Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
LMV76x and LMV762Q-Q1 Low-Voltage, Precision Comparator With Push-Pull Output
1 Features
2 Applications
•
•
•
•
•
•
•
•
•
1
•
•
•
•
•
•
•
•
•
•
•
•
•
VS = 5 V, TA = 25°C, Typical Values Unless
Specified
Input Offset Voltage 0.2 mV
Input Offset Voltage (Maximum Over Temp) 1 mV
Input Bias Current 0.2 pA
Propagation Delay (OD = 50 mV) 120 ns
Low Supply Current 300 μA
CMRR 100 dB
PSRR 110 dB
Extended Temperature Range −40°C to +125°C
Push-Pull Output
Ideal for 2.7-V and 5-V Single-Supply Applications
Available in Space-Saving Packages:
–
6-Pin SOT-23 (Single With Shutdown)
–
8-Pin SOIC (Single With Shutdown)
–
8-Pin SOIC and VSSOP (Dual Without
Shutdown)
LMV762Q-Q1 is Qualified for Automotive
Applications
AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
Range
– Device HBM ESD Classification Level 1C
– Device CDM ESD Classification Level M2
Portable and Battery-Powered Systems
Scanners
Set-Top Boxes
High-Speed Differential Line Receiver
Window Comparators
Zero-Crossing Detectors
High-Speed Sampling Circuits
Automotive
3 Description
The LMV76x devices are precision comparators
intended for applications requiring low noise and low
input offset voltage. The LMV761 single has a
shutdown pin that can be used to disable the device
and reduce the supply current. The LMV761 is
available in a space-saving 6-pin SOT-23 or 8-Pin
SOIC package. The LMV762 dual is available in 8-pin
SOIC or VSSOP package. The LMV762Q-Q1 is
available VSSOP and SOIC packages.
These devices feature a CMOS input and push-pull
output stage. The push-pull output stage eliminates
the need for an external pullup resistor.
The LMV76x are designed to meet the demands of
small size, low power and high performance required
by portable and battery-operated electronics.
The input offset voltage has a typical value of 200 μV
at room temperature and a 1-mV limit over
temperature.
Device Information(1)
PART NUMBER
PACKAGE
LMV761
LMV762
LMV762Q-Q1
BODY SIZE (NOM)
SOIC (8)
4.90 mm × 3.91 mm
SOT-23 (6)
2.90 mm × 1.60 mm
SOIC (8)
4.90 mm × 3.91 mm
VSSOP (8)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Threshold Detector
VIN
VOS vs VCC
0.2
VCC
125°C
0.18
0.16
+
VOUT
85°C
0.12
0.1
0.08
-40°C
0.06
-
R2
25°C
0.14
C1 =
0.1µF
VOS (mV)
R1
SD
0.04
0.02
0
VREF
2.5
3
3.5
4
4.5
5
VCC (V)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
4
5
5
5
5
5
6
7
7
8
Absolute Maximum Ratings ......................................
ESD Ratings: LMV761, LMV762...............................
ESD Ratings: LMV762Q-Q1 .....................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
2.7-V Electrical Characteristics ................................
5-V Electrical Characteristics ...................................
2-V Switching Characteristics ...................................
5-V Switching Characteristics ...................................
Typical Characteristics ............................................
Detailed Description ............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram ....................................... 11
7.3 Feature Description................................................. 11
7.4 Device Functional Modes........................................ 12
8
Application and Implementation ........................ 13
8.1 Application Information............................................ 13
8.2 Typical Application ................................................. 13
9 Power Supply Recommendations...................... 15
10 Layout................................................................... 15
10.1 Layout Guidelines ................................................. 15
10.2 Layout Example .................................................... 15
11 Device and Documentation Support ................. 16
11.1
11.2
11.3
11.4
11.5
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
16
16
16
16
16
12 Mechanical, Packaging, and Orderable
Information ........................................................... 16
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision H (March 2013) to Revision I
•
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision G (March 2013) to Revision H
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 15
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
5 Pin Configuration and Functions
LMV761 (Single) DBV Package
6-Pin SOT-23
Top View
1
6
V
+IN
-
V
2
+
5
SD
3
-IN
4
OUT
Pin Functions for SOT-23
PIN
NO.
