LMC6001BIH

National Semiconductor is now part of Texas Instruments. Search http://www.ti.com/ for the latest technical information and details on our current products and services. LMC6001 Ultra Ultra-Low Input Current Amplifier General Description Featuring 100% tested input currents of 25 fA max., low operating power, and ESD protection of 2000V, the LMC6001 achieves a new industry benchmark for low input current operational amplifiers. By tightly controlling the molding compound, National is able to offer this ultra-low input current in a lower cost molded package. To avoid long turn-on settling times common in other low input current opamps, the LMC6001A is tested 3 times in the first minute of operation. Even units that meet the 25 fA limit are rejected if they drift. Because of the ultra-low input current noise of 0.13 fA/√Hz, the LMC6001 can provide almost noiseless amplification of high resistance signal sources. Adding only 1 dB at 100 kΩ, 0.1 dB at 1 MΩ and 0.01 dB or less from 10 MΩ to 2,000 MΩ, the LMC6001 is an almost noiseless amplifier. The LMC6001 is ideally suited for electrometer applications requiring ultra-low input leakage such as sensitive photodetection transimpedance amplifiers and sensor amplifiers. Since input referred noise is only 22 nV/√Hz, the LMC6001 can achieve higher signal to noise ratio than JFET input type electrometer amplifiers. Other applications of the LMC6001 include long interval integrators, ultra-high input impedance instrumentation amplifiers, and sensitive electrical-field measurement circuits. Features (Max limit, 25°C unless otherwise noted) ■ Input current (100% tested): 25 fA ■ Input current over temp.: 2 pA ■ Low power: 750 μA ■ Low VOS: 350 μV ■ Low noise: 22 nV/√Hz @1 kHz Typ. Applications ■ ■ ■ ■ Electrometer amplifier Photodiode preamplifier Ion detector A.T.E. leakage testing Connection Diagrams 8-Pin DIP 8-Pin Metal Can 1188701 Top View 1188702 Top View Ordering Information Package Industrial Temperature Range −40°C to +85°C NSC Package Drawing 8-Pin Molded DIP LMC6001AIN, LMC6001BIN, LMC6001CIN N08E 8-Pin Metal Can LMC6001AIH, LMC6001BIH H08C © 2009 National Semiconductor Corporation 11887 www.national.com LMC6001 Ultra Ultra-Low Input Current Amplifier November 4, 2009 LMC6001 Absolute Maximum Ratings (Note 1) Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Differential Input Voltage Voltage at Input/Output Pin Supply Voltage (V+ − V−) Output Short Circuit to V+ Output Short Circuit to V− Lead Temperature (Soldering, 10 Sec.) Storage Temperature Junction Temperature Current at Input Pin Current at Output Pin Current at Power Supply Pin Power Dissipation ESD Tolerance (Note 9) (Note 1) Temperature Range LMC6001AI, LMC6001BI, LMC6001CI −40°C ≤ TJ ≤ +85°C Supply Voltage ±Supply Voltage (V+) + 0.3V, (V−) − 0.3V 4.5V ≤ V+ ≤ 15.5V Thermal Resistance (Note 11) −0.3V to +16V (Note 2, Note 10) (Note 2) 260°C −65°C to +150°C 150°C ±10 mA ±30 mA 40 mA (Note 9) 2 kV  θJA, N Package 100°C/W  θJA, H Package 145°C/W  θJC, H Package Power Dissipation 45°C/W (Note 8) DC Electrical Characteristics Limits in standard typeface guaranteed for TJ = 25°C and limits in boldface type apply at the temperature extremes. Unless otherwise specified, V+ = 5V, V− = 0V, VCM = 1.5V, and RL > 1M. Symbol IB Conditions Parameter Input Current Typical (Note 4) Either Input, VCM = 0V, Input Offset Current VOS Input Offset Voltage 5 25 100 1000 4000 4000 1000 2000 2000 0.35 1.0 1.0 1.0 1.7 2.0 0.7 1.35 1.35 1.35 2.0 10 10 75 72 66 72 68 63 73 66 66 70 63 63 80 74 74 77 71 71 VS = ±5V, VCM = 0V TCVOS Input Offset Units 2000 10 VS = ±5V IOS Limits (Note 5) LMC6001AI LMC6001BI LMC6001CI 2.5 fA mV μV/°C Voltage Drift RIN Input Resistance CMRR Common Mode 0V ≤ VCM ≤ 7.5V Rejection Ratio V+ = 10V Positive Power Supply 5V ≤ V+ ≤ 15V +PSRR Tera Ω >1 83 83 Rejection Ratio −PSRR Negative Power 0V ≥ V− ≥ −10V 94 Supply Rejection Ratio AV Large Signal Sourcing, RL = 2 kΩ 400 300 300 Voltage Gain (Note 6) 300 200 200 Sinking, RL = 2 kΩ 350 180 90 90 100 60 60 −0.4 −0.1 −0.1 −0.1 V 0 0 0 max V+ − 1.9 V+ − 2.3 V+ − 2.3 V+ − 2.3 V V+ V+ V+ 1400 (Note 6) VCM dB min Input Common-Mode V+ = 5V and 15V Voltage For CMRR ≥ 60 dB www.national.com 2 − 2.5 − 2.5 − 2.5 V/mV min