
3:1
MUX
COLOR3PGA[7:0]
CDS
or
Sample/Hold
Amplifier
PGA
Figure 4. Mode 2 Signal Routing
Table 4. Mode 2 Operating Details
DETAIL
OSG and OSB (Default)
Two inputs synchronously
processed as Even and Odd
Pixels. Channel inputs are
configurable.
or
Channels Active
OSR and OSG
or
OSB and OSR
Channel Sample Rate
22.5
ADC Sample Rate
fADC: fINCLK
Output Sequencing
26
MSPS per Channel (max)
45
MSPS (max)
Internal 2x Clock Selected
2:1
fINCLK = 15 MHz (max)
Internal 1x Clock Selected
1:1
fINCLK = 45 MHz (max)
SH Signal --> Even-Odd-Even-Odd-Even-Odd-Even→
or
SH Signal --> Odd-Even-Odd-Even-Odd-Even-Odd→
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.3 Mode 1 - One Channel Input
In Mode 1a, all pixels are processed through a single input (OSR, OSG, or OSB) chosen through the control
register setup. This mode is useful in applications where only one input channel is used. The selected input is
programmable through the control register. In this mode, the maximum channel speed is 22.5MSPS per channel
with the ADC running at 22.5MSPS.
Black
Level
Offset
DAC
COLOR1DAC[9:0]
OSR
Input Bias/
Clamping
CDS
or
Sample/Hold
Amplifier
Black
Level
Offset
DAC
COLOR2DAC[9:0]
OSG
Input Bias/
Clamping
Input Bias/
Clamping
PGA
COLOR2PGA[7:0]
CDS
or
Sample/Hold
Amplifier
Black
Level
Offset
DAC
COLOR3DAC[9:0]
OSB
COLOR1PGA[7:0]
PGA
3:1
MUX
COLOR3PGA[7:0]
CDS
or
Sample/Hold
Amplifier
PGA
Figure 5. Mode 1a Signal Routing
Table 5. Mode 1 Operating Details
DETAIL
Channels Active
OSR or OSG or OSB
Channel Sample Rate
ADC Sample Rate
fADC: fINCLK
Output Sequencing
One color active for all lines.
22.5
MSPS per Channel (max)
22.5
MSPS (max)
1:1
fINCLK = 25MHz (max)
Internal 1x Clock Selected
SH Signal → Color 1→Color 1→Color 1→Color 1→Color 1→
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
27
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 6. Modes of Operation Register Settings Table
OPERATING
MODE
SAMPLING
INPUT(S)
Mode3-RGB
Forward
OSR||OSG||OSB
Mode3-RGB
Reverse
OSR||OSG||OSB
SIGNAL
PATH(S)
RGB
RGB
OUTPUT SEQUENCING MODE 3 and 2 = PIXEL SEQ
PixelR→PixelG→PixelB→
PixelB→PixelG→PixelR→
Mode2-RG Forw.
OSR||OSG
RG
PixelR→PixelG→
Mode2-RG Rev.
OSR||OSG
RG
PixelG→PixelR→
Mode2-GB Forw.
OSG||OSB
GB
PixelG→PixelB→
Mode2-GB Rev.
OSG||OSB
GB
PixelB→PixelG→
Mode2-RB Forw.
OSR||OSB
RB
PixelR→PixelB→
Mode2-RB Rev.
OSR||OSB
RB
PixelB→PixelR
Mode1-R Mono
OSR
R
Color Line Seq: R→R→R→R→
Mode1-G Mono
OSG
G
Color Line Seq: G→G→G→G→
Mode1-B Mono
OSB
B
Color Line Seq: B→B→B→B→
Mode 1 or 2 or 3
Any
CISa
2, 3, or 4 lines in sequence
Gain and Offset are channel specific.
LM98714 style CB bits indicate channel used to process data. Additional CB
bits can be used to identify current line in sequence.
CISb
Mode 1 or 2 or 3
Any
2 or 3 lines in sequence
Gain and Offset for all channels are common, and change from line to line
based on current color in sequence.
LM98714 style CB bits indicate channel used to process data. Additional CB
bits can be used to identify current line in sequence.
28
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.4 Input Bias and Clamping
VA
Input Bias Enable
Configuration 3, Bit[6]
VBIAS
SAMPLE
20kΩ
OSR or
OSG or
OSB
20kΩ
Source Follower Enable
Configuration 3, Bit[7]
CS
Auto CLPIN Enable
Configuration 4, Bit[5]
SAMPLE
CLPIN
AGND
HOLD
VA
CLPIN Gating Enable
Configuration 4, Bit[4]
VBIAS
CLAMP
VCLP
CS
VCLP
VCLP Reference Select
Configuration 4, Bits[3:0]
Sampling Mode Select
(CDS or Sample/Hold Mode)
Configuration 2, Bit[1]
Pixel rate switches to sample OS signal and reference voltages .
Optional line rate switch to clamp OS input to VCLP node .
Static switches controlled by Configuration Registers
SAMPLE, CLAMP, HOLD, CLPIN are internally generated timing signals .
Figure 6. Input Bias and Clamping Diagram
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
29
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.4.1 Input Bias and Clamping - AC Coupled Applications
The inputs to the LM98722 are typically AC coupled through a film capacitor and can be sampled in either
Sample and Hold Mode (S/ H Mode) or Correlated Double Sampling Mode (CDS Mode). In either mode, the DC
bias point for the LM98722 side of the AC coupling capacitor is set using the circuit of Figure 6 which can be
configured to operate in a variety of different modes. A typical CCD waveform is shown in Figure 7. Also shown
in Figure 7 is an internal signal “SAMPLE” which can be used to “gate” the CLPIN signal so that it only occurs
during the “signal” portion of the CCD pixel waveform.
SH
Dummy Pixels
Optical Black Pixels
Invalid
Pixels
Valid Pixels
OSX
Auto CLPIN Start Register
Page 2, Reg. 6, Bits[7:0]
Auto CLPIN End Register
Page 2, Reg. 7, Bits[7:0]
CLPIN
SAMPLE
CLPINGATED
Figure 7. Typical CCD Waveform and LM98722 Input Clamp Signal (CLPIN)
30
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.5 Sample/Hold Mode
SAMPLE
OSR or
OSG or
OSB
CPAR
CS
HOLD
CLAMP
VCLP
CPAR
CS
Figure 8. Sample and Hold Mode Simplified Input Diagram
Proper DC biasing of the CCD waveform in Sample and Hold mode is critical for realizing optimal operating
conditions. In Sample/ Hold mode, the Signal Level of the CCD waveform is compared to the DC voltage on the
VCLP pin. In order to fully utilize the range of the input circuitry, it is desirable to cause the Black Level signal
voltage to be as close to the VCLP voltage as possible, resulting in a near zero scale output for Black Level
pixels.
In Sample/Hold Mode, the DC bias point of the input pin is typically set by actuating the input clamp switch (see
Figure 8) during optical black pixels which connects the input pins to the VCLP pin DC voltage. The signal
controlling this switch is an auto-generated pulse, CLPIN. CLPIN is generated with a programmable pixel delay
with respect to the SH Interval and a programmable # of pixels Duration. These parameters are available through
the serial interface control registers.
Actuating the input clamp will force the average value of the CCD waveform to be centered around the VCLP DC
voltage. During Optical Black Pixels, the CCD output has roughly three components. The first component of the
pixel is a “Reset Noise” peak followed by the Reset (or Pedestal) Level voltage, then finally the Black Level
voltage signal. Taking the average of these signal components will result in a final “clamped” DC bias point that
is close to the Black Level signal voltage.
To provide a more precise DC bias point (that is, a voltage closer to the Black Level voltage), the CLPIN pulse
can be “gated” by the internally generated SAMPLE clock. This resulting CLPINGATED signal is the logical
“AND” of the SAMPLE and CLPIN signals as shown in Figure 7. By using the CLPINGATED signal, the higher
Reset Noise peak will not be included in the clamping period and only the average of the Reset Level and Black
Level components of the CCD waveform will be centered around VCLP.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
31
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.6 DC Coupled Applications
In some applications, particularly with CIS sensors, the output voltage is within a voltage range that will allow DC
coupling of the signal. When using Sample/Hold mode, DC coupling eliminates any problems with signal droop
across the line caused by voltage changes across the coupling capacitor. When DC coupling, the Auto CLPIN
should be disabled.
There are two ways of setting the proper DC levels in this type of application. If the sensor has a Vref output pin,
this can be connected to the VCLP pin of the LM98722. The internal VCLP generation should be disabled to
allow this external reference to set the Black Level for the chip close to the black pixel level of the sensor.
Many CIS sensors will not have a Vref output. In these applications, the internal VCLP voltage of the LM98722
can be set to the level that is closest to the black pixel level of the sensor.
OSR or
OSG or
OSB
fPIXEL
CSH
VCLP
Figure 9. Equivalent Input Switched Capacitance S/H Mode
In Sample and Hold Mode, the impedance of the analog input pins is dominated by the switched capacitance of
the CDS/Sample and Hold amplifier. The amplifier switched capacitance, shown as CS in Figure 8, and internal
parasitic capacitances can be estimated by a single capacitor switched between the analog input and the VCLP
reference pin for Sample and Hold mode. During each pixel cycle, the modeled capacitor, CSH, is charged to the
OSX-VCLP voltage then discharged. The average input current at the OSX pin can be calculated knowing the
input signal amplitude and the frequency of the pixel. If the application requires AC coupling of the CCD output to
the LM98722 analog inputs, the Sample and Hold Mode input bias current may degrade the DC bias point of the
coupling capacitor. To overcome this, Input Source Follower Buffers are available to isolate the larger Sample
and Hold Mode input bias currents from the analog input pin (as discussed in Input Source Follower Buffers). As
shown in CDS Mode section, the input bias current is much lower for CDS mode, eliminating the need for the
source follower buffers.
7.4.7 Input Source Follower Buffers
The OSR, OSG, OSB inputs each have an optional Source Follower Buffer which can be selected with Main
Configuration Register 3 at Page 0, Register 3, Bit[7]. These source followers provide a much higher impedance
seen at the inputs. In some configurations, such as Sample and Hold Mode with AC coupled inputs, the DC bias
point of the input nodes must remain as constant as possible over the entire length of the line to ensure a
uniform comparison to reference level (VCLP in this case). The Source Followers effectively isolate the AC input
coupling capacitor from the switched capacitor network internal to the LM98722’s Sample and Hold/ CDS
Amplifier. This results in a greatly reduced charge loss or gain on the AC Input coupling capacitor over the length
of a line, thereby preserving its DC bias point.
The Source Followers should only be used in the 1.2 V input range (i.e. Gain Mode Register at Page 1, Register
0, Bit[0] = 1, CDS Gain = 2x). Using the Source Followers in the 2.4 V (that is, Gain Mode Register at Page 1,
Register 0, Bit[0] = 0, CDS Gain = 1x). Input range will result in a loss of performance (mainly linearity
performance at the high and low ends of the input range).
32
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.8 CDS Mode
SAMPLE
OSR or
OSG or
OSB
CPAR
CS
HOLD
CLAMP
CPAR
CS
Figure 10. CDS Mode Simplified Input Diagram
Correlated Double Sampling mode does not require as precise a DC bias point as does Sample and Hold mode.
This is due mainly to the nature of CDS itself, that is, the Video Signal voltage is referenced to the Reset Level
voltage instead of the static DC VCLP voltage. The common mode voltage of these two points on the CCD
waveform have little bearing on the resulting differential result. However, the DC bias point does need to be
established to ensure the CCD waveform’s common mode voltage is within rated operating ranges.
The CDS mode biasing can be performed in the same way as described in Sample/Hold Mode, or, an alternative
method is available which precludes the need for a CLPIN pulse. Internal resistor dividers can be switched in
across the OSR, OSG, and/or OSB inputs to provide the DC bias voltage.
SAMPLE
OSR or
OSG or
OSB
IBIAS
CPAR
CS
HOLD
CLAMP
CPAR
CS
Figure 11. CDS Mode Input Bias Current
Unlike in Sample and Hold Mode, the input bias current in CDS Mode is relatively small. Due to the architecture
of CDS switching, the average charge loss or gain on the input node is ideally zero over the duration of a pixel.
This results in a much lower input bias current, whose main source is parasitic impedances and leakage
currents.
As a result of the lower input bias current in CDS Mode, maintaining the DC Bias point the input node over the
length of a line will require a much smaller AC input coupling capacitor.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
33
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.9 VCLP DAC
The VCLP pin provides the reference level for incoming signals in Sample and Hold Mode. The pin’s voltage can
be set by writing to the VCLP Configuration Register on register page 0. By default, the VCLP pin voltage is
established by an internal resistor divider which sets the voltage to 0.85 VA.
The VCLP buffer can also be disconnected and the pin driven externally by the another voltage in the
application, such as Vref from some CIS sensors.
Table 7. VCLP Voltage Setting
VCLP CONFIGURATION PAGE 0,
REGISTER 0x04, BITS[2:0]
TYPICAL VCLP OUTPUT
(FINAL SILICON TARGETS)
000
0.85VA (Default)
001
0.9VA
010
0.95VA
011
0.6VA
100
0.55VA
101
0.4VA
110
0.35VA
111
0.15VA
7.4.10 Gain and Offset Correction
Each input channel has individual settings for offset (DAC) and gain (PGA and CDS/SH gain).
7.4.10.1 Analog Offset
Analog offset (DAC) settings are individually adjustable for each color. In addition, there are (optionally) separate
settings for Even and Odd pixels being processed through each color channel. This feature is designed to
support specific CCD sensors that have two CCD transfer arrays per color, which may introduce different offset
for the Even versus Odd pixels.
COLOR1EVENDAC[9:0]
M
U
X
COLOR1ODDDAC[9:0]
Input Bias/
Clamping
OSR
Black
Level
Offset
DAC
COLOR1PGA[7:0]
CDS
or
Sample/Hold
Amplifier
PGA
Figure 12. Analog Offset Applied Prior to PGA
The Black Level Offset DACs are set with a 9 bit plus sign value. This gives an approximate adjustment range of
+/- 300 mV or +/- 600mV when the CDS/SH Gain is set to 1x or 2x.
The analog offset registers are found at Page 1, Registers 0x04h to 0x0Fh.
34
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.10.2 Digital Offset
In addition, digital offset can be added to color data at the output of the ADC in the Digital Offset block. The
digital offsets are a +/- 6 bit value. This value is summed with the upper 11 bits of the ADC output. Therefore, the
effective offset range is from +2016 to -2048 lsbs of the ADC output.
The digital offset registers are found at Page 1, Registers 0x10h to 0x15h.
16 Bit ADC
16
Digital
Offset
Figure 13. Digital Offset Applied to ADC Output
7.4.10.3 Even/Odd Offset Coefficients
Certain CCD sensors may have different offset voltages for the Even versus the Odd pixels. To optimize the
image processing of these pixels, separate coefficients can be stored, and applied for the Even and Odd pixels.
The Even/Odd offset feature is enabled by setting Page 0, Register 0x02h, Bit 0 = 1. Bimodal correction,
discussed below, is automatically disabled when Even/Odd offset coefficients are enabled.
Color 1 Even Offset
Color 2 Even Offset
Color 3 Even Offset
Color 1 Odd Offset
Color 1 Odd Offset
Color 1 Odd Offset
Figure 14.
•
•
•
Analog Gain
– The gain of each input channel can be adjusted at two points in the signal chain.
CDS/SH Gain - Page 1, Register 0x00h
– A 1x or 2x gain setting is available in the CDS/SH amplifier.
– By default, one common CDS/SH gain setting setting is used for all input channels. If desired, individual
CDS/SH gain settings can be used for each input. To enable this feature, set Page 1, Register 0x00h, Bit
2 = 1.
PGA Gain - Page 1, Registers 0x01h, 0x02h, 0x03h
– An 8 bit PGA (Programmable Gain Amplifier) is also available. The PGA gain curve is non-linear for
optimal performance in imaging applications, and is shown on Figure 15. The approximate gain equation
is:
Gain (V/V) = 180/(277-PGA_Code), Gain (dB) = 20log10(180/(277-PGA_Code))
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
(1)
35
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
The gain setting registers are found at Page 1, Registers 0x00h, 0x01h, 0x02h and 0x03h.
18
17
16
15
14
13
Gain (V/V) =
(180/(277-PGA Code))
12
11
Overall PGA Gain
10
9
Gain (dB) =
20LOG10(180/(277-PGA Code))
8
7
6
5
4
3
2
1
0
-1
0
32
64
96
128
160
192
224
-2
-3
-4
PGA Register Value
Overall Gain (dB)
Overall Gain (V/V)
Figure 15. PGA Gain vs. PGA Gain Code
•
36
Dual Gain Mode - Page 1, Register 0x00h, Bit 1, and Registers 0x16h, 0x17h, 0x18h
– In many scanning systems, the system illumination and optics characteristics will result in a much higher
optical efficiency in the pixels near the middle of the sensor, compared with the pixels at the beginning
and end of the sensor. If a single gain setting is used for all pixels, the middle pixels will be near clipping,
while the ones at the edges can be at 1/2 scale or lower. This results in lower signal to noise for the edge
pixels. To combat this problem, the LM98722 incorporates an optional Dual Gain system. When enabled,
the system provides a second set of PGA gain registers to set the “high” gain for each input channel. The
“normal” gain settings will be applied during the “active/white” pixels, while the “high” gain settings will be
applied for all pixels before and after the “active/white” pixels (see Figure 16).
– The Dual Gain enable bit is found at Page 1, Register 0x00h, Bit 1. The High Gain PGA settings are found
at Page 1, Registers 0x16h to 0x18h.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.11 LM98722 Typical Line Timing and Pixel Gain Regions
Figure 16. Typical Line Timing and Pixel Gain Regions
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
37
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.12 Automatic Black and White Level Calibration Loops
7.4.12.1 Calibration Overview
The offset and gain settings in the AFE will normally be set to optimize the range of the sensor output signal
within the ADC input range. These settings can be calculated in a host ASIC and loaded into the AFE during the
calibration procedure. To reduce the processing required to do these calculations, the LM98722 has built in
feedback or calibration loops that will automatically adjust the offset and gain settings. A number of register
values must be initially set to optimize the calibration for the particular application.
7.4.12.2 Different Modes for Different Needs
The calibration features of the LM98722 are not intended to be used during active scanning, but rather before
scanning begins, or in the page gap between images. Generally, more time is available to perform the initial
calibration before scanning begins. Page gap calibration must be necessariliy short to ensure the process
finishes in the limited number of scan lines available.
