0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LMV710IDBVRE4

LMV710IDBVRE4

  • 厂商:

    BURR-BROWN(德州仪器)

  • 封装:

    SOT23-5

  • 描述:

    IC OPAMP GP 5MHZ RRO SOT23-5

  • 数据手册
  • 价格&库存
LMV710IDBVRE4 数据手册
Not Recommended for New Designs LMV710, LMV711, LMV715 SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN www.ti.com SLOS463A – APRIL 2005 – REVISED JULY 2005 FEATURES • • • • • • • • • 2.7-V and 5-V Performance Low Offset Voltage . . . 0.4 mV Typ, 3 mV Max Input Common-Mode Range . . . 200 mV Beyond the Rails Rail-to-Rail Swing Into 600 Ω Gain Bandwidth . . . 5 MHz Typ Slew Rate . . . 5 V/µs Typ Turn-On Time From Shutdown . . . 1 MΩ (unless otherwise noted) PARAMETER VIO Input offset voltage IIB Input bias current CMRR Common-mode rejection ratio kSVR Supply-voltage rejection ratio VICR Common-mode input voltage range TEST CONDITIONS VIC = 0.85 V and 1.85 V TYP MAX 0.4 3 3.2 25°C 0 ≤ VIC ≤ 2.7 V 2.7 V ≤ VCC+ ≤ 5 V, VIC = 0.85 V 2.7 V ≤ VCC+ ≤ 5 V, VIC = 1.85 V CMRR ≥ 50 dB Sinking VO = 5 V VOH RL = 10 kΩ to 1.35 V VOL Output voltage VOH RL = 600 Ω to 1.35 V VOL 4 25°C 50 –40°C to 85°C 45 25°C 70 –40°C to 85°C 68 25°C 70 –40°C to 85°C Output short circuit current (1) VO MIN –40°C to 85°C Sourcing VO = 0 IOS TA 25°C UNIT mV pA 75 dB 110 dB 95 68 25°C –0.2 to 2.9 –0.3 to 3 25°C 15 28 –40°C to 85°C 12 25°C 25 –40°C to 85°C 22 25°C 2.62 –40°C to 85°C 2.6 25°C V mA 40 2.68 0.01 –40°C to 85°C 0.12 0.15 25°C 2.52 –40°C to 85°C 2.5 25°C 2.55 0.05 –40°C to 85°C V 0.23 0.3 VO(SD) Output voltage level in shutdown mode LMV711 only 25°C 50 IO(SD) Output leakage current in shutdown mode LMV715 only 25°C 1 pA CO(SD) Output capacitance in shutdown mode LMV715 only 25°C 32 pF 25°C 1.22 ICC Supply current ON mode Shutdown mode, SHDN = 0 AV Large-signal voltage gain –40°C to 85°C 25°C 0.002 25°C 80 –40°C to 85°C 76 Sinking RL = 10 kΩ, VO = 0.4 V to 1.35 V 25°C 80 –40°C to 85°C 76 25°C 80 –40°C to 85°C 76 25°C 80 –40°C to 85°C 76 Sinking RL = 600 Ω, VO = 0.5 V to 1.35 V 1.7 1.9 Sourcing RL = 10 kΩ, VO = 1.35 V to 2.3 V Sourcing RL = 600 Ω, VO = 1.35 V to 2.2 V 200 10 mV mA µA 115 113 110 dB 100 SR (2) Slew rate 25°C 5 V/µs GBWP Gain bandwidth product 25°C 5 MHz Φm Phase margin 25°C 60 deg T(on) Amplifier turn-on time 25°C 1 MΩ (unless otherwise noted) PARAMETER TEST CONDITIONS TA V(ON) SHDN Shutdown pin voltage range 25°C MIN TYP 2.4 to 2.7 1.5 to 2.7 V(OFF) Vn Input referred voltage noise 0 to 1 f = 1 kHz 25°C MAX 0 to 0.8 20 UNIT V nV/√Hz Electrical Characteristics VCC+ = 3.2 V, VCC– = GND, and VIC = 1.6 V (unless otherwise noted) PARAMETER TEST CONDITIONS VOH VO Output voltage IO = 6.5 mA VOL TA MIN TYP 25°C 2.95 3 –40°C to 85°C 2.92 25°C –40°C to 85°C 0.01 MAX 0.18 UNIT