0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
ONET8501VRGPR

ONET8501VRGPR

  • 厂商:

    BURR-BROWN(德州仪器)

  • 封装:

    VQFN-20_4X4MM-EP

  • 描述:

    Laser Driver IC 11.3Gbps 1 Channel 2.95 V ~ 3.6 V 20-QFN (4x4)

  • 数据手册
  • 价格&库存
ONET8501VRGPR 数据手册
ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 11.3 Gbps Differential VCSEL Driver With Output Waveform Shaping FEATURES 1 • • • • • • • • • • • Up to 11.3 Gbps Operation 2-Wire Digital Interface Digitally Selectable Modulation Current up to 24 mApp Differential Digitally Selectable Bias Current up to 20 mA Automatic Power Control (APC) Loop Supports Transceiver Management System (TMS) Programmable Input Equalizer Output Waveform Control Includes Laser Safety Features Analog Temperature Sensor Output Selectable Monitor Photodiode Current Range • • • • Output Polarity Select Single 3.3V Supply Operating Temperature –40°C to 85°C Surface Mount Small Footprint 4mm × 4mm 20 Pin RoHS compliant QFN Package APPLICATIONS • • • • • 10 Gigabit Ethernet Optical Transmitters 8x and 10x Fibre Channel Optical Transmitters SONET OC-192/SDH STM-64 Optical Transmitters SFP+ and XFP Transceiver Modules XENPAK, XPAK, X2 and 300-pin MSA Transponder Modules DESCRIPTION The ONET8501V is a high-speed, 3.3V laser driver designed to directly modulate VCSELs at data rates from 2 Gbps up to 11.3 Gbps. The device provides a two-wire serial interface which allows digital control of the modulation and bias currents, eliminating the need for external components. Output waveform control, in the form of cross point control and independent over- and undershoot capability on the rising and falling edges is also available to improve VCSEL edge speeds and the optical eye diagram. An optional input equalizer can be used for equalization of up to 300mm (12 inch) of microstrip or stripline transmission line on FR4 printed circuit boards. The ONET8501V includes an integrated automatic power control (APC) loop as well as circuitry to support laser safety and transceiver management systems. The VCSEL driver is characterized for operation from –40°C to 85°C ambient temperatures and is available in a small footprint 4mm × 4mm 20 pin RoHS compliant QFN package. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. BLOCK DIAGRAM A simplified block diagram of the ONET8501V is shown in Figure 1. The VCSEL driver consists of an equalizer, a limiter, a waveform shaping block with over- and undershoot control, an output driver, power-on reset circuitry, a 2-wire serial interface including a control logic block, a modulation current generator and a bias current generator with automatic power control loop, and an analog reference block. Cp Adjust DC Offset Cancellation VCC Equalizer Over- / Undershoot Generation Delay Buffer + DIN+ Output Driver 50 W 50 W Main Driver MOD+ + 100 W + + DIN- Limiter Boost Shape Control MOD- Peak Driver Adjustable Boost SDA SDA 8 Bit Register 4 Bit SCK DIS SCK 4 Bit DIS 4 Bit 4 Bit 7 Bit + Sign 8 Bit Register 8 Bit Register 8 Bit Register 4 Bit + Sign 4 Bit + Sign Equalizer OS Width US Width OS Height US Height CP Adjust IMOD IBIAS Settings TS Shift TS Slope 2-Wire Interface & Control Logic BIAS MONB Bias Current MONP Generator FLT & APC PD COMP Cp Adjust RZTC Band-Gap & Analog References BGV Power-On Reset Temperature Sensor TS BIAS MONB MONP FLT PD COMP RZTC BGV TS Figure 1. Simplified Block Diagram of the ONET8501V 2 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 PACKAGE The ONET8501V is packaged in a small footprint 4mm × 4mm 20 pin RoHS compliant QFN package with a lead pitch of 0,5 mm. The pin out is shown below. VCC MOD+ MOD- VCC BIAS 20 PIN QFN PACKAGE 4 mm × 4 mm (TOP VIEW) 20 19 18 17 16 15 PD DIS 1 RZTC 2 14 COMP ONET 8501V 20 Pin QFN TS 3 13 MONP 6 7 8 9 10 GND FLT 11 BGV DIN- SDA 5 DIN+ 12 MONB GND SCK 4 TERMINAL FUNCTIONS TERMINAL PIN NO. NAME TYPE DESCRIPTION 1 DIS Digital-in Disables bias, modulation and peaking currents when set to high state. Toggle to reset a fault condition. Recommend shorting pin to GND if disable feature is not used. 2 RZTC Analog Connect external zero TC 28.7kΩ resistor to ground (GND). Used to generate a defined zero TC reference current for internal DACs. 3 TS Analog-out Temperature sensor output. 4 SCK Digital -in 2-wire interface serial clock. Includes a pull-up resistor to VCC. 5 SDA Digital -in 2-wire interface serial data input. Includes a pull-up resistor to VCC. 6, 9, EP GND Supply Circuit ground. Exposed die pad (EP) must be grounded. 7 DIN+ Analog-in Non-inverted data input. On-chip differentially 100Ω terminated to DIN–. Must be AC coupled. 8 DIN– Analog-in Inverted data input. On-chip differentially 100Ω terminated to DIN+. Must be AC coupled. 10 FLT Digital-out Fault detection flag. LVCMOS output with source and sink capability. 