OPA228PA

OPA227 OPA 4 OPA 227 OPA 2 OPA 42 27 227 227 OPA2227 OPA4227 OPA2 27 OPA2 227 OPA228 OPA2228 OPA4228 SBOS110A – MAY 1998 – REVISED JANUARY 2005 High Precision, Low Noise OPERATIONAL AMPLIFIERS FEATURES q LOW NOISE: 3nV/√Hz q WIDE BANDWIDTH: OPA227: 8MHz, 2.3V/µs OPA228: 33MHz, 10V/µs q SETTLING TIME: 5µs (significant improvement over OP-27) q q q q q q HIGH CMRR: 138dB HIGH OPEN-LOOP GAIN: 160dB LOW INPUT BIAS CURRENT: 10nA max LOW OFFSET VOLTAGE: 75µV max WIDE SUPPLY RANGE: ±2.5V to ±18V OPA227 REPLACES OP-27, LT1007, MAX427 DESCRIPTION The OPA227 and OPA228 series op amps combine low noise and wide bandwidth with high precision to make them the ideal choice for applications requiring both ac and precision dc performance. The OPA227 is unity-gain stable and features high slew rate (2.3V/µs) and wide bandwidth (8MHz). The OPA228 is optimized for closed-loop gains of 5 or greater, and offers higher speed with a slew rate of 10V/µs and a bandwidth of 33MHz. The OPA227 and OPA228 series op amps are ideal for professional audio equipment. In addition, low quiescent current and low cost make them ideal for portable applications requiring high precision. The OPA227 and OPA228 series op amps are pin-for-pin replacements for the industry standard OP-27 and OP-37 with substantial improvements across the board. The dual and quad versions are available for space savings and perchannel cost reduction. The OPA227, OPA228, OPA2227, and OPA2228 are available in DIP-8 and SO-8 packages. The OPA4227 and OPA4228 are available in DIP-14 and SO-14 packages with standard pin configurations. Operation is specified from –40°C to +85°C. OPA4227, OPA4228 Out A –In A 1 2 A D 12 11 10 B –In B 6 7 DIP-14, SO-14 C 9 8 –In C Out C +In D V– +In C 3 4 5 14 13 Out D –In D q OPA228 REPLACES OP-37, LT1037, MAX437 q SINGLE, DUAL, AND QUAD VERSIONS APPLICATIONS q q q q q q q DATA ACQUISITION TELECOM EQUIPMENT GEOPHYSICAL ANALYSIS VIBRATION ANALYSIS SPECTRAL ANALYSIS PROFESSIONAL AUDIO EQUIPMENT ACTIVE FILTERS q POWER SUPPLY CONTROL SPICE model available for OPA227 at www.ti.com OPA2227, OPA2228 OPA227, OPA228 +In A V+ Out A Trim –In +In V– 1 2 3 4 DIP-8, SO-8 NC = Not Connected 8 7 6 5 Trim V+ Output NC 1 2 3 4 DIP-8, SO-8 A B 8 7 6 5 V+ +In B –In A +In A V– Out B –In B Out B +In B Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1998-2005, Texas Instruments Incorporated www.ti.com SPECIFICATIONS: VS = ±5V to ±15V OPA227 Series At TA = +25°C, and RL = 10kΩ, unless otherwise noted. Boldface limits apply over the specified temperature range, TA = –40°C to +85°C. OPA227P, U OPA2227P, U PARAMETER OFFSET VOLTAGE Input Offset Voltage VOS OTA = –40°C to +85°Cver Temperature vs Temperature dVOS/dT vs Power Supply PSRR TA = –40°C to +85°C vs Time Channel Separation (dual, quad) INPUT BIAS CURRENT Input Bias Current TA = –40°C to +85°C Input Offset Current TA = –40°C to +85°C NOISE Input Voltage Noise, f = 0.1Hz to 10Hz Input Voltage Noise Density, f = 10Hz en f = 100Hz f = 1kHz Current Noise Density, f = 1kHz in INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection TA = –40°C to +85°C INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain TA = –40°C to +85°C TA = –40°C to +85°C FREQUENCY RESPONSE Gain Bandwidth Product GBW Slew Rate SR Settling Time: 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise THD+N OUTPUT Voltage Output TA = –40°C to +85°C TA = –40°C to +85°C Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) TA = –40°C to +85°C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SO-8 Surface Mount DIP-8 DIP-14 SO-14 Surface Mount ✻ Specifications same as OPA227P, U. AOL VCM CMRR (V–)+2 120 120 CONDITION MIN TYP ±5 VS = ±2.5V to ±18V MAX ±75 ±2 ±2 OPA227PA, UA OPA2227PA, UA OPA4227PA, UA MIN TYP ±10 MAX ±200 UNITS µV µV µV/°C µV/V µV/V µV/mo µV/V dB nA nA nA nA nVp-p nVrms nV/√Hz nV/√Hz nV/√Hz pA/√Hz ✻ ✻ V dB dB Ω || pF Ω || pF dB dB dB dB MHz V/µs µs µs µs % ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ V V V V mA ±0.1 0.2 0.2 110 ±0.5 ±100 ±0.6 ±0.3 ✻ ✻ ✻ ✻ ±200 ±2 ✻ ✻ dc f = 1kHz, RL = 5kΩ IB IOS ±2.5 ±2.5 ±10 ±10 ±10 ±10 ✻ ✻ ✻ ✻ ✻ ✻ 90 15 3.5 3 3 0.4 (V+)–2 138 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ VCM = (V–)+2V to (V+)–2V VCM = (V–)+2V to (V+)–2V VO = (V–)+2V to (V+)–2V, RL = 10kΩ VO = (V–)+3.5V to (V+)–3.5V, RL = 600Ω 132 132 132 132 107 || 12 109 || 3 160 160 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ G = 1, 10V Step, CL = 100pF G = 1, 10V Step, CL = 100pF VIN • G = VS f = 1kHz, G = 1, VO = 3.5Vrms RL = RL = RL = RL = 10kΩ 10kΩ 600Ω 600Ω (V–)+2 (V–)+2 (V–)+3.5 (V–)+3.5 8 2.3 5 5.6 1.3 0.00005 (V+)–2 (V+)–2 (V+)–3.5 (V+)–3.5 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ISC CLOAD VS IQ IO = 0 IO = 0 ±45 See Typical Curve ±5 ±2.5 ±15 ±18 ±3.8 ±4.2 +85 +125 +150 150 100 80 100 ±3.7 V V mA mA °C °C °C °C/W °C/W °C/W °C/W θJA –40 –55 –65 ✻ ✻ ✻ 2 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A SPECIFICATIONS: VS = ±5V to ±15V OPA228 Series At TA = +25°C, and RL = 10kΩ, unless otherwise noted. Boldface limits apply over the specified temperature range, TA = –40°C to +85°C. OPA228P, U OPA2228P, U PARAMETER OFFSET VOLTAGE Input Offset Voltage VOS OTA = –40°C to +85°Cver Temperature vs Temperature dVOS/dT vs Power Supply PSRR TA = –40°C to +85°C vs Time Channel Separation (dual, quad) INPUT BIAS CURRENT Input Bias Current TA = –40°C to +85°C Input Offset Current TA = –40°C to +85°C NOISE Input Voltage Noise, f = 0.1Hz to 10Hz Input Voltage Noise Density, f = 10Hz en f = 100Hz f = 1kHz Current Noise Density, f = 1kHz in INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection TA = –40°C to +85°C INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain TA = –40°C to +85°C TA = –40°C to +85°C FREQUENCY RESPONSE Minimum Closed-Loop Gain Gain Bandwidth Product GBW Slew Rate SR Settling Time: 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise THD+N OUTPUT Voltage Output TA = –40°C to +85°C TA = –40°C to +85°C Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) TA = –40°C to +85°C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SO-8 Surface Mount DIP-8 DIP-14 SO-14 Surface Mount ✻ Specifications same as OPA228P, U. AOL VCM CMRR (V–)+2 120 120 CONDITION MIN TYP ±5 VS = ±2.5V to ±18V MAX ±75 ±2 ±2 OPA228PA, UA OPA2228PA, UA OPA4228PA, UA MIN TYP ±10 MAX ±200 UNITS µV µV µV/°C µV/V µV/V µV/mo µV/V dB nA nA nA nA nVp-p nVrms nV/√Hz nV/√Hz nV/√Hz pA/√Hz ✻ ✻ V dB dB Ω || pF Ω || pF dB dB dB dB V/V MHz V/µs µs µs µs % ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ V V V V mA ±0.1 0.2 0.2 110 ±0.5 ±100 ±0.6 ±0.3 ✻ ✻ ✻ ✻ ±200 ±2 ✻ ✻ dc f = 1kHz, RL = 5kΩ IB IOS ±2.5 ±2.5 ±10 ±10 ±10 ±10 ✻ ✻ ✻ ✻ ✻ ✻ 90 15 3.5 3 3 0.4 (V+)–2 138 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ VCM = (V–)+2V to (V+)–2V VCM = (V–)+2V to (V+)–2V VO = (V–)+2V to (V+)–2V, RL = 10kΩ VO = (V–)+3.5V to (V+)–3.5V, RL = 600Ω 132 132 132 132 107 || 12 109 || 3 160 160 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ G = 5, 10V Step, CL = 100pF, CF =12pF G = 5, 10V Step, CL = 100pF, CF =12pF VIN • G = VS f = 1kHz, G = 5, VO = 3.5Vrms RL = RL = RL = RL = 10kΩ 10kΩ 600Ω 600Ω (V–)+2 (V–)+2 (V–)+3.5 (V–)+3.5 5 33 11 1.5 2 0.6 0.00005 (V+)–2 (V+)–2 (V+)–3.5 (V+)–3.5 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ISC CLOAD VS IQ IO = 0 IO = 0 ±45 See Typical Curve ±5 ±2.5 ±15 ±18 ±3.8 ±4.2 +85 +125 +150 150 100 80 100 ±3.7 V V mA mA °C °C °C °C/W °C/W °C/W °C/W θJA –40 –55 –65 ✻ ✻ ✻ OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A www.ti.com 3 ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage .................................................................................. ±18V Signal Input Terminals, Voltage ........................ (V–) –0.7V to (V+) +0.7V Current ....................................................... 