The Black and White Fine Tuning, and Black Calibration Only modes can be used during the page gap to adjust
for small differences in offset/gain that occur over time.
Black and White Full Calibration should be run before the initial scanning process, or periodically between major
jobs to take care of larger shifts in offset/gain of the input signal.
38
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.12.3 Calibration Initiation
Once these settings have been made, the Register Lock Control bit (Page 0, Register 0, Bit 0) should be set to
begin converting pixels. Once the sensor data from the test image is stable the calibration process can be started
by either setting the CAL register bit at Page 0, Register 0x01h, Bit 5, or by applying a logic high to the CAL input
pin. (Both of these inputs are active when the Register Lock Control is set.) The CAL input pin is particularly
useful for implementing page gap calibration.
7.4.12.4 Key Calibration Settings
Table 8. Key Calibration Settings
General Settings
Calibration Mode
Page 2, Register 0, Bits[1:0]
Black Calibration Only
00
Black and White Full Calibration
01
Black and White Fine Tuning:
10
Number of Lines
Page 2, Register 1
Black Loop Specific Settings
# Black Pixels Averaged
Page 2, Register 2, Bits[1:0]
Black Target
Page 2, Register 3
Black Pixels Start
Page 2, Register 8
ADAC Scaling
Page 2, Register 2, Bits[3:2]
DDAC Scaling
Page 2, Register 2, Bits[5:4]
DDAC enable/disable
Page 2, Register 0, Bit 2
White Loop Specific Settings
White Target
Page 2, Register 5
White Loop Tolerance
Page 2, Register 4, Bits[6:3]
White Pixel Averaging Window Size
Page 2, Register 4, Bits[2:0]
Active/White Pixels Start
Page 2, Registers 0x09h, 0x0Ah
Active/White Pixels End
Page 2, Registers 0x0Bh, 0x0Ch
The calibration loops are intended to be used prior to scanning the page or between pages being scanned. The
black loop calibrates the channel offset such that the ADC outputs the desired code for Optical Black Pixels. The
white loop calibrates the channel gain such that the ADC outputs the desired maximum white value when
scanning a white target image.
The Black Loop and White loop will both update until the # Lines setting is met. Settings of 1 to 254 lines will
cause the loops to run for that many lines, and then stop. A setting of 255 will cause the calibration loops to run
indefinitely.
While using the Auto Black Level Correction Loop, the DAC registers are re-written as required every line the
loop is running.
While using the Auto White Level Correction Loop, the PGA registers are re-written as required every line the
loop is running.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
39
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.12.5 General Black Loop Operation
During calibration, the following general process is performed:
Beginning at Black Pixels Start, the selected number of black pixels are averaged.
This Black Average value is compared with the Black Target to give the Black Error value.
In general, if the Black Average>> Black Target, the new DAC values will be lower than the previous ones. If the
Black Average < Black
Target the new DAC values will be higher than the previous ones.
The ADAC Scaling and DDAC Scaling values are used to balance the speed of convergence against the
tolerance for noise in the data. The smallest (1/8) scaling values will give slower convergence, but will make the
system respond more slowly to noisy data. The highest (1/2) will result in the fastest convergence, but will
respond more quickly to noisy data. The DDAC scaling factor of Linear - 1LSB adjust will result in a maximum
change of one LSB of the DDAC value, regardless of how great the difference between Black Average and Black
Target
The number of Black Pixels to be processed by the algorithm is set at Page 2, Register 2, Bits[1:0]. 4, 8, 16 or 32
pixels can be averaged together to determine the current Black Value. Averaging the highest number of pixels
possible for the sensor in use will improve the accuracy and repeatability of the Black Average value.
The delay from the end of the SH Interval to the first Black Pixel to be processed is set at Page 2, Register 8. A
delay of up to 255 pixels can be set.
7.4.12.6 ADAC/DDAC Convergence
At the beginning of the calibration process, the ADAC will be used to reduce the Black Error as much as
possible. Once further adjustments of the ADAC can no longer reduce the Black Error, the ADAC adjustments
will stop and the DDAC will be used. *If users would rather apply digital offset corrections in their ASIC, the
DDAC corrections can be omitted by setting the DDAC disable bit at Page 2, Register 0x00h, Bit 2.
Figure 17. Black Loop Timing
40
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.12.7 General White Loop Operation
The White Peak value is determined by a moving window average done throughout the Active/White pixels
region of the line (see to Figure 16). The size of the moving window is set at Page 2, Register 4, Bits[2:0]. 4, 8,
16 or 32 (default) pixels are averaged together at a time and compared with the previous Peak White value. If
the new White Average is greater than the previous Peak White value, then the Peak White value is set equal to
the White Average. The window is then shifted over to the next group of pixels (one window width) and a new
average is calculated. This process is repeated until the Active/White Pixels End value is reached. The final Peak
White value is then compared with the White Target value (Page 2, Register 5). The gain settings are then
adjusted to make the Peak White value closer to the White Target value.
7.4.12.8 White Loop Modes
• White Full Calibration (Cold start or Pre-Job): In this mode, the gain settings are completely reset to
default at the beginning of the loop. The first change or gain decision is whether the CDS/SH gain setting will
be 1x or 2x. Subsequent decisions are made to adjust the PGA setting to the provide the Peak White value
that is closest to the White Target value
• White Fine Tuning (Page Gap Calibration): In this mode, the previous gain settings are used as the starting
point. The CDS/ SH gain setting will not be changed. The PGA gain will be increased or decreased by one
step at a time, to fine tune the gain. This mode is normally used where only minor changes in the white level
are expected.
7.4.12.9 Bimodal (Automatic) Correction
Due to the architecture of the ADC used in the LM98722, it is possible that a small offset in the resulting data will
be present between the Even and Odd pixels processed by the device. This offset is referred to as a Bimodal
distribution in the data. It can occur because the signals being processed go through two different paths to
achieve the required throughput. Each of these paths can give a slightly different signal offset, resulting in the
bimodal distribution in output data, for a given fixed input voltage.
When the automatic Black Level (offset) correction circuit is engaged, a portion of that circuitry automatically
corrects the bimodal distribution. The bimodal correction applied is stored at Page 1, Registers 0x1Ch, 0x1Dh,
and 0x1Eh. The stored value is divided by two. Half is added to the Even pixels, and half is subtracted from the
Odd pixels.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
41
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.13 Coarse Pixel Phase Alignment
Precise placement of the CCD video signal sampling point is a critical aspect in any typical imaging application.
Many factors such as logic gate propagation delays and signal skew increase the difficulty in properly aligning
the CCD pixel output signals with the AFE input sampling points. The LM98722 provides two powerful features to
aid the system level designer in properly sampling the CCD video signal under a large range of conditions. The
first feature, discussed in this section, is the Coarse Pixel Phase Alignment block. As the name implies, this block
provides a very coarse range of timing adjustment to align the phase of the CCD Pixel output with the phase of
the LM98722 sample circuit. The second feature, discussed in Internal Sample Timing, is the block which is
designed for fine tuning of the sampling points within the selected Coarse Pixel Alignment Phase. A small portion
of a typical imaging application is shown in Figure 18.
SH
φ1Α
LM98724 CCD
Timing Generator
Outputs
φ2Α
OS3
CCD/CIS
Sensor
OS2
LM98724
Output Data Bus
OS1
Input Clock
(INCLK)
Figure 18. Typical AFE/CCD Interface
As shown in Figure 18, the LM98722 provides the timing signals to drive the CCD using external logic gates to
drive the high capacitance CCD clock pins. The pixels are shifted out of the CCD, thru the emitter follower
buffers and received by the LM98722 inputs for processing.
42
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
In an ideal application, depicted in Figure 19, the Pixel output signal would be in phase with the timing signals
that drove the CCD. The LM98722 input sampling clocks (CLAMP and SAMPLE) are adjustable within a pixel
period. By default, the pixel period (or pixel “phase”) is defined to be in line with the input clock. As shown in the
ideal case, Figure 19, CLAMP and SAMPLE can be properly adjusted to their ideal positions within the pixel
phase, shown in Figure 19 at the stable region near the end of the pedestal and data phases.
Figure 19. Clock Alignment in an Ideal Application
However, in a real system, propagation delays exist in all stages of the signal chain. These propagation delays
will lead to a shift in the CCD Pixel outputs with respect to the LM98722 input clock. The phase shift of the CCD
Pixel output, demonstrated in Figure 20, can lead to significant sample timing issues if not properly corrected.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
43
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Figure 20. CCD Output Phase Shift in a Real Application
In the default mode, the LM98722 sampling is performed during a clock period whose phase is aligned with the
input clock (ignoring any clock tree skew for the moment). The actual sampling clocks are adjustable within the
clock period, as shown in Figure 21 (shown for CDS mode in Figure 20) and further described in Internal Sample
Timing . As shown in Figure 20, the delay of the CCD Pixel output is shifted far enough that the fine CLAMP and
SAMPLE clocks cannot be placed in a stable portion of the waveform. To remedy this situation, the LM98722’s
Coarse Pixel Phase Alignment feature allows the designer to shift the entire phase of the analog front end with
respect to the input clock. This allows the designer to choose one of four sampling phases which best matches
the delay in the external circuitry. Once the “Coarse Pixel Phase” has been chosen, the designer can then fine
tune the sampling clocks using the fine adjustment (see Internal Sample Timing).
The four available Coarse Pixel Phases (PIXPHASE0 - PIXPHASE3) are depicted in Figure 21 (Mode 3),
Figure 22 (Mode 2) and Figure 23 (Mode 1). Also shown in the diagrams are the external input clock (INCLK)
and a typical CCD output delayed from the input clock.
44
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 21. Mode 3 Coarse Pixel Adjustment
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
45
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Figure 22. Mode 2 Coarse Pixel Phase Adjustment
46
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 23. Mode 1 Coarse Pixel Phase Adjustment
7.4.14 Internal Sample Timing
A typical CCD input signal is depicted in Figure 24 and Figure 25. Also shown are the internally generated
SAMPLE and CLAMP pulses. These signals provide the sampling points of the input signal (OSX). The timing of
SAMPLE and CLAMP is derived from an internal system clock (SYSCLK).
The pixel’s reference level input (depicted as VREF) is captured by the falling edge of the CLAMP pulse. In
Sample/Hold Mode the VREF input is a sample of the VCLP DC voltage. In CDS Mode the CLAMP pulse samples
the pedestal Level of the CCD output waveform.
The pixel’s signal level input (depicted as VSIG) is captured by the SAMPLE pulse. In either Sample/Hold or CDS
Mode, the VSIG input is the signal level of the CCD output waveform.
The LM98722 provides fine adjustment of the CLAMP and SAMPLE pulse placement within the pixel period. This
allows the user to program the optimum location of the CLAMP and SAMPLE falling edges. The available fine
tuning locations for CLAMP and SAMPLE are shown in Figure 25 and Figure 27 for each sampling mode (CDS
or S/H) and channel mode (3, 2, or 1 Channel).
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
47
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Figure 24. Pixel Sampling in CDS Mode
48
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 25. Pixel Sampling in S/H Mode
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
49
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
TPIXCLK
PIXPHASE
TSYSCLK = TPIXCLK / 21 (In Mode 3)
SYSCLK
OSX CLAMP
Control =
CLAMP Start and CLAMP Stop can be individually programmed
Valid programming range as follows:
CLAMP Start 0 to 38
CLAMP Stop 4 to 42
CLAMP Start
CLAMP Stop
CLAMP
ΔCLAMP= TSYSCLK / 2
OSX
SAMPLE
Control =
SAMPLE Start and SAMPLE Stop can be individually programmed
Valid programming range as follows:
SAMPLE Start 0 to 38
SAMPLE Stop 4 to 42
SAMPLE Start
SAMPLE Stop
SAMPLE
ΔSAMPLE= TSYSCLK / 2
Figure 26. 3 Channel (Mode 3) CLAMP and SAMPLE Timing
Figure 27. 1 or 2 Channel (Mode 1, Mode 2) CLAMP and SAMPLE Timing
50
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LS PIX 8-12 have one set of programmed ON/OFF points
during each line (during pixels)
LS PIX12
LS PIX11
LS PIX10
LS PIX9
LS PIX8
LS PIX7
LS PIX6
LS PIX5
LS PIX4
LS PIX3
LS PIX2
LS PIX1
LS PIX0
CCDTG
(low speed signals)
Out
Sequence Invert Control has 1 bit for each signal times 4 lines.
This is updated to the next value in the sequence at the end* of
each SH interval (end of final state, but before pixel clocking
begins)
This bit can be a 0 (normal) or 1 (invert) based on the stored
register settings
*Invert happens during transition from SH interval to pixels
timing to avoid glitches.
HSPIX Generator Block
Out
PhiA HSPIX Generator Block
Outb
Out
CP HSPIX Generator Block
Outb
Out
RS HSPIX Generator Block
Outb
Outb
Out
PhiB HSPIX Generator Block
Outb
PhiC HSPIX Generator Block
HSTG
(high speed signals)
Pin
Output
Polarity
/State
Output
Polarity
/State
Output
Polarity
/State
Output
Polarity
/State
Output
Polarity
/State
Output
Polarity
/State
Output
Polarity
/State
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Output
Polarity
/State
Output
Polarity
/State
Pin
Pin
Output
Polarity
/State
Output
Polarity
/State
Pin
Pin
Output
Polarity
/State
Output
Polarity
/State
SH5
SH4
SH3
SH2/CLKOUT
SH1
RS
CP
PHIA2
PHIA1
PHIB2
PHIB1
PHIC2
PHIC1
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
LM98722
7.4.14.1 CCD Timing Generation
A flexible internal timing generator is included to provide clocking signals to CCD and CIS sensors. A block
diagram of the CCD Timing Generator is shown in Figure 28.
Figure 28. CCD Timing Generator Block Diagram
Submit Documentation Feedback
51
Pixel Interval Sequence
Invert Control
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Examples of the various operating modes and settings are shown in Figure 29 through Figure 32. The detailed
pixel timing is somewhat dependent on the operating modes of the AFE circuitry regarding the number of
adjustment points for the on and off points of the different timing outputs.
Note: In addition to the timing adjustments shown, the polarity of all sensor clock signals can be adjusted by
register control.
Figure 29. Pixel Timing - 42 Timing Points Per Pixel in Mode 3
52
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 30. Pixel Timing - 28 Timing Points Per Pixel in Mode 2 and Mode 1
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
53
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Figure 31. Pixel Timing - Normal or 1/2 Rate Timing for High Resolution Sensors
54
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 32. Pixel Timing - Independent Inversion of Each Output
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
55
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.14.2 SH Interval Details - Multiple States Defined within SH Interval
In the LM98722, each SH Interval (the period when the high speed pixel timing is stopped) can have a selected
number of “States”, with each “State” having a specified duration. In the most common usage, each SH Interval
is the same, and there can be as many as 31 defined States within the SH Interval. During each State, the logic
level of each output signal can be defined as 1 or 0. The duration of the State, and the logic levels of the signals
are defined in configuration registers on register pages 3, 4 and 5.
Each State basic duration can be from 1 to 255 pixel periods. There is also a multiplier of 2x, 4x, 8x or 16x (Page
2, Register 0x17) that will increase SH State durations for sensors that require long SH pulse widths
If less than the maximum number of states are required, the first 0 duration State in the SH Interval will terminate
processing.
At the end of the SH Interval, a glitchless transition to pixel timing will occur. Similarly, at the end of the pixel
timing, a glitchless transition to the first state in the SH Interval will occur.
Some more complex sensors require different SH Interval timing in some sequence. The LM98722 can support
up to 4 different SH Interval Timings. The available 31 states are divided as follows when higher numbers of SH
Intervals are used:
Table 9. States within SH Interval Details
AVAILABLE STATES
56
# of SH Intervals
SH Interval 1
SH Interval 2
SH Interval 3
SH Interval 4
1
0 to 30
n/a
n/a
n/a
2
0 to 14
15 to 30
n/a
n/a
3
0 to 9
10 to 19
20 to 30
n/a
4
0 to 6
7 to 14
15 to 22
23 to 30
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 33. Sensor Timing SH Interval Details - Single SH Interval
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
57
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
An example showing a 4 SH Interval sequence is shown on Figure 34 through Figure 37.
Figure 34. Sensor Timing SH Interval Details - Multiple SH Intervals - 1 of 4
58
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 35. Sensor Timing SH Interval Details - Multiple SH Intervals - 2 of 4
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
59
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Figure 36. Sensor Timing SH Interval Details - Multiple SH Intervals - 3 of 4
60
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 37. Sensor Timing SH Interval Details - Multiple SH Intervals - 4 of 4
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
61
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.14.3 SH Outputs - Low Speed Line Timing Usage
While the PHI, RS and CP outputs generate high speed timing during the pixel portion of the line, the SH outputs
can be used to generate low frequency signals during this period. This can be useful to generate “mode” or
“resolution” control signals for certain sensors.
Each SH output has a programmed ON and OFF point within the line. These points are programmed with a 16
bit value that sets the pixel number where the transition occurs.
Programming ON and OFF in different orders will allow pulses that are normally low or normally high, always
high, always low, etc. A common 1x, 2x, or 4x multiplier (Page 2, Register 0x15) can be used to increase the
range (and reduce the resolution) of these ON/ OFF points, as well as the White/Active and Line Length pixels
settings.
SH Interval
Waveform set by SH
Interval Sequence
ON < OFF
ON
OFF
ON > OFF
OFF
ON
ON < OFF
ON
OFF
ON < OFF, OFF = 0xFFFFFFFF
ON
ON > OFF, ON = 0xFFFFFFFF
OFF
ON = 0, OFF = 0xFFFFFFFF
OFF = 0, ON = 0xFFFFFFFF
ON
OFF
Figure 38. Sensor Timing SH ON/OFF Details - Example Settings and Waveforms
62
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.14.4 Controlled Inversion
When using multiple SH Intervals, it is possible to invert the pixel portion of the line for any of the output signals
in any of the 4 Lines in the sequence. There is one bit per signal (or pair of signals for PHIA, PHIB and PHIC),
for each of the 1 to 4 lines in the sequence. Setting the bit for a particular output and line in the sequence will
cause the pixel portion of that line to be inverted. The transition to the next line in the sequence occurs at the
end of the SH Interval. Inversion can affect both the high speed timing signals (PHIx, RS, CP) and the low speed
ON/OFF behavior of the SH signals.
Figure 39 is an example of Polarity Override with a 2 Line sequence. Note that the PHIA1, SH1, SH2 and SH3
signals are inverted in Line 2, while all other signals are at the default polarity for both lines.
