LP3883ESX-1.2

LP3883 www.ti.com SNVS223F – NOVEMBER 2002 – REVISED APRIL 2013 LP3883 3A Fast-Response Ultra Low Dropout Linear Regulators Check for Samples: LP3883 FEATURES DESCRIPTION • • • • • • • • The LP3883 is a high-current, fast-response regulator which can maintain output voltage regulation with minimum input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages: Vbias provides voltage to drive the gate of the N-MOS power transistor, while Vin is the input voltage which supplies power to the load. The use of an external bias rail allows the part to operate from ultra low Vin voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability. 1 2 Ultra Low Dropout Voltage (210 mV @ 3A typ) Low Ground Pin Current Load Regulation of 0.04%/A 60 nA Typical Quiescent Current in Shutdown 1.5% Output Accuracy (25°C) TO-220, DDPAK/TO-263 Packages Over Temperature/over Current Protection −40°C to +125°C Junction Temperature Range APPLICATIONS • • • • • • • DSP Power Supplies Server Core and I/O Supplies Linear Power Supplies for PC Add-in-Cards Set-Top Box Power Supplies Microprocessor Power Supplies High Efficiency Linear Power Supplies SMPS Post-Regulators The fast transient response of these devices makes them suitable for use in powering DSP, Microcontroller Core voltages and Switch Mode Power Supply post regulators. The parts are available in TO-220 and DDPAK/TO-263 packages. Dropout Voltage: 210 mV (typ) @ 3A load current. Ground Pin Current: 3 mA (typ) at full load. Shutdown Current: 60 nA (typ) when S/D pin is low. Precision Output Voltage: 1.5% room temperature accuracy. Typical Application Circuit At least 4.7 µF of input and output capacitance is required for stability. Connection Diagram Figure 1. TO-220, Top View See NDH0005D Package Figure 2. DDPAK/TO-263, Top View See KTT0005B Package 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2002–2013, Texas Instruments Incorporated LP3883 SNVS223F – NOVEMBER 2002 – REVISED APRIL 2013 www.ti.com Block Diagram These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) −65°C to +150°C Storage Temperature Range Lead Temp. (Soldering, 5 seconds) ESD Rating 260°C Human Body Model (3) Machine Model (4) Power Dissipation (5) 2 kV 200V Internally Limited VIN Supply Voltage (Survival) −0.3V to +6V VBIAS Supply Voltage (Survival) −0.3V to +7V −0.3V to +7V Shutdown Input Voltage (Survival) IOUT (Survival) Internally Limited −0.3V to +6V Output Voltage (Survival) −40°C to +150°C Junction Temperature (1) (2) (3) (4) (5) Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications, see Electrical Characteristics. Specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. The machine model is a 220 pF capacitor discharged directly into each pin. The machine model ESD rating of pin 5 is 100V. At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink thermal values. θJ-A for TO-220 devices is 65°C/W if no heatsink is used. If the TO-220 device is attached to a heatsink, a θJ-S value of 4°C/W can be assumed. θJ-A for DDPAK/TO-263 devices is approximately 40°C/W if soldered down to a copper plane which is at least 1.5 square inches in area. If power dissipation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown. OPERATING RATINGS VIN Supply Voltage (VOUT + VDO) to 5.5V Shutdown Input Voltage 0 to +6V IOUT 3A −40°C to +125°C Operating Junction Temperature Range VBIAS Supply Voltage 2 4.5V to 6V Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated Product Folder Links: LP3883 LP3883 www.ti.com SNVS223F – NOVEMBER 2002 – REVISED APRIL 2013 ELECTRICAL CHARACTERISTICS Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, VBIAS = 4.5V, IL = 10 mA, CIN = COUT = 4.7 µF, VS/D = VBIAS. Symbol VO Parameter Conditions Output Voltage Tolerance 10 mA < IL < 3A VO(NOM) + 1V ≤ VIN ≤ 5.5V 4.5V ≤ VBIAS ≤ 6V Typical (1) MIN (2) MAX (2) 1.198 1.234 1.186 1.246 1.478 1.522 1.455 1.545 1.773 1.827 1.746 1.854 Units 1.216 1.5 V 1.8 (3) ΔVO/ΔVIN Output Voltage Line Regulation VO(NOM) + 1V ≤ VIN ≤ 5.5V 0.01 %/V ΔVO/ΔIL Output Voltage Load Regulation (4) 10 mA < IL < 3A 0.04 0.06 %/A VDO Dropout Voltage (5) IL = 3A 210 270 420 mV IQ(VIN) Quiescent Current Drawn from VIN Supply 10 mA < IL < 3A 3 7 8 mA 0.03 1 30 µA 1 2 3 mA VS/D ≤ 0.3V 0.03 1 30 µA VOUT = 0V 6 VS/D ≤ 0.3V IQ(VBIAS) ISC Quiescent Current Drawn from VBIAS Supply Short-Circuit Current 10 mA < IL < 3A A Shutdown Input VSDT Output Turn-off Threshold Output = ON 0.7 Output = OFF 0.7 Td (OFF) Turn-OFF Delay RLOAD X COUT