0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LMC660AIMX/NOPB

LMC660AIMX/NOPB

  • 厂商:

    BURR-BROWN(德州仪器)

  • 封装:

    SOIC14_150MIL

  • 描述:

    IC OPAMP GP 4 CIRCUIT 14SOIC

  • 数据手册
  • 价格&库存
LMC660AIMX/NOPB 数据手册
LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 LMC660 CMOS Quad Operational Amplifier Check for Samples: LMC660 FEATURES DESCRIPTION • • • • • • • • • • • The LMC660 CMOS Quad operational amplifier is ideal for operation from a single supply. It operates from +5V to +15.5V and features rail-to-rail output swing in addition to an input common-mode range that includes ground. Performance limitations that have plagued CMOS amplifiers in the past are not a problem with this design. Input VOS, drift, and broadband noise as well as voltage gain into realistic loads (2 kΩ and 600Ω) are all equal to or better than widely accepted bipolar equivalents. 1 2 Rail-to-Rail Output Swing Specified for 2 kΩ and 600Ω Loads High Voltage Gain: 126 dB Low Input Offset Voltage: 3 mV Low Offset Voltage Drift: 1.3 μV/°C Ultra Low Input Bias Current: 2 fA Input Common-Mode Range Includes V− Operating Range from +5V to +15.5V Supply ISS = 375 μA/Amplifier; Independent of V+ Low Distortion: 0.01% at 10 kHz Slew Rate: 1.1 V/μs This chip is built with TI's advanced Double-Poly Silicon-Gate CMOS process. See the LMC662 datasheet for a dual CMOS operational amplifier with these same features. APPLICATIONS • • • • • • • • High-Impedance Buffer or Preamplifier Precision Current-to-Voltage Converter Long-Term Integrator Sample-and-Hold Circuit Peak Detector Medical Instrumentation Industrial Controls Automotive Sensors Connection Diagrams Figure 1. 14-Pin SOIC/PDIP Figure 2. LMC660 Circuit Topology (Each Amplifier) 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1998–2013, Texas Instruments Incorporated LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) Differential Input Voltage ±Supply Voltage Supply Voltage 16V Output Short Circuit to V+ See (2) Output Short Circuit to V− See (3) Lead Temperature (Soldering, 10 sec.) 260°C −65°C to +150°C Storage Temp. Range (V+) + 0.3V, (V−) − 0.3V Voltage at Input/Output Pins Current at Output Pin ±18 mA Current at Input Pin ±5 mA Current at Power Supply Pin 35 mA Power Dissipation See (4) Junction Temperature 150°C ESD tolerance (5) 1000V (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Do not connect output to V+ when V+ is greater than 13V or reliability may be adversely affected. Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature and/or multiple Op Amp shorts can result in exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30 mA over long term may adversely affect reliability. The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) − TA)/θJA. Human Body Model is 1.5 kΩ in series with 100 pF. Operating Ratings Temperature Range LMC660AI −40°C ≤ TJ ≤ +85°C LMC660C 0°C ≤ TJ ≤ +70°C Supply Voltage Range 4.75V to 15.5V See (1) Power Dissipation Thermal Resistance (θJA) (2) (1) (2) 2 14-Pin SOIC 115°C/W 14-Pin PDIP 85°C/W For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD = (TJ − TA)/θJA. All numbers apply for packages soldered directly into a PC board. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 DC Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25°C. Boldface limits apply at the temperature extremes. V+ = 5V, V− = 0V, VCM = 1.5V, VO = 2.5V and RL > 1MΩ unless otherwise specified. Parameter Test Conditions Input Offset Voltage Typ (1) LMC660AI Limit (1) 1 LMC660C Limit (1) Units 3 6 mV 3.3 6.3 max 1.3 μV/°C Input Bias Current 0.002 pA Input Offset Current 0.001 Input Offset Voltage Average Drift Input Resistance 4 2 max 2 1 max 70 63 dB 68 62 min 70 63 dB 68 62 min 84 74 dB 83 73 min −0.1 −0.1 V 0 0 max V+ − 2.3 V+ − 2.3 V pA >1 Common Mode 0V ≤ VCM ≤ 12.0V Rejection Ratio V+ = 15V Positive Power Supply 5V ≤ V+ ≤ 15V Rejection Ratio VO = 2.5V Negative Power Supply 0V ≤ V− ≤ −10V TeraΩ 83 83 94 