SH Interval 1
Line 1
SH Interval 2
Line 2
SH Interval 1
RS
0
0
0
1
0
1
0
1
0
0
0
0
PHIA1
SH1
SH2
SH3
SH4
SH5
0
0
Polarity
Override
Settings
Polarity
Override
Settings
SH Interval signal levels are set by SH Interval Information
Polarity for pixel portion of lines can be adjusted by Polarity Override Settings – Page 7, Registers 0x14 to 0x1D
Figure 39. Sensor Timing Mode Pin Output Details - Active Programmed Transition
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
63
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.15 CCD Timing Generator Master/Slave Modes
The internal Sensor Timing generator is capable of operating in Master Mode or in Slave Mode. The
Master/Slave operation is configured with the Master Mode Select bit (Page 0, Register 0x00, bit 1). In either
Master or Slave Mode, control bit data can be included in the LM98722 output data to indicate when each new
scan is starting as well as pixel information such as color, type (active, black, dummy, etc.), and the beginning of
each line.
7.4.15.1 Master Timing Generator Mode
In Master Timing Mode (Page 0, Register 0x00, bit 1 = 1), the LM98722 controls the entire CCD Timing
Generation based on INCLK and the Register Lock Bit (Page 0, Register 0, Bit 0) state. The Register Lock bit is
set by the user to initiate a new scan. The LM98722 controls when each new line of the scan begins and ends
based on the CCD Timing Generator register settings. Scanning is enabled as long as the Register Lock bit = 1.
The period of the line (integration time) is controlled by the SH Interval State Length settings (Page 3 Registers)
and the Line Length setting (Page 3, Registers 0x0D and 0x0E) as well as the Pixel Multiplier Factor (Page 2,
Register 0x0F) and SH State Length Multiplier (Page 2, Register 0x11) .
The line period from end of one SH Interval to the end of the next SH Interval is equal to:
Line Period = (Sum of SH Interval States x SH State Length Multiplier) + (Line Length Setting x Pixel Multiplier Factor)
pixels
(2)
7.4.15.2 Slave Timing Generator Mode
In Slave Timing Mode (Page 2, Register 0x00, bit 1 = 0), the LM98722 CCD Timing Generator is controlled by
the external SH_R pin. Each new line of a scan is initiated by an SH_R pulse. The period of the line (integration
time) is mainly controlled by the period of the incoming SH_R signal. The minimum period between SH_R pulses
should be at least the SH Interval duration as calculated in Equation 2, plus the number of pixels to be clocked
out of the CCD or CIS sensor.
Figure 40. SH_R to INCLK (PIXCLK or ADCCLK) Timing
64
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.15.3 Multiple SH Intervals
Multiple SH Intervals are supported for those CCD sensors that has different waveform and timing requirements
during successive SH Intervals. Up to 4 different SH Intervals are supported.
In the Multiple SH Interval mode, the Line Period can be different for each line, due to the possible different
settings for SH Interval duration. In that case the Line Periods would be calculated as follows:
Line Period1 = (Sum of SH Interval States1 x SH State Length Multiplier) + (Line Length Setting x Pixel Multiplier
Factor) pixels
Line Period2 = (Sum of SH Interval States2 x SH State Length Multiplier) + (Line Length Setting x Pixel Multiplier
Factor) pixels
Line Period3 = (Sum of SH Interval States3 x SH State Length Multiplier) + (Line Length Setting x Pixel Multiplier
Factor) pixels
Line Period4 = (Sum of SH Interval States4 x SH State Length Multiplier) + (Line Length Setting x Pixel Multiplier
Factor) pixels
In multiple SH Interval mode, the SH Interval States are subdivided as follows:
Table 10. Multiple SH Intervals Table
# SH INTERVALS
SH INTERVAL 1 STATES SH INTERVAL 2 STATES SH INTERVAL 3 STATES SH INTERVAL 4 STATES
1
0 to 30
2
0 to 14
15 to 30
3
0 to 9
10 to 19
20 to 30
4
0 to 6
7 to 14
15 to 22
23 to 30
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
65
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.15.4 Support for CIS Sensors
In CIS Sensor modes, the SH (LampR), SH2 (LampG), SH3 (LampB) and SH4 (LampIR) outputs are configured
as Lamp illumination control outputs. In CIS mode, the number of lines/colors in the lamp sequence is selected
by the Multiple SH Interval setting at Page 2, Register 10h, Bits 1:0. Sequences of 2, 3 or 4 lines/colors are
supported in CIS mode. By definition, the standard CCD timing mode is equivalent to a CIS mode with length =
1.
Two different CIS modes are supported (CISa and CISb, selected at Page 2, Register 0x10h, Bits 4:3):
In CISa, there can be 2, 3 or 4 colors in the sequence, to support sensors with as many as 4 different lamp
colors. In this mode, the PGA and DAC settings are controlled by the channel settings, regardless of what line in
the sequence is being processed.
Figure 41. Mode 3, 3 Color Sequence, CISa Default
66
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 42. Mode 3, 3 Color Sequence, CISb
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
67
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
In CISb, when a 2 line sequence is selected, it is necessary to choose which coefficients are used during the 2
different lines in the sequence. this selection is made with the CISb Color Coefficient Select at Page 2, Register
10h, Bits 6:5. Following is an example of a 2 color sequence, where Red and Green are the selected colors:
(1)
Use Page 2, Register 10h, Bits 6:5 to choose which SHx Lampx outputs are used, and which coefficients are used in
CISb 2 color sequence.
Figure 43. Mode 3, 2 Color Sequence, CISb
68
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
To support monochrome scanning with an RGB CIS, select Mode 3, and a 1 line sequence. The LampR, LampG
and LampB On/Off times will apply for every line. The On/Off times and relative channel gains can both be
adjusted to achieve the desired white balance. Lamps can be on either simultaneously if the CIS and power
budget allow, or sequentially.
(1)
Lamps can be on simultaneously , or sequentially within each line
Figure 44. Mode 3, Mono – 1 Color CCD Timing
7.4.15.5 LVDS Output Format - LM98714 Mode
7 Bit Frame
TXCLK
TXOUT2
DB[12]n-1
DB[11]n-1
DB[10]n-1
DB[9]n-1
DB[15]n
DB[14]n
DB[13]n
DB[12]n
DB[11]n
DB[10]n
DB[9]n
TXOUT1
DB[4]n-1
DB[7]n-1
DB[3]n-1
DB[2]n-1
DB[8]n
DB[7]n
DB[6]n
DB[5]n
DB[4]n
DB[3]n
DB[2]n
TXOUT0
CB[3]n-1
CB[2]n-1
CB[1]n-1
CB[0]n-1
DB[1]n
DB[0]n
CB[4]n
CB[3]n
CB[2]n
CB[1]n
CB[0]n
Pixel “n-1”
Pixel “n”
Figure 45. LVDS Output Bit Alignment and Data Format
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
69
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.16 LVDS Control Bit Coding - LM98714 Mode
The 5 control bits included in the LVDS data stream are coded as follows:
The "active" and "black" pixel tags are programmable tags that the LM98722 provides in order to identify how
many pixels have been processed since the falling edge of SH.
Which pixels are given "Active" and "Black" CB tags is controlled by Page 2, Registers 0x02, 0x08-0x0C, and
0x0F. (# Black Pixels Averaged, Black Pixels Start, Active/White Pixels Start, Active/White Pixels End, and Line
Length Multiplier).
The LM98722 counts the number of pixel periods after the SH Interval: If the number of pixel periods after the
SH Interval is greater than (Black Pixels Start) and less than (Black Pixels Start + # Black Pixels Averaged) the
CB bits will indicate that the pixel is a Black pixel. If the number of pixel periods after the falling edge of SH is
between Active/White Pixels Start and Active/White Pixels End, the CB bits will indicate that the pixel is an Active
pixel.
7.4.16.1 Latency Compensation of CB Bits
By default, the CB bits will be compensated for the latency through the AFE signal chain. This compensation can
be turned off by setting Page 8, Register 0x08, Bit 2 = 1.
Table 11. Latency Compensation of CB Bits
BITS
DESCRIPTION
CB[4]
0
Not the beginning of line
1
Beginning of Line (This bit is high during the SH Interval)
CB[3:0]
0000
Dummy Pixels
0001
Red Active Pixels
0010
Green Active Pixels
0011
Blue Active Pixels
0100
IR1 Active Pixels
0101
IR2 Active Pixels
0110
Red Black Pixels
0111
Green Black Pixels
1000
Blue Black Pixels
1001
IR1 Black Pixels
1010
IR2 Black Pixels
1111
Beginning of Scan (This bit is high during the SH Interval of the first
line after the Lock Bit transitions from low to high)
70
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.17 Flexible LVDS Formatting Mode: Mapping
7 Bit Frame
TXCLK
TXOUT2
DB[12]n-1
DB[11]n-1
DB[10]n-1
DB[9]n-1
DB[15]n
DB[14]n
DB[13]n
DB[12]n
DB[11]n
DB[10]n
DB[9]n
TXOUT1
DB[4]n-1
DB[7]n-1
DB[3]n-1
DB[2]n-1
DB[8]n
DB[7]n
DB[6]n
DB[5]n
DB[4]n
DB[3]n
DB[2]n
TXOUT0
CB[3]n-1
CB[2]n-1
CB[1]n-1
CB[0]n-1
DB[1]n
DB[0]n
CB[4]n
CB[3]n
CB[2]n
CB[1]n
CB[0]n
Pixel “n-1”
Pixel “n”
Figure 46. LVDS Output Bit Alignment and Data Format
In Flexible LVDS Formatting Mode, the values highlighted in red can be substituted with other CB tag
information. Table 12 shows the different CB information that can be selected:
Table 12. Selectable CB Tag Information
SETTING
CB TAG INFORMATION
0000
Original CB or Data
0001
CBO0 from LM98714 definition
0010
CBO1 from LM98714 definition
0011
CBO2 from LM98714 definition
0100
CBO3 from LM98714 definition
0101
CBO4 from LM98714 definition
0110
R - High for a red channel pixel
0111
G - High for a green channel pixel
1000
B - High for a blue channel pixel
1001
Parity - 21 bit if TXOUT0 Enabled, 14 bit if TXOUT0 Disabled
1010
Ping - High for pixels processed by the Ping section of a channel, low for Pong
1011
Line# lsb - Line = 0 to 3 for lines 0 to 3 in multiline sequences
1100
Line# msb
1101
Black Loop Pixels - High for pixels processed by the Black Loop
1110
White Loop Pixels - High for pixels process by the White Loop
1111
CLP Pixels - High for pixels where the input CLP switch is closed
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
71
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.17.1 TXOUT0 Disable
The TXOUT0 data pair can be disabled. In combination with the new Flexible LVDS Formatting Mode, this can
support applications where only the upper 14 MSB of data are required. This will save one pair of LVDS wires in
the cable, and reduce the LM98722 slightly.
In addition, if fewer than 14 bits are required, the D2 and D3 bits can be replaced with the desired CB
information, selected from Table 12.
7.4.17.2 Parity
A parity bit is available for use as one of the CB bits. Parity is calculated based on all bits being sent via the 21
or 14 bit LVDS link except:
• If any bit is selected to transmit CB Parity, it will not be used in the calculation
• If any bit is transmitting a scrambler key bit when scrambler mode 2 is selected, it will not be used in the
calculation.
The total parity across the 21 or 14 output bits (excluding any scrambler key bit) will be even.
7.4.17.3 Latency Compensation of CB Bits
By default, the CB bits will be compensated for the latency through the AFE signal chain. This compensation can
be turned off by setting Page 8, Register 0x08, Bit 2 = 1.
7.4.18 LVDS Data Randomization for EMI Reduction
While LVDS transmissions will inherently reduce the amount of electromagnetic energy, further reductions can be
achieved by randomizing the data being sent over the link. A built in “scrambler” feature provides a number of
different modes to suit different applications and host processing capabilities. One key part of the scrambler is a
linear feedback shift register (LFSR) implementation to provide pseudo-random sequence “keys” to randomize
the image data. The basic implementation of an LFSR is shown in Figure 47:
XOR
20 19 18
...
2
1
0
Figure 47. Basic Implementation of an LFSR
72
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
The LFSR algorithm used in the LM98722 is an n=21 maximal length right-shift implementation as shown in
Figure 47. As a reference for FPGA and ASIC developers, the sequence is the same as that created by the
Synopsys DW component DW03_lfsr_load with inverted outputs. The preload or starting value for the sequence
is 0x000001h.
If the prs (serial-type) output is selected (MODE = 01, SUB_MODE = 0X), the 21 bits of the LFSR are shifted one
position to the right on each TXCLK.
For clarity, the first 11 values in the prs sequence are:
0x000001h
0x100000h
0x080000h
0x040000h
0x020000h
0x010000h
0x008000h
0x004000h
0x002000h
0x001000h
0x000800h
If the pprs (parallel-type) output is selected (MODE = 01, SUB_MODE = 1X), the next 21 coefficients of the shiftin term are calculated in parallel, and the LFSR is loaded with these coefficients: the effect is equivalent to
clocking the LFSR 21 times in serial mode. For clarity, the first 11 values in the pprs sequence are:
0x000001h
0x080001h
0x020001h
0x0A8001h
0x002001h
0x082801h
0x022201h
0x0AAA81h
0x000021h
0x080029h
0x120023h
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
73
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
A summary and description of each of the modes and submodes is shown in Table 13.
Table 13. Mode and Submode Summary
MODE
Page 0, Register 0x05
Bits 4:3
00
SUB_MODE
Page 0, Register 0x05
Bits 2:1
DESCRIPTION
Scrambler Disabled
Full Scrambler Enabled. Sub-mode Settings Select:
01
00
send lvds_data[20:0] bitwise XOR with prs[20:0]
01
send prs[20:0]
10
send lvds_data[20:0] bitwise XOR with pprs[20:0]
11
send pprs[20:0]
1 bit scrambler with key of prs[0] send lvds_data[20:0] bitwise XOR with prs[0], with lvds_data[k] = 0 send
prs[0] on lvds_out[k] k is selected with following settings:
00
10
k = 0 (DB0 in CMOS and 714 modes, CB0 in flexible,
16 bit mode)
01 (TXOUT0 Disable = 0)
k = 5 (DB0 (LSB) in flexible, 16 bit mode)
01 (TXOUT0 Disable = 1)
k = 7 (DB2 (LSB) in flexible, 14 bit mode)
10
k = 16 (CB0 in 714 mode)
11
k = 20 (CB4 in 714 mode)
1 bit scrambler with key of lvds_data[k]. send lvds_data[20:0] bitwise XOR with lvds_data[k] with lvds_out[k] =
lvds_data[k]:
00
11
k = 0 (DB0 in CMOS and 714 modes, CB0 in flexible,
16 bit mode)
01 (TXOUT0 Disable = 0)
k = 5 (DB0 (LSB) in flexible, 16 bit mode)
01 (TXOUT0 Disable = 1)
k = 7 (DB2 (LSB) in flexible, 14 bit mode)
10
k = 16 (CB0 in 714 mode)
11
k = 20 (CB4 in 714 mode)
7.4.18.1 Mode 00: Scrambler Disabled
Mode 00: Scrambler Disabled
7.4.18.2 Mode 01: Full Scrambler Using The Full 21-bit Pseudo Random Sequence
There are 4 sub-modes: (a) the 21-bit output will be bit-wise XORed with the 21-bit serial pseudo-random
sequence. i.e. lvds_data[20:0] ^ prs[20:0]; (b) the 21-bit serial pseudo random sequence will be output directly;
(c) the 21-bit output will be bit-wise XORed with the 21-bit parallel pseudo-random sequence. i.e. lvds_data[20:0]
^ pprs[20:0]; (d) the 21-bit parallel pseudo random sequence will be output directly. In all sub-modes, the
sequences start m clock cycles after the de-assertion of the bol where m is defined as the analog latencies in 1ch, 2-ch and 3-ch modes. In other words, the output starts the same way as the up-count test pattern mode.
Unlike the up-count test pattern mode, the 21-bit pseudo-random sequence runs at the ADC (same as TXCLK)
rate, not pixel or line rate.
74
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.18.3 Mode 10: One bit scrambler using the prs shift bit only, sending this bit out on a CB bit
Each bit of lvds_data[20:0] is XORed with prs[0]. One selected bit, lvds_data[k] is replaced with 0 before the
XOR procedure. The resulting output lvds_out[20:0] has bit k replaced by prs[0]. The bit k selection is flexible to
support different mappings of lvds_out depending on output settings as follows:
• LVDS Mapping - 714 Default Mode versus Flexible Mode (Since the location of CB bits changes depending
on which is selected) Mapping select is at Page 8, Register 8, Bit 0.
• CMOS Mode versus LVDS Mode (since only lvds_out[15:0] are available in CMOS mode) CMOS/LVDS mode
select at Page 0, Register 5, Bit 7.
• LVDS 3 Pair Mode versus LVDS 2 Pair Mode (Since TXOUT0 pair is disabled in 2 Pair Mode(txout0_dis=1))
TXOUT0 Disable at Page 8, Register 8, Bit 1.
Figure 48. LVDS_out[20:0] Mapping In Different Modes
If an output bit is replaced with the scrambler key, that bit position/value is excluded from the calculation of the
parity.
7.4.18.4 Mode 11: “LSB” scrambler
The “LSB” selected from lvds_data[k] is used to scramble the output. The lvds_data[20:0] key bit k, as selected
in Mode 10 above is used (as the “LSB”) to XOR the other bits. The key bit itself is not replaced.
7.4.18.5 Scrambler Inhibit Bit Select
This feature allows individual bits in the LVDS output stream to be non-scrambled. This can be used as a setup
and debugging aid during initial system development, or as a permanent feature to simplify the data decoding
task. The tradeoff will be somewhat compromised EMI reduction over a fully scrambled LVDS data stream.
The controls for this feature are located as follows:
Scrambler Inhibit 0 - Page 8, Register 0x12h, Bits 6:0 - LVDS[6:0]
Scrambler Inhibit 1 - Page 8, Register 0x13h, Bits 6:0 - LVDS[13:7]
Scrambler Inhibit 2 - Page 8, Register 0x14h, Bits 6:0 - LVDS[20:14]
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
75
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.19 LVDS Drive Strength Adjust
The LVDS outputs may be decreased in strength to reduce EMI generation, or increased in strength to improve
noise immunity.