11 BGV Anolog-out Buffered bandgap voltage with 1.16V output. This is a replica of the bandgap voltage at RZTC. For best matching, use the same 28.7kΩ resistor to GND as used at RZTC. 12 MONB 13 MONP 14 COMP 15 PD 16 BIAS 17, 20 VCC Analog-out Bias current monitor. Sources a 3.5% replica of the bias current. Connect an external resistor to ground (GND). If the voltage at this pin exceeds 1.16V a fault is triggered. Typically choose a resistor to give MONB voltage of 0.8V at the maximum desired bias current. Photodiode current monitor. Sources a 27% replica of the photodiode current when PDR = 10, a 54% replica when PDR = 01, and a 270% replica when PDR=00. Connect an external resistor (5kΩ typical) to ground (GND). Compensation pin used to control the bandwidth of the APC loop. Connect a 0.01μF capacitor to ground. Analog Photodiode input. Pin can source or sink current dependent on register setting. Sinks average bias current for VCSEL in both APC and open loop modes. Connect to laser cathode through an inductor. BLM15HG102SN1D recommended. Supply 3.3V ± 10% supply voltage Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 3 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 TERMINAL FUNCTIONS (continued) TERMINAL PIN NO. NAME 18 MOD– 19 MOD+ TYPE DESCRIPTION Inverted modulation current output. On-chip 50Ω back-terminated to VCC. IMOD flows into this pin when input data is low. CML-out (current) Non-inverted modulation current output. On-chip 50Ω back-terminated to VCC. IMOD flows into this pin when input data is high. ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE UNIT VCC Supply voltage (2) –0.3 to 4 V VDIS, VRZTC, VTS, VSCK, VSDA, VFLT, VBGV, VMONB, VMONP, VCAPC, VPD, VBIAS VDIN+, VDIN–, VMOD+, VMOD– Voltage at DIS, RZTC, TS, SCK, SDA, FLT, BGV, MONB, MONP, CAPC, PD, BIAS, DIN+, DIN–, MOD+, MOD– (2) –0.3 to 4 V IDIN–, IDIN+ Maximum current at input pins 25 mA IMOD+, IMOD– Maximum current at output pins 30 mA ESD ESD rating at all pins 2 kV (HBM) TJ,max Maximum junction temperature 125 °C TSTG Storage temperature range –65 to 150 °C TA Characterized free-air operating temperature range –40 to 85 °C (1) (2) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability All voltage values are with respect to network ground terminal RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN VCC Supply voltage VIH Digital input high voltage DIS, SCK, SDA VIL Digital input low voltage DIS, SCK, SDA Bias output headroom voltage VBIAS – GND Photodiode current range 2.95 TYP MAX 3.3 3.6 2 UNIT V V 0.8 300 V mV High step size mode, min. step size = 5 μA 25 High step size mode, max. step size = 5 μA 1280 Medium step size mode, min. step size = 2.5 μA 12.5 Medium step size mode, max. step size = 2.5 μA 640 Low step size mode, min. step size = 0.5 μA 2.5 Low step size mode, max. step size = 0.5 μA 128 μA RRZTC Zero TC resistor value (1) vIN Differential input voltage swing tR-IN Input rise time 20%–80% 30 55 ps tF-IN Input fall time 20%–80% 30 55 ps TA Operating free-air temperature 85 °C (1) 4 1.16 V bandgap bias across resistor, E96, 1% accuracy 28.4 28.7 100 –40 29 1200 kΩ mVpp Changing the value will alter the DAC ranges. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 DC ELECTRICAL CHARACTERISTICS Over recommended operating conditions, all values are for open-loop operation, IMODC = 12 mA, IBIASC = 6 mA, and RRZTC = 28.7 kΩ, unless otherwise noted PARAMETER VCC TEST CONDITIONS MIN TYP MAX 2.95 3.3 3.6 IMODC = 12 mA, IBIASC = 6 mA, including IMODC, No waveform shaping, EQENA = 0 50 70 IMODC = 12 mA, IBIASC = 6 mA, including IMODC, No waveform shaping, EQENA = 1 55 75 IMODC = 12 mA, IBIASC = 6 mA, including IMODC, Single sided max output waveform shaping at MOD+ or MOD–, EQENA = 1 75 90 IMODC = 12 mA, IBIASC = 6 mA, including IMODC, Double sided max output waveform shaping at MOD+ or MOD–, EQENA = 1 82 100 Supply voltage IVCC Supply current Disabled (DIS=HIGH) or ENA=LOW, EQENA = 0 UNIT V mA 24 Ω RIN Data input resistance Differential between DIN+ / DIN– 80 100 120 ROUT Data output resistance Single-ended to VCC 40 50 60 Ω Digital input current SCK, SDA, pull up to VCC (1) –10 10 μA Digital input current DIS, pull down to GND (1) –10 10 μA VOH Digital output high voltage FLT, pull-up to VCC, ISOURCE = 1000 μA (2) 2.4 VOL Digital output low voltage FLT, pull-up to VCC, ISINK = 1000 μA (2) IBIAS-DIS Bias current during disable IBIAS-MIN Minimum bias current See IBIAS-MAX Maximum bias current DAC set to maximum, open and closed loop 17 VPD Photodiode reverse bias voltage APC active, IPD = max 1.3 Photodiode fault current level Percent of target IPD (1) (3) ITS μA 20 mA 2.3 V 0.5 (1) With mid scale calibration Temperature sensor drive current Source or sink (1) 2.5 ±4 °C μA 20% 27% IMONP / IPD with control bit PDR = 01 40% 54% 65% IMONP / IPD with control bit PDR = 00 200% 270% 350% 2.9% 3.5% 4.2% 2.4 2.5 2.8 Bias current monitor ratio IMONB / IBIAS (nominal 1/30 = 3.3%) 1.2 kΩ sense resistor. VCC reset threshold voltage VCC voltage level which triggers power-on reset VCC-RSTHYS VCC reset threshold voltage hysteresis VMONB-FLT Fault voltage at MONB 32% 100 Fault occurs if voltage at MONB exceeds value 1.1 V 100 IMONP / IPD with control bit PDR = 10 VCC-RST (1) (2) (3) μA 150% Temperature sensor accuracy Photodiode current monitor ratio V 100 200 Temperature sensor voltage range –40°C to 120°C junction temperature. With Mid scale calibration(1) VTS V 0.4 1.16 V mV 1.2 V Specified by simulation over process, supply and temperature variation External pull up resistor according to timing requirements The bias current can be set below the specified minimum according to the corresponding register setting, however in closed loop operation settings below the specified value may trigger a fault. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 5 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 AC ELECTRICAL CHARACTERISTICS Over recommended operating conditions with 50Ω output load, open loop operation, IMODC = 12 mA, IBIAS = 6 mA, and RRZTC = 28.7 kΩ, unless otherwise noted. Typical operating condition is at VCC = 3.3V and TA = 25°C PARAMETER TEST CONDITIONS MIN 0.01 GHz < f < 3.9 GHz SDD11 SCD11 tR-OUT Differential input return gain Differential to common mode conversion gain Output rise time 3.9 GHz < f < 11.1 GHz (1) 11.1 GHz < f < 20 GHz –3 f < 8.25 GHz –35 8.25 GHz < f < 20 GHz –28 20% – 80%, tR-IN < 40 ps, 100 Ω differential load, no waveform shaping, EQENA = 0, 100 mVpp differential input voltage 20% – 80%, tF-IN < 40 ps, 100 Ω differential load, no waveform shaping, EQENA = 0, 100 mVpp differential input voltage IMOD-MAX Maximum modulation current Output stage tail current IMOD-STEP Modulation current step size full Modulation current step size half DJ Deterministic output jitter Maximum output peaking width Minimum output peaking width Maximum output peaking height Output peaking height step size 16 dB 30 24 30 24 ps mA 100 μA Modulation current smaller than 6 mA 50 EQENA = 0, K28.5 pattern at 11.3 Gbps, no waveform shaping, 100 mVpp, 600 mVpp, 1200 mVpp differential input voltage 3.5 9 8.5 15 psp-p EQENA = 1, K28.5 pattern at 11.3 Gbps, maximum equalization with 12” transmission line at the input, no waveform shaping, 200 mVpp, 600 mVpp, 1200 mVpp differential input voltage 120 Maximum peaking height (2) ps 30 Referred to output stage tail current, high range 10 Referred to output stage tail current, low range 5 Referred to output stage tail current, high range 0.66 Referred to output stage tail current, low range 0.33 Cross point range 600 mVpp differential input Random output jitter 50Ω load, EQENA = 0, 100 mVpp differential input voltage 0.4 τAPC APC time constant CAPC 0.01 μF, IPD = 100 μA, PD coupling ratio CR = 40 (2) 200 tOFF Transmitter disable time Rising edge of DIS to IBIAS ≤ 0.1× IBIAS-NOMINAL (2) tON Disable negate time Falling edge of DIS to IBIAS ≥ 0.9 × IBIAS-NOMINAL tINIT1 Power-on to initialize Power-on to registers ready to be loaded tINIT2 Initialize to transmit Register load STOP command to part ready to transmit valid data (2) tRESET DIS pulse width Time DIS must held high to reset part (2) tFAULT Fault assert time Time from fault condition to FLT high (2) 6 UNIT dB 24 RJ (1) (2) MAX –16 Output fall time tF-OUT TYP mA mA 30–70% 1 (2) 0.2 0.6 psRMS μs 5 μs 1 ms 1 ms 2 ms 50 μs 100 ns Differential Return Gain given by SDD11 = –14 + 13.33 log10(f/5.5), f in GHz Assured by simulation over process, supply and temperature variation Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 DETAILED DESCRIPTION EQUALIZER The data signal can be applied to an input equalizer by means of the input signal pins DIN+/DIN–, which provide on-chip differential 100Ω line-termination. The equalizer is enabled by setting the EQENA = 1 (bit 1 of register 0). Equalization of up to 300mm (12”) of microstrip or stripline transmission line on FR4 printed circuit boards can be achieved. The amount of equalization is digitally controlled by the two-wire interface and control logic block and depends on the register settings EQADJ[0..7] (register 3). The equalizer can also be turned off and bypassed by setting EQENA = 0. For details about the equalizer settings, see Table 16. LIMITER By limiting the output signal of the equalizer to a fixed value, the limiter removes any overshoot after the input equalization and provides the input signal for the output signal waveform shaping. OUTPUT SIGNAL WAVEFORM SHAPING The output signal waveform shaping provides two paths for the data signal. The delay buffer ensures that both paths have the same transit time. The over- and undershoot peaking width and height are controlled through the two wire interface and the peak driver linearly amplifies the signal. The resultant waveform shaped signal is then added to the output of the main driver. The overshoot width is controlled by register 5 settings OSW[0..3] and the overshoot height is controlled by register 6 settings OSH[0..3]. The undershoot width is controlled by register 7 settings USW[0..3] and the undershoot height is controlled by register 8 settings OSH[0..3]. The peaking current is disabled by setting both over- and undershoot height registers to zero. The peaking current is also disabled when the DIS pin is set to a high level or during a fault condition if the fault detection enable register flag FLTEN is set (bit 3 of register 0). HIGH-SPEED OUTPUT DRIVER The modulation current is sunk from the common emitter node of the output driver differential pair by means of a modulation current generator, which is digitally controlled by the 2-wire serial interface. The collector nodes of the output stages are connected to the output pins MOD+/ MOD–, which include on-chip 2 × 50Ω back-termination to VCC. The 50Ω back-termination together with an optional off chip series resistor helps to sufficiently suppress signal distortion caused by double reflections for VCSEL diodes with impedances from 50Ω