20mA Output Short-Circuit(2) .............................................................. Continuous Operating Temperature .................................................. –55°C to +125°C Storage Temperature ..................................................... –65°C to +150°C Junction Temperature ...................................................................... 150°C Lead Temperature (soldering, 10s) ................................................. 300°C NOTE: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Short-circuit to ground, one amplifier per package. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum located at the end of this datasheet, or refer to our web site at www.ti.com. 4 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A TYPICAL PERFORMANCE CURVES At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted. OPEN-LOOP GAIN/PHASE vs FREQUENCY 180 160 140 120 AOL (dB) OPEN-LOOP GAIN/PHASE vs FREQUENCY 0 180 160 140 120 Phase (°) AOL (dB) 0 OPA227 G –20 –40 –60 –80 OPA228 –20 –40 G –60 Phase (°) 100 80 60 40 20 0 –20 0.01 0.10 1 10 100 1k φ 100 80 60 40 20 0 –20 0.01 0.10 1 10 100 1k –80 –100 –120 –140 –160 –180 –200 10k 100k 1M 10M 100M φ –100 –120 –140 –160 –180 –200 10k 100k 1M 10M 100M Frequency (Hz) Frequency (Hz) POWER SUPPLY AND COMMON-MODE REJECTION RATIO vs FREQUENCY 140 120 INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY 100k PSRR, CMRR (dB) 100 80 60 40 -20 –0 0.1 1 10 100 1k 10k 100k 1M Frequency (Hz) +PSRR –PSRR Voltage Noise (nV/√Hz) Current Noise (fA/√Hz) +CMRR 10k Current Noise 1k 100 10 Voltage Noise 1 0.1 1 10 100 1k 10k Frequency (Hz) TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 0.01 VOUT = 3.5Vrms 0.01 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY VOUT = 3.5Vrms OPA227 OPA228 THD+Noise (%) 0.001 THD+Noise (%) 0.001 0.0001 G = 1, RL = 10kΩ 0.0001 G = 1, RL = 10kΩ 0.00001 20 100 1k Frequency (Hz) 10k 20k 0.00001 20 100 1k Frequency (Hz) 10k 50k OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A www.ti.com 5 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, RL =10kΩ, and VS = ±15V, unless otherwise noted. INPUT NOISE VOLTAGE vs TIME 140 CHANNEL SEPARATION vs FREQUENCY Channel Separation (dB) 120 50nV/div 100 80 Dual and quad devices. G = 1, all channels. Quad measured Channel A to D, or B to C; other combinations yield similiar or improved rejection. 10 100 1k 10k 100k 1M 60 40 1s/div Frequency (Hz) VOLTAGE NOISE DISTRIBUTION (10Hz) 24 OFFSET VOLTAGE PRODUCTION DISTRIBUTION 17.5 15.0 Percent of Amplifiers (%) Typical distribution of packaged units. Percent of Units (%) 16 12.5 10.0 5.5 5.0 2.5 8 0 0 3.16 3.25 3.34 3.43 3.51 3.60 3.69 3.78 0 –150 –135 –120 –105 –90 –75 –60 –45 –30 –15 0 15 30 45 60 75 90 105 120 135 150 Noise (nV/√Hz) Offset Voltage (µV) OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 12 Typical distribution of packaged units. WARM-UP OFFSET VOLTAGE DRIFT 10 8 Offset Voltage Change (µV) Percent of Amplifiers (%) 6 4 2 0 –2 –4 –6 –8 8 4 0 0 0.5 1.0 1.5 –10 0 50 100 150 200 250 300 Offset Voltage Drift (µV)/°C Time from Power Supply Turn-On (s) 6 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted. AOL, CMRR, PSRR vs TEMPERATURE 160 150 CMRR AOL AOL, CMRR, PSRR vs TEMPERATURE 160 150 AOL, CMRR, PSRR (dB) AOL CMRR AOL, CMRR, PSRR (dB) 140 130 120 110 100 90 80 70 60 –75 PSRR 140 130 120 110 100 90 80 70 PSRR OPA227 OPA228 –50 –25 0 25 50 75 100 125 60 –75 –50 –25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) INPUT BIAS CURRENT vs TEMPERATURE 2.0 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –60 Short-Circuit Current (mA) 60 50 40 SHORT-CIRCUIT CURRENT vs TEMPERATURE Input Bias Current (nA) +ISC 30 20 10 0 –75 –ISC –40 –20 0 20 40 60 80 100 120 140 –50 –25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) QUIESCENT CURRENT vs TEMPERATURE 5.0 ±18V ±15V ±12V ±10V ±5V 3.5 ±2.5V 3.8 QUIESCENT CURRENT vs SUPPLY VOLTAGE Quiescent Current (mA) Quiescent Current (mA) 4.5 3.6 4.0 3.4 3.2 3.0 3.0 2.5 –60 –40 –20 0 20 40 60 80 100 120 140 Temperature (°C) 2.8 0 2 4 6 8 10 12 14 16 18 20 Supply Voltage (±V) OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A www.ti.com 7 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted. SLEW RATE vs TEMPERATURE 3.0 12 SLEW RATE vs TEMPERATURE OPA227 2.5 Slew Rate (µV/V) 2.0 1.5 1.0 0.5 0 –75 –50 –25 0 25 50 75 100 125 Temperature (°C) RLOAD = 2kΩ CLOAD = 100pF Positive Slew Rate Slew Rate (µV/V) Negative Slew Rate 10 8 6 4 2 0 OPA228 RLOAD = 2kΩ CLOAD = 100pF –75 –50 –25 0 25 50 75 100 125 Temperature (°C) CHANGE IN INPUT BIAS CURRENT vs POWER SUPPLY VOLTAGE 2.0 1.5 1.0 Curve shows normalized change in bias current with respect to VS = ±10V. Typical IB may range from –2nA to +2nA at VS = ±10V. ∆IB (nA) 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 0 5 10 15 20 25 30 35 40 –15 CHANGE IN INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE Curve shows normalized change in bias current with respect to VCM = 0V. Typical IB may range from –2nA to +2nA at VCM = 0V. ∆IB (nA) 0.5 0 –0.5 –1.0 –1.5 –2.0 Supply Voltage (V) VS = ±15V VS = ±5V –10 –5 0 5 10 15 Common-Mode Voltage (V) SETTLING TIME vs CLOSED-LOOP GAIN 100 15 VS = ±15V, 10V Step CL = 1500pF RL = 2kΩ 14 Output Voltage Swing (V) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT V+ (V+) –1V 125°C –40°C 85°C 25°C 85°C 25°C –55°C (V+) –2V (V+) –3V 13 12 11 10 –10 –11 –12 –13 –14 –15 125°C Settling Time (µs) OPA227 10 0.01% 0.1% OPA228 0.01% 0.1% –55°C –40°C (V–) +3V (V–) +2V (V–) +1V V– 1 ±1 ±10 Gain (V/V) ±100 0 10 20 30 40 50 60 Output Current (mA) 8 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted. MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 30 VS = ±15V 25 Output Voltage (Vp-p) 70 SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE OPA227 60 50 OPA227 Gain = +10 Overshoot (%) 20 15 10 5 0 1k 10k 100k Frequency (Hz) 1M 10M VS = ±5V 40 30 20 10 0 1 10 100 1k 10k 100k Load Capacitance (pF) Gain = +1 Gain = –1 Gain = –10 LARGE-SIGNAL STEP RESPONSE G = –1, CL = 1500pF SMALL-SIGNAL STEP RESPONSE G = +1, CL = 1000pF OPA227 OPA227 5µs/div 25mV/div 2V/div 400ns/div SMALL-SIGNAL STEP RESPONSE G = +1, CL = 5pF OPA227 25mV/div 400ns/div OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A www.ti.com 9 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted. MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 30 25 Output Voltage (Vp-p) SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 70 VS = ±15V OPA228 60 50 OPA228 Overshoot (%) 20 15 10 5 0 1k 10k 100k Frequency (Hz) 1M 10M VS = ±5V G = –100 40 30 G = +100 20 G = ±10 10 0 1 10 100 1k 10k 100k Load Capacitance (pF) LARGE-SIGNAL STEP RESPONSE G = –10, CL = 100pF SMALL-SIGNAL STEP RESPONSE G = +10, CL = 1000pF, RL = 1.8kΩ OPA228 OPA228 2µs/div 200mV/div 5V/div 500ns/div SMALL-SIGNAL STEP RESPONSE G = +10, CL = 5pF, RL = 1.8kΩ OPA228 200mV/div 500ns/div 10 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A APPLICATIONS INFORMATION The OPA227 and OPA228 series are precision op amps with very low noise. The OPA227 series is unity-gain stable with a slew rate of 2.3V/µs and 8MHz bandwidth. The OPA228 series is optimized for higher-speed applications with gains of 5 or greater, featuring a slew rate of 10V/µs and 33MHz bandwidth. Applications with noisy or high impedance power supplies may require decoupling capacitors close to the device pins. In most cases, 0.1µF capacitors are adequate. OFFSET VOLTAGE AND DRIFT The OPA227 and OPA228 series have very low offset voltage and drift. To achieve highest dc precision, circuit layout and mechanical conditions should be optimized. Connections of dissimilar metals can generate thermal potentials at the op amp inputs which can degrade the offset voltage and drift. These thermocouple effects can exceed the inherent drift of the amplifier and ultimately degrade its performance. The thermal potentials can be made to cancel by assuring that they are equal at both input terminals. In addition: • Keep thermal mass of the connections made to the two input terminals similar. • Locate heat sources as far