Page 8, Register 8, Bits 5:4 can be adjusted as follows (in terms of VOD into 100 Ω termination):
Table 14. LVDS Strength
00 -
Decrease of approximately 100 mV
01 -
Decrease of approximately 50 mV
10 -
Default - Approximately 350 mV
11 -
Increase of approximately 50 mV
7.4.20 LVDS Output Timing Details
INCLK
tIDO
7 Bit Frame Period
TXCLK
(single ended)
Pixel “n-1”
Pixel “n”
TXOUT2
CB[1]n-1
(single ended)
CB[0]n-1
DB[15]n-1
DB[14]n-1
CB[4]n
CB[3]n
CB[2]n
CB[1]n
CB[0]n
DB[15]n
DB[14]n
TXOUT1
DB[10]n-1
(single ended)
DB[9]n-1
DB[8]n-1
DB[7]n-1
DB[13]n
DB[12]n
DB[11]n
DB[10]n
DB[9]n
DB[8]n
DB[7]n
TXOUT0
(single ended)
DB[2]n-1
DB[1]n-1
DB[0]n-1
DB[6]n
DB[5]n
DB[4]n
DB[3]n
DB[2]n
DB[1]n
DB[0]n
DB[3]n-1
TXpp0
TXpp1
TXpp2
TXpp3
TXpp4
TXpp5
TXpp6
Figure 49. LVDS Data Output Mode Specification Diagram
76
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.20.1 Optional TXCLK Delay
The LM98722 includes a selectable (off by default) delay of TXCLK. This delay can be enabled (Page 8, Register
0x08, Bit 3) to improve timing margin between the TXCLK and TXOUTx signals when using certain LVDS
deserializers. The default/off setting is intended to be compatible with the LM98714 LVDS timing.
7.4.21 LVDS Data Latency Diagrams
Figure 50. Mode 3 LVDS Data Latency
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
77
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Figure 51. Mode 2 LVDS Data Latency
78
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Figure 52. Mode 1 LVDS Data Latency
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
79
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.22 Data Test Patterns
The data test patterns present different data to the input of the LVDS serializer block. There are two basic groups
of test patterns:
• LVDS Output Pattern Modes - These patterns are applicable to all 21 bits of the LVDS interface.
• AFE Output Pattern Modes (Default) - These patterns are applicable to the 16 bit AFE data sent to the LVDS
interface.
• All Test Pattern Modes are selected at Page 0, Register 6.
7.4.22.1 LVDS Output Pattern Modes
7.4.22.1.1 Worst Case Transitions (Alternating 0x2A/0x55 on Each LVDS Pair)
This test mode provides an LVDS output with the maximum possible transitions. This mode is useful for system
EMI evaluations, and for ATE timing tests.
The effective data values are an alternating pattern between 21’b101010101010101010101 (0x155555) and
21’b010101010101010101010 (0x0AAAAA). This test pattern resets to 0x155555 at the selected event (BOL or
BOS).
Figure 53. Worst Case Transitions (Alternating 0x2A/0x55 on Each LVDS Pair)
7.4.22.1.2 Fixed Output Data
This mode sends a fixed repeating data pattern to each of the indicated LVDS output pairs. This is useful for
system debugging of the LVDS link and receiver circuitry. There are 4 different choices within this mode:
• 0x2A (0101010b) (All 3 data pairs)
• 0x55 (1010101b) (All 3 data pairs)
• 0x00 (0000000b) (*All 3 data pairs + clock pair)
• 0x7F (1111111b) (*All 3 data pairs + clock pair)
*Since the 0x00 and 0x7F patterns also affect the clock pair, they cannot be used for deserializer and
downstream testing. They are useful for DC measurements of the LVDS outputs.
7.4.22.2 AFE Output Pattern Modes
There are 3 different types of AFE Output Patterns:
• Normal ADC/AFE output (Default)
• Up-Counter Data
• Fixed AFE Patterns
80
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.22.2.1 Up-Counter Data
The counter will be reset to 0xFFFF during the BOS (Beginning Of Scan) SH Interval. When the AFE up-counter
is selected, the ramp begins at the BOS, and increments by 1 at either the pixel rate or at the line rate (every
BOL). This data can be useful as it can provide a grayscale image that increases in intensity down the “page”.
Alternately, it can provide data that increments at the pixel rate. Either of these forms can be very useful in
debugging the downstream data processing system.
7.4.22.2.2 Fixed AFE Pattern
The fixed AFE patterns allow the CB coding information to be sent normally, while specific data is used to
replace the AFE output. This can be useful in debugging portions of the downstream data processing system.
• 0xFF00 (0x1111111100000000b) fixed data
• 0xAA55 (0x1010101001010101b) fixed data
• 0x0000 (0x0000000000000000b) fixed data
• 0xFFFF (0x1111111111111111b) fixed data
• 0x00FF (0x0000000011111111b) fixed data
• 0x55AA (0x0101010110101010b) fixed data
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
81
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.23 CMOS Output Format
Figure 54. CMOS Data Output Format (Mode 3 Shown)
82
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.24 CMOS Output Data Latency Diagrams
INCLK =
ADCCLK
tLAT3
PIXPHASE0
tLAT3
PIXPHASE1
tLAT3
PIXPHASE2
tLAT3
PIXPHASE3
OSR
OSG
OSB
CLKOUT
DOUTx
MSB
LSB
Data latency shown is for Mode 3 in relation to PIXPHASE0 with the processing order set to OS RDOSGDOS B. If the incoming pixels are not aligned with
PIXPHASE0, one of the remaining PIXPHASEs can be selected as the sampling phase without effecting the output data location.
Figure 55. Mode 3 CMOS Output Latency
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
83
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
INCLK =
ADCCLK
tLAT2
PIXPHASE0
tLAT2
PIXPHASE1
tLAT2
PIXPHASE2
tLAT2
PIXPHASE3
OSR
OSG
OSB
CLKOUT
DOUTx
MSB
LSB
Data latency shown is for Mode 2 in relation to PIXPHASE0 with the processing order set to OS GDOS B. If the incoming pixels are not aligned with
PIXPHASE0, one of the remaining PIXPHASEs can be selected as the sampling phase without effecting the output data location.
Figure 56. Mode 2 CMOS Output Latency
84
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
INCLK =
ADCCLK
tLAT1
PIXPHASE0
tLAT1
PIXPHASE1
tLAT1
PIXPHASE2
tLAT1
PIXPHASE3
OSR
OSG
OSB
CLKOUT
DOUTx
MSB
LSB
Data latency shown is for Mode 1 in relation to PIXPHASE0 with the processing channel configured to OS R. If the incoming pixels are not aligned with
PIXPHASE0, one of the remaining PIXPHASEs can be selected as the sampling phase without effecting the output data location.
Figure 57. Mode 1 CMOS Output Latency
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
85
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.25 Serial Interface
A serial interface is used to write and read the configuration registers. The interface is a four wire interface using
SCLK, SEN, SDI and SDO connections. SDI and SDO can be connected together to support the same format
and connectivity as previous LM98714 designs. The CE pin should be tied to GND to support LM98714
compatible communications. This will set the device address bits to 00.
Table 15. Serial Interface "CE" Pin Definition
CE LEVEL
ADDRESS
VD
01
Float
10
GND
00
The main input clock (INCLK) to the LM98722 can be active or stopped when accessing the Serial Interface.
Care should be taken to avoid stopping or starting the INCLK during Serial Interface communication.
NOTE
After either starting or stopping INCLK, or after Software Reset (Register Page 0, Address
1, [4:3]), users should wait for 50 ms to allow the internal PLL and logic to stabilize before
resuming Serial Interface communications.
7.4.25.1 Serial Interface Operating Modes
• LM98714 Compatible Mode (Default): By default the serial interface is compatible with the LM98714
interface, allowing SDI and SDO to be connected and driving by a single pin on the host.
• LM98722 4 Wire 16+ Clock Mode (Default): The 4 Wire 16+ Clock Mode is essentially the same as the
LM98714 Compatible Mode, but using all 4 wires, with separate SDO and SDI signals between the Host and
Slave. This requires additional wires, but removes the need for a bidirectional signal. A valid transaction is
recognized after a minimum of 16 SCLK while SEN is low.
• LM98722 25+ Clock Mode (Selected when Page 0, Register 0x01h, Bit 7=1: This mode forces the serial
interface logic to only process a transaction with 25 or more SCLK while SEN is low. This mode can be used
with either 3 or 4 wire connections. In all of the above cases, the final 16 bits on SDI (before the rising edge
of SEN) are processed by the serial interface logic. Any earlier information on SDI is ignored.
• Serial Interface in Absence of MCLK
• Clockless (MCLK stopped) Mode (always enabled if MCLK stopped): When the input MCLK is stopped,
Data Read operation is exactly the same as MCLK present mode. The Data Write operation no longer
provides a free readback of the previously written data. See Figure 60 and Figure 63.
7.4.25.2 Serial Interface in Absence of MCLK
Clockless (MCLK stopped) Mode (always enabled if MCLK stopped) - When the input MCLK is stopped, Data
Read operation is exactly the same as MCLK present mode. The Data Write operation no longer provides a free
readback of the previously written data. See Figure 60 and Figure 62.
7.4.25.3 Writing to the Serial Registers
To write to the serial registers, the timing diagram shown in Figure 58 must be met. First, SEN is toggled low.
The *previously addressed device assumes control of the SDO pin during the first eight clocks of the command.
During this period, data is clocked out of the device at the rising edge of SCLK. At the rising edge of ninth clock,
the LM98722 releases control of the SDO pin. At the falling edge of the ninth clock period, the master should
assume control of the SDI pin and begin issuing the new command. SDI is clocked into the LM98722 at the
rising edge of SCLK. The remaining bits are composed of the “write” command bit (a zero), two device address
bits (00, 01 or 10 for the LM98722), five bit register address to be written, and the eight bit register value to be
written. When SEN toggles high, the register is written to, and the LM98722 now functions with this new data.
The previously addressed device could be another device on a shared serial interface or this device. If the
previous command was to this device, and was a read, then the SDO pin will be driven during the first eight
clocks. If the previous command was to this device and was a write, then the SDO pin will only be driven if the
serial interface is in “MCLK active” mode.
86
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.4.25.4 Reading The Serial Registers
To read to the serial registers, the timing diagram shown Figure 59 must be met. First, SEN is toggled low. The
LM98722 assumes control of the SDO pin during the first eight clocks of the command. During this period, data
is clocked out of the device at the rising edge of SCLK. The eight bit value clocked out is the contents of the
previously addressed register, regardless if the previous command was a read or a write. At the rising edge of
ninth clock, the LM98722 releases control of the SDO pin. At the falling edge of the ninth clock period, the
master should assume control of the SDI pin and begin issuing the new command. SDI is clocked into the
LM98722 at the rising edge of SCLK. The remaining bits are composed of the “read” command bit (a one), two
device address bits (zeros for the LM98722), five bit register address to be read, and the eight bit “don’t care”
bits. When SEN toggles high, the register is not written to, but its contents are staged to be outputted at the
beginning of the next command.
Examples of Serial Writes and Reads in the various modes are shown in Figure 58 through Figure 64.
7.4.25.5 LM98714 Compatible 3 Wire Serial Signaling
1
9
n-15
n
SCLK
SEN
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
SDO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
Device outputting register contents from this
write command if MCLK is present.
If MCLK is not present, no data output will occur.
Previously addressed slave
outputting register contents from
previous command.
(W)
SDI
X
X
X
X
X
X
X
X
X
X
X
X
0
CE CE
A4
1
0
A3
A2
A1
A0
DI
[7]
DI
[6]
DI
[5]
DI
[4]
DI
[3]
DI
[2]
DI
[1]
DI
[0]
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Master issues “write” bit (0), 2 “chip enable” bits (00, 01 or 10), five bit
register address, and eight bit register value to be written.
Only final 16 bits of SDI data before rising edge of /SEN are processed.
Figure 58. Serial Write - LM98714 Compatible Connection
1
9
n-15
n
SCLK
SEN
SDIO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
Previously addressed slave
outputting register contents from
previous command.
X
X
1
(R)
CE CE
A4
1
0
A3
A2
A1
A0
DI
[7]
DI
[6]
DI
[5]
DI
[4]
DI
[3]
DI
[2]
DI
[1]
DI
[0]
Master issues “read” bit (1), 2 “chip enable” bits (00, 01 or 10), five bit register
address, and eight “don’t care” bits. Register contents are not altered.
Only final 16 bits of SDI data before rising edge of /SEN are processed.
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
X
X
Device outputting register contents
addressed in read command.
Figure 59. Serial Read - LM98714 Compatible Connection
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
87
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.25.6 LM98722 4 Wire Serial Signaling
1
9
n-15
n
SCLK
SEN
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
SDO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
Device outputting register contents from this
write command if MCLK is present.
If MCLK is not present, no data output will occur.
Previously addressed slave
outputting register contents from
previous command.
(W)
SDI
X
X
X
X
X
X
X
X
X
X
X
X
0
CE CE
A4
1
0
A3
A2
A1
A0
DI
[7]
DI
[6]
DI
[5]
DI
[4]
DI
[3]
DI
[2]
DI
[1]
DI
[0]
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Master issues “write” bit (0), 2 “chip enable” bits (00, 01 or 10), five bit
register address, and eight bit register value to be written.
Only final 16 bits of SDI data before rising edge of /SEN are processed.
Figure 60. Serial Write - 4 Wire Connection - 25+ Clock Mode
1
9
n-15
n
SCLK
SEN
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
SDO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
Device outputting register contents
addressed in read command.
Previously addressed slave
outputting register contents from
previous command.
SDI
X
X
X
X
X
X
X
X
X
X
X
X
1
(R)
CE CE
A4
1
0
A3
A2
A1
A0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Master issues “read” bit (1), 2 “chip enable” bits (00, 01 or 10), five bit register
address, and eight “don’t care” bits. Register contents are not altered.
Only final 16 bits of SDI data before rising edge of /SEN are processed.
Figure 61. Serial Read - 4 Wire Connection - 25+ Clock Mode
88
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
1
9
n-15
n
SCLK
SEN
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
SDO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
Previously addressed slave outputting
register contents from last command.
Device outputting register contents from this write
command if MCLK is present.
If MCLK is not present, no data output will occur.
(W)
SDI
X
X
X
X
X
X
X
X
X
CE CE
1
0
0
A4
A3
A2
A1
A0
DI
[7]
DI
[6]
DI
[5]
DI
[4]
DI
[3]
DI
[2]
DI
[1]
DI
[0]
X
X
X
Master issues “write” bit (0), 2 “chip enable” bits (00, 01 or 10), five bit
register address, and eight bit register value to be written.
Only final 16 bits of SDI data before rising edge of /SEN are processed.
Figure 62. Serial Write - 4 Wire Connection - 16+ Clock Mode
1
n-15
9
n
SCLK
SEN
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
SDO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
Previously addressed slave outputting
register contents from last command.
SDI
X
X
X
X
X
X
X
X
X
1
(R)
CE CE
1
0
A4
A3
Device outputting register contents
addressed in read command.
A2
A1
A0
DI
[7]
DI
[6]
DI
[5]
DI
[4]
DI
[3]
DI
[2]
DI
[1]
DI
[0]
X
X
X
Master issues “read” bit (1), 2 “chip enable” bits (00, 01 or 10), five bit register
address, and eight “don’t care” bits. Register contents are not altered.
Only final 16 bits of SDI data before rising edge of /SEN are processed.
Figure 63. Serial Read - 4 Wire Connection - 16+ Clock Mode
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
89
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
7.4.25.7 Serial Interface Timing Details
tSENSC
tSCSEN
tIS
SCLK
tHZ
tOD
tIH
SEN
SDIO
DO DO DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2] [1] [0]
(R) CE CE
1 [1] [0] A4 A3 A2 A1 A0
x
x
x
x
x
x
x
x
DO DO DO DO DO DO
[7] [6] [5] [4] [3] [2]
tSENW
INCLK
Figure 64. Serial Interface Specification Diagram
90
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
7.5 Registers Maps
7.5.1 Configuration Registers
The LM98722 operation is very flexible to support a wide variety of sensors and system designs. This flexibility is
controlled through configuration registers which are first summarized, then described in full in the register tables.
Because the serial interface only allows 5 address bits, a register paging system is used to support the larger
number of required registers.
The page register is present at the highest address (1Fh or 11111b) of the currently selected page. The power
on default setting of the page register is 00. Writing other values to this register allows the other pages to be
accessed.
Once all registers are written, the Register Lock Control bit (Page 0, Register 0, Bit 0) is set to 1 to start the state
machines and initiate the converting of pixels. If Slave mode is selected, SH_R pulses must also be input to
trigger this process.
NOTE
When Register Lock Control = 1, many registers are locked to prevent state machines
from becoming corrupted, while others are accessible to allow control of necessary
functions. The registers and bits that are still writable are indicated in Boldface print in the
Bits and Register Description columns of the Register Definition Details table.
Operational Setup Sequence:
Ensure Lock Bit (Page 0, Register 0, Bit 0) = 0 for following setting writes
Apply either no INCLK or a stable INCLK to ensure accurate serial communications
Page 0
• Set AFE mode (# of input channels)
• Set output data format
• Enable data outputs
• Set AFE biasing
• Set AFE Clamp and Sample timing
• Setup Slave or Master Mode
Page 1
• Set Gain Mode (Single or Dual)
• Set CDS/SH Gain
• Set PGA
• Set DAC settings
Page 2
• Set Input Clamping Settings
• Set Black Pixel Start and # Black Pixels Averaged
• Set Active White Pixels Start and End
• Set Line Length (Master Mode Only)
• Set # Pixel Multiplier, SH Line Sequence # and SH State Length Multiplier
• Set PHI, RS, CP On and Off delay settings
• Set Spread Spectrum control settings
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
91
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Registers Maps (continued)
Page 3
• Set SH State Length settings
Page 4
• Set SH Interval State Settings for PHI, RS, CP
Page 5
• Set SH Interval State Settings for SH1 to SH5
Page 6
• Set PHI, RS, CP pattern bit fields and rate (normal or 1/2 rate)
Page 7
• Set SHx On, Off settings if needed
• Set CLK invert settings for multi-line sequences if needed
Page 8
• Set CLK output activity, polarity, enable
• Set LVDS output format
• Set CB coding
• Set PHI, RS, CP, SH unlock output state
Begin Scanning:
• Ensure stable INCLK applied and PLL is locked (read back Page 0, Register 0, Bit 7)
• Set Register Lock Control bit = 1
• In Master Mode, conversions will begin after the Lock Bit is set. In Slave Mode, SH_R pulses can begin after
the Lock Bit is set. SH Intervals will be generated in response to the SH_R input pulses.
• Registers and Bits marked in Boldface print may be adjusted while scanning is in progress. More major
changes (i.e.: color mode, CCDTG details) should be done by writing a 0 to the Register Lock Control Bit to
pause scanning.