through 110Ω. The polarity of the output can be selected with the output polarity switch POL (bit 4 of register 9). MODULATION CURRENT GENERATOR The modulation current generator provides the current for the current modulator described above. The circuit is digitally controlled by the 2-wire interface block. An 8-bit wide control bus, MODC[0..7] (register 1), is used to set the desired modulation current. Furthermore, four modulation current ranges can be selected by means of MODRNG1 (bit 1 of register 13) and MODRNG0 (bit 0 of register 13). The modulation current can be disabled by setting the DIS input pin to a high level. The modulation current is also disabled in a fault condition if the fault detection enable register flag FLTEN is set (bit 3 of register 0). DC OFFSET CANCELLATION AND CROSS POINT CONTROL The ONET8501V has DC offset cancellation to compensate for internal offset voltages. The offset cancellation can be disabled by setting OCDIS = 1 (bit 2 of register 9). Disabling the offset cancellation enables the output crossing point to be adjusted from 35% to 65% of the output eye diagram. The crossing point can be moved toward the one level be setting CPSGN = 1 (bit 7 of register 4) and it can be moved toward the zero level by setting CPSGN = 0. The percentage of shift depends upon the register settings CPADJ[0..6] (register 4). Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 7 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 BIAS CURRENT GENERATION AND APC LOOP The bias current generation and APC loop are controlled by means of the 2-wire interface. In open loop operation, selected by setting OLENA = 1 (bit 4 of register 0) the bias current is set directly by the 8-bit wide control word BIASC[0..7] (register 2). In automatic power control mode, selected by setting OLENA = 0, the bias current depends on the register settings BIASC[0..7] and the coupling ratio (CR) between the VCSEL bias current and the photodiode current. CR = IBIAS-VCSEL/ IPD. Three photodiode current ranges can be selected by means of the PDRNG[1..0] bits (register 0). The photodiode range should be chosen to keep the laser bias control DAC, BIASC[0..7], close to the center of its range. This keeps the laser bias current set point resolution high. For details regarding the bias current setting in open- as well as in closed-loop mode, see Table 16. In closed-loop mode, the photodiode polarity bit, PDPOL (bit 0 of register 0), must be set for common-anode or common-cathode configuration to ensure proper operation. ANALOG REFERENCE AND TEMPERATURE SENSOR The ONET8501V VCSEL driver is supplied by a single 3.3V10% supply voltage connected to the VCC pins. This voltage is referred to ground (GND). On-chip bandgap voltage circuitry generates a reference voltage, independent of the supply voltage, from which all other internally required voltages and bias currents are derived. An external zero temperature coefficient resistor must be connected from the RZTC pin of the device to ground (GND). This resistor is used to generate a precise, zero-TC current which is required as a reference current for the on-chip DACs. In order to minimize the module component count, the ONET8501V provides an on-chip temperature sensor. The output voltage of the temperature sensor is available at the TS pin. Due to the die temperature of the 8501V and for high accuracy applications, the use of an external temperature sensor may be required. However, in order to improve the part-to-part accuracy of the sensor, the offset voltage and temperature slope can be adjusted through the 2-wire interface. The offset voltage can be adjusted by means of the TSSH[0..3] bits (register 10) and the direction of the offset can be set by the sign bit TSHSGN (bit 4 of register 10). The temperature slope can be adjusted by means of the TSSL[0..3] bits (register 11) and the sign bit TSLSGN (bit 4 of register 11). The temperature sensor can be disabled by setting TSDIS = 1 (bit 1 of register 9). POWER-ON RESET The ONET8501V has power on reset circuitry which ensures that all registers are reset to zero during startup. After the power-on to initialize time (tINIT1), the internal registers are ready to be loaded. The part is ready to transmit data after the initialize to transmit time (tINIT2), assuming that the chip enable bit ENA is set to 1 and the disable pin DIS is low. The ONET8501V can be disabled using either the ENA control register bit or the disable pin DIS. In both cases the internal registers are not reset. After the disable pin DIS is set low and/or the enable bit ENA is set back to 1, the part returns to its prior output settings. 8 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 2-WIRE INTERFACE AND CONTROL LOGIC The ONET8501V uses a 2-wire serial interface for digital control. The two circuit inputs, SDA and SCK, are driven, respectively, by the serial data and serial clock from a microcontroller, for example. Both inputs include 500kΩ pull-up resistors to VCC. For driving these inputs, an open drain output is recommended. The 2-wire interface allows write access to the internal memory map to modify control registers and read access to read out the control signals. The ONET8501V is a slave device only which means that it cannot initiate a transmission itself; it always relies on the availability of the SCK signal for the duration of the transmission. The master device provides the clock signal as well as the START and STOP commands. The protocol for a data transmission is as follows: 1. START command 2. 