Rejection Ratio Input Common-Mode V+ = 5V & 15V Voltage Range For CMRR ≥ 50 dB −0.4 V+ − 1.9 + Large Signal Voltage Gain Output Swing V − 2.5 V − 2.4 min RL = 2 kΩ (2) Sourcing Sinking 2000 440 400 300 200 V/mV min 500 180 120 90 80 V/mV min RL = 600Ω (2) Sourcing Sinking 1000 220 200 150 100 V/mV min 250 100 60 50 40 V/mV min V+ = 5V 4.87 4.82 4.78 V 4.79 4.76 min 0.15 0.19 V 0.17 0.21 max 4.41 4.27 V 4.31 4.21 min 0.50 0.63 V 0.56 0.69 max 14.50 14.37 V 14.44 14.32 min 0.35 0.44 V 0.40 0.48 max 13.35 12.92 V 13.15 12.76 min 1.16 1.45 V 1.32 1.58 max RL = 2 kΩ to V+/2 0.10 V+ = 5V 4.61 + RL = 600Ω to V /2 0.30 V+ = 15V 14.63 RL = 2 kΩ to V+/2 0.26 V+ = 15V 13.90 RL = 600Ω to V+/2 0.79 (1) (2) + Typical values represent the most likely parametric norm. Limits are specified by testing or correlation. V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V ≤ VO ≤ 11.5V. For Sinking tests, 2.5V ≤ VO ≤ 7.5V. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 3 LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com DC Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for TJ = 25°C. Boldface limits apply at the temperature extremes. V+ = 5V, V− = 0V, VCM = 1.5V, VO = 2.5V and RL > 1MΩ unless otherwise specified. Parameter Output Current Test Conditions Sourcing, VO = 0V Typ (1) LMC660AI Limit (1) LMC660C Limit (1) 22 16 13 mA 14 11 min 16 13 mA 14 11 min 28 23 mA 25 21 min 23 mA min V+ = 5V Sinking, VO = 5V Output Current Sourcing, VO = 0V 21 40 V+ = 15V Supply Current Sinking, VO = 13V (3) 39 28 24 20 All Four Amplifiers 1.5 2.2 2.7 mA 2.6 2.9 max VO = 1.5V (3) Units Do not connect output to V+ when V+ is greater than 13V or reliability may be adversely affected. AC Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25°C. Boldface limits apply at the temperature extremes. V+ = 5V, V− = 0V, VCM = 1.5V, VO = 2.5V and RL > 1MΩ unless otherwise specified. Parameter Slew Rate Test Conditions See (2) Typ (1) LMC660AI Limit (1) LMC660C Limit (1) Units 1.1 0.8 0.8 V/μs 0.6 0.7 min Gain-Bandwidth Product 1.4 MHz Phase Margin 50 Deg 17 dB Gain Margin Amp-to-Amp Isolation See (3) 130 dB Input Referred Voltage Noise F = 1 kHz 22 nV/√Hz Input Referred Current Noise f = 1 kHz 0.0002 pA//√Hz Total Harmonic Distortion f = 10 kHz, AV = −10 RL = 2 kΩ, VO = 8 VPP V+ = 15V 0.01 % (1) (2) (3) 4 Typical values represent the most likely parametric norm. Limits are specified by testing or correlation. V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates. Input referred. V+ = 15V and RL = 10 kΩ connected to V+/2. Each amp excited in turn with 1 kHz to produce VO = 13 VPP. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 Typical Performance Characteristics VS = ±7.5V, TA = 25°C unless otherwise specified. Supply Current vs. Supply Voltage Offset Voltage Figure 3. Figure 4. Input Bias Current Output Characteristics Current Sinking Figure 5. Figure 6. Output Characteristics Current Sourcing Input Voltage Noise vs. Frequency Figure 7. Figure 8. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 5 LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VS = ±7.5V, TA = 25°C unless otherwise specified. 6 CMRR vs. Frequency Open-Loop Frequency Response Figure 9. Figure 10. Frequency Response vs. Capacitive Load Non-Inverting Large Signal Pulse Response Figure 11. Figure 12. Stability vs. Capacitive Load Stability vs. Capacitive Load Figure 13. Figure 14. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 APPLICATION INFORMATION AMPLIFIER TOPOLOGY The topology chosen for the LMC660, shown in Figure 15, is unconventional (compared to general-purpose op amps) in that the traditional unity-gain buffer output stage is not used; instead, the output is taken directly from the output of the integrator, to allow rail-to-rail output swing. Since the buffer traditionally delivers the power to the load, while maintaining high op amp gain and stability, and must withstand shorts to either rail, these tasks now fall to the integrator. As a result of these demands, the integrator is a compound affair with an embedded gain stage that is doubly fed forward (via Cf and Cff) by a dedicated unity-gain compensation driver. In addition, the output portion of the integrator is a push-pull configuration for delivering heavy loads. While sinking current the whole amplifier path consists of three gain stages with one stage fed forward, whereas while sourcing the path contains four gain stages with two fed forward. Figure 15. LMC660 Circuit Topology (Each Amplifier) The large signal voltage gain while sourcing is comparable to traditional bipolar op amps, even with a 600Ω load. The gain while sinking is higher than most CMOS op amps, due to the additional gain stage; however, under heavy load (600Ω) the gain will be reduced as indicated in DC Electrical Characteristics. Avoid resistive loads of less than 500Ω, as they may cause instability. COMPENSATING INPUT CAPACITANCE The high input resistance of the LMC660 op amps allows the use of large feedback and source resistor values without losing gain accuracy due to loading. However, the circuit will be especially sensitive to its layout when these large-value resistors are used. Every amplifier has some capacitance between each input and AC ground, and also some differential capacitance between the inputs. When the feedback network around an amplifier is resistive, this input capacitance (along with any additional capacitance due to circuit board traces, the socket, etc.) and the feedback resistors create a pole in the feedback path. In the following General Operational Amplifier circuit, Figure 16 the frequency of this pole is: (1) where CS is the total capacitance at the inverting input, including amplifier input capacitance and any stray capacitance from the IC socket (if one is used), circuit board traces, etc., and RP is the parallel combination of RF and RIN. This formula, as well as all formulae derived below, apply to inverting and non-inverting op amp configurations. When the feedback resistors are smaller than a few kΩ, the frequency of the feedback pole will be quite high, since CS is generally less than 10 pF. If the frequency of the feedback pole is much higher than the “ideal” closed-loop bandwidth (the nominal closed-loop bandwidth in the absence of CS), the pole will have a negligible effect on stability, as it will add only a small amount of phase shift. However, if the feedback pole is less than approximately 6 to 10 times the “ideal” −3 dB frequency, a feedback capacitor, CF, should be connected between the output and the inverting input of the op amp. This condition can also be stated in terms of the amplifier's low-frequency noise gain: To maintain stability a feedback capacitor will probably be needed if: Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 7 LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com (2) where: (3) is the amplifier's low-frequency noise gain and GBW is the amplifier's gain bandwidth product. An amplifier's lowfrequency noise gain is represented by the formula: (4) regardless of whether the amplifier is being used in inverting or non-inverting mode. Note that a feedback capacitor is more likely to be needed when the noise gain is low and/or the feedback resistor is large. If the above condition is met (indicating a feedback capacitor will probably be needed), and the noise gain is large enough that: (5) the following value of feedback capacitor is recommended: (6) If (7) the feedback capacitor should be: (8) Note that these capacitor values are usually significant smaller than those given by the older, more conservative formula: (9) CS consists of the amplifier's input capacitance plus any stray capacitance from the circuit board and socket. CF compensates for the pole caused by CS and the feedback resistors. Figure 16. General Operational Amplifier Circuit Using the smaller capacitors will give much higher