92
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Registers Maps (continued)
Table 16. Register Summary Table
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 0
0
0
0
0010 0000
Main Configuration 0
0
1
1
0100 0000
Main Configuration 1
0
2
2
1100 0000
Main Configuration 2
0
3
3
1000 0010
Main Configuration 3
0
4
4
0011 0000
Main Configuration 4
0
5
5
0000 0000
Main Configuration 5
0
6
6
0000 0000
Configuration 6
0
7
7
0000 0000
Configuration 7
0
8
8
0000 0000
OSR CLAMP Start Edge
0
9
9
0001 0000
OSR CLAMP Stop Edge
0
10
A
0000 0000
OSG CLAMP Start Edge
0
11
B
0001 0000
OSG CLAMP Stop Edge
0
12
C
0000 0000
OSB CLAMP Start Edge
0
13
D
0001 0000
OSB CLAMP Stop Edge
0
14
E
0001 0110
OSR SAMPLE Start Edge
0
15
F
0010 0110
OSR SAMPLE Stop Edge
0
16
10
0001 0110
OSG SAMPLE Start Edge
0
17
11
0010 0110
OSG SAMPLE Stop Edge
0
18
12
0001 0110
OSB SAMPLE Start Edge
0
19
13
0010 0110
OSB SAMPLE Stop Edge
0
20
14
0000 0000
Sample & Clamp Monitor 0
0
21
15
0000 0000
Sample & Clamp Monitor 1
0
22 to 29
16 to 1D
0
30
1E
XX00 0011
Revision
0
31
1F
0000 0000
Page Register
Reserved
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
93
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 1
1
0
0
0000 0000
Gain Mode
1
1
1
0110 0001
Red PGA
1
2
2
0110 0001
Green PGA
1
3
3
0110 0001
Blue PGA
1
4
4
1000 0000
Red Even DAC MSB
1
5
5
0000 0000
Red Even DAC LSB
1
6
6
1000 0000
Green Even DAC MSB
1
7
7
0000 0000
Green Even DAC LSB
1
8
8
1000 0000
Blue Even DAC MSB
1
9
9
0000 0000
Blue Even DAC LSB
1
10
A
1000 0000
Red Odd DAC MSB
1
11
B
0000 0000
Red Odd DAC LSB
1
12
C
1000 0000
Green Odd DAC MSB
1
13
D
0000 0000
Green Odd DAC LSB
1
14
E
1000 0000
Blue Odd DAC MSB
1
15
F
0000 0000
Blue Odd DAC LSB
1
16
10
0100 0000
Red Even Digital Offset
1
17
11
0100 0000
Green Even Digital Offset
1
18
12
0100 0000
Blue Even Digital Offset
1
19
13
0100 0000
Red Odd Digital Offset
1
20
14
0100 0000
Green Odd Digital Offset
1
21
15
0100 0000
Blue Odd Digital Offset
1
22
16
0110 0001
Red High Gain PGA
1
23
17
0110 0001
Green High Gain PGA
1
24
18
0110 0001
Blue High Gain PGA
1
28
1C
0100 0000
Red Channel Bimodal
1
29
1D
0100 0000
Green Channel Bimodal
1
30
1E
0100 0000
Blue Channel Bimodal
1
31
1F
0000 0000
Page Register
94
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 2
2
0
0
0000 0000
Calibration Mode
2
1
1
0000 0000
Calibration # Lines
2
2
2
0001 0100
Black Cal Config
2
3
3
0100 0000
Black Target
2
4
4
0100 0011
White Cal Config
2
5
5
1000 0000
White Target
2
6
6
0000 0100
AutoCLPIN Start
2
7
7
0000 1100
AutoCLPIN End
2
8
8
0001 0000
Black Loop Start
2
9
9
0000 0000
Active/White Pixels Start - MSB
2
10
A
0001 0100
Active/White Pixels Start - LSB
2
11
B
0001 0000
Active/White Pixels End - MSB
2
12
C
0000 0000
Active/White Pixels End - LSB
2
13
D
0001 0000
Line Length MSB
2
14
E
0100 0000
Line Length LSB
2
15
F
0000 0000
Line Length Multiplier
2
16
10
0000 0000
Line Mode
2
17
11
0000 0000
SH State Length Multiplier
2
18
12
0000 0000
PHIA/B/C Delays
2
19
13
0000 0000
RS/CP Delays
2
20 to 23
14 to 17
2
24
18
1111 1000
PLL Control 1
2
25
19
0001 1000
PLL Control 2
2
26
1A
0000 0000
SSCG Control 1
2
27
1B
0000 0010
SSCG Control 2
2
28
1C
0000 0000
Clock Mult M
2
29
1D
0000 0000
Clock Mult N
2
30
1E
0000 0000
SSCG Control 3
2
31
1F
Reserved
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
95
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 3
3
0
0
0000 0000
SH State 0 Length
3
1
1
0000 0000
SH State 1 Length
3
2
2
0000 0000
SH State 2 Length
3
3
3
0000 0000
SH State 3 Length
3
4
4
0000 0000
SH State 4 Length
3
5
5
0000 0000
SH State 5 Length
3
6
6
0000 0000
SH State 6 Length
3
7
7
0000 0000
SH State 7 Length
3
8
8
0000 0000
SH State 8 Length
3
9
9
0000 0000
SH State 9 Length
3
10
A
0000 0000
SH State 10 Length
3
11
B
0000 0000
SH State 11 Length
3
12
C
0000 0000
SH State 12 Length
3
13
D
0000 0000
SH State 13 Length
3
14
E
0000 0000
SH State 14 Length
3
15
F
0000 0000
SH State 15 Length
3
16
10
0000 0000
SH State 16 Length
3
17
11
0000 0000
SH State 17 Length
3
18
12
0000 0000
SH State 18 Length
3
19
13
0000 0000
SH State 19 Length
3
20
14
0000 0000
SH State 20 Length
3
21
15
0000 0000
SH State 21 Length
3
22
16
0000 0000
SH State 22 Length
3
23
17
0000 0000
SH State 23 Length
3
24
18
0000 0000
SH State 24 Length
3
25
19
0000 0000
SH State 25 Length
3
26
1A
0000 0000
SH State 26 Length
3
27
1B
0000 0000
SH State 27 Length
3
28
1C
0000 0000
SH State 28 Length
3
29
1D
0000 0000
SH State 29 Length
3
30
1E
0000 0000
SH State 30 Length
3
31
1F
96
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 4
4
0
0
0000 0000
SH State 0 PHI, RS, CP
4
1
1
0000 0000
SH State 1 PHI, RS, CP
4
2
2
0000 0000
SH State 2 PHI, RS, CP
4
3
3
0000 0000
SH State 3 PHI, RS, CP
4
4
4
0000 0000
SH State 4 PHI, RS, CP
4
5
5
0000 0000
SH State 5 PHI, RS, CP
4
6
6
0000 0000
SH State 6 PHI, RS, CP
4
7
7
0000 0000
SH State 7 PHI, RS, CP
4
8
8
0000 0000
SH State 8 PHI, RS, CP
4
9
9
0000 0000
SH State 9 PHI, RS, CP
4
10
A
0000 0000
SH State 10 PHI, RS, CP
4
11
B
0000 0000
SH State 11 PHI, RS, CP
4
12
C
0000 0000
SH State 12 PHI, RS, CP
4
13
D
0000 0000
SH State 13 PHI, RS, CP
4
14
E
0000 0000
SH State 14 PHI, RS, CP
4
15
F
0000 0000
SH State 15 PHI, RS, CP
4
16
10
0000 0000
SH State 16 PHI, RS, CP
4
17
11
0000 0000
SH State 17 PHI, RS, CP
4
18
12
0000 0000
SH State 18 PHI, RS, CP
4
19
13
0000 0000
SH State 19 PHI, RS, CP
4
20
14
0000 0000
SH State 20 PHI, RS, CP
4
21
15
0000 0000
SH State 21 PHI, RS, CP
4
22
16
0000 0000
SH State 22 PHI, RS, CP
4
23
17
0000 0000
SH State 23 PHI, RS, CP
4
24
18
0000 0000
SH State 24 PHI, RS, CP
4
25
19
0000 0000
SH State 25 PHI, RS, CP
4
26
1A
0000 0000
SH State 26 PHI, RS, CP
4
27
1B
0000 0000
SH State 27 PHI, RS, CP
4
28
1C
0000 0000
SH State 28 PHI, RS, CP
4
29
1D
0000 0000
SH State 29 PHI, RS, CP
4
30
1E
0000 0000
SH State 30 PHI, RS, CP
4
31
1F
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
97
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 5
5
0
0
0000 0000
SH State 0 SH1-SH5
5
1
1
0000 0000
SH State 1 SH1-SH5
5
2
2
0000 0000
SH State 2 SH1-SH5
5
3
3
0000 0000
SH State 3 SH1-SH5
5
4
4
0000 0000
SH State 4 SH1-SH5
5
5
5
0000 0000
SH State 5 SH1-SH5
5
6
6
0000 0000
SH State 6 SH1-SH5
5
7
7
0000 0000
SH State 7 SH1-SH5
5
8
8
0000 0000
SH State 8 SH1-SH5
5
9
9
0000 0000
SH State 9 SH1-SH5
5
10
A
0000 0000
SH State 10 SH1-SH5
5
11
B
0000 0000
SH State 11 SH1-SH5
5
12
C
0000 0000
SH State 12 SH1-SH5
5
13
D
0000 0000
SH State 13 SH1-SH5
5
14
E
0000 0000
SH State 14 SH1-SH5
5
15
F
0000 0000
SH State 15 SH1-SH5
5
16
10
0000 0000
SH State 16 SH1-SH5
5
17
11
0000 0000
SH State 17 SH1-SH5
5
18
12
0000 0000
SH State 18 SH1-SH5
5
19
13
0000 0000
SH State 19 SH1-SH5
5
20
14
0000 0000
SH State 20 SH1-SH5
5
21
15
0000 0000
SH State 21 SH1-SH5
5
22
16
0000 0000
SH State 22 SH1-SH5
5
23
17
0000 0000
SH State 23 SH1-SH5
5
24
18
0000 0000
SH State 24 SH1-SH5
5
25
19
0000 0000
SH State 25 SH1-SH5
5
26
1A
0000 0000
SH State 26 SH1-SH5
5
27
1B
0000 0000
SH State 27 SH1-SH5
5
28
1C
0000 0000
SH State 28 SH1-SH5
5
29
1D
0000 0000
SH State 29 SH1-SH5
5
30
1E
0000 0000
SH State 30 SH1-SH5
5
31
1F
98
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 6
6
0
0
0000 0000
PHIA0
6
1
1
0000 0000
PHIA1
6
2
2
0000 0000
PHIA2
6
3
3
0000 0000
PHIA3
6
4
4
0000 0000
PHIA4
6
5
5
0000 0000
PHIA5
6
6
6
0000 0000
PHIB0
6
7
7
0000 0000
PHIB1
6
8
8
0000 0000
PHIB2
6
9
9
0000 0000
PHIB3
6
10
A
0000 0000
PHIB4
6
11
B
0000 0000
PHIB5
6
12
C
0000 0000
PHIC0
6
13
D
0000 0000
PHIC1
6
14
E
0000 0000
PHIC2
6
15
F
0000 0000
PHIC3
6
16
10
0000 0000
PHIC4
6
17
11
0000 0000
PHIC5
6
18
12
0000 0000
RS0
6
19
13
0000 0000
RS1
6
20
14
0000 0000
RS2
6
21
15
0000 0000
RS3
6
22
16
0000 0000
RS4
6
23
17
0000 0000
RS5
6
24
18
0000 0000
CP0
6
25
19
0000 0000
CP1
6
26
1A
0000 0000
CP2
6
27
1B
0000 0000
CP3
6
28
1C
0000 0000
CP4
6
29
1D
0000 0000
CP5
6
30
1E
0000 0000
HSPIX Rate Select
6
31
1F
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
99
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 7
7
0
0
0000 0000
SH1 PIXEL ON MSB
7
1
1
0000 0000
SH1 PIXEL ON LSB
7
2
2
0000 0000
SH1 PIXEL OFF MSB
7
3
3
0000 0000
SH1 PIXEL OFF LSB
7
4
4
0000 0000
SH2 PIXEL ON MSB
7
5
5
0000 0000
SH2 PIXEL ON LSB
7
6
6
0000 0000
SH2 PIXEL OFF MSB
7
7
7
0000 0000
SH2 PIXEL OFF LSB
7
8
8
0000 0000
SH3 PIXEL ON MSB
7
9
9
0000 0000
SH3 PIXEL ON LSB
7
10
A
0000 0000
SH3 PIXEL OFF MSB
7
11
B
0000 0000
SH3 PIXEL OFF LSB
7
12
C
0000 0000
SH4 PIXEL ON MSB
7
13
D
0000 0000
SH4 PIXEL ON LSB
7
14
E
0000 0000
SH4 PIXEL OFF MSB
7
15
F
0000 0000
SH4 PIXEL OFF LSB
7
16
10
0000 0000
SH5 PIXEL ON MSB
7
17
11
0000 0000
SH5 PIXEL ON LSB
7
18
12
0000 0000
SH5 PIXEL OFF MSB
7
19
13
0000 0000
SH5 PIXEL OFF LSB
7
20
14
0000 0000
PHIA Polarity Override
7
21
15
0000 0000
PHIB Polarity Override
7
22
16
0000 0000
PHIC Polarity Override
7
23
17
0000 0000
RS Polarity Override
7
24
18
0000 0000
CP Polarity Override
7
25
19
0000 0000
SH1 Polarity Override
7
26
1A
0000 0000
SH2 Polarity Override
7
27
1B
0000 0000
SH3 Polarity Override
7
28
1C
0000 0000
SH4 Polarity Override
7
29
1D
0000 0000
SH5 Polarity Override
7
30
1E
0000 0000
Reserved
7
31
1F
100
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Registers Maps (continued)
Table 16. Register Summary Table (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
REGISTER TITLE
PAGE 8
8
0
0
0000 0000
PHIA1, PHIA2 Polarity / State
8
1
1
0000 0000
PHIB1, PHIB2 Polarity / State
8
2
2
0000 0000
PHIC1, PHIC2 Polarity / State
8
3
3
0000 0000
RS, CP Polarity / State
8
4
4
0000 0000
SH1, SH2 Polarity / State
8
5
5
0000 0000
SH3, SH4 Polarity / State
8
6
6
0000 0000
SH5 Polarity / State
8
7
7
0000 0000
Reserved
8
8
8
0010 0000
LVDS Configuration
8
9
9
0000 0000
CB1/CB0 CB Mapping
8
10
A
0000 0000
CB3/CB2 CB Mapping
8
11
B
0000 0000
D2/CB4 CB Mapping
8
12
C
0000 0000
D4/D3 CB Mapping
8
13
D
0000 0000
D5 CB Mapping
8
14
E
0000 0000
Unlock State Output Values PHIA, PHIB, PHIC, RS, CP
8
15
F
0000 0000
Unlock State Output Values SH1, SH2, SH3, SH4, SH5
8
16 to 17
10 to 11
0000 0000
Reserved
8
18
12
0000 0000
Scrambler Inhibit 0 (LVDS[6:0])
8
19
13
0000 0000
Scrambler Inhibit 1 (LVDS[13:7])
8
20
14
0000 0000
Scrambler Inhibit 2 (LVDS[20:14])
8
16 to 30
15 to 1E
0000 0000
Reserved
8
31
1F
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
101
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
The following section describes all available registers in the LM98722 register bank, and their functions.
***Registers and/or Bits Marked in Boldface are Writeable when Register 0, Bit 0 = 1, all others are “Locked”.***
Table 17. Register Definition, Page 0
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0010 0000
[7]
REGISTER TITLE
REGISTER DESCRIPTION
PAGE 0
PLL Locked (READ ONLY) Status Bit
0 PLL is not locked
1 PLL is locked
[6]
Not Used
[5]
SH_R Capture Clock Select
0 Use internal CLK from XTAL source.
1 Use external INCLK source.
[4]
SH_R Capture Edge Select
0 Use rising edge of selected Clock source.
1 Use falling edge of selected Clock source.
Main
[3]
0
0
0
Configuration
Not Used
0
[2]
XTALEN
0 Use autodetecting CMOS/LVDS clock
receiver
1 Enable crystal driver. INCLK+ is output,
INCLK- is input.
[1]
Master Mode Select Bit
0 Slave/SH_R
1 Master/Line Length
[0]
Register Lock Control
0 Registers are unlocked (i.e. writeable) and
CCDTG state machines are stopped
1 Registers are locked (default) and CCDTG
state machines are operating
102
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
1
1
0100 0000
[7]
REGISTER TITLE
REGISTER DESCRIPTION
Serial Interface Mode Select
0 16+ Clock Mode [Default]
1 25+ Clock Mode
[6]
Enable PLL Range Autocalibration
0 PLL Range Autocal OFF
1 PLL Range Autocalibrates (Default)
[5]
Calibrate Gain/Offset (self clearing)
0 Calibration is off
1 Calibration is active
[4]
Main
Configuration
Software Reset - FSM
Set to 1 to reset all state machines. Self
clearing.
1
[3]
Software Reset - FSM + Registers
Set to 1 to reset all state machines and
registers. Self clearing.
[2]
Power Down CDS/SH Amplifier
[1]
Reference Buffer Power Down
[0]
Master Power Down
0 Master Power Down Disable
1 Master Power Down Enable
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
103
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
2
2
1100 0010
[7:6]
REGISTER TITLE
REGISTER DESCRIPTION
Mode Select Bits
11 Mode 3 (Default) (3 Channel Mode)
10 Mode 2 (2 Channel Mode)
01 Mode 1 (1 Channel Mode)
00 Not Used
Color Select Bits. Used to determine the inputs
sampled during a scan.
[5:4]
11 Reserved
10 Mode 2 = OSR & OSB Mode 1 = OSB
01 Mode 2 = OSG & OSB Mode 1 = OSG
00 Mode 2 = OSR & OSG Mode 1 = OSR
Color Order. Configures the sequence of the
pixel processing
[3]
0 Forward (default)
1 Reverse
Main
[2]
PIXCLK/ADCCLK Configuration. Selects
appropriate multiplier for given input clock
frequency
Configuration
Mode 3: ADC Frequency = 3x Pixel Frequency
2
Mode 2: ADC Frequency = 2x Pixel Frequency
Mode 1: ADC Frequency = 1x Pixel Frequency
0 User supplies ADC rate clock, LM98722
performs no multiplication.
1 User supplies Pixel rate clock, LM98722
performs clock multiplication.