7 bit slave address (0001000) followed by an eighth bit which is the data direction bit (R/W). A zero indicates a WRITE and a 1 indicates a READ. 3. 8 bit register address 4. 8 bit register data word 5. STOP command Regarding timing, the ONET8501V is I2C compatible. The typical timing is shown in Figure 2 and a complete data transfer is shown in Figure 3. Parameters for Figure 2 are defined in Table 1. Bus Idle: Both SDA and SCK lines remain HIGH Start Data Transfer: A change in the state of the SDA line, from HIGH to LOW, while the SCK line is HIGH, defines a START condition (S). Each data transfer is initiated with a START condition. Stop Data Transfer: A change in the state of the SDA line from LOW to HIGH while the SCK line is HIGH defines a STOP condition (P). Each data transfer is terminated with a STOP condition; however, if the master still wishes to communicate on the bus, it can generate a repeated START condition and address another slave without first generating a STOP condition. Data Transfer: Only one data byte can be transferred between a START and a STOP condition. The receiver acknowledges the transfer of data. Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge bit. The transmitter releases the SDA line and a device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge clock pulse. Setup and hold times must be taken into account. When a slave-receiver doesn’t acknowledge the slave address, the data line must be left HIGH by the slave. The master can then generate a STOP condition to abort the transfer. If the slave-receiver does acknowledge the slave address but some time later in the transfer cannot receive any more data bytes, the master must abort the transfer. This is indicated by the slave generating the not acknowledge on the first byte to follow. The slave leaves the data line HIGH and the master generates the STOP condition. SDA tBUF tLOW tR tHIGH tHDSTA tF SCK P S S tHDSTA tHDDAT tSUDAT P tSUSTA tSUSTO Figure 2. I2C Timing Diagram Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 9 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 Table 1. Timing Diagram Definitions PARAMETER SYMBOL MIN MAX UNIT 400 kHz SCK clock frequency fSCK Bus free time between START and STOP conditions tBUF 1.3 μs Hold time after repeated START condition. After this period, the first clock pulse is generated tHDSTA 0.6 μs Low period of the SCK clock tLOW 1.3 μs High period of the SCK clock tHIGH 0.6 μs Setup time for a repeated START condition tSUSTA 0.6 μs Data HOLD time tHDDAT 0 μs Data setup time tSUDAT 100 Rise time of both SDA and SCK signals tR 300 ns Fall time of both SDA and SCK signals tF 300 ns Setup time for STOP condition tSUSTO ns μs 0.6 SDA SCK S 1-7 8 9 SLAVE ADDRESS R/W ACK 1-7 8 9 1-7 ACK REGISTER ADDRESS 8 9 ACK REGISTER FUNCTION P Figure 3. Data Transfer REGISTER MAPPING The register mapping for register addresses 0 (0x00) through 13 (0x0D) are shown in Table 2 through Table 15. Table 16 describes the circuit functionality based on the register settings. Table 2. Register 0 (0x00) Mapping – Control Settings Register Address 0 (0x00) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 ENA PDRNG1 PDRNG0 OLENA FLTEN PKRNG EQENA PDPOL Table 3. Register 1 (0x01) Mapping – Modulation Current Register Address 1 (0x01) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 MODC7 MODC6 MODC5 MODC4 MODC3 MODC2 MODC1 MODC0 Table 4. Register 2 (0x02) Mapping – Bias Current Register Address 2 (0x02) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 BIASC7 BIASC6 BIASC5 BIASC4 BIASC3 BIASC2 BIASC1 BIASC0 Table 5. Register 3 (0x03) Mapping – Equalizer Adjust Register Address 3 (0x03) 10 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 EQADJ7 EQADJ6 EQADJ5 EQADJ4 EQADJ3 EQADJ2 EQADJ1 EQADJ0 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 Table 6. Register 4 (0x04) Mapping – Cross Point Adjust Register Address 4 (0x04) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 CPSGN CPADJ6 CPADJ5 CPADJ4 CPADJ3 CPADJ2 CPADJ1 CPADJ0 Table 7. Register 5 (0x05) Mapping – Overshoot Width Register Address 5 (0x05) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — — OSW3 OSW2 OSW1 OSW0 Table 8. Register 6 (0x06) Mapping – Overshoot Height Register Address 6 (0x06) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — — OSH3 OSH2 OSH1 OSH0 Table 9. Register 7 (0x07) Mapping – Undershoot Width Register Address 7 (0x07) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — — USW3 USW2 USW1 USW0 Table 10. Register 8 (0x08) Mapping – Undershoot Height Register Address 8 (0x08) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — — USH3 USH2 USH1 USH0 Table 11. Register 9 (0x09) Mapping – Control Settings Register Address 9 (0x09) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — POL OCSRC OCDIS TSDIS SPDIS Table 12. Register 10 (0x0A) Mapping – Temperature Sensor Shift Register Address 10 (0x0A) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — TSHSGN TSSH3 TSSH2 