NAME
TYPE
DESCRIPTION
1
+IN
I
Noninverting input
2
V-
P
Negative power terminal
3
-IN
I
Inverting input
4
OUT
O
Output
5
SDB
I
Shutdown (active low)
6
V+
P
Positive power terminal
LMV761 (Single) D Package
8-Pin SOIC
Top View
N/C
-IN
+IN
V
-
1
8
2
7
3
6
4
5
N/C
+
V
OUT
SD
Pin Functions for SOIC (Single)
PIN
NO.
NAME
TYPE
DESCRIPTION
1
N/C
—
2
-IN
I
Inverting Input
3
+IN
I
Noninverting Input
4
V-
P
Negative Power Terminal
5
SDB
I
Shutdown (active low)
6
OUT
O
Output
+
No Connect (not internally connected)
7
V
P
Positive Power Terminal
8
N/C
—
No Connect (not internally connected)
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
3
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
LMV762, LMV762Q-Q1 (Dual) DBV or DGK Package
8-Pin SOIC or VSSOP
Top View
1
8
2
7
3
6
OUT A
-IN A
+IN A
V
-
+
V
OUT B
-IN B
4
5
+IN B
Pin Functions for SOIC and VSSOP (Dual)
PIN
TYPE
DESCRIPTION
NO.
NAME
1
OUTA
O
Channel A Output
2
-INA
I
Channel A Inverting Input
3
+INA
I
Channel A Noninverting Input
4
V-
P
Negative Power Terminal
5
+INB
I
Channel B Noninverting Input
6
-INB
I
Channel B Inverting Input
7
OUTB
O
Channel B Output
8
V+
P
Positive Power Terminal
6 Specifications
6.1 Absolute Maximum Ratings
See
(1) (2)
MIN
MAX
UNIT
5.5
V
±5
mA
Infrared or convection (20 sec.)
235
°C
Wave soldering (10 sec.) (Lead temp)
260
°C
150
°C
150
°C
Supply voltage (V+ – V−)
Differential input voltage
Supply Voltage
Voltage between any two pins
Output short circuit
duration (3)
Soldering information
Supply Voltage
Current at input pin
Junction temperature
Storage temperature, Tstg
(1)
(2)
(3)
4
−65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output current in excess of ±25 mA over long term may adversely
affect reliability.
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
6.2 ESD Ratings: LMV761, LMV762
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge (1)
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (2)
± 2000
Machine model
± 200
UNIT
V
Unless otherwise specified human body model is 1.5 kΩ in series with 100 pF. Machine model 200 pF.
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 ESD Ratings: LMV762Q-Q1
VALUE
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per AEC Q100-002 (1)
± 2000
Machine model
± 200
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.4 Recommended Operating Conditions
MIN
MAX
Supply voltage (V – V )
2.7
5.25
V
Temperature range
−40
125
°C
+
−
UNIT
6.5 Thermal Information
THERMAL METRIC (1)
RθJA
(1)
(2)
Junction-to-ambient thermal resistance
LMV761
LMV762, LMV762Q-Q1
D (SOIC)
DBV (SOT-23) DGK (VSSOP)
(2)
8 PINS
6 PINS
8 PINS
190
265
235
UNIT
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) – TA) RθJA. All numbers apply for packages soldered directly into a PCB.
6.6
2.7-V Electrical Characteristics
Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V+ / 2, V+ = 2.7 V, V− = 0 V−.