[1]
Sampling Mode Select
0 Sample and Hold Mode
1 Correlated Double Sampling Mode (Default)
[0]
Even/Odd CCD Sensor Enable
Dedicated Even and Odd DACs and Digital
Offsets would be applied to every other pixels.
104
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
3
3
1000 0010
[7]
REGISTER TITLE
REGISTER DESCRIPTION
Source Follower Enable.
0 Disable
1 Enable (Default)
Input Bias Enable. Enables the Input Bias
Resistor ladder.
[6]
0 Disable (Default)
1 Enable
[5]
Main
Configuration
3
[4:2]
[1]
Bit CLP mode enable (black clamping done in
reference portion of every pixel of line)
0 Disabled (Default)
1 Enable
Pixel Phase Clock Select. Coarse adjustment
for Pixel phase relative to INCLK. Useful in
systems where Pixel inputs arrive with
significant delay relative to INCLK.
Sensor Polarity Select
0 Voltage increases with increasing white
level
1 Voltage decreases with increasing white
level
[0]
Reserved
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
105
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
4
4
0011 0000
[7]
Reserved
[6]
Enable VCLP Buffer
REGISTER TITLE
REGISTER DESCRIPTION
0 Use resistor divider voltages directly
1 Use buffered resistor divider voltage
[5]
Auto CLPIN Enable
0 Auto CLPIN Disabled
1 Auto CLPIN Enabled - (Default) - CLPIN
generated according to Start and End position
settings at Page 2, Registers 0x06 and 0x07
[4]
CLPIN Gating Enable
0 Auto CLPIN not gated by the SAMPLE pulse
timing
1 Auto CLPIN gated by the SAMPLE pulse timing
(Default)
[3]
Main
Configuration
4
[2:0]
VCLP Power Down
0 VCLP Normal Operation
1 No circuit is tied to the VCLP output and no
current is drawn
VCLP Voltage Setting/Source
000 0.85VA (Default)
001 0.9VA
010 0.95VA
011 0.6VA
100 0.55VA
101 0.4VA
110 0.35VA
111 0.15VA
106
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
5
5
0000 0000
[7]
REGISTER TITLE
REGISTER DESCRIPTION
Output Format
0 LVDS (Default)
1 CMOS
[6]
Output Enable. Enables the Data Output pins.
0 Disabled (Default)
1 Enable
[5]
CMOS Data CLK Override Enable
0 - SH2 output as normal
1 - CMOS Data CLK on SH2
[4:3]
Data Scrambler Enable/Mode
00 - Scrambler Disabled
01, 10, 11 - Scrambler Enabled see 1:0
description below for details:
[2:1]
Data Scrambler Submode
If Scrambler Mode = 01, Full scrambler enabled
as follows:
00 Send lvds_data[20:0]^prs[20:0]
01 Send prs[20:0]
10 Send lvds_data[20:0]^pprs[20:0]
11 Send pprs[20:0]
If Scrambler Mode = 10, 1 bit scrambler with key
of prs[0]
Main
Send lvds_data[20:0]^prs[0], with lvds_data[k] = 0
Configuration
00 k = 0 (DBO in CMOS and 714 modes, CB0 in
flexible, 16 bit mode)
5
01, txout0 disable = 0, k = 5 (DB0(lsb) in flexible,
16 bit mode)
01, txout0 disable = 1, k = 7 (DB2(lsb) in flexible,
14 bit
mode)
10 k = 16 (CB0 in 714 mode)
11 k = 20 (CB4 in 714 mode)
If Scrambler Mode = 11, 1 bit scrambler with key
of lvds_data[k].
Send lvds_data[20:0]^lvds_data[k], with
lvds_out[k] =
lvds_data[k]
00 k = 0 (DBO in CMOS and 714 modes, CB0 in
flexible, 16 bit mode)
01, txout0 disable = 0, k = 5 (DB0(lsb) in flexible,
16 bit mode)
01, txout0 disable = 1, k = 7 (DB2(lsb) in flexible,
14 bit mode)
10 k = 16 (CB0 in 714 mode)
11 k = 20 (CB4 in 714 mode)
[0]
Reserved
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
107
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
6
6
0000 0000
[7]
REGISTER TITLE
REGISTER DESCRIPTION
LVDS Test Pattern Synchronization Select
0 Synchronizes at (held at initial state during)
BOL & BOS
1 Synchronizes at (held at initial state during)
BOS
only
[6:4]
LVDS Output Pattern Select
000 Select AFE output (normal operation) (Must
be 00 for AFE Test Patterns)
001 Select 0x2A & 0x55 alternating patterns (all 3
pairs)
010 Selects 0x2A (all 3 pairs)
011 Selects 0x55 (all 3 pairs)
100 Selects 0x00 (all 4 pairs) (Differential 0 on all
outputs)
101 Selects 0x7F (all 4 pairs) (Differential 1 on all
outputs)
[3]
AFE Test Pattern - Up-count Rate Select
0 Up-count at pixel rate
Configuration
1 Up-count at BOL
6
[2:0]
Test Pattern - AFE Data Select - (Bits 6:4 must
be 000 for AFE Test Patterns)
000 Selects ADC output (normal operation)
001 Selects up-counter output
010 Selects 0xFF00 - fixed data
011 Selects 0xAA55 - fixed data
100 Selects 0x0000 - fixed data
101 Selects 0xFFFF - fixed data
110 Selects 0x00FF - fixed data
111 Selects 0x55AA - fixed data
108
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
0
7
7
0000 0000
0
8
8
0000 0000
0
9
9
0001 0000
0
10
A
0000 0000
0
11
B
0001 0000
BITS
REGISTER TITLE
Timing Generator Output Driver Strength
[5]
PHIA1, PHIA2 - 0 = Normal, 1 = High
[4]
PHIB1, PHIB2 - 0 = Normal, 1 = High
[3]
Configuration
[2]
7
[0]
SH1, SH2, SH3, SH4, SH5 - 0 = Normal, 1 =
High
[7:6]
OSR CLAMP Start
Edge
[7:6]
[7:6]
[7:6]
0
13
D
0001 0000
0
14
E
0001 0110
[7:6]
OSB CLAMP Start
Edge
15
F
0010 0110
0
16
10
0001 0110
0
17
11
0010 0110
[7:6]
OSR SAMPLE Stop
Edge
18
12
0001 0110
[7:6]
19
13
0010 0110
[7:6]
Not Used
SAMPLE_G Start Edge - Default = 22d
OSG SAMPLE Stop
Edge
Not Used
SAMPLE_G Stop Edge - Default = 38d
OSB SAMPLE Start
Edge
[5:0]
0
Not Used
SAMPLE_R Stop Edge - Default = 38d
OSG SAMPLE Start
Edge
[5:0]
0
Not Used
SAMPLE_R Start Edge - Default = 22d
[5:0]
[7:6]
Not Used
CLAMP_B Stop Edge - Default = 16d
OSR SAMPLE Start
Edge
[5:0]
[7:6]
Not Used
CLAMP_B Start Edge - Default = 0d
OSB CLAMP Stop
Edge
[5:0]
0
Not Used
CLAMP_G Stop Edge - Default = 16d
[5:0]
[7:6]
Not Used
CLAMP_G Start Edge - Default = 0d
OSG CLAMP Stop
Edge
[5:0]
[7:6]
Not Used
CLAMP_R Stop Edge - Default = 16d
OSG CLAMP Start
Edge
[5:0]
0000 0000
Not Used
CLAMP_R Start Edge - Default = 0d
OSR CLAMP Stop
Edge
[5:0]
C
RS - 0 = Normal, 1 = High
CP - 0 = Normal, 1 = High
[5:0]
12
PHIC1, PHIC2 - 0 = Normal, 1 = High
[1]
[5:0]
0
REGISTER DESCRIPTION
Not Used
SAMPLE_B Start Edge - Default = 22d
OSB SAMPLE Stop
Edge
[5:0]
Not Used
SAMPLE_B Stop Edge - Default = 38d
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
109
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
20
14
0000 0000
[7]
Not Used
[6]
SH_R Capture Monitor Override
REGISTER TITLE
REGISTER DESCRIPTION
0 SAMPB=SAMPB, CLAMPB=CLAMPB Default
1 SAMPB = INCLK, CLAMPB = SH_R
[5:3]
Selection bits for RS (user test mode)
000 Normal output
001 SAMPR Output
010 SAMPG Output
011 SAMPB Output
100 CLAMPR Output
Sample & Clamp
Monitor 0
101 CLAMPG Output
110 CLAMPB Output
111 PIXPHASE Output
[2:0]
Selection bits for CP (user test mode)
000 Normal output
001 SAMPR Output
010 SAMPG Output
011 SAMPB Output
100 CLAMPR Output
101 CLAMPG Output
110 CLAMPB Output
111 PIXPHASE Output
110
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 17. Register Definition, Page 0 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
0
21
15
0000 0000
[7:6]
Not Used
[5:3]
Selection bits for SH2 (user test mode)
REGISTER TITLE
REGISTER DESCRIPTION
000 Normal output
001 SAMPR Output
010 SAMPG Output
011 SAMPB Output
100 CLAMPR Output
101 CLAMPG Output
110 CLAMPB Output
Sample & Clamp
Monitor 1
[2:0]
111 PIXPHASE Output
Selection bits for SH3 (user test mode)
000 Normal Output
001 SAMPR Output
010 SAMPG Output
011 SAMPB Output
100 CLAMPR Output
101 CLAMPG Output
110 CLAMPB Output
111 PIXPHASE Output
0
22 to 29
16 to 1D
0000 0000
Reserved
0
30
1E
XX00 0011
[7:0]
0
31
1F
0000 0000
[3:0]
Revision
Page Register
Used to select desired page of registers being
accessed
0000 Page 0
0001 Page 1
0010 Page 2
0011 Page 3
0100 Page 4
0101 Page 5
0110 Page 6
0111 Page 7
1000 Page 8
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
111
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 18. Register Definition, Page 1
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
1
0
0
0000 0000
[7]
Gain Mode
REGISTER DESCRIPTION
CDS/SH Gain Blue - 0 = 1x Gain, 1 = 2x Gain
[6]
CDS/SH Gain Green - 0 = 1x Gain, 1 = 2x Gain
[5]
CDS/SH Gain Blue - 0 = 1x Gain, 1 = 2x Gain
[4:3]
Not used
[2]
Individual CDS/SH Gain Enable
0 Use Bit 0 for CDS/SH Gain
1 Use Bits 7:5 for CDS/SH Gains
[1]
Dual Gain Mode Enable
0 Single Gain Setting Within Each Line
1 Two Gain Settings Within Each Line
[0]
Gain Select
0 1x CDS/SH Gain - Default
1 2x CDS/SH Gain
1
1
1
0110 0001
[7:0]
Red PGA
Default = 97d for Gain = 1
1
2
2
0110 0001
[7:0]
Green PGA
Default = 97d for Gain = 1
1
3
3
0110 0001
[7:0]
Blue PGA
Default = 97d for Gain = 1
1
4
4
1000 0000
[7:0]
Red Even DAC MSB
DAC[9:2]
1
5
5
0000 0000
[7:2]
Red Even DAC LSB
Not Used
[1:0]
DAC[1:0]
1
6
6
1000 0000
[7:0]
Green Even DAC MSB DAC[9:2]
1
7
7
0000 0000
[7:2]
Green Even DAC LSB Not Used
[1:0]
DAC[1:0]
1
8
8
1000 0000
[7:0]
Blue Even DAC MSB
DAC[9:2]
1
9
9
0000 0000
[7:2]
Blue Even DAC LSB
Not Used
[1:0]
DAC[1:0]
1
10
A
1000 0000
[7:0]
Red Odd DAC MSB
DAC[9:2]
1
11
B
0000 0000
[7:2]
Red Odd DAC LSB
Not Used
[1:0]
DAC[1:0]
1
12
C
1000 0000
[7:0]
Green Odd DAC MSB
DAC[9:2]
1
13
D
0000 0000
[7:2]
Green Odd DAC LSB
Not Used
[1:0]
DAC[1:0]
1
14
E
1000 0000
[7:0]
Blue Odd DAC MSB
DAC[9:2]
1
15
F
0000 0000
[7:2]
Blue Odd DAC LSB
Not Used
1
16
10
0100 0000
[1:0]
[7]
DAC[1:0]
Red Even Digital
Offset
[6:0]
1
17
11
0100 0000
[7]
Digital Offset
Green Even Digital
Offset
[6:0]
112
Not Used
Submit Documentation Feedback
Not Used
Digital Offset
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 18. Register Definition, Page 1 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
1
18
12
0100 0000
[7]
Blue Even Digital
Offset
1
19
13
0100 0000
1
20
14
0100 0000
[6:0]
[7]
21
15
0100 0000
1
22
16
0110 0001
[7]
Not Used
Digital Offset
Blue Odd Digital
Offset
[6:0]
[7:0]
Not Used
Digital Offset
Green Odd Digital
Offset
[6:0]
1
Not Used
Digital Offset
Red Odd Digital
Offset
[6:0]
[7]
REGISTER DESCRIPTION
Not Used
Digital Offset
Red High Gain PGA
PGA setting during high gain portion of line
when dual gain mode is enabled
Default = 97d for Gain = 1
1
23
17
0110 0001
[7:0]
Green High Gain PGA PGA setting during high gain portion of line
when dual gain mode is enabled
Default = 97d for Gain = 1
1
24
18
0110 0001
[7:0]
Blue High Gain PGA
PGA setting during high gain portion of line
when dual gain mode is enabled
Default = 97d for Gain = 1
1
28
1C
0100 0000
[7]
Red Channel Bimodal Not Used
[6:0]
1
29
1D
0100 0000
[7]
Offset Binary digital Offset for Bimodal
Correction
Green Channel
Bimodal
[6:0]
1
30
1E
0100 0000
[7]
Offset Binary digital Offset for Bimodal
Correction
Blue Channel Bimodal Not Used
[6:0]
1
31
1F
0000 0000
[3:0]
Not Used
Offset Binary digital Offset for Bimodal
Correction
Page Register
Used to select desired page of registers being
accessed.
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
113
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 19. Register Definition, Page 2
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
0
0
0000 0000
[7:3]
REGISTER TITLE
REGISTER DESCRIPTION
Not Used
[2]
DDAC Disable
0 AFE output includes DDAC (digital DAC offset)
correction
1 AFE output does not include DDAC correction
Calibration
[1:0]
Mode
Calibration Mode
00 Black Calibration Only
01 White and Black Calibration - Full/Binary
White Cal
10 White and Black Calibration - Fine Tuning
11 Reserved
2
1
1
0000 0000
[7:0]
Calibration is active for this number of lines
Calibration # Lines
0 Reserved
1d to 254d sets number of lines
255d sets infinite calibration
2
2
2
0001 0100
[5:4]
DDAC Scaling
00 Linear - 1 LSB adjust
01 Scaling = 1/2
10 Scaling = 1/4
11 Scaling = 1/8
[3:2]
ADAC Scaling
00 Reserved (No scaling)
Black Cal Config
01 Scaling = 1/2
10 Scaling = 1/4
11 Scaling = 1/8
[1:0]
Number of Black Pixels
Number of pixels averaged by Black Loop
00 4 pixels
01 8 pixels
10 16 pixels
11 32 pixels
2
3
3
0100 0000
[7:0]
Black Target
Target level for Black calibration Range is 0 to
255 at 11 bit level or 0 to 8160 at 16 bit level
(default = 64 or 2048 at 16 bit level)
114
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 19. Register Definition, Page 2 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
4
4
0100 0011
[6:3]
REGISTER TITLE
REGISTER DESCRIPTION
White Loop Tolerance
White Cal success if |White Peak - White Target|
< White Loop Tolerance 0 to 15 at 10 bit level Default = 8
[2:0]
Number of White Pixels
White Cal Config
Number of White Pixels processed in moving
window average to find White Peak in line
between White Pixels Start and White Pixels End
000 4 pixels
001 8 pixels
010 16 pixels
011 32 pixels - Default
2
5
5
1000 0000
[7:0]
White Target
White Target = 768d + [7:0] at 10 bit level
White Target
Range is 768d to 1023d at 10 bit level or 49152
to 65472 at 16 bit level
(Default = 896d or 57344 at 16 bit level)
2
6
6
0000 0100
[7:0]
AutoCLPIN Start
# of pixels from SH interval End to Start of Black
Pixel Clamping (Default = 4d)
2
7
7
0000 1100
[7:0]
AutoCLPIN End
# of pixels from SH interval End to End of Black
Pixel Clamping (Default = 12d)
2
8
8
0001 0000
[7:0]
Black Loop Start
# of pixels from SH interval End to Start of Black
Loop Pixels (Default = 16d)
2
9
9
0000 0000
[7:0]
Active/White Pixels
Start - MSB
2
10
A
0001 0100
[7:0]
Active/White Pixels
Start - LSB
2
11
B
0001 0000
[7:0]
Active/White Pixels
End - MSB
2
12
C
0000 0000
[7:0]
Active/White Pixels
End - LSB
2
13
D
0001 0000
[7:0]
Line Length MSB
# of Pixel Periods between beginning of
consecutive SH Intervals (Default = 4160)
2
14
E
0100 0000
[7:0]
Line Length LSB
# of Pixel Periods between beginning of
consecutive SH Intervals
2
15
F
0000 0000
[7:2]
Not Used
[1:0]
Multiplier factor for Active/White, LSPIX ON/OFF
and
# of Pixels between SH Interval End and first
Valid Data Pixel (Default = 64d)
# of Pixels between SH Interval End and last
Valid Data Pixel (Default = 4096)
Line Length Multiplier Line Length Pixels Register Settings
00 1x
01 2x
10 4x
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
115
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 19. Register Definition, Page 2 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
16
10
0000 0000
[7]
Not Used
6:5
CIS - 2 Color Coefficient Select
REGISTER TITLE
REGISTER DESCRIPTION
Select which color PGA/DAC coefficients are
used in 2 color CIS sequences
00 Red and Green Lamp/Coefficients Used
01 Green and Blue Lamp/Coefficients Used
10 Red and Blue Lamp/Coefficients Used
11 Reserved
4:3
CCD/CIS Mode Select
00 Normal CCD Timing
01 CISa (2, 3, or 4 color sequences)
10 CISb (2 or 3 color sequences)
11 Reserved
Line Mode
[1:0]
# SH Intervals. How many different SH intervals
in a sequence of lines
00 1 SH Interval - Same SH timing every line
01 2 SH Intervals - 2 different SH interval timings
10 3 SH Intervals - 3 different SH interval timings
11 4 SH Intervals - 4 different SH interval timings
SH States are allocated as follows:
1 Interval 1 = 0 to 30
2 Interval 1 = 0 to 14, Interval 2 = 15 to 30
3 Int 1 = 0 to 9, Int 2 = 10 to 19, Int 3 = 20 to 30
4 Int 1 = 0 to 6, Int 2 = 7 to 14, Int 3 = 15 to 22,
Int 4 = 23 to 30
2
17
11
0000 0000
[7:3]
Not Used
[2:0]
SH State Length values are multiplied by this
factor
SH State Length
000 SH Timings x1
Multiplier
001 SH Timings x2
010 SH Timings x4
011 SH Timings x8
100 SH Timings x16
101 to 111 Reserved
116
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 19. Register Definition, Page 2 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
18
12
0000 0000
[7:6]
REGISTER TITLE
REGISTER DESCRIPTION
Not Used
[5]
PHIA On Delay
0 Normal
1 PHIA begins 1 pixel period late
[4]
PHIA Off Delay
0 Normal
1 PHIA stops 1 pixel period late
[3]
PHIB On Delay
0 Normal
1 PHIB begins 1 pixel period late
PHIA/B/C Delays
[2]
PHIB Off Delay
0 Normal
1 PHIB stops 1 pixel period late
[1]
PHIC On Delay
0 Normal
1 PHIC begins 1 pixel period late
[0]
PHIC Off Delay
0 Normal
1 PHIC stops 1 pixel period late
2
19
13
0000 0000
[7:4]
Not Used
[3]
RS On Delay
0 Normal
1 RS begins 1 pixel period late
[2]
RS Off Delay
0 Normal
RS/CP Delays
[1]
1 RS stops 1 pixel period late
CP On Delay
0 Normal
1 CP begins 1 pixel period late
[0]
CP Off Delay
0 Normal
1 CP stops 1 pixel period late
2
20 to 23
14 to 17
2
24
18
Reserved
1111 1000
[7:5]
Master PLL Range Setting for PLL1 and PLL2
when Autorange is off. Set to 111.