min VO Conditions Parameter Output Swing Typical (Note 4) V+ = 5V 4.75 4.75 V 4.67 4.67 min 0.10 0.14 0.17 0.20 0.24 0.20 0.24 V max 14.63 14.50 14.37 14.37 V 14.34 14.25 14.25 min 0.26 0.35 0.45 0.44 0.56 0.44 0.56 V max 22 16 13 13 10 8 8 16 13 13 13 10 10 28 23 23 RL = 2 kΩ to 7.5V Output Current Sourcing, V+ = 5V, VO = 0V Sinking, V+ = 5V, 21 VO = 5V Sourcing, V+ = 15V, 30 VO = 0V IS Supply Current LMC6001AI LMC6001BI LMC6001CI 4.73 RL = 2 kΩ to 2.5V IO Units 4.80 4.87 V+ = 15V Limits (Note 5) 22 18 18 Sinking, V+ = 15V, VO = 13V (Note 10) 34 28 22 23 18 23 18 V+ = 5V, VO = 1.5V 450 750 750 750 900 900 900 850 850 850 950 950 950 V+ = 15V, VO = 7.5V 550 3 mA min μA max www.national.com LMC6001 Symbol LMC6001 AC Electrical Characteristics Limits in standard typeface guaranteed for TJ = 25°C and limits in boldface type apply at the temperature extremes. Unless otherwise specified, V+ = 5V, V− = 0V, VCM = 1.5V and RL > 1M. Symbol SR Parameter Slew Rate Limits (Note 5) Typical Conditions (Note 7) Units (Note 4) LM6001AI LM6001BI LM6001CI 1.5 0.8 0.8 0.8 0.6 0.6 0.6 V/μs min GBW Gain-Bandwidth Product 1.3 MHz φfm Phase Margin 50 Deg GM Gain Margin 17 dB en Input-Referred Voltage Noise F = 1 kHz 22 nV/√Hz in Input-Referred Current Noise F = 1 kHz 0.13 fA/√Hz THD Total Harmonic Distortion F = 10 kHz, AV = −10, 0.01 % RL = 100 kΩ, VO = 8 VPP Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30 mA over long term may adversely affect reliability. Note 3: The maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max) − TA)/θJA. Note 4: Typical values represent the most likely parametric norm. Note 5: All limits are guaranteed by testing or statistical analysis. Note 6: V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V ≤ VO ≤ 11.5V. For Sinking tests, 2.5V ≤ VO ≤ 7.5V. Note 7: V+ = 15V. Connected as Voltage Follower with 10V step input. Limit specified is the lower of the positive and negative slew rates. Note 8: For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD = (TJ − TA)/θJA. Note 9: Human body model, 1.5 kΩ in series with 100 pF. Note 10: Do not connect the output to V+, when V+ is greater than 13V or reliability will be adversely affected. Note 11: All numbers apply for packages soldered directly into a printed circuit board. www.national.com 4 LMC6001 Typical Performance Characteristics VS = ±7.5V, TA = 25°C, unless otherwise specified Input Current vs. Temperature Input Current vs. VCM VS = ±5V 1188716 1188717 Supply Current vs. Supply Voltage Input Voltage vs.Output Voltage 1188718 1188719 Common Mode Rejection Ratio vs. Frequency Power Supply Rejection Ratio vs. Frequency 1188721 1188720 5 www.national.com LMC6001 Input Voltage Noise vs. Frequency Noise Figure vs. Source Resistance 1188722 1188723 Output Characteristics Sourcing Current Output Characteristics Sinking Current 1188724 1188725 Gain and Phase Response vs. Temperature (−55°C to +125°C) Gain and Phase Response vs. Capacitive Load with RL = 500 kΩ 1188726 www.national.com 1188727 6 Inverting Small Signal Pulse Response 1188729 1188728 Inverting Large Signal Pulse Response Non-Inverting Small Signal Pulse Response 1188730 1188731 Non-Inverting Large Signal Pulse Response Stability vs. Capacitive Load 1188732 1188733 7 www.national.com LMC6001 Open Loop Frequency Response LMC6001 dominant pole is affected by the resistive load on the amplifier. Capacitive load driving capability can be optimized by using an appropriate resistive load in parallel with the capacitive load (see Typical Curves). Direct capacitive loading will reduce the phase margin of many op-amps. A pole in the feedback loop is created by the combination of the op-amp's output impedance and the capacitive load. This pole induces phase lag at the unity-gain crossover frequency of the amplifier resulting in either an oscillatory or underdamped pulse response. With a few external components, op amps can easily indirectly drive capacitive loads, as shown in Figure 2. Applications Hints AMPLIFIER TOPOLOGY The LMC6001 incorporates a novel op-amp design topology that enables it to maintain rail-to-rail output swing even when driving a large load. Instead of relying on a push-pull unity gain output buffer stage, the output stage is taken directly