TSSH1 TSSH0 Table 13. Register 11 (0x0B) Mapping – Temperature Sensor Slope Register Address 11 (0x0B) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — TSLSGN TSSL3 TSSL2 TSSL1 TSSL0 Table 14. Register 12 (0x0C) Mapping – Cross Point Range Register Address 12 (0x0C) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — — — — CPRNG1 CPRNG0 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 11 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 Table 15. Register 13 (0x0D) Mapping – Modulation Range Register Address 13 (0x0D) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 — — — — — — MODRNG1 MODRNG0 Table 16. Register Functionality SYMBOL REGISTER FUNCTION Enable bit 7 Enable chip bit: 1 = chip enabled. Can be toggled low to reset a fault condition 0 = chip disabled PDRNG1 PDRNG0 Photodiode current range bit 6 Photodiode current range bit 5 Photodiode current range bits: With Coupling Ratio CR between VCSEL bias current and photodiode current = 30 1X = 25μA – 1280μA / 5μA resolution 01 = 12.5μA – 640μA / 2.5μA resolution 00 = 2.5μA – 128μA / 0.5μA resolution OLENA Open loop enable bit 4 Open loop enable bit: 1 = open loop bias current control, 0 = closed loop bias current control FLTEN Fault detection enable bit 3 Fault detection enable bit: 1 = fault detection on 0 = fault detection off PKRNG Peaking tail current range bit 2 Laser peaking tail current range (over- and undershoot): 1 = 0mA – 12mA 0 = 0mA – 6mA EQENA Equalizer Enable bit 1 Equalizer enable bit 1 = equalizer enabled 0 = equalizer disabled PDPOL Photodiode polarity bit 0 Photodiode polarity bit: 1 = photodiode cathode connected to VCC 0 = photodiode anode connected to GND MODC7 Modulation current bit 7 (MSB) Modulation current setting: MODC6 Modulation current bit 6 MODC5 Modulation current bit 5 MODRNG = 00 (see below); Modulation current: 24 mA / 94 μA steps MODC4 Modulation current bit 4 MODRNG = 01 (see below): Modulation current: 20 mA / 78 μA steps MODC3 Modulation current bit 3 MODRNG = 10 (see below); Modulation current: 15.8 mA / 62 μA steps MODC2 Modulation current bit 2 MODRNG = 11 (see below); Modulation current: 12 mA / 47 μA steps MODC1 Modulation current bit 1 MODC0 Modulation current bit 0 (LSB) BIASC7 Bias current bit 7 (MSB) Closed loop (APC): BIASC6 Bias current bit 6 Coupling ratio CR = IBIAS-VCSEL / IPD, BIASC = 0 .. 255, IBIAS-VCSEL ≤ 20mA: BIASC5 Bias current bit 5 BIASC4 Bias current bit 4 PDRNG = 00 (see above); IBIAS-VCSEL = 0.5 μA × CR × BIASC BIASC3 Bias current bit 3 PDRNG = 01 (see above); IBIAS-VCSEL = 2.5 μA × CR × BIASC BIASC2 Bias current bit 2 PDRNG = 1X (see above); IBIAS-VCSEL = 5 μA × CR × BIASC BIASC1 Bias current bit 1 BIASC0 Bias current bit 0 (LSB) Open loop: IBIAS-VCSEL = 86 μA × BIASC EQADJ7 Equalizer adjustment bit 7 (MSB) Equalizer adjustment setting EQADJ6 Equalizer adjustment bit 6 EQADJ5 Equalizer adjustment bit 5 EQENA = 0 (see above) EQADJ4 Equalizer adjustment bit 4 Equalizer is turned off and bypassed EQADJ3 Equalizer adjustment bit 3 ENA 12 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 Table 16. Register Functionality (continued) SYMBOL REGISTER FUNCTION EQADJ2 Equalizer adjustment bit 2 EQENA = 1 (see above) EQADJ1 Equalizer adjustment bit 1 Maximum equalization for 00000000 EQADJ0 Equalizer adjustment bit 0 (LSB) Minimum equalization for 11111111 CPSGN Eye crossing sign bit 7 Eye cross-point adjustment setting CPADJ6 Eye crossing adjustment bit 6 (MSB) CPSGN = 1 (positive shift) CPADJ5 Eye crossing adjustment bit 5 CPADJ4 Eye crossing adjustment bit 4 CPADJ3 Eye crossing adjustment bit 3 CPADJ2 Eye crossing adjustment bit 2 Maximum shift for 1111111 CPADJ1 Eye crossing adjustment bit 1 Minimum shift for 0000000 CPADJ0 Eye crossing adjustment bit 0 (LSB) OSW3 Overshoot width adjustment bit 3 (MSB) Overshoot width adjustment setting OSW2 Overshoot width adjustment bit 2 Maximum width for 1111 OSW1 Overshoot width adjustment bit 1 Minimum width for 0000 OSW0 Overshoot width adjustment bit 0 (LSB) OSH3 Overshoot height adjustment bit 3 (MSB) Overshoot height adjustment setting OSH2 Overshoot height adjustment bit 2 Maximum height for 1111 OSH1 Overshoot height adjustment bit 1 Minimum height for 0000 OSH0 Overshoot height adjustment bit 0 (LSB) USW3 Undershoot width adjustment bit 3 (MSB) Undershoot width adjustment setting USW2 Undershoot width adjustment bit 2 Maximum width for 1111 USW1 Undershoot width adjustment bit 1 Minimum width for 0000 USW0 Undershoot width adjustment bit 0 (LSB) USH3 Undershoot height adjustment bit 3 (MSB) Undershoot height adjustment setting USH2 Undershoot height adjustment bit 2 Maximum height for 1111 USH1 Undershoot height adjustment bit 1 Minimum height for 0000 USH0 Undershoot height adjustment bit 0 (LSB) POL Output polarity switch bit 4 Output polarity switch bit 1: pin 18 = MOD+ and pin 19 = MOD0: pin 18 = MOD- and pin 19 = MOD+ OCSRC Offset cancellation source bit 3 Offset cancellation source bit 1: loop connected to the output of the output driver. This requires AC coupling of the output. 0: loop connected to the input of the output driver of the main signal path. OCDIS Offset cancellation disable bit 2 Offset cancellation disable bit 1 = DC offset cancellation is disabled and cross point adjust is enabled 0 = DC offset cancellation is enabled and cross point adjust is disabled TSDIS Temperature sensor disable bit 1 TS disable bit 1 = temperature sensor disabled 0 = temperature sensor enabled SPDIS Signal path disable bit 0 Signal path disable bit 1 = main signal path is disabled, wave shaping path is enabled 0 = main signal path is enabled, wave shaping path is enabled TSHSGN Temperature sensor shift sign bit 4 Temperature sensor shift adjustment setting TSSH3 Temperature sensor shift bit 3 TSHSGN = 1 for a positive shift TSSH2 Temperature sensor shift bit 2 TSHSGN = 0 for a negative shift TSSH1 Temperature sensor shift bit 1 Maximum shift for 1111 TSSH0 Temperature sensor shift bit 0 Minimum shift for 0000 TSLSGN Temperature sensor slope sign bit 4 Temperature sensor slope adjustment setting TSSL3 Temperature sensor shift bit 3 TSLSGN = 1 for a positive shift Maximum shift for 1111111 Minimum shift for 0000000 CPSGN = 0 (negative shift) Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 13 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 Table 16. Register Functionality (continued) SYMBOL REGISTER FUNCTION TSSL2 Temperature sensor shift bit 2 TSLSGN = 0 for a negative shift TSSL1 Temperature sensor shift bit 1 Maximum shift for 1111 TSSL0 Temperature sensor shift bit 0 Minimum shift for 0000 CPRNG1 CPRNG0 Cross point range bit 1 Cross point range bit 0 Cross point adjustment range bits: Minimum adjustment range for 00 Maximum adjustment range for 11 Modulation current reduction bit 1 Modulation current reduction bit 0 Modulation current range reduction bits: 00 = no reduction in modulation current and step size 01 = current range and step size reduced by a factor of 0.833 10 = current range and step size reduced by a factor of 0.66 11 = current range and step size reduced by a factor of 0.5 MODRNG1 MODRNG0 LASER SAFETY FEATURES AND FAULT RECOVERY PROCEDURE The ONET8501V provides built in laser safety features. The following fault conditions are detected: 1. Voltage at MONB exceeds the voltage at RZTC (1.16V), 2. Photodiode current exceeds 150% of its set value, 3. Bias control DAC drops in value by more than 50% in one step If one or more fault conditions occur and the fault enable bit FLTEN is set to 1, the ONET8501V responds by: 1. Setting the VCSEL bias current to zero. 2. Setting the modulation current to zero. 3. Setting the peaking current to zero 4. Asserting and latching the FLT pin. Fault recovery is performed by the following procedure: 1. The disable pin DIS and/or the internal enable control bit ENA are toggled for at least the fault latch reset time tRESET. 2. The FLT pin de-asserts while the disable pin DIS is asserted or the enable bit ENA is de-asserted. 3. If the fault condition is no longer present, the part will return to normal operation with its prior output settings after the disable negate time tON. 4. If the fault condition is still present, FLT re-asserts once DIS is set to a low level and the part will not return to normal operation. 14 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 TYPICAL OPERATION CHARACTERISTICS Typical operating condition is at VCC = 3.3V, TA = 25°C, IBIASC = 6 mA, IMODC = 12 mA, VIN = 600 mVpp and no waveform shaping (unless otherwise noted). DETERMINISTIC JITTER vs TEMPERATURE 8 8 6 6 Deterministic Jitter - pspp Deterministic Jitter - pspp DETERMINISTIC JITTER vs MODULATION CURRENT 4 2 0 0 5 10 15 20 4 2 0 -40 25 -20 Modulation Current - mA Figure 4. 0 20 40 60 80 TA - Free-Air Temperature -°C 100 Figure 5. RANDOM JITTER vs MODULATION CURRENT RANDOM JITTER vs TEMPERATURE 0.6 0.4 Deterministic Jitter - psrms Deterministic Jitter - psrms 0.5 0.4 0.3 0.2 0.3 0.2 0.1 0.1 0 0 5 10 15 20 Modulation Current - mA 25 0 -40 Figure 6. -20 0 20 40 60 80 TA - Free-Air Temperature -°C 100 Figure 7. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 15 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 TYPICAL OPERATION CHARACTERISTICS (continued) Typical operating condition is at VCC = 3.3V, TA = 25°C, IBIASC = 6 mA, IMODC = 12 mA, VIN = 600 mVpp and no waveform shaping (unless otherwise noted). RISE-TIME AND FALL-TIME vs MODULATION CURRENT RISE-TIME AND FALL-TIME vs TEMPERATURE 35 35 30 30 Fall Time Transition Time - ps Transition Time - ps 25 Rise Time 20 15 10 Fall Time 25 Rise Time 20 15 10 5 5 0 0 -40 0 5 10 15 20 Modulation Current - mA Figure 8. 25 -20 0 20 40 60 80 TA - Free-Air Temperature -°C 100 Figure 9. BIAS CURRENT IN OPEN LOOP MODE vs BIASC REGISTER SETTING BIAS-MONITOR CURRENT IMONB vs BIAS CURRENT 0.8 25 Bias Monitor Current - mA Open Loop Bias Current - mA 0.7 20 15 10 0.6 0.5 0.4 0.3 0.2 5 0.1 0 0 50 100 150 200 250 Bias Current Register Setting (Decimal) 300 0 0 Figure 10. 16 Submit Documentation Feedback 5 10 15 Bias Current - mA Figure 11. 20 25 Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 TYPICAL OPERATION CHARACTERISTICS (continued) Typical operating condition is at VCC = 3.3V, TA = 25°C, IBIASC = 6 mA, IMODC = 12 mA, VIN = 600 mVpp and no waveform shaping (unless otherwise noted). MODULATION CURRENT vs MODC REGISTER SETTING 0.5 25 0.4 20 Modulation Current - mA Bias Monitor Current - mA PHOTODIODE-MONITOR CURRENT IMONP vs PD CURRENT, PDR = 00 0.3 0.2 15 10 5 0.1 0 0 0 0.02 0.04 0.06 0.08 0.10 Photodiode Current - mA Figure 12. 