as possible from the critical input circuitry. • Shield op amp and input circuitry from air currents such as those created by cooling fans. OPERATING VOLTAGE OPA227 and OPA228 series op amps operate from ±2.5V to ±18V supplies with excellent performance. Unlike most op amps which are specified at only one supply voltage, the OPA227 series is specified for real-world applications; a single set of specifications applies over the ±5V to ±15V supply range. Specifications are assured for applications between ±5V and ±15V power supplies. Some applications do not require equal positive and negative output voltage swing. Power supply voltages do not need to be equal. The OPA227 and OPA228 series can operate with as little as 5V between the supplies and with up to 36V between the supplies. For example, the positive supply could be set to 25V with the negative supply at –5V or vice-versa. In addition, key parameters are assured over the specified temperature range, –40°C to +85°C. Parameters which vary significantly with operating voltage or temperature are shown in the Typical Performance Curves. OFFSET VOLTAGE ADJUSTMENT The OPA227 and OPA228 series are laser-trimmed for very low offset and drift so most applications will not require external adjustment. However, the OPA227 and OPA228 (single versions) provide offset voltage trim connections on pins 1 and 8. Offset voltage can be adjusted by connecting a potentiometer as shown in Figure 1. This adjustment should be used only to null the offset of the op OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A 0.1µF V+ Trim range exceeds offset voltage specification 2 7 20kΩ 1 8 OPA227 3 4 0.1µF 6 OPA227 and OPA228 single op amps only. Use offset adjust pins only to null offset voltage of op amp. See text. V– FIGURE 1. OPA227 Offset Voltage Trim Circuit. amp. This adjustment should not be used to compensate for offsets created elsewhere in the system since this can introduce additional temperature drift. INPUT PROTECTION Back-to-back diodes (see Figure 2) are used for input protection on the OPA227 and OPA228. Exceeding the turn-on threshold of these diodes, as in a pulse condition, can cause current to flow through the input protection diodes due to the amplifier’s finite slew rate. Without external current-limiting resistors, the input devices can be destroyed. Sources of high input current can cause subtle damage to the amplifier. Although the unit may still be functional, important parameters such as input offset voltage, drift, and noise may shift. RF 500Ω – OPA227 Input + Output FIGURE 2. Pulsed Operation. When using the OPA227 as a unity-gain buffer (follower), the input current should be limited to 20mA. This can be accomplished by inserting a feedback resistor or a resistor in series with the source. Sufficient resistor size can be calculated: RX = VS/20mA – RSOURCE where RX is either in series with the source or inserted in the feedback path. For example, for a 10V pulse (VS = 10V), total loop resistance must be 500Ω. If the source impedance is large enough to sufficiently limit the current on its own, no additional resistors are needed. The size of any external resistors must be carefully chosen since they will increase noise. See the Noise Performance section of this data sheet for further information on noise calculation. Figure 2 shows an example implementing a currentlimiting feedback resistor. www.ti.com 11 INPUT BIAS CURRENT CANCELLATION The input bias current of the OPA227 and OPA228 series is internally compensated with an equal and opposite cancellation current. The resulting input bias current is the difference between with input bias current and the cancellation current. The residual input bias current can be positive or negative. When the bias current is cancelled in this manner, the input bias current and input offset current are approximately equal. A resistor added to cancel the effect of the input bias current (as shown in Figure 3) may