PARAMETER
MIN (1)
TEST CONDITIONS
VOS
Input offset voltage
IB
Input bias current (4)
TYP (2)
MAX (1)
0.2
apply at the temperature extremes (3)
1
(4)
UNIT
mV
0.2
50
pA
0.001
5
pA
IOS
Input offset current
CMRR
Common-mode rejection
ratio
0 V < VCM < VCC – 1.3 V
80
100
dB
PSRR
Power supply rejection ratio
V+ = 2.7 V to 5 V
80
110
dB
CMVR
Input common-mode voltage
range
CMRR > 50 dB
VO
ISC
(1)
(2)
(3)
(4)
(5)
apply at the temperature
extremes (3)
Output swing high
IL = 2 mA, VID = 200 mV
Output swing low
IL = −2 mA, VID = –200 mV
Output short circuit current (5)
−0.3
+
1.5
+
V – 0.35 V – 0.1
90
Sourcing, VO = 1.35 V, VID = 200 mV
6
20
Sinking, VO = 1.35 V, VID = –200 mV
6
15
V
V
250
mV
mA
All limits are specified by testing or statistical analysis.
Typical values represent the most likely parametric norm.
Maximum temperature ensured range is −40°C to +125°C.
Specified by design.
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. See Recommended Operating Conditions for information on temperature
de-rating of this device. Absolute Maximum Rating indicate junction temperature limits beyond which the device may be permanently
degraded, either mechanically or electrically.
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
5
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
2.7-V Electrical Characteristics (continued)
Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V+ / 2, V+ = 2.7 V, V− = 0 V−.
PARAMETER
MIN (1)
TEST CONDITIONS
Supply current LMV761
(single comparator)
IS
TYP (2)
MAX (1)
275
700
LMV762, LMV762Q-Q1 (both
comparators)
apply at the temperature extremes (3)
550
IOUT LEAKAGE
Output leakage I at shutdown SD = GND, VO = 2.7 V
0.2
IS
Supply leakage I at
shutdown
0.2
2
TYP (2)
MAX (1)
LEAKAGE
6.7
1400
SD = GND, VCC = 2.7 V
UNIT
μA
μA
μA
μA
5-V Electrical Characteristics
Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V+ / 2, V+ = 5 V, V− = 0 V−.
PARAMETER
VOS
Input offset voltage
IB
Input bias current (4)
IOS
Input offset current (4)
CMRR
Common-mode rejection
ratio
0.2
apply at the temperature extremes (3)
+
Power supply rejection ratio
CMVR
Input common-mode voltage
range
CMRR > 50 dB
Output swing high
IL = 4 mA, VID = 200 mV
Output swing low
IL = –4 mA, VID = –200 mV
Output short circuit current (5)
ISC
1
0 V < VCM < VCC – 1.3 V
PSRR
VO
MIN (1)
TEST CONDITIONS
V = 2.7 V to 5 V
apply at the temperature
extremes (3)
IS
0.2
50
pA
0.01
5
pA
100
dB
80
110
dB
−0.3
120
Sourcing, VO = 2.5 V, VID = 200 mV
6
60
Sinking, VO = 2.5 V, VID = −200 mV
6
40
225
IOUT LEAKAGE
Output leakage I at
shutdown
SD = GND, VO = 5 V
0.2
IS
Supply leakage I at
shutdown
SD = GND, VCC = 5 V
0.2
6
V
250
mV
V
mA
700
450
apply at the temperature extremes (3)
(1)
(2)
(3)
(4)
(5)
3.8
V+ – 0.1
LMV762, LMV762Q-Q1
(both comparators)
LEAKAGE
mV
80
V+ – 0.35
Supply current LMV761
(single comparator)
UNIT
1400
μA
μA
μA
2
μA
All limits are specified by testing or statistical analysis.
Typical values represent the most likely parametric norm.
Maximum temperature ensured range is −40°C to +125°C.
Specified by design.
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. See Recommended Operating Conditions for information on temperature
de-rating of this device. Absolute Maximum Rating indicate junction temperature limits beyond which the device may be permanently
degraded, either mechanically or electrically.