0.12 0 0.14 50 100 150 200 250 300 Modulation Current Register Setting (Decimal) Figure 13. SUPPLY CURRENT vs TEMPERATURE TEMPERATURE SENSOR VOLTAGE VTS vs TEMPERATURE 75 2 70 Temp Sensor Voltage - mV Supply Current - mA 65 60 55 50 45 40 1.5 1 0.5 35 30 25 -40 -20 0 20 40 60 80 TA - Free-Air Temperature -°C 100 0 -40 -20 Figure 14. 0 20 40 60 80 TA - Free-Air Temperature -°C 100 Figure 15. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 17 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 TYPICAL OPERATION CHARACTERISTICS (continued) Typical operating condition is at VCC = 3.3V, TA = 25°C, IBIASC = 6 mA, IMODC = 12 mA, VIN = 600 mVpp and no waveform shaping (unless otherwise noted). EYE-DIAGRAM AT 11.3GBPS K28.5 PATTERN, IMOD=6mA, EQENA = 0 190mv/Div 14.8ps/Div EYE-DIAGRAM AT 11.3GBPS K28.5 PATTERN, IMOD=10mA, EQENA = 0 Figure 16. Figure 17. EYE-DIAGRAM AT 11.3GBPS K28.5 PATTERN, IMOD=6mA, EQENA = 0, OSH = USH = 8, OSW = USW = 2, PKRNG = 0 EYE-DIAGRAM AT 8.5GBPS K28.5 PATTERN, IMOD=6mA, EQENA = 0 190mv/Div 14.8ps/Div 190mv/Div Figure 18. 18 14.8ps/Div 400mv/Div 20ps/Div Figure 19. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 TYPICAL OPERATION CHARACTERISTICS (continued) Typical operating condition is at VCC = 3.3V, TA = 25°C, IBIASC = 6 mA, IMODC = 12 mA, VIN = 600 mVpp and no waveform shaping (unless otherwise noted). EYE-DIAGRAM AT 11.3GBPS K28.5 PATTERN, IMOD=6mA, EQENA = 1, 12" OF FR4 AT INPUTS 190mv/Div 14.8ps/Div Figure 20. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 19 ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 APPLICATION INFORMATION Figure 21 shows a typical application circuit using the ONET8501V with a VCSEL diode, anode connected to VCC, and driven differentially. The VCSEL driver is controlled via the 2-wire interface SDA/SCK by a microcontroller. In a typical application, the FLT, MONP, MONP and TS outputs are also connected to the microcontroller for transceiver management purposes. The component values in Figure 21 are typical examples and may be varied according to the intended application. Single-ended VCSEL drive can be done by terminating the unused driver output in a resistance that matches the VCSEL series resistance, however, the available VCSEL modulation current will be halved. DIS TS SDK SDA DIS RZTC SCK SDA C1 0.1µF TS RZTC 28.7kΩ GND FLT BIAS 0.1µF C4 C8 0.1µF PD COMP VCC MONP L2 BLM15HD102SN1 VCSEL MOD- GND BGV FLT Optional 100Ω Diff TL 100Ω Diff TL ONET8501V DINC2 0.1µF C3 0.1µF MOD+ MONB DIN- L1 C9 0.1µF VCC DIN+ DIN+ 100nH LQW15ANR10J00 BLM15HD102SN1 L3 100nH LQW15ANR10J00 L4 VCC BGV RBGV 28.7kΩ Monitor Photodiode Optional C5 0.01µF C6 0.1µF L5 BLM15HG102SN1 VCC MONB RMONB 1.2kΩ MONP RMONP 5kΩ C7 0.01µF Figure 21. Typical Application Circuit With a Differential Driven VCSEL In the recommended application circuit, the purpose of the optional series resistors is to improve the signal integrity between the VCSEL driver and the VCSEL. Since the VCSEL impedance varies depending on its type, the series resistor may provide better matching impedance for the modulation current outputs. LAYOUT GUIDELINES For optimum performance, use 50Ω transmission lines (100Ω differential) for connecting the signal source to the DIN+ and DIN– pins and for connecting the modulation current outputs, MOD+ and MOD–, to the VCSEL. The length of the transmission lines should be kept as short as possible to reduce loss and pattern-dependent jitter. It is recommended to assemble the series matching resistors as close as possible to the TOSA. 20 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V ONET8501V www.ti.com SLLS837B – JUNE 2007 – REVISED SEPTEMBER 2007 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Original (June 2007) to Revision A ......................................................................................................... Page • • • Changed the IVCC MAX supply current (first row) from 85 to 70 mA. ................................................................................... 5 Changed the IVCC MAX supply current (second row) from 70 to 75 mA................................................................................ 5 Changed first sentence in the Data Transfer section from "The number of data bytes transferred between a START and a STOP condition is not limited and is determined by the master device.".................................................................... 9 Changes from Revision A (July 2007) to Revision B ..................................................................................................... Page • Changed TSTG Max from 85°C ............................................................................................................................................... 4 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): ONET8501V 21 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) ONET8501VRGPR ACTIVE QFN RGP 20 3000 RoHS & Green NIPDAU Level-3-260C-168 HR -40 to 85 ONET 8501V Samples ONET8501VRGPT ACTIVE QFN RGP 20 250 RoHS & Green NIPDAU Level-3-260C-168 HR -40 to 85 ONET 8501V Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
ONET8501VRGPR 价格&库存

很抱歉,暂时无法提供与“ONET8501VRGPR”相匹配的价格&库存,您可以联系我们找货

免费人工找货