actually increase offset and noise and is therefore not recommended. Conventional Op Amp Configuration R2 R1 NOISE PERFORMANCE Figure 4 shows total circuit noise for varying source impedances with the op amp in a unity-gain configuration (no feedback resistor network, therefore no additional noise contributions). Two different op amps are shown with total circuit noise calculated. The OPA227 has very low voltage noise, making it ideal for low source impedances (less than 20kΩ). A similar precision op amp, the OPA277, has somewhat higher voltage noise but lower current noise. It provides excellent noise performance at moderate source impedance (10kΩ to 100kΩ). Above 100kΩ, a FET-input op amp such as the OPA132 (very low current noise) may provide improved performance. The equation is shown for the calculation of the total circuit noise. Note that en = voltage noise, in = current noise, RS = source impedance, k = Boltzmann’s constant = 1.38 • 10–23 J/K and T is temperature in K. For more details on calculating noise, see the insert titled “Basic Noise Calculations.” Not recommended for OPA227 Op Amp RB = R2 || R1 External Cancellation Resistor 1.00+03 VOLTAGE NOISE SPECTRAL DENSITY vs SOURCE RESISTANCE Votlage Noise Spectral Density, E0 Typical at 1k (V/√Hz) EO OPA227 Recommended OPA227 Configuration R2 R1 1.00E+02 RS OPA277 1.00E+01 OPA227 Resistor Noise OPA277 Resistor Noise OPA227 EO2 = en2 + (in RS)2 + 4kTRS 1.00E+00 100 1k 10k 100k 10M No cancellation resistor. See text. Source Resistance, RS (Ω) FIGURE 3. Input Bias Current Cancellation. FIGURE 4. Noise Performance of the OPA227 in UnityGain Buffer Configuration. BASIC NOISE CALCULATIONS Design of low noise op amp circuits requires careful consideration of a variety of possible noise contributors: noise from the signal source, noise generated in the op amp, and noise from the feedback network resistors. The total noise of the circuit is the root-sum-square combination of all noise components. The resistive portion of the source impedance produces thermal noise proportional to the square root of the resistance. This function is shown plotted in Figure 4. Since the source impedance is usually fixed, select the op amp and the feedback resistors to minimize their contribution to the total noise. Figure 4 shows total noise for varying source impedances with the op amp in a unity-gain configuration (no feedback resistor network and therefore no additional noise contributions). The operational amplifier itself contributes both a voltage noise component and a current noise component. The voltage noise is commonly modeled as a time-varying component of the offset voltage. The current noise is modeled as the time-varying component of the input bias current and reacts with the source resistance to create a voltage component of noise. Consequently, the lowest noise op amp for a given application depends on the source impedance. For low source impedance, current noise is negligible and voltage noise generally dominates. For high source impedance, current noise may dominate. Figure 5 shows both inverting and noninverting op amp circuit configurations with gain. In circuit configurations with gain, the feedback network resistors also contribute noise. The current noise of the op amp reacts with the feedback resistors to create additional noise components. The feedback resistor values can generally be chosen to make these noise sources negligible. The equations for total noise are shown for both configurations. OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A 12 Noise in Noninverting Gain Configuration R2 Noise at the output:  R R 2 2 E O 2 = 1 + 2  e n 2 + e12 + e 2 2 + (i n R 2 ) + e S 2 + (i n R S ) 1 + 2  R1  R1    EO 2 2 R1  R Where eS = √4kTRS • 1 + 2  = thermal noise of RS R1   R  e1 = √4kTR1 •  2   R1  RS VS = thermal noise of R1 = thermal noise of R2 e2 = √4kTR2 Noise in Inverting Gain Configuration R2 Noise at the output:  R2  2 2 2 2 2 E O 2 = 1 +  