from the internal integrator, which provides both low output impedance and large gain. Special feed-forward compensation design techniques are incorporated to maintain stability over a wider range of operating conditions than traditional opamps. These features make the LMC6001 both easier to design with, and provide higher speed than products typically found in this low power class. COMPENSATING FOR INPUT CAPACITANCE It is quite common to use large values of feedback resistance for amplifiers with ultra-low input current, like the LMC6001. Although the LMC6001 is highly stable over a wide range of operating conditions, certain precautions must be met to achieve the desired pulse response when a large feedback resistor is used. Large feedback resistors with even small values of input capacitance, due to transducers, photodiodes, and circuit board parasitics, reduce phase margins. When high input impedances are demanded, guarding of the LMC6001 is suggested. Guarding input lines will not only reduce leakage, but lowers stray input capacitance as well. (See Printed-Circuit-Board Layout for High Impedance Work). The effect of input capacitance can be compensated for by adding a capacitor, Cf, around the feedback resistors (as in Figure 1) such that: 1188706 FIGURE 2. LMC6001 Noninverting Gain of 10 Amplifier, Compensated to Handle Capacitive Loads In the circuit of Figure 2, R1 and C1 serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Capacitive load driving capability is enhanced by using a pullup resistor to V+ (Figure 3). Typically a pullup resistor conducting 500 μA or more will significantly improve capacitive load responses. The value of the pullup resistor must be determined based on the current sinking capability of the amplifier with respect to the desired output swing. Open loop gain of the amplifier can also be affected by the pullup resistor (see Electrical Characteristics). or R1 CIN ≤ R2 Cf Since it is often difficult to know the exact value of CIN, Cf can be experimentally adjusted so that the desired pulse response is achieved. Refer to the LMC660 and LMC662 for a more detailed discussion on compensating for input capacitance. 1188705 1188707 FIGURE 1. Cancelling the Effect of Input Capacitance FIGURE 3. Compensating for Large Capacitive Loads with a Pullup Resistor CAPACITIVE LOAD TOLERANCE All rail-to-rail output swing operational amplifiers have voltage gain in the output stage. A compensation capacitor is normally included in this integrator stage. The frequency location of the www.national.com 8 LMC6001 PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the LMC6001, typically less than 10 fA, it is essential to have an excellent layout. Fortunately, the techniques of obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6001's inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc., connected to the op-amp's inputs, as in Figure 4. To have a significant effect, guard rings should be placed on both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012Ω, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of the input. This would cause a 500 times degradation from the LMC6001's actual performance. If a guard ring is used and held within 1 mV of the inputs, then the same resistance of 1012Ω will only cause 10 fA of leakage current. Even this small amount of leakage will degrade the extremely low input current performance of the LMC6001. See Figure 5 for typical connections of guard rings for standard op-amp configurations. 1188710 Non-Inverting Amplifier 1188711 Follower FIGURE 5. Typical Connections of Guard Rings The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 6. 1188712 (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board). 1188708 FIGURE 6. Air Wiring FIGURE 4. Examples of Guard Ring in PC Board Layout Another potential source of leakage that might be overlooked is the device package. When the LMC6001 is manufactured, the device is always handled with conductive finger cots. This is to assure that salts and skin oils do not cause leakage paths on the surface of the package. We recommend that these same precautions be adhered to, during all phases of inspection, test and assembly. LATCHUP CMOS devices tend to be susceptible to latchup due to their internal parasitic SCR effects. The (I/O) input and output pins look similar to the gate of the SCR. There is a minimum current required to trigger the SCR gate lead. The LMC6001 is designed to withstand 100 mA surge current on the I/O pins. Some resistive method should be used to isolate any capacitance from supplying excess current to the I/O pins. In addition, like an SCR, there is a minimum holding current for any 1188709 Inverting Amplifier 9 www.national.com LMC6001 latchup mode. Limiting current to the supply pins will also inhibit latchup susceptibility. micropower LMC6041 provides phase inversion and offset so that the output is directly proportional to pH, over the full range of the probe. The pH reading can now be directly displayed on a low cost, low power digital panel meter. Total current consumption will be about 1 mA for the whole system. The micropower dual operational amplifier, LMC6042, would optimize power consumption but not offer these advantages: 1. The LMC6001A guarantees a 25 fA limit on input current at 25°C. 2. The input ESD protection diodes in the LMC6042 are only rated at 500V while the LMC6001 has much more robust protection that is rated at 2000V. The setup and calibration is simple with no interactions to cause problems. 1. Disconnect the pH probe and with R3 set to about midrange and the noninverting input of the LMC6001 grounded, adjust R8 until the output is 700 mV. 2. Apply −414.1 mV to the noninverting input of the LMC6001. Adjust R3 for and output of 1400 mV. This completes the calibration. As real pH probes may not perform exactly to theory, minor gain and offset adjustments should be made by trimming while measuring a precision buffer solution. Typical Applications The extremely high input resistance, and low power consumption, of the LMC6001 make it ideal for applications that require battery-powered instrumentation amplifiers. Examples of these types of applications are hand-held pH probes, analytic medical instruments, electrostatic field detectors and gas chromotographs. TWO OPAMP, TEMPERATURE COMPENSATED pH PROBE AMPLIFIER The signal from a pH probe has a typical resistance between 10 MΩ and 1000 MΩ. Because of this high value, it is very important that the amplifier input currents be as small as possible. The LMC6001 with less than 25 fA input current is an ideal choice for this application. The theoretical output of the standard Ag/AgCl pH probe is 59.16 mV/pH at 25°C with 0V out at a pH of 7.00. This output is proportional to absolute temperature. To compensate for this, a temperature compensating resistor, R1, is placed in the feedback loop. This cancels the temperature dependence of the probe. This resistor must be mounted where it will be at the same temperature as the liquid being measured. The LMC6001 amplifies the probe output providing a scaled voltage of ±100 mV/pH from a pH of 7. The second opamp, a 1188715 R1 100k + 3500 ppm/°C (Note 12) R2 68.1k R3, 8 5k R4, 9 100k R5 36.5k R6 619k R7 97.6k D1 LM4040D1Z-2.5 C1 2.2 μF Note 12: (Micro-ohm style 137 or similar) FIGURE 7. pH Probe Amplifier 20 fA and offset drift is less than 2.5 μV/°C. R2 provides a simple means of adjusting gain over a wide range without degrading CMRR. R7 is an initial trim used to maximize CMRR without using super precision matched resistors. For good CMRR over temperature, low drift resistors should be used. ULTRA-LOW INPUT CURRENT INSTRUMENTATION AMPLIFIER Figure 8 shows an instrumentation amplifier that features high differential and common mode input resistance (>1014Ω), 0.01% gain accuracy at AV = 1000, excellent CMRR with 1 MΩ imbalance in source resistance. Input current is less than www.national.com 10 LMC6001 1188713 If R1 = R5, R3 = R6, and R4 = R7; then   ∴AV ≈ 100 for circuit shown (R2 = 9.85k). FIGURE 8. Instrumentation Amplifier 11 www.national.com LMC6001 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin Metal Can Package (H) NS Package Number H08C 8-Pin Molded Dual-In-Line Package NS Package Number N08E www.national.com 12 LMC6001 Notes 13 www.national.com LMC6001 Ultra Ultra-Low Input Current Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Solutions www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com