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
6.8 2-V Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
tPD
TEST CONDITIONS
Propagation delay
RL = 5.1 kΩ
CL = 50 pF
tSKEW
Propagation delay skew
tr
Output rise time
tf
Output fall time
ton
Turnon time from shutdown
MIN
TYP
Overdrive = 5 mV
270
Overdrive = 10 mV
205
Overdrive = 50 mV
120
MAX
UNIT
ns
5
ns
10% to 90%
1.7
ns
90% to 10%
1.8
ns
6
μs
6.9 5-V Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
tPD
TEST CONDITIONS
Propagation delay
RL = 5.1 kΩ
CL = 50 pF
MIN
TYP
Overdrive = 5 mV
225
Overdrive = 10 mV
190
Overdrive = 50 mV
120
MAX
UNIT
ns
tSKEW
Propagation delay skew
5
ns
tr
Output rise time
10% to 90%
1.7
ns
tf
Output fall time
90% to 10%
1.5
ns
ton
Turnon time from shutdown
4
μs
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
7
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
6.10 Typical Characteristics
0.5
125°C
0.45
0.4
SUPPLY CURRENT PER CH (mA)
SUPPLY CURRENT PER CH (mA)
0.5
85°C
0.35
0.3
0.25
25°C
0.2
0.15
-40°C
0.1
0.05
0
1.5
2
2.5
3
3.5
4.5
4
5
5.5
125°C
0.45
0.4
85°C
0.35
0.3
0.25
25°C
0.2
0.15
-40°C
0.1
0.05
0
1.5
6
2
2.5
Figure 1. PSI vs VCC
5
5.5
6
Figure 2. PSI vs VCC
100
125°C
0.18
VS = +2.7 V
80
INPUT BIAS CURRENT (fA)
0.16
25°C
0.14
VOS (mV)
4.5
VO = Low
0.2
85°C
0.12
0.1
0.08
-40°C
0.06
0.04
0.02
60
40
20
0
-20
-40
-60
-80
0
-100
2.5
3
3.5
4.5
4
5
0
0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7
COMMON MODE VOLTAGE (V)
VCC (V)
Figure 4. Input Bias vs Common Mode at 25°C
Figure 3. VOS vs VCC
0.4
100
IL = 4 mA
0.35
+
OUTPUT VOLTAGE, REF TO V (V)
VS = +5 V
80
INPUT BIAS CURRENT (fA)
4
VCC (V)
VO = High
60
40
20
0
-20
-40
-60
-80
0.3
125°C
0.25
85°C
0.2
25°C
0.15
0.1
-40°C
0.5
0
-100
0
4
3
1
2
COMMON MODE VOLTAGE (V)
5
Figure 5. Input Bias vs Common Mode at 25°C
8
3.5
3
VCC (V)
Submit Documentation Feedback
2
2.5
3
3.5
4
4.5
5
5.5
6
VCC (V)
Figure 6. Output Voltage vs Supply Voltage
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
Typical Characteristics (continued)
0.4
OUTPUT VOLTAGE REF TO V (V)
IL = 2 mA
0.14
+
125°C
IL = -4 mA
0.35
125°C
-
OUTPUT VOLTAGE, REF TO V (V)
0.16
0.12
85°C
0.1
25°C
0.08
0.06
0.04
-40°C
0.02
0
0.3
85°C
0.25
25°C
0.2
0.15
0.1
-40°C
0.05
0
2
2.5
3
3.5
4
4.5
5.5
5
6
2
2.5
3
3.5
5.5
6
Figure 8. Output Voltage vs Supply Voltage
0.2
80
IL = -2 mA
0.18
VCC = 5 V
-40°C
70
125°C
25°C
0.16
60
0.14
85°C
ISINK (mA)
85°C
0.12
25°C
0.1
0.08
50
40
125°C
30
0.06
20
0.04
-40°C
10
0.02
0
0
2
2.5
3
3.5
4
4.5
5
5.5
0
6
0.5
1
VCC (V)
Figure 9. Output Voltage vs Supply Voltage
2
1.5
VOUT (V)
2.5
Figure 10. ISOURCE vs VOUT
60
25
-40°C
50
25°C
20
ISOURCE (mA)
85°C
30
125°C
20
VCC = 2.7 V
-40°C
VCC = 5 V
40
ISINK (mA)
5
4.5
4
VCC (V)
Figure 7. Output Voltage vs Supply Voltage
-
OUTPUT VOLTAGE, TO REF V (V)
VCC (V)
25°C
85°C
15
125°C
10
5
10
0
0
0
0.5
1
1.5
2
2.5
0
0.2
0.4
0.6
0.8
1
1.2
1.4
VOUT (V)
VOUT (V)
Figure 11. ISINK vs VOUT
Figure 12. ISOURCE vs VOUT
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
9
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
20