[4:3]
PLL1 Charge Pump Current Control
PLL Control 1
[2:0]
Default = 11
PLL1 Filter Bandwidth Control
Default = 000
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
117
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 19. Register Definition, Page 2 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
25
19
0001 1000
[7:5]
REGISTER TITLE
REGISTER DESCRIPTION
Reserved
Default = 000
[4:3]
PLL2 Charge Pump Current Control
Default = 11
PLL Control 2
[2:0]
Set to 00 when using SSCG.
PLL2 Filter Bandwidth Control
Default = 000
Set to 111 when using SSCG.
2
26
1A
0000 0000
[7:6]
Spread Rate Multiplier
(Increases modulation frequency in low pixel
frequency applications)
00 1x - Default
01 2x
10 4x (Page 2, Register D,E max = 32,768)
11 Reserved
[5]
SSCG Spread Boost
0 Normal, PLL divide step is 1/28
1 Boost, PLL divide step is 1/56. Narrower and
cleaner spread for 1ch and 2ch modes, but limits
max pixel freq to 25 MHz.
[4]
SSCG Spread Gain
0 Spread widths as specified in [3:2]
1 Spread widths are 2x [3:2] settings
[3:2]
SSCG Spread Width (Fmod = Fcenter+/Width/2)
SSCG Control 1
00 5%
01 2.5%
10 1.25%
11 0.625%
[1]
SSCG SH Sync Enable
0 Spread unsynched, once SSCG Enable is set,
SSCG wil begin immediately.
1 Spread synched to SH interval, once SSCG
Enable
is set, the SSCG will begin at the first SH
Interval.
[0]
SSCG Enable
0 Spread Disabled
1 Spread Enabled
118
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 19. Register Definition, Page 2 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
27
1B
0000 0010
[7]
REGISTER TITLE
REGISTER DESCRIPTION
Load SSCG state machine
(SSCG Enable 0->1 also performs this function)
0 Normal
1 Load state machine (self clearing)
[6]
FIFO Reset at SH_R
0 FIFO is only reset when SSCG started
1 FIFO is reset at SH_R. Only useful in Slave
Mode with Spread LVDS Only set. Ensures that
FIFO counters are centered if SH_R period is
consistenly shorter or longer than Line Length
settings.
[5]
Spread Waveform Reset at SH_R
0 Spread waveform not reset by SH_R
1 Spread waveform reset by SH_R
[4]
SSCG Control 2
Override PLL2 Lock Detector
0 PLL2 Lock Detector Normal
1 Force PLL2 Lock Detect = 1. Set to 1 when
using SSCG.
[3]
Override PLL1 Lock Detector
0 PLL1 Lock Detector Normal
1 Force PLL1 Lock Detect = 1. Useful only if
using a large multiplication factor and a lot of jitter
is present in the source clock.
[2]
Spread MaxRate
0 Spread Normal
1 Force Spreading to highest modulation
frequency instead of tied to Line Length Setting.
[1:0]
PLL Mode Select
11 Spread All System Clocks, No Multiplication
10 PLLs and SSCG Disabled - Default
01 Spread All System Clocks, Multiplication
Enabled
00 Spread Output Clocks Only, Multiplication
Enabled
2
28
1C
0000 0000
Clock Mult M
Multiplying PLL. Fout = Fin x M/N M =
mmmmmmmm + 1 (1 to 256)
2
29
1D
0000 0000
Clock Mult N
Multiplying PLL. Fout = Fin x M/N N = nnnnnnnn
+ 1 (1 to 256)
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
119
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 19. Register Definition, Page 2 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
2
30
1E
0000 0000
[7]
REGISTER TITLE
REGISTER DESCRIPTION
FIFO Reset
0 FIFO normal operating
1 Force reset of FIFO (self clearing)
SSCG Control 3
[6:0]
FIFO and Spread Waveform SH_R Reset Holdoff
Delay reset of FIFO and Spread Waveform from
0 to 127 ADC clock cycles after the internal
synchronized SH_R. To allow this event to occur
during SH Interval after all valid pixels in the
pipeline have been processed.
2
120
31
1F
[3:0]
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 20. Register Definition, Page 3
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
3
0
0
0000 0000
[7:0]
SH State 0
Length
Sets length of this SH interval state
3
1
1
0000 0000
[7:0]
SH State 1
Length
Sets length of this SH interval state
3
2
2
0000 0000
[7:0]
SH State 2
Length
Sets length of this SH interval state
3
3
3
0000 0000
[7:0]
SH State 3
Length
Sets length of this SH interval state
3
4
4
0000 0000
[7:0]
SH State 4
Length
Sets length of this SH interval state
3
5
5
0000 0000
[7:0]
SH State 5
Length
Sets length of this SH interval state
3
6
6
0000 0000
[7:0]
SH State 6
Length
Sets length of this SH interval state
3
7
7
0000 0000
[7:0]
SH State 7
Sets length of this SH interval state
3
8
8
0000 0000
[7:0]
SH State 8
REGISTER DESCRIPTION
Length
Sets length of this SH interval state
Length
3
9
9
0000 0000
[7:0]
SH State 9
3
10
A
0000 0000
[7:0]
SH State 10
3
11
B
0000 0000
[7:0]
SH State 11
Sets length of this SH interval state
Length
Sets length of this SH interval state
Length
Sets length of this SH interval state
Length
3
12
C
0000 0000
[7:0]
SH State 12
Length
Sets length of this SH interval state
3
13
D
0000 0000
[7:0]
SH State 13
Length
Sets length of this SH interval state
3
14
E
0000 0000
[7:0]
SH State14
Length
Sets length of this SH interval state
3
15
F
0000 0000
[7:0]
SH State 15
Length
Sets length of this SH interval state
3
16
10
0000 0000
[7:0]
SH State 16
Length
Sets length of this SH interval state
3
17
11
0000 0000
[7:0]
SH State 17
Length
Sets length of this SH interval state
3
18
12
0000 0000
[7:0]
SH State 18
Length
Sets length of this SH interval state
3
19
13
0000 0000
[7:0]
SH State 19
Length
Sets length of this SH interval state
3
20
14
0000 0000
[7:0]
SH State 20
Length
Sets length of this SH interval state
3
21
15
0000 0000
[7:0]
SH State 21
Length
Sets length of this SH interval state
3
22
16
0000 0000
[7:0]
SH State 22
Length
Sets length of this SH interval state
3
23
17
0000 0000
[7:0]
SH State 23
Length
Sets length of this SH interval state
3
24
18
0000 0000
[7:0]
SH State 24
Length
Sets length of this SH interval state
3
25
19
0000 0000
[7:0]
SH State 25
Length
Sets length of this SH interval state
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
121
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 20. Register Definition, Page 3 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
3
26
1A
0000 0000
[7:0]
SH State 26
Length
Sets length of this SH interval state
3
27
1B
0000 0000
[7:0]
SH State 27
Length
Sets length of this SH interval state
3
28
1C
0000 0000
[7:0]
SH State 28
Length
Sets length of this SH interval state
3
29
1D
0000 0000
[7:0]
SH State 29
Length
Sets length of this SH interval state
3
30
1E
0000 0000
[7:0]
SH State 30
Length
Sets length of this SH interval state
3
31
1F
[3:0]
Page Register
122
Submit Documentation Feedback
REGISTER DESCRIPTION
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 21. Register Definitions, Page 4
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
REGISTER DESCRIPTION
4
0
0
0000 0000
[7]
SH State 0
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this
SH interval state
RS 0 = Low, 1 = High 1 0 = Low, 1 = High
[6]
CP 0 = Low, 1 = High
[5]
PHIA2 0 = Low, 1 = High
[4]
PHIA1 0 = Low, 1 = High
[3]
PHIB2 0 = Low, 1 = High
[2]
PHIB1 0 = Low, 1 = High
[1]
PHIC2 0 = Low, 1 = High
[0]
PHIC1 0 = Low, 1 = High
4
1
1
0000 0000
[7:0]
SH State 1
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
2
2
0000 0000
[7:0]
SH State 2
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
3
3
0000 0000
[7:0]
SH State 3
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
4
4
0000 0000
[7:0]
SH State 4
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
5
5
0000 0000
[7:0]
SH State 5
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
6
6
0000 0000
[7:0]
SH State 6
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
7
7
0000 0000
[7:0]
SH State 7
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
8
8
0000 0000
[7:0]
SH State 8
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
9
9
0000 0000
[7:0]
SH State 9
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
10
A
0000 0000
[7:0]
SH State 10
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
11
B
0000 0000
[7:0]
SH State 11
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
12
C
0000 0000
[7:0]
SH State 12
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
13
D
0000 0000
[7:0]
SH State 13
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
14
E
0000 0000
[7:0]
SH State 14
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
15
F
0000 0000
[7:0]
SH State 15
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
16
10
0000 0000
[7:0]
SH State 16
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
17
11
0000 0000
[7:0]
SH State 17
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
18
12
0000 0000
[7:0]
SH State 18
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
19
13
0000 0000
[7:0]
SH State 19
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
123
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 21. Register Definitions, Page 4 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
REGISTER DESCRIPTION
4
20
14
0000 0000
[7:0]
SH State 20
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
21
15
0000 0000
[7:0]
SH State 21
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
22
16
0000 0000
[7:0]
SH State 22
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
23
17
0000 0000
[7:0]
SH State 23
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
24
18
0000 0000
[7:0]
SH State 24
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
25
19
0000 0000
[7:0]
SH State 25
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
26
1A
0000 0000
[7:0]
SH State 26
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
27
1B
0000 0000
[7:0]
SH State 27
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
28
1C
0000 0000
[7:0]
SH State 28
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
29
1D
0000 0000
[7:0]
SH State 29
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
30
1E
0000 0000
[7:0]
SH State 30
PHI, RS, CP
Controls whether these outputs are 1 or 0 during
this SH interval state
4
31
1F
[3:0]
Page Register
124
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 22. Register Definitions, Page 5
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
5
0
0
0000 0000
[7:5]
SH State 0
SH1-SH5
REGISTER DESCRIPTION
Not Used
Controls whether these outputs are 1 or 0 during
this SH interval state
[4]
SH5 0 = Low, 1 = High
[3]
SH4 0 = Low, 1 = High
[2]
SH3 0 = Low, 1 = High
[1]
SH2 0 = Low, 1 = High
[0]
SH1 0 = Low, 1 = High
5
1
1
0000 0000
[4:0]
SH State 1
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
2
2
0000 0000
[4:0]
SH State 2
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
3
3
0000 0000
[4:0]
SH State 3
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
4
4
0000 0000
[4:0]
SH State 4
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
5
5
0000 0000
[4:0]
SH State 5
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
6
6
0000 0000
[4:0]
SH State 6
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
7
7
0000 0000
[4:0]
SH State 7
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
8
8
0000 0000
[4:0]
SH State 8
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
9
9
0000 0000
[4:0]
SH State 9
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
10
A
0000 0000
[4:0]
SH State 10
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
11
B
0000 0000
[4:0]
SH State 11
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
12
C
0000 0000
[4:0]
SH State 12
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
13
D
0000 0000
[4:0]
SH State 13
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
14
E
0000 0000
[4:0]
SH State 14
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
15
F
0000 0000
[4:0]
SH State 15
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
16
10
0000 0000
[4:0]
SH State 16
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
17
11
0000 0000
[4:0]
SH State 17
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
18
12
0000 0000
[4:0]
SH State 18
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
19
13
0000 0000
[4:0]
SH State 19
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
20
14
0000 0000
[4:0]
SH State 20
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
21
15
0000 0000
[4:0]
SH State 21
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
22
16
0000 0000
[4:0]
SH State 22
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
23
17
0000 0000
[4:0]
SH State 23
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
125
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 22. Register Definitions, Page 5 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER TITLE
REGISTER DESCRIPTION
5
24
18
0000 0000
[4:0]
SH State 24
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
25
19
0000 0000
[4:0]
SH State 25
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
26
1A
0000 0000
[4:0]
SH State 26
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
27
1B
0000 0000
[4:0]
SH State 27
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
28
1C
0000 0000
[4:0]
SH State 28
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
29
1D
0000 0000
[4:0]
SH State 29
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
30
1E
0000 0000
[4:0]
SH State 30
SH1-SH5
Controls whether these outputs are 1 or 0 during
this SH interval state
5
31
1F
[3:0]
Page Register
126
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 23. Register Tables Page 6
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
6
0
0
0000 0000
[1:0]
PHIA0
Upper 2 MSb (first shifted out of HSTG)
6
1
1
0000 0000
[7:0]
PHIA1
Next 8
6
2
2
0000 0000
[7:0]
PHIA2
Next 8
6
3
3
0000 0000
[7:0]
PHIA3
Next 8
6
4
4
0000 0000
[7:0]
PHIA4
Next 8
6
5
5
0000 0000
[7:0]
PHIA5
Lower 8 LSb (last shifted out of HSTG)
6
6
6
0000 0000
[1:0]
PHIB0
Upper 2 MSb (first shifted out of HSTG)
6
7
7
0000 0000
[7:0]
PHIB1
Next 8
6
8
8
0000 0000
[7:0]
PHIB2
Next 8
6
9
9
0000 0000
[7:0]
PHIB3
Next 8
6
10
A
0000 0000
[7:0]
PHIB4
Next 8
6
11
B
0000 0000
[7:0]
PHIB5
Lower 8 LSb (last shifted out of HSTG)
6
12
C
0000 0000
[1:0]
PHIC0
Upper 2 MSb (first shifted out of HSTG)
6
13
D
0000 0000
[7:0]
PHIC1
Next 8
6
14
E
0000 0000
[7:0]
PHIC2
Next 8
6
15
F
0000 0000
[7:0]
PHIC3
Next 8
6
16
10
0000 0000
[7:0]
PHIC4
Next 8
6
17
11
0000 0000
[7:0]
PHIC5
Lower 8 LSb (last shifted out of HSTG)
6
18
12
0000 0000
[1:0]
RS0
Upper 2 MSb (first shifted out of HSTG)
6
19
13
0000 0000
[7:0]
RS1
Next 8
6
20
14
0000 0000
[7:0]
RS2
Next 8
6
21
15
0000 0000
[7:0]
RS3
Next 8
6
22
16
0000 0000
[7:0]
RS4
Next 8
6
23
17
0000 0000
[7:0]
RS5
Lower 8 LSb (last shifted out of HSTG)
6
24
18
0000 0000
[1:0]
CP0
Upper 2 MSb (first shifted out of HSTG)
6
25
19
0000 0000
[7:0]
CP1
Next 8
6
26
1A
0000 0000
[7:0]
CP2
Next 8
6
27
1B
0000 0000
[7:0]
CP3
Next 8
6
28
1C
0000 0000
[7:0]
CP4
Next 8
6
29
1D
0000 0000
[7:0]
CP5
Lower 8 LSb (last shifted out of HSTG)
6
30
1E
0000 0000
[7:5]
Not Used
Allows high speed generators to operate at 1/2
normal rate. So the full sequence will be clocked
out over 2 pixels instead of 1 pixel
[4]
[3]
HSPIX Rate
Select
31
1F
Rate PHIB 0 = Normal Rate, 1 = 1/2
[2]
Rate PHIC 0 = Normal Rate, 1 = 1/2
[1]
Rate RS 0 = Normal Rate, 1 = 1/2
[0]
6
PHIA 0 = Normal Rate, 1 = 1/2
[3:0]
Rate CP 0 = Normal Rate, 1 = 1/2 Rate
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
127
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 24. Register Tables Page 7
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
7
0
0
0000 0000
[7:0]
SH1
PIXEL ON
MSB
MSB of Pixel count where this signal goes low to
high Range is 0 to 65535
7
1
1
0000 0000
[7:0]
SH1
PIXEL ON
LSB
LSB of Pixel count where this signal goes low to
high
7
2
2
0000 0000
[7:0]
SH1
PIXEL OFF
MSB
MSB of Pixel count where this signal goes high to
low Range is 0 to 65535
7
3
3
0000 0000
[7:0]
SH1
PIXEL OFF
LSB
LSB of Pixel count where this signal goes high to
low
7
4
4
0000 0000
[7:0]
SH2
PIXEL ON
MSB
MSB of Pixel count where this signal goes low to
high Range is 0 to 65535
7
5
5
0000 0000
[7:0]
SH2
PIXEL ON
LSB
LSB of Pixel count where this signal goes low to
high
7
6
6
0000 0000
[7:0]
SH2
PIXEL OFF
MSB
MSB of Pixel count where this signal goes high to
low Range is 0 to 65535
7
7
7
0000 0000
[7:0]
SH2
PIXEL OFF
LSB
LSB of Pixel count where this signal goes high to
low
7
8
8
0000 0000
[7:0]
SH3
PIXEL ON
MSB
MSB of Pixel count where this signal goes low to
high Range is 0 to 65535
7
9
9
0000 0000
[7:0]
SH3
PIXEL ON
LSB
LSB of Pixel count where this signal goes low to
high
7
10
A
0000 0000
[7:0]
SH3
PIXEL OFF
MSB
MSB of Pixel count where this signal goes high to
low Range is 0 to 65535
7
11
B
0000 0000
[7:0]
SH3
PIXEL OFF
LSB
LSB of Pixel count where this signal goes high to
low
7
12
C
0000 0000
[7:0]
SH4
PIXEL ON
MSB
MSB of Pixel count where this signal goes low to
high Range is 0 to 65535
7
13
D
0000 0000
[7:0]
SH4
PIXEL ON
LSB
LSB of Pixel count where this signal goes low to
high
7
14
E
0000 0000
[7:0]
SH4
PIXEL OFF
MSB
MSB of Pixel count where this signal goes high to
low Range is 0 to 65535
7
15
F
0000 0000
[7:0]
SH4
PIXEL OFF
LSB
LSB of Pixel count where this signal goes high to
low
7
16
10
0000 0000
[7:0]
SH5
PIXEL ON
MSB
MSB of Pixel count where this signal goes low to
high Range is 0 to 65535
7
17
11
0000 0000
[7:0]
SH5
PIXEL ON
LSB
LSB of Pixel count where this signal goes low to
high
7
18
12
0000 0000
[7:0]
SH5
PIXEL OFF
MSB
MSB of Pixel count where this signal goes high to
low Range is 0 to 65535
128
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 24. Register Tables Page 7 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
7
19
13
0000 0000
[7:0]
SH5
PIXEL OFF
LSB
LSB of Pixel count where this signal goes high to
low
7
20
14
0000 0000
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
PHIA Polarity
1 Signal Inverted
Override
7
21
15
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
PHIB Polarity
[2]
7
22
16
0000 0000
Override
1 Signal Inverted
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
PHIC Polarity
1 Signal Inverted
Override
7
23
17
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
RS Polarity
1 Signal Inverted
Override
7
24
18
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
CP Polarity
1 Signal Inverted
Override
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
129
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 24. Register Tables Page 7 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
7
25
19
0000 0000
[7:4]
REGISTER
TITLE
REGISTER
DESCRIPTION
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
SH1 Polarity
1 Signal Inverted
Override
7
26
1A
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
SH2 Polarity
1 Signal Inverted
Override
7
27
1B
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
SH3 Polarity
1 Signal Inverted
Override
7
28
1C
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
SH4 Polarity
1 Signal Inverted
Override
7
29
1D
0000 0000
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
Polarity Override Line 0
[7:4]
Not Used
[3]
Polarity Override Line 3
0 Signal Not Inverted
SH5 Polarity
1 Signal Inverted
Override
[2]
Polarity Override Line 2
[1]
Polarity Override Line 1
[0]
130
7
30
1E
7
31
1F
0000 0000
Polarity Override Line 0
Reserved
[3:0]
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 25. Register Definition, Page 8
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
8
0
0
0000 0000
[7]
Not Used
[6]
PHIA1 Active (0 = Tristate, 1* = Active)
[5]
PHIA1 Source (0* = Timing, 1 = DC logic 1)
[4]
REGISTER
TITLE
PHIA1,
REGISTER
DESCRIPTION
PHIA1 Polarity (0* = Not Inverted, 1 = Inverted)
PHIA2,
[3]
Polarity /
Not Used
State
8
1
1
0000 0000
[2]
PHIA2 Active (0 = Tristate, 1* = Active)
[1]
PHIA2 Source (0* = Timing, 1 = DC logic 1)
[0]
PHIA2 Polarity (0* = Not Inverted, 1 = Inverted)
[7]
Not Used
[6]
PHIB1 Active (0 = Tristate, 1* = Active) PHIB1
[5]
Source (0* = Timing, 1 = DC logic 1) PHIB1
[4]
PHIB1,
Polarity (0* = Not Inverted, 1 = Inverted)
PHIB2,
[3]
Polarity /
Not Used
State
8
2
2
0000 0000
[2]
PHIB2 Active (0 = Tristate, 1* = Active)
[1]
PHIB2 Source (0* = Timing, 1 = DC logic 1)
[0]
PHIB2 Polarity (0* = Not Inverted, 1 = Inverted)
[7]
Not Used
[6]
PHIC1 Active (0 = Tristate, 1* = Active)
[5]
PHIC1 Source (0* = Timing, 1 = DC logic 1)
[4]
PHIC1
PHIC1 Polarity (0* = Not Inverted, 1 = Inverted)
PHIC2
[3]
Polarity /
Not Used
State
[2]
PHIC2 Active (0 = Tristate, 1* = Active)
[1]
PHIC2 Source (0* = Timing, 1 = DC logic 1)
[0]
PHIC2 Polarity (0* = Not Inverted, 1 = Inverted)
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
131
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
REGISTER
TITLE
8
3
3
0000 0000
[7]
Not Used
[6]
RS Active (0 = Tristate, 1* = Active)
[5]
RS Source (0* = Timing, 1 = DC logic 1)
[4]
REGISTER
DESCRIPTION
RS Polarity (0* = Not Inverted, 1 = Inverted)
RS, CP
[3]
Polarity /
Not Used
State
8
4
4
0000 0000
[2]
CP Active (0 = Tristate, 1* = Active)
[1]
CP Source (0* = Timing, 1 = DC logic 1)
[0]
CP Polarity (0* = Not Inverted, 1 = Inverted)
[7]
Not Used
[6]
SH1 Active (0 = Tristate, 1* = Active)
[5]
SH1 Source (0* = Timing, 1 = DC logic 1)
[4]
SH1, SH2
SH1 Polarity (0* = Not Inverted, 1 = Inverted)
Polarity /
[3]
8
5
5
0000 0000
State
Not Used
[2]
SH2 Active (0 = Tristate, 1* = Active)
[1]
SH2 Source (0* = Timing, 1 = DC logic 1)
[0]
SH2 Polarity (0* = Not Inverted, 1 = Inverted)
[7]
Not Used
[6]
SH3 Active (0 = Tristate, 1* = Active)
[5]
SH3 Source (0* = Timing, 1 = DC logic 1)
[4]
SH3, SH4
SH3 Polarity (0* = Not Inverted, 1 = Inverted)
Polarity /
[3]
132
State
Not Used
[2]
SH4 Active (0 = Tristate, 1* = Active)
[1]
SH4 Source (0* = Timing, 1 = DC logic 1)
[0]
SH4 Polarity (0* = Not Inverted, 1 = Inverted)
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
BITS
8
6
6
0000 0000
[7]
REGISTER
TITLE
REGISTER
DESCRIPTION
Not Used
[6]
SH5 Active (0 = Tristate, 1* = Active)
SH5
[5]
Polarity /
SH5 Source (0* = Timing, 1 = DC logic 1)
State
[4]
SH5 Polarity (0* = Not Inverted, 1 = Inverted)
[3:0]
8
7
7
0000 0000
[7:0]
8
8
8
0010 0000
[7]
Not Used
Reserved
LVDS TXCLK Disable
0 LVDS TXCLK Enabled - Default
1 LVDS TXCLK Disabled
[6]
CMOS CLKOUT Disable
0 CMOS CLKOUT Enabled - Default
1 CMOS CLKOUT Disabled
[5:4]
LVDS Drive Adjust
00 Reduce 100 mV
01 Reduce 50 mV
10 Default
11 Increase 50 mV
[3]
LVDS
Configuration
LVDS TXCLK Delay
0 TXCLK timing normal
1 TXCLK delayed
[2]
BOL CB Bit Latency
0 Normal Compensation
1 No latency compensation
[1]
LVDS Disable TXOUT0
0 TXOUT0 LVDS Pair Enabled
1 TXOUT0 LVDS Pair Disabled
[0]
LVDS Mode Select
0 LM98714
1 Flexible CB Mapping
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
133
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
9
9
0000 0000
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
Selects CB Bit Mapping
[7:4]
CB1 Mapping
0000 CBO1 from LM98714 definition
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
CB1/CB0 CB
Mapping
[3:0]
CB0 Mapping
0000 CBO0 from LM98714 definition
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
134
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
10
A
0000 0000
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
Selects CB Bit Mapping
[7:4]
CB3 Mapping
0000 CBO30 from LM98714 definition
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
CB3/CB2 CB
Mapping
[3:0]
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
CB2 Mapping
0000 CBO2 from LM98714 definition
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
135
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
11
B
0000 0000
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
Selects CB Bit Mapping
[7:4]
D2 Mapping
0000 D2 (Normal output for particular bit position)
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
D2/CB4 CB
Mapping
[3:0]
1110 Active White Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
CB4 Mapping
0000 CBO4 from LM98714 definition
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
136
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
12
C
0000 0000
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
Selects CB Bit Mapping
[7:4]
D4 Mapping
0000 D4 (Normal output for particular bit position)
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
D4/D3 CB
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
Mapping
[3:0]
D3 Mapping
0000 D4 (Normal output for particular bit position)
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
137
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
13
D
0000 0000
BITS
REGISTER
TITLE
[7:4]
REGISTER
DESCRIPTION
Not Used
Selects CB Bit Mapping
[3:0]
D5 Mapping
0000 D5 (Normal output for particular bit position)
0001 CBO0 from LM98714 definition
0010 CBO1 from LM98714 definition
0011 CBO2 from LM98714 definition
0100 CBO3 from LM98714 definition
0101 CBO4 from LM98714 definition
0110 R - High for a red channel pixel
0111 G - High for a green channel pixel
D5 CB
Mapping
1000 B - High for a blue channel pixel
1001 Parity - 21 bit if TXOUT0 enabled, 14 bit if
TXOUT0 disabled
1010 Ping - High for pixels processed by the Ping
section of a channel, low for Pong
1011 Line#lsb - Line = 0 to 3 for lines 0 to 3 in
multiline sequences
1100 Line#msb
1101 Black Loop Pixels - High for pixels
processed by the Black Loop
1110 ActiveWhite Loop Pixels - High for pixels
processed by the White Loop
1111 CLP Pixels - High for pixels where the input
CLP switch is closed
138
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
14
E
0000 0000
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
Select level of CLK outputs during register
updating (UNLOCK state)
These can be modified during LOCK state to
allow user to set up chip for what happens during
the next UNLOCK state
[7]
PHIA1 Unlock State
0 = Low, 1 = High
[6]
PHIA2 Unlock State
0 = Low, 1 = High
[5]
Unlock State
Output Values
PHIB1 Unlock State
0 = Low, 1 = High
PHIA, PHIB,
[4]
PHIC, RS, CP
PHIB2 Unlock State
0 = Low, 1 = High
[3]
PHIC1 Unlock State
0 = Low, 1 = High
[2]
PHIC2 Unlock State
0 = Low, 1 = High
[1]
RS Unlock State
0 = Low, 1 = High
[0]
CP Unlock State
0 = Low, 1 = High
8
15
F
0000 0000
[7:5]
Not Used
Select level of CLK outputs during register
updating (UNLOCK state)
These can be modified during LOCK state to
allow user to set up chip for what happens during
the next UNLOCK state
[4]
SH1 Unlock State
Unlock State
0 = Low, 1 = High
Output Values
[3]
SH1, SH2,
SH2 Unlock State
SH3, SH4, SH5
0 = Low, 1 = High
[2]
SH3 Unlock State
0 = Low, 1 = High
[1]
SH4 Unlock State
0 = Low, 1 = High
[0]
SH5 Unlock State
0 = Low, 1 = High
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
139
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
Table 25. Register Definition, Page 8 (continued)
PAGE
(dec)
ADDR
(dec)
ADDR
(hex)
DEFAULT
(binary)
8
16 to 17
10 to 11
0000 0000
8
18
12
0000 0000
BITS
REGISTER
TITLE
REGISTER
DESCRIPTION
Reserved
[7]
Reserved
Inhibit Scrambling Individual LVDS Bits if 1.
[6]
8
19
13
0000 0000
Do Not Scramble LVDS[6]
[5]
Scrambler
Do Not Scramble LVDS[5]
[4]
Inhibit 0
Do Not Scramble LVDS[4]
[3]
Do Not Scramble LVDS[3]
[2]
Do Not Scramble LVDS[2]
[1]
Do Not Scramble LVDS[1]
[0]
Do Not Scramble LVDS[0]
[7]
Reserved
Inhibit Scrambling Individual LVDS Bits if 1.
[6]
8
20
14
0000 0000
Do Not Scramble LVDS[13]
[5]
Scrambler
Do Not Scramble LVDS[12]
[4]
Inhibit 1
Do Not Scramble LVDS[11]
[3]
Do Not Scramble LVDS[10]
[2]
Do Not Scramble LVDS[9]
[1]
Do Not Scramble LVDS[8]
[0]
Do Not Scramble LVDS[7]
[7]
Reserved
Inhibit Scrambling Individual LVDS Bits if 1.
[6]
Do Not Scramble LVDS[20]
[5]
Scrambler
Do Not Scramble LVDS[19]
[4]
Inhibit 2
Do Not Scramble LVDS[18]
[3]
Do Not Scramble LVDS[17]
[2]
Do Not Scramble LVDS[16]
[1]
Do Not Scramble LVDS[15]
[0]
140
8
21 to 30
15 to 1E
8
31
1F
0000 0000
Do Not Scramble LVDS[14]
Reserved
[3:0]
Page Register
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
LM98722
www.ti.com
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
8 Layout
8.1 Layout Example
U1A
74AC04/SO
TP1
R1 150
2
1
1
U1B
TEST POINT
TP2
74AC04/SO
R2 4.7
U1C
4
74AC04/SO
3
1
TEST POINT
R3 4.7
6
5
U1D
74AC04/SO
R4 4.7
8
9
TP3
U1E
74AC04/SO
1
R5 10
10
TEST POINT
11
U1F
74AC04/SO
R6 10
12
13
U2A
74AC04/SO
R7 10
2
1
U2B
74AC04/SO
U3
R8 4.7
U2C
U5
12
13
14
15
16
17
18
19
20
21
22
+12V
C1
47uF/25V
U7
4
74AC04/SO
3
1
2
3
R10 4.7
PHI-TG2
PHI-TG1
PHI-1
PHI-2
NC
PHI-2
NC
PHI-SEL
V0D
VOUT1
VOUT2
GND
PHI-TG3
PHI-2
PHI-1
NC
NC
PHI-1
PHI-CLB
PHI-R
GND
VOUT3
11
10
9
8
7
6
5
4
3
2
1
6
5
U2D
8
CE
CAL
RESET#
SH_R
9
74AC04/SO
R13 47
10
11
U2F
SDIO
SCLK
SEN#
74AC04/SO
R14 47
12
13
12
13
14
15
16
17
18
19
20
21
VA
C2
0.1u
VREFB
VREFT
TP4
R18
100
R20
Q1
2SC945
100
C4
Q2
R21 2SC945
100
C5
47uF/25V
Q3
R22 2SC945
100
R24
2k
C6
tbd
C7
tbd
C8
tbd
22
23
24
25
26
27
28
VC
VD
DGND
VA
AGND
VA
VREFB
VREFT
VA
AGND
VCLP
VA
IBIAS
D0_TXOUT0D1_TXOUT0+
D2_TXOUT1D3_TXOUT1+
D4_TXOUT2D5_TXOUT2+
D6_TXCLKD7_TXCLK+
AGND
OSr
AGND
OSg
AGND
OSb
CPOFILT2
INCLKINCLK+
DVB
CPOFILT1
DGND
56
55
54
53
52
51
50
49
48
47
46
45
9
10
11
14
44
43
42
Pin 15
Pin 18
VA
VA
VC
VD
15
41
40
39
38
37
36
35
34
16
C14
0.1uF
Pin 21
17
22
33
32
31
30
29
12
20
7
13
18
19
21
C10
0.1uF
Pin 44
VD
C15
0.1uF
RXCLKIN-
R16
100
RXCLKIN+
PDN
LVDSVCC
PLLVCC
LVDSGND
LVDSGND
LVDSGND
PLLGND
PLLGND
RXCLKOUT
24
26
27
29
30
31
33
34
35
37
39
40
41
43
45
46
47
1
2
4
5
23
INCLKINCLK+
VA
C15
0.1uF
RXIN2+
RXOUT0
RXOUT1
RXOUT2
RXOUT3
RXOUT4
RXOUT5
RXOUT6
RXOUT7
RXOUT8
RXOUT9
RXOUT10
RXOUT11
RXOUT12
RXOUT13
RXOUT14
RXOUT15
RXOUT16
RXOUT17
RXOUT18
RXOUT19
RXOUT20
0.1
VREFB
C13
0.1uF
RXIN1+
RXIN2-
R15
100
R26
100
VA
RXIN0+
RXIN1-
R12
100
TP5 TP6 TP7
Pin 12
DS90CR218A/SO
RXIN0-
R9
100
VC
C20
R25
2k
1
R23
2k
R19
100
47uF/25V
VCLP
1
CE
CAL
RESET
SH_R
SDI
SDO
SCLK
SEN
1
C3
47uF/25V
R27
9.0k 1%
1
R17
100
4
5
6
7
8
9
10
11
8
SH5
SH4
PHIB2
PHIB1
VC
DGND
PHIA2
PHIA1
CP
RS
SH3
CLKOUT/SH2
74AC04/SO
R11 4.7
U2E
LM98722
PHIC2
PHIC1
SH1
C16
0.1uF
VREFT
Pin 52
VC
VCLP
C17
0.1uF
C18
0.1uF
C11
4.7uF
C19
0.1uF
J1
Install 100 Ohm for LVDS INCLK.
Install solder jumper for CMOS
INCLK
C12
0.1uF
Figure 65. Example Application Circuit
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
141
LM98722
SNAS487B – SEPTEMBER 2009 – REVISED MARCH 2015
www.ti.com
9 Device and Documentation Support
9.1 Device Support
For additional information, see Texas Instruments' E2E community resources: http://e2e.ti.com.
9.2 Trademarks
All trademarks are the property of their respective owners.
9.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
9.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
10 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
142
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LM98722
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
(3)
Device Marking
(4/5)
(6)
LM98722CCMT/NOPB
ACTIVE
TSSOP
DGG
56
34
RoHS & Green
SN
Level-2-260C-1 YEAR
0 to 70
LM98722CCMT
LM98722CCMTX/NOPB
ACTIVE
TSSOP
DGG
56
1000
RoHS & Green
SN
Level-2-260C-1 YEAR
0 to 70
LM98722CCMT
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