bandwidth with little degradation of transient response. It may be necessary in any of the above cases to use a somewhat larger feedback capacitor to allow for unexpected stray capacitance, or to tolerate additional phase shifts in the loop, or excessive capacitive load, or to decrease the noise or bandwidth, or simply because the particular circuit implementation needs more feedback capacitance to be sufficiently stable. For example, a printed circuit board's stray capacitance may be larger or smaller than the breadboard's, so the actual optimum value for CF may be different from the one estimated using the breadboard. In most cases, the values of CF should be checked on the actual circuit, starting with the computed value. 8 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 CAPACITIVE LOAD TOLERANCE Like many other op amps, the LMC660 may oscillate when its applied load appears capacitive. The threshold of oscillation varies both with load and circuit gain. The configuration most sensitive to oscillation is a unity-gain follower. See Typical Performance Characteristics. The load capacitance interacts with the op amp's output resistance to create an additional pole. If this pole frequency is sufficiently low, it will degrade the op amp's phase margin so that the amplifier is no longer stable at low gains. As shown in Figure 17, the addition of a small resistor (50Ω to 100Ω) in series with the op amp's output, and a capacitor (5 pF to 10 pF) from inverting input to output pins, returns the phase margin to a safe value without interfering with lower-frequency circuit operation. Thus larger values of capacitance can be tolerated without oscillation. Note that in all cases, the output will ring heavily when the load capacitance is near the threshold for oscillation. Figure 17. Rx, Cx Improve Capacitive Load Tolerance Capacitive load driving capability is enhanced by using a pull up resistor to V+ (Figure 18). Typically a pull up resistor conducting 500 μA or more will significantly improve capacitive load responses. The value of the pull up resistor must be determined based on the current sinking capability of the amplifier with respect to the desired output swing. Open loop gain of the amplifier can also be affected by the pull up resistor (see DC Electrical Characteristics). Figure 18. Compensating for Large Capacitive Loads with a Pull Up Resistor PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the LMC662, typically less than 0.04 pA, it is essential to have an excellent layout. Fortunately, the techniques for obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC660's inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op amp's inputs. See Figure 19. To have a significant effect, guard rings should be placed on both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012Ω, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of an input. This would cause a 100 times degradation from the LMC660's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a resistance of 1011Ω would cause only 0.05 pA of leakage current, or perhaps a minor (2:1) degradation of the amplifier's performance. See Figure 20a, Figure 20b, and Figure 20c for typical connections of guard rings for standard op amp configurations. If both inputs are active and at high impedance, the guard can be tied to ground and still provide some protection; see Figure 20d. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 9 LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com Figure 19. Example, using the LMC660, of Guard Ring in P.C. Board Layout (a) Inverting Amplifier (b) Non-Inverting Amplifier (c) Follower (d) Howland Current Pump Figure 20. Guard Ring Connections 10 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 21. (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board.) Figure 21. Air Wiring BIAS CURRENT TESTING The test method of Figure 21 is appropriate for bench-testing bias current with reasonable accuracy. To understand its operation, first close switch S2 momentarily. When S2 is opened, then: (10) Figure 22. Simple Input Bias Current Test Circuit A suitable capacitor for C2 would be a 5 pF or 10 pF silver mica, NPO ceramic, or air-dielectric. When determining the magnitude of Ib−, the leakage of the capacitor and socket must be taken into account. Switch S2 should be left shorted most of the time, or else the dielectric absorption of the capacitor C2 could cause errors. Similarly, if S1 is shorted momentarily (while leaving S2 shorted): (11) where Cx is the stray capacitance at the + input. Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 11 LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com TYPICAL SINGLE-SUPPLY APPLICATIONS (V+ = 5.0 VDC) Additional single-supply applications ideas can be found in the LM324 datasheet. The LMC660 is pin-for-pin compatible with the LM324 and offers greater bandwidth and input resistance over the LM324. These features will improve the performance of many existing single-supply applications. Note, however, that the supply voltage range of the LMC660 is smaller than that of the LM324. Figure 23. Low-Leakage Sample-and-Hold Figure 24. Instrumentation Amplifier If R1 = R5, R3 = R6, and R4 = R7; then (12) ∴ AV ≈100 for circuit shown. For good CMRR over temperature, low drift resistors should be used. Matching of R3 to R6 and R4 to R7 affect CMRR. Gain may be adjusted through R2. CMRR may be adjusted through R7. Figure 25. Sine-Wave Oscillator Oscillator frequency is determined by R1, R2, C1, and C2: 12 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 TYPICAL SINGLE-SUPPLY APPLICATIONS (continued) + (V = 5.0 VDC) fosc = 1/2πRC, where R = R1 = R2 and C = C1 = C2. This circuit, as shown, oscillates at 2.0 kHz with a peak-to-peak output swing of 4.5V. Figure 26. 1 Hz Square-Wave Oscillator Figure 27. Power Amplifier Figure 28. 10 Hz Bandpass Filter fO = 10 Hz Q = 2.1 Gain = −8.8 Figure 29. 10 Hz High-Pass Filter fc = 10 Hz d = 0.895 Gain = 1 2 dB passband ripple Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 13 LMC660 SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 www.ti.com TYPICAL SINGLE-SUPPLY APPLICATIONS (continued) + (V = 5.0 VDC) Figure 30. 1 Hz Low-Pass Filter (Maximally Flat, Dual Supply Only) fc = 1 Hz d = 1.414 Gain = 1.57 Figure 31. High Gain Amplifier with Offset Voltage Reduction Gain = −46.8 Output offset voltage reduced to the level of the input offset voltage of the bottom amplifier (typically 1 mV). 14 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 LMC660 www.ti.com SNOSBZ3D – APRIL 1998 – REVISED MARCH 2013 REVISION HISTORY Changes from Revision C (March 2013) to Revision D • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 14 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated Product Folder Links: LMC660 15 PACKAGE OPTION ADDENDUM www.ti.com 16-Nov-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) LMC660AIM NRND SOIC D 14 55 Non-RoHS & Green Call TI Level-1-235C-UNLIM -40 to 85 LMC660AIM LMC660AIM/NOPB ACTIVE SOIC D 14 55 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 LMC660AIM LMC660AIMX NRND SOIC D 14 2500 Non-RoHS & Green Call TI Level-1-235C-UNLIM -40 to 85 LMC660AIM LMC660AIMX/NOPB ACTIVE SOIC D 14 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 LMC660AIM Samples LMC660AIN/NOPB ACTIVE PDIP N 14 25 RoHS & Green NIPDAU Level-1-NA-UNLIM -40 to 85 LMC660AIN Samples LMC660CM NRND SOIC D 14 55 Non-RoHS & Green Call TI Level-1-235C-UNLIM 0 to 70 LMC660CM LMC660CM/NOPB ACTIVE SOIC D 14 55 RoHS & Green SN Level-1-260C-UNLIM 0 to 70 LMC660CM Samples LMC660CMX/NOPB ACTIVE SOIC D 14 2500 RoHS & Green SN Level-1-260C-UNLIM 0 to 70 LMC660CM Samples LMC660CN/NOPB ACTIVE PDIP N 14 25 RoHS & Green NIPDAU Level-1-NA-UNLIM 0 to 70 LMC660CN Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
LMC660AIMX/NOPB 价格&库存

很抱歉,暂时无法提供与“LMC660AIMX/NOPB”相匹配的价格&库存,您可以联系我们找货

免费人工找货