e n + e1 + e 2 + (i n R 2 ) + e S R1 + R S   2 R1 EO RS VS  R2  Where eS = √4kTRS •   = thermal noise of RS  R1 + R S   R2  e1 = √4kTR1 •   = thermal noise of R1  R1 + R S  e2 = √4kTR2 = thermal noise of R2 For the OPA227 and OPA228 series op amps at 1kHz, en = 3nV/√Hz and in = 0.4pA/√Hz. FIGURE 5. Noise Calculation in Gain Configurations. OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A www.ti.com 13 R1 2MΩ R2 2MΩ R8 402kΩ R11 178kΩ R3 1kΩ R4 9.09kΩ R6 40.2kΩ R7 97.6kΩ C4 22nF R9 178kΩ U2 6 C5 0.47µF 3 R10 226kΩ C6 10nF 2 3 2 U3 6 VOUT C1 1µF C2 1µF U1 (OPA227) C3 0.47µF (OPA227) (OPA227) Input from Device Under Test R5 634kΩ FIGURE 6. 0.1Hz to 10Hz Bandpass Filter Used to Test Wideband Noise of the OPA227 and OPA228 Series. USING THE OPA228 IN LOW GAINS 22pF 100kΩ 10Ω 2 3 OPA227 6 VOUT The OPA228 family is intended for applications with signal gains of 5 or greater, but it is possible to take advantage of their high speed in lower gains. Without external compensation, the OPA228 has sufficient phase margin to maintain stability in unity gain with purely resistive loads. However, the addition of load capacitance can reduce the phase margin and destabilize the op amp. A variety of compensation techniques have been evaluated specifically for use with the OPA228. The recommended configuration consists of an additional capacitor (CF) in parallel with the feedback resistance, as shown in Figures 8 and 11. This feedback capacitor serves two purposes in compensating the circuit. The op amp’s input capacitance and the feedback resistors interact to cause phase shift that can result in instability. CF compensates the input capacitance, minimizing peaking. Additionally, at high frequencies, the closed-loop gain of the amplifier is strongly influenced by the ratio of the input capacitance and the feedback capacitor. Thus, CF can be selected to yield good stability while maintaining high speed. Device Under Test FIGURE 7. Noise Test Circuit. Figure 6 shows the 0.1Hz 10Hz bandpass filter used to test the noise of the OPA227 and OPA228. The filter circuit was designed using Texas Instruments’ FilterPro software (available at www.ti.com). Figure 7 shows the configuration of the OPA227 and OPA228 for noise testing. 14 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A Without external compensation, the noise specification of the OPA228 is the same as that for the OPA227 in gains of 5 or greater. With the additional external compensation, the output noise of the of the OPA228 will be higher. The amount of noise increase is directly related to the increase in high frequency closed-loop gain established by the CIN/ CF ratio. Figures 8 and 11 show the recommended circuit for gains of +2 and –2, respectively. The figures suggest approximate values for CF. Because compensation is highly dependent on circuit design, board layout, and load conditions, CF should be optimized experimentally for best results. Figures 9 and 10 show the large- and small-signal step responses for the G = +2 configuration with 100pF load capacitance. Figures 12 and 13 show the large- and smallsignal step responses for the G = –2 configuration with 100pF load capacitance. 22pF 15pF 2kΩ 2kΩ OPA228 2kΩ 100pF 1kΩ 2kΩ OPA228 2kΩ 100pF FIGURE 8. Compensation of the OPA228 for G =+2. FIGURE 11. Compensation for OPA228 for G = –2. 5mV/div 5mV/div OPA228 400ns/div OPA228 400ns/div FIGURE 9. Large-Signal Step Response, G = +2, CLOAD = 100pF, Input Signal = 5Vp-p. FIGURE 12. Large-Signal Step Response, G = –2, CLOAD = 100pF, Input Signal = 5Vp-p. 25mV/div 25mV/div OPA228 200ns/div OPA228 200ns/div FIGURE 10. Small-Signal Step Response, G = +2, CLOAD = 100pF, Input Signal = 50mVp-p. OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A FIGURE 13. Small-Signal Step Response, G = –2, CLOAD = 100pF, Input Signal = 50mVp-p. 15 www.ti.com 1.1kΩ 2.2nF 1.1kΩ VIN 33nF 1.65kΩ 1.43kΩ 1.91kΩ 2.21kΩ 68nF 1.43kΩ 330pF dc Gain = 1 OPA227 OPA227 VOUT 10nF fN = 13.86kHz Q = 1.186 fN = 20.33kHz Q = 4.519 f = 7.2kHz FIGURE 14. Three-Pole, 20kHz Low Pass, 0.5dB Chebyshev Filter. 