500
-40°C
18
16
PROP DELAY (ns)
12
10
85°C
8
CL = 50 pF
400
25°C
14
ISINK (mA)
RL = 5.1 k:
450
125°C
6
350
300
2.7 V
250
200
5V
150
4
100
VCC = 2.7 V
2
50
0
0
0
0.4
0.2
0.6
1
0.8
1.2
1
1.4
10
Figure 14. Prop Delay vs Overdrive
VCC = 2.7 V
TEMP = 25°C
2 LOAD = 5.1 k:
50 pF
10 mV 5 mV
OVERDRIVE =
50 mV
0
|
|
OVERDRIVE
0
OUTPUT VOLTAGE
(V)
3
INPUT VOLTAGE
(mV)
INPUT VOLTAGE
(mV)
OUTPUT VOLTAGE
(V)
Figure 13. ISINK vs VOUT
1
6
VCC = 5 V
TEMP = 25°C
LOAD = 5.1 k:
50 pF
5
4
3
100
50
150
200
250
OVERDRIVE =
50 mV
1
0
|
|
OVERDRIVE
0
300
50
0
5 mV
OVERDRIVE =
0 50 mV
|
|
150
0
OVERDRIVE
0
50
100
150
200
TIME (ns)
250
300
Figure 17. Response Time vs Input Overdrives Negative
Transition
Submit Documentation Feedback
INPUT VOLTAGE
(mV)
10 mV
200
250
Figure 16. Response Time vs Input Overdrives Positive
Transition
OUTPUT VOLTAGE
(V)
3
VCC = 2.7 V
2 TEMP = 25°C
LOAD = 5.1 k:
50 pF
1
150
100
TIME (ns)
Figure 15. Response Time vs Input Overdrives Positive
Transition
OUTPUT VOLTAGE
(V)
5 mV
2
TIME (ns)
INPUT VOLTAGE
(mV)
10 mV
-150
-150
0
10
100
OVERDRIVE (mV)
VOUT (V)
6
5
4
3
2
1
0
10 mV
VCC = 5 V
TEMP = 25°C
LOAD = 5.1 k:
50 pF
5 mV
OVERDRIVE =
50 mV
|
|
150
0
OVERDRIVE
0
50
100
150
200
250
TIME (ns)
Figure 18. Response Time vs Input Overdrives Negative
Transition
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
7 Detailed Description
7.1 Overview
The LMV76x family of precision comparators is available in a variety of packages and is ideal for portable and
battery-operated electronics.
To minimize external components, the LMV76x family features a push-pull output stage where the output levels
are power-supply determined. In addition, the LMV761 (single) features an active-low shutdown pin that can be
used to disable the device and reduce the supply current.
7.2 Functional Block Diagram
V
VREF
-
VIN
+
+
VO
V
-
7.3 Feature Description
7.3.1 Basic Comparator
A basic comparator circuit is used to convert analog input signals to digital output signals. The comparator
compares an input voltage (VIN) at the noninverting input to the reference voltage (VREF) at the inverting pin. If
VIN is less than VREF the output (VO) is low (VOL). However, if VIN is greater than VREF, the output voltage (VO) is
high (VOH).
V
VREF
-
VIN
+
+
VO
V
-
Figure 19. Basic Comparator Without Hysteresis
Figure 20. Basic Comparator
7.3.2 Hysteresis
The basic comparator configuration may oscillate or produce a noisy output if the applied differential input is near
the input offset voltage of the comparator, which tends to occur when the voltage on one input is equal or very
close to the other input voltage. Adding hysteresis can prevent this problem. Hysteresis creates two switching
thresholds (one for the rising input voltage and the other for the falling input voltage). Hysteresis is the voltage
difference between the two switching thresholds. When both inputs are nearly equal, hysteresis causes one input
to effectively move quickly past the other. Thus, moving the input out of the region in which oscillation may occur.
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
11
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
Feature Description (continued)
Hysteresis can easily be added to a comparator in a noninverting configuration with two resistors and positive
feedback Figure 22. The output will switch from low to high when VIN rises up to VIN1, where VIN1 is calculated by
Equation 1:
VIN1 = [VREF(R1 + R2)] / R2
(1)
The output will switch from high to low when VIN falls to VIN2, where VIN2 is calculated by Equation 2:
VIN2 = [VREF(R1 + R2) – (VCC R1)] / R2
(2)
The Hysteresis is the difference between VIN1 and VIN2, as calculated by Equation 3:
ΔVIN = VIN1 – VIN2 = [VREF(R1 + R2) / R2] – [VREF(R1 + R2)] – [(VCC R1) / R2] = VCC R1 / R2
(3)
VCC
VREF
VO
VIN
+
R1
R2
Figure 21. Basic Comparator With Hysteresis
VO
VIN2
0
VIN1
VIN
Figure 22. Noninverting Comparator Configuration
7.3.3 Input
The LMV76x devices have near-zero input bias current, which allows very high resistance circuits to be used
without any concern for matching input resistances. This near-zero input bias also allows the use of very small
capacitors in R-C type timing circuits. This reduces the cost of the capacitors and amount of board space used.
7.4 Device Functional Modes
7.4.1 Shutdown Mode
The LMV761 features a low-power shutdown pin that is activated by driving SD low. In shutdown mode, the
output is in a high-impedance state, supply current is reduced to 20 nA and the comparator is disabled. Driving
SD high will turn the comparator on. The SD pin must not be left unconnected due to the fact that it is a highimpedance input. When left unconnected, the output will be at an unknown voltage. Do not three-state the SD
pin.
The maximum input voltage for SD is 5.5 V referred to ground and is not limited by VCC. This allows the use of
5-V logic to drive SD while VCC operates at a lower voltage, such as 3 V. The logic threshold limits for SD are
proportional to VCC.
12
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LMV76x are single-supply comparators with 120 ns of propagation delay and 300 µA of supply current.
8.2 Typical Application
A typical application for a LMV76x comparator is a programmable square-wave oscillator.
R4
C1
VC
VO
+
R1
+
VA
R3
V
+
R2
V
0
Figure 23. Square-Wave Oscillator
8.2.1 Design Requirements
The circuit in Figure 23 generates a square wave whose period is set by the RC time constant of the capacitor
C1 and resistor R4. V+ = 5 V unless otherwise specified.
8.2.2 Detailed Design Procedure
The maximum frequency is limited by the large signal propagation delay of the comparator and by the capacitive
loading at the output, which limits the output slew rate.
Figure 24. Square-Wave Oscillator Timing Thresholds
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
13
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
Typical Application (continued)
Consider the output of Figure 23 is high to analyze the circuit. That implies that the inverted input (VC) is lower
than the noninverting input (VA). This causes the C1 to be charged through R4, and the voltage VC increases until
it is equal to the noninverting input. The value of VA at this point is calculated by Equation 4:
VCC ˜ R2
VA1
R2 R1 R R3
(4)
If R1 = R2 = R3, then VA1 = 2 VCC / 3
At this point the comparator switches pulling down the output to the negative rail. The value of VA at this point is
calculated by Equation 5:
VCC (R2 R R3 )
VA2
R1 (R2 R R3 )
(5)
If R1 = R2 = R3, then VA2 = VCC / 3.
The capacitor C1 now discharges through R4, and the voltage VC decreases until it is equal to VA2, at which point
the comparator switches again, bringing it back to the initial stage. The time period is equal to twice the time it
takes to discharge C1 from 2 VCC / 3 to VCC / 3, which is given by R4C1 × ln2. Hence, the formula for the
frequency is calculated by Equation 6:
F = 1 / (2 × R4 × C1 × ln2)
(6)
8.2.3 Application Curve
Figure Figure 25 shows the simulated results of an oscillator using the following values:
•
•
•
•
R1 = R2 = R3 = R4 = 100 kΩ
C1 = 100 pF, CL = 20 pF
V+ = 5 V, V– = GND
CSTRAY (not shown) from Va to GND = 10 pF
6
VOUT
5
Va
VOUT (V)
4
3
2
1
Vc
0
-1
0
10
20
30
40
TIME (µs)
50
C001
Figure 25. Square-Wave Oscillator Output Waveform
14
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
www.ti.com
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
9 Power Supply Recommendations
To minimize supply noise, power supplies must be decoupled by a 0.1-μF ceramic capacitor in parallel with a
10-μF capacitor.
Due to the nanosecond edges on the output transition, peak supply currents will be drawn during output
transitions. Peak current depends on the capacitive loading on the output. The output transition can cause
transients on poorly bypassed power supplies. These transients can cause a poorly bypassed power supply to
ring due to trace inductance and low self-resonance frequency of high ESR bypass capacitors.
Treat the LMV6x as a high-speed device. Keep the ground paths short and place small (low-ESR ceramic)
bypass capacitors directly between the V+ and V– pins.
Output capacitive loading and output toggle rate will cause the average supply current to rise over the quiescent
current.
10 Layout
10.1 Layout Guidelines
The LMV76x is designed to be stable and oscillation free, but it is still important to include the proper bypass
capacitors and ground pick-ups. Ceramic 0.1-μF capacitors must be placed at both supplies to provide clean
switching. Minimize the length of signal traces to reduce stray capacitance.
10.2 Layout Example
C1
GND
R1
+IN
V+
VIN
SOT-23
GND
SD
OUT
-IN
VREF
R2
Figure 26. Comparator With Hysteresis
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
Submit Documentation Feedback
15
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LMV761
Click here
Click here
Click here
Click here
Click here
LMV762
Click here
Click here
Click here
Click here
Click here
LMV762Q-Q1
Click here
Click here
Click here
Click here
Click here
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
16
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
(1)
LMV761MA
ACTIVE
SOIC
D
8
95
Non-RoHS
& Green
Call TI
Level-1-235C-UNLIM
-40 to 125
LMV76
1MA
LMV761MA/NOPB
ACTIVE
SOIC
D
8
95
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LMV76
1MA
LMV761MAX/NOPB
ACTIVE
SOIC
D
8
2500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LMV76
1MA
LMV761MF
ACTIVE
SOT-23
DBV
6
1000
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 125
C22A
LMV761MF/NOPB
ACTIVE
SOT-23
DBV
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
C22A
LMV761MFX
ACTIVE
SOT-23
DBV
6
3000
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 125
C22A
LMV761MFX/NOPB
ACTIVE
SOT-23
DBV
6
3000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
C22A
LMV762MA
ACTIVE
SOIC
D
8
95
Non-RoHS
& Green
Call TI
Level-1-235C-UNLIM
-40 to 125
LMV7
62MA
LMV762MA/NOPB
ACTIVE
SOIC
D
8
95
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LMV7
62MA
LMV762MAX/NOPB
ACTIVE
SOIC
D
8
2500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LMV7
62MA
LMV762MM/NOPB
ACTIVE
VSSOP
DGK
8
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
C23A
LMV762MMX
ACTIVE
VSSOP
DGK
8
3500
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 125
C23A
LMV762MMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
C23A
LMV762QMA/NOPB
ACTIVE
SOIC
D
8
95
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LMV76
2QMA
LMV762QMAX/NOPB
ACTIVE
SOIC
D
8
2500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LMV76
2QMA
LMV762QMM/NOPB
ACTIVE
VSSOP
DGK
8
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
C32A
LMV762QMMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
C32A
The marketing status values are defined as follows:
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