V 0.25 5 Not Recommended for New Designs LMV710, LMV711, LMV715 SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN www.ti.com SLOS463A – APRIL 2005 – REVISED JULY 2005 Electrical Characteristics VCC+ = 5 V, VCC– = GND, VIC = 2.5 V, and RL > 1 MΩ (unless otherwise noted) PARAMETER VIO Input offset voltage IIB Input bias current CMRR Common-mode rejection ratio kSVR Supply-voltage rejection ratio VICR Common-mode input voltage range TEST CONDITIONS VIC = 0.85 V and 1.85 V TYP MAX 0.4 3 3.2 25°C 0 ≤ VIC ≤ 2.7 V 2.7 V ≤ VCC+ ≤ 5 V, VIC = 0.85 V 2.7 V ≤ VCC+ ≤ 5 V, VIC = 1.85 V CMRR ≥ 50 dB Sinking VO = 5 V VOH RL = 10 kΩ to 1.35 V VOL Output voltage VOH RL = 600 Ω to 1.35 V VOL 4 25°C 50 –40°C to 85°C 48 25°C 70 –40°C to 85°C 68 25°C 70 –40°C to 85°C Output short circuit current (1) VO MIN –40°C to 85°C Sourcing VO = 0 IOS TA 25°C UNIT mV pA 75 dB 110 dB 95 68 25°C –0.2 to 5.2 –0.3 to 5.3 25°C 25 35 –40°C to 85°C 21 25°C 25 –40°C to 85°C 21 25°C 4.92 –40°C to 85°C 4.9 25°C V mA 40 4.98 0.01 –40°C to 85°C 0.12 0.15 25°C 4.82 –40°C to 85°C 4.8 25°C 4.85 0.05 –40°C to 85°C V 0.23 0.3 VO(SD) Output voltage level in shutdown mode LMV711 only 25°C 50 IO(SD) Output leakage current in shutdown mode LMV715 only 25°C 1 pA CO(SD) Output capacitance in shutdown mode LMV715 only 25°C 32 pF 25°C 1.17 ICC Supply current ON mode Shutdown mode, SHDN = 0 AV Large-signal voltage gain –40°C to 85°C 25°C 0.2 25°C 80 –40°C to 85°C 76 Sinking RL = 10 kΩ, VO = 0.4 V to 1.35 V 25°C 80 –40°C to 85°C 76 25°C 80 –40°C to 85°C 76 25°C 80 –40°C to 85°C 76 Sinking RL = 600 Ω, VO = 0.5 V to 1.35 V 1.7 1.9 Sourcing RL = 10 kΩ, VO = 1.35 V to 2.3 V Sourcing RL = 600 Ω, VO = 1.35 V to 2.2 V 200 10 mV mA µA 123 120 110 dB 118 SR (2) Slew rate 25°C 5 V/µs GBWP Gain bandwidth product 25°C 5 MHz Φm Phase margin 25°C 60 deg T(on) Amplifier turn-on time 25°C 1 MΩ (unless otherwise noted) PARAMETER TEST CONDITIONS TA V(ON) SHDN Shutdown pin voltage range 25°C V(OFF) Vn Input referred voltage noise f = 1 kHz MIN TYP 2.4 to 5 2 to 5 0 to 1.5 25°C 20 MAX 0 to 0.8 UNIT V nV/√Hz 7 Not Recommended for New Designs LMV710, LMV711, LMV715 SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN SLOS463A – APRIL 2005 – REVISED JULY 2005 TYPICAL PERFORMANCE CHARACTERISTICS GRAPH PREVIEWS Figure 1. Supply Current vs Supply Voltage (ON Mode) Figure 2. LMV711/LMV715 Supply Current vs Supply Voltage (Shutdown Mode) Figure 3. Output Positive Swing vs Supply Voltage RL = 600 Ω) Figure 4. Output Negative Swing vs Supply Voltage RL = 600 Ω) Figure 5. Output Positive Swing vs Supply Voltage RL = 10 kΩ) Figure 6. Output Negative Swing vs Supply Voltage RL = 10 kΩ) Figure 7. Output Positive Swing vs Supply Voltage (ISRC = 7 mA) Figure 8. Output Negative Swing vs Supply Voltage (ISINK = 7 mA) Figure 9. Input Voltage Noise vs Frequency Figure 10. PSRR vs Frequency Figure 11. CMRR vs Frequency Figure 12. LMV711/LMV715 Turn-On Characteristics Figure 13. Sourcing Current vs Output Voltage Figure 14. Sinking Current vs Output Voltage Figure 15. THD+N vs Frequency (VCC = 5 V) Figure 16. THD+N vs Frequency (VCC = 2.7 V) Figure 17. THD+N vs VOUT (VCC± = ±2.5 V) Figure 18. THD+N vs VOUT (VCC± = ±1.35 V) Figure 19. CCM vs VCM (VCC = 2.7 V) Figure 20. CCM vs VCM (VCC = 5 V) Figure 21. CDIFF vs VCM (VCC = 2.7 V) Figure 22. CDIFF vs VCM (VCC = 5 V) Figure 23. Open-Loop Frequency Response (VCC± = ±1.35 V) Figure 24. Open-Loop Frequency Response (VCC± = ±1.6 V) Figure 25. Open-Loop Frequency Response (VCC± = ±2.5 V) Figure 26. Open-Loop Frequency Response (VCC± = ±1.35 V) Figure 27. Open-Loop Frequency Response (VCC± = ±1.6 V) Figure 28. Open-Loop Frequency Response (VCC± = ±2.5 V) Figure 29. Noninverting Large Signal Pulse Response Figure 30. Noninverting Small Signal Pulse Response Figure Figure 31. Inverting Large Signal Pulse Response Figure 32. Inverting Small Signal Pulse Response Figure 33. VOS vs VCM (VCC = 2.7 V) Figure 34. VOS vs VCM (VCC = 5 V) 8 www.ti.com PACKAGE OPTION ADDENDUM www.ti.com 12-May-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LMV710IDBVR OBSOLETE SOT-23 DBV 5 TBD Call TI Call TI -40 to 85 LMV710IDBVRE4 OBSOLETE SOT-23 DBV 5 TBD Call TI Call TI -40 to 85 LMV710IDBVRG4 OBSOLETE SOT-23 DBV 5 TBD Call TI Call TI -40 to 85 LMV710IDCKR OBSOLETE SC70 DCK 5 TBD Call TI Call TI -40 to 85 LMV710IDCKRE4 OBSOLETE SC70 DCK 5 TBD Call TI Call TI -40 to 85 LMV710IDCKRG4 OBSOLETE SC70 DCK 5 TBD Call TI Call TI -40 to 85 LMV711IDBVR OBSOLETE SOT-23 DBV 6 TBD Call TI Call TI -40 to 85 LMV711IDBVRE4 OBSOLETE SOT-23 DBV 6 TBD Call TI Call TI -40 to 85 LMV711IDBVRG4 OBSOLETE SOT-23 DBV 6 TBD Call TI Call TI -40 to 85 LMV711IDCKR OBSOLETE SC70 DCK 6 TBD Call TI Call TI -40 to 85 LMV711IDCKRE4 OBSOLETE SC70 DCK 6 TBD Call TI Call TI -40 to 85 LMV711IDCKRG4 OBSOLETE SC70 DCK 6 TBD Call TI Call TI -40 to 85 LMV715IDBVR OBSOLETE SOT-23 DBV 6 TBD Call TI Call TI -40 to 85 LMV715IDBVRE4 OBSOLETE SOT-23 DBV 6 TBD Call TI Call TI -40 to 85 LMV715IDBVRG4 OBSOLETE SOT-23 DBV 6 TBD Call TI Call TI -40 to 85 LMV715IDCKR OBSOLETE SC70 DCK 6 TBD Call TI Call TI -40 to 85 LMV715IDCKRE4 OBSOLETE SC70 DCK 6 TBD Call TI Call TI -40 to 85 LMV715IDCKRG4 OBSOLETE SC70 DCK 6 TBD Call TI Call TI -40 to 85 RB4B REB RB5B RFB RB9B RLB (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 12-May-2014 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated
LMV710IDBVRE4 价格&库存

很抱歉,暂时无法提供与“LMV710IDBVRE4”相匹配的价格&库存,您可以联系我们找货

免费人工找货