0.1µF 20pF TTL INPUT GAIN +1 –1 100Ω 100kΩ “1” “0” 9.76kΩ Balance Trim 2 3 OPA227 6 Output 500Ω Input D1 10kΩ 4.99kΩ S1 S2 2 3 OPA227 8 1 4.75kΩ TTL In DG188 Offset Trim 1kΩ 6 Output Dexter 1M Thermopile Detector NOTE: Use metal film resistors and plastic film capacitor. Circuit must be well shielded to achieve low noise. D2 4.75kΩ Responsivity ≈ 2.5 x 104V/W Output Noise ≈ 30µVrms, 0.1Hz to 10Hz +VCC FIGURE 15. Long-Wavelength Infrared Detector Amplifier. FIGURE 16. High Performance Synchronous Demodulator. 16 OPA227, 2227, 4227 OPA228, 2228, 4228 www.ti.com SBOS110A +15V 0.1µF 1kΩ 1kΩ Audio In 1/2 OPA2227 200Ω 200Ω To Headphone 1/2 OPA2227 This application uses two op amps in parallel for higher output current drive. 0.1µF –15V FIGURE 17. Headphone Amplifier. Bass Tone Control R1 7.5kΩ R2 50kΩ 3 CW 1 2 R3 7.5kΩ R10 100kΩ Midrange Tone Control C1 940pF R4 2.7kΩ VIN R5 50kΩ 3 CW 1 2 R6 2.7kΩ C2 0.0047µF Treble Tone Control R7 7.5kΩ R8 50kΩ 3 CW 1 2 R9 7.5kΩ R11 100kΩ C3 680pF 2 3 OPA227 6 VOUT FIGURE 18. Three-Band ActiveTone Control (bass, midrange and treble). OPA227, 2227, 4227 OPA228, 2228, 4228 SBOS110A www.ti.com 17 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2007 PACKAGING INFORMATION Orderable Device OPA2227P OPA2227PA OPA2227PAG4 OPA2227PG4 OPA2227U OPA2227U/2K5 OPA2227U/2K5E4 OPA2227U/2K5G4 OPA2227UA OPA2227UA/2K5 OPA2227UA/2K5E4 OPA2227UAE4 OPA2227UAG4 OPA2227UE4 OPA2227UG4 OPA2228P OPA2228PA OPA2228PAG4 OPA2228PG4 OPA2228U OPA2228U/2K5 OPA2228U/2K5E4 OPA2228UA OPA2228UA/2K5 OPA2228UA/2K5E4 Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type PDIP PDIP PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC Package Drawing P P P P D D D D D D D D D D D P P P P D D D D D D Pins Package Eco Plan (2) Qty 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 50 50 50 50 100 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR 2500 Green (RoHS & no Sb/Br) 2500 Pb-Free (RoHS) 2500 Green (RoHS & no Sb/Br) 100 2500 Green (RoHS & no Sb/Br) Pb-Free (RoHS) 2500 Green (RoHS & no Sb/Br) 100 100 100 100 50 50 50 50 100 2500 2500 100 2500 2500 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2007 Orderable Device OPA2228UAE4 OPA2228UE4 OPA227P OPA227PA OPA227PAG4 OPA227PG4 OPA227U OPA227U/2K5 OPA227U/2K5E4 OPA227UA OPA227UA/2K5 OPA227UA/2K5G4 OPA227UAG4 OPA227UE4 OPA228P OPA228PA OPA228PAG4 OPA228PG4 OPA228U OPA228UA OPA228UA/2K5 OPA228UA/2K5E4 OPA228UAG4 OPA228UG4 OPA4227PA OPA4227PAG4 Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type SOIC SOIC PDIP PDIP PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP Package Drawing D D P P P P D D D D D D D D P P P P D D D D D D N N Pins Package Eco Plan (2) Qty 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 14 14 100 100 50 50 50 50 100 2500 2500 100 Pb-Free (RoHS) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-3-260C-168 HR Level-3-260C-168 HR N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR N / A for Pkg Type N / A for Pkg Type 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 100 100 50 50 50 50 100 100 2500 2500 100 100 25 25 Green (RoHS & no Sb/Br) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2007 Orderable Device OPA4227UA OPA4227UA/2K5 OPA4227UA/2K5G4 OPA4227UAG4 OPA4228PA OPA4228UA OPA4228UA/2K5 OPA4228UAE4 (1) Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type SOIC SOIC SOIC SOIC PDIP SOIC SOIC SOIC Package Drawing D D D D N D D D Pins Package Eco Plan (2) Qty 14 14 14 14 14 14 14 14 58 Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 58 25 58 2500 58 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) 0.400 (10,60) 0.355 (9,02) 8 5 PLASTIC DUAL-IN-LINE 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.010 (0,25) NOM Gage Plane 0.020 (0,51) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M 0.430 (10,92) MAX 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated