OPA2342UAG4

OPA OPA342 OPA2342 OPA4342 434 2 OPA 342 OPA 234 2 OPA ® 342 OPA 434 2 www.ti.com Low-Cost, Low-Power, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifier ™ Series FEATURES DESCRIPTION LOW QUIESCENT CURRENT: 150µA typ RAIL-TO-RAIL INPUT RAIL-TO-RAIL OUTPUT (within 1mV) SINGLE SUPPLY CAPABILITY LOW COST MicroSIZE PACKAGE OPTIONS: SOT23-5 MSOP-8 TSSOP-14 ● BANDWIDTH: 1MHz ● SLEW RATE: 1V/µs ● THD + NOISE: 0.006% The OPA342 series rail-to-rail CMOS operational amplifiers are designed for low-cost, low-power, miniature applications. They are optimized to operate on a single supply as low as 2.5V with an input commonmode voltage range that extends 300mV beyond the supplies. Rail-to-rail input/output and high-speed operation make them ideal for driving sampling Analog-to-Digital Converters (ADC). They are also well suited for generalpurpose and audio applications and providing I/V conversion at the output of Digital-to-Analog Converters (DAC). Single, dual, and quad versions have identical specs for design flexibility. The OPA342 series offers excellent dynamic response with a quiescent current of only 250µA max. Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction. ● ● ● ● ● ● APPLICATIONS ● ● ● ● ● ● ● ● COMMUNICATIONS PCMCIA CARDS DATA ACQUISITION PROCESS CONTROL AUDIO PROCESSING ACTIVE FILTERS TEST EQUIPMENT CONSUMER ELECTRONICS PACKAGE SINGLE OPA342 SOT23-5 ✔ QUAD OPA4342 ✔ MSOP-8 SO-8 DUAL OPA2342 ✔ ✔ TSSOP-14 ✔ SO-14 ✔ DIP-14 ✔ SPICE MODEL available at www.burr-brown.com. Copyright © 2000, Texas Instruments Incorporated SBOS106A Printed in U.S.A. August, 2000 SPECIFICATIONS: VS = 2.7V to 5.5V At TA = +25°C, RL = 10kΩ connected to VS /2 and VOUT = VS /2, unless otherwise noted. Boldface limits apply over the temperature range, TA = –40°C to +85°C. OPA342NA, UA OPA2342EA, UA OPA4342EA, UA, PA PARAMETER OFFSET VOLTAGE Input Offset Voltage TA = –40°C to +85°C vs Temperature vs Power Supply TA = –40°C to +85°C Channel Separation, dc f = 1kHz CONDITION VOS dVOS/dT PSRR VCM = VS /2 VS = 2.7V to 5.5V, VCM < (V+) -1.8V VS = 2.7V to 5.5V, VCM < (V+) -1.8V ±6 ±6 mV mV µV/°C µV/V µV/V µV/V dB 200 250 8 30 0.5 VCM CMRR CMRR CMRR AOL FREQUENCY RESPONSE Gain-Bandwidth Product GBW Slew Rate SR Settling Time, 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise, f = 1kHz THD+N OUTPUT Voltage Output Swing from Rail(2) TA = –40°C to +85°C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT23-5 Surface Mount MSOP-8 Surface Mount SO-8 Surface Mount TSSOP-14 Surface Mount SO-14 Surface Mount DIP-14 ±1 ±1 ±3 30 en in TA = –40°C to +85°C POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) TA = –40°C to +85°C UNITS IOS VS = +5.5V, –0.3V < VCM < (V+) - 1.8 VS = +5.5V, –0.3V < VCM < (V+) - 1.8 VS = +5.5V, –0.3V < VCM < 5.8V VS = +5.5V, –0.3V < VCM < 5.8V VS = +2.7V, –0.3V < VCM < 3V VS = +2.7V, –0.3V < VCM < 3V –0.3 76 74 66 64 62 60 INPUT IMPEDANCE Differential Common-Mode TA = –40°C to +85°C Short-Circuit Current Capacitive Load Drive MAX ±0.2 See Typical Curve ±0.2 IB NOISE Input Voltage Noise, f = 0.1Hz to 50kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz OPEN-LOOP GAIN Open-Loop Voltage Gain TA = –40°C to +85°C TYP 0.2 132 INPUT BIAS CURRENT Input Bias Current TA = –40°C to +85°C Input Offset Current INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio TA = –40°C to +85°C Common-Mode Rejection Ratio TA = –40°C to +85°C Common-Mode Rejection Ratio TA = –40°C to +85°C MIN ISC CLOAD RL = 100kΩ, 10mV < VO < (V+) – 10mV RL = 100kΩ, 10mV < VO < (V+) – 10mV RL = 5kΩ, 400mV < VO < (V+) – 400mV RL = 5kΩ, 400mV < VO < (V+) – 400mV CL = 100pF G=1 RL = 100kΩ, AOL ≥ 96dB RL = 100kΩ, AOL ≥ 104dB RL = 100kΩ, AOL ≥ 100dB RL = 5kΩ, AOL ≥ 96dB RL = 5kΩ, AOL ≥ 90dB Per Channel pA pA pA ±10 µVrms nV/√Hz fA/√Hz (V+) + 0.3 V dB dB dB dB dB dB 88 78 74 1013 || 3 1013 || 6 Ω || pF Ω || pF 124 dB dB dB dB 114 1 1 5 8 2.5 0.006 VS = 5.5V, 2V Step VS = 5.5V, 2V Step VIN • G = VS VS = 5.5V, VO = 3Vp-p(1), G = 1 VS IQ 104 100 96 90 ±10 MHz V/µs µs µs µs % 1 3 mV mV mV mV mV mA 10 10 400 400 20 ±15 See Typical Curve 2.7 5.5 2.5 to 5.5 150 IO = 0A –40 –55 –65 θJA 250 300 V V µA µA +85 +125 +150 °C °C °C °C/W °C/W °C/W °C/W °C/W °C/W 200 150 150 100 100 100 NOTES: (1) VOUT = 0.25V to 3.25V. (2) Output voltage swings are measured between the output and power-supply rails. 2 OPA342, 2342, 4342 SBOS106A ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage, V+ to V- ................................................................... 7.5V Signal Input Terminals, Voltage(2) ..................... (V–) –0.5V to (V+) +0.5V Current(2) .................................................... 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. –55°C to +125°C Storage Temperature ..................................................... –65°C to +150°C Junction Temperature ...................................................................... 150°C Lead Temperature (soldering, 10s) ................................................. 300°C ESD Tolerance (Human Body Model) ............................................ 4000V This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only. Functional operation of the device at these conditions, or beyond the specified operating conditions, is not implied. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current-limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER OPA342NA SOT23-5 331 –40°C to +85°C B42 " " " " OPA342UA " OPA342UA SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA OPA342NA/250 OPA342NA /3K OPA342UA OPA342UA /2K5 Tape and Reel Tape and Reel Rails Tape and Reel OPA2342EA /250 OPA2342EA /2K5 OPA2342UA OPA2342UA /2K5 Tape and Reel Tape and Reel Rails Tape and Reel OPA4342EA /250 OPA4342EA /2K5 OPA4342UA OPA4342UA /2K5 OPA4342PA Tape and Reel Tape and Reel Rails Tape and Reel Rails SO-8 182 –40°C to +85°C " " " " " OPA2342EA MSOP-8 337 –40°C to +85°C C42 " " " " " OPA2342UA SO-8 182 –40°C to +85°C OPA2342UA " " " " " OPA4342EA TSSOP-14 357 –40°C to +85°C OPA4342EA " " " " " OPA4342UA SO-14 235 –40°C to +85°C OPA4342UA " " " " " OPA4342PA DIP-14 010 –40°C to +85°C OPA4342PA NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /3K indicates 3000 devices per reel). Ordering 3000 pieces of “OPA342NA/3K” will get a single 3000-piece Tape and Reel. PIN CONFIGURATIONS OPA342 Out 1 V– 2 +In 3 5 4 OPA4342 V+ –In Out A 1 –In A 2 A 14 Out D 13 –In D D +In A 3 12 +In D +V 4 11 –V +In B 5 10 +In C SOT23-5 OPA342 OPA2342 NC 1 8 NC Out A 1 –In 2 7 V+ –In A 2 +In 3 6 Out +In A 3 V– 4 5 NC V– 4 A B B C 8 V+ –In B 6 9 –In C 7 Out B Out B 7 8 Out C 6 –In B 5 +In B TSSOP-14, SO-14, DIP-14 SO-8 OPA342, 2342, 4342 SBOS106A SO-8, MSOP-8 3 TYPICAL PERFORMANCE CURVES At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. POWER SUPPLY AND COMMON-MODE REJECTION RATIO vs FREQUENCY OPEN-LOOP GAIN/PHASE vs FREQUENCY 100 100 30 80 +PSRR Phase 80 60 60 90 40 120 Phase (°) Gain (dB) 0 Gain 20 Rejection Ratio (dB) 120 0.1 10 1 100 1k 10k 100k 1M 60 40 20 150 0 CMRR –PSRR 10 180 10M 10 100 Channel Separation (dB) Maximum Output Voltage (Vp-p) VS = +5.5V 5 VS = +5V 4 3 VS = +2.7V 2 1 120 100 Dual and quad devices. G = 1, all channels. Quad measured channel A to D or B to C—other combinations yield improved rejection. 80 60 100k 10k 100 1M 100k VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY VN 100 1 10 100 1k 10k Frequency (Hz) 100k 1M 0.1 10M 0.1 THD+N (%) 10 1M 1 Current Noise (fA/√Hz) IN 1000 10 10k Frequency (Hz) 100 1 1k Frequency (Hz) 10000 Voltage Noise (nV/√Hz) 100k 140 0 4 10k CHANNEL SEPARATION vs FREQUENCY MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 6 1k Frequency (Hz) Frequency (Hz) 0.010 0.001 20 100 1k 10k 20k Frequency (Hz) OPA342, 2342, 4342 SBOS106A TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN, COMMON-MODE REJECTION RATIO, AND POWER SUPPLY REJECTION vs TEMPERATURE INPUT BIAS CURRENT vs TEMPERATURE 140 10000 AOL Input Bias Current (pA) AOL, CMRR, PSRR (dB) 120 100 CMRR 80 PSRR 60 40 20 0 1000 100 10 1 0.1 –75 –50 –25 0 25 50 75 100 125 150 –75 –50 –25 Temperature (°C) 0 25 50 75 100 125 Temperature (°C) QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs TEMPERATURE SLEW RATE vs TEMPERATURE 200 40 1.2 175 35 1 30 135 25 +ISC 100 20 –ISC 75 15 50 10 25 5 0 –75 –50 25 0 –25 50 75 100 Slew Rate (V/µs) IQ 150 Short-Circuit Current (mA) Quiescent Current (µA) –SR 0.8 +SR 0.6 0.4 0.2 0 0 125 –75 –50 –25 0 25 50 75 100 Temperature (°C) Temperature (°C) INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE 125 160 6 20 V– Supply 2 V+ Supply Quiescent Current (µA) Input Bias Current (pA) 4 0 –2 Input voltage ≤ –0.3V can cause op amp output to lock up. See text. –4 155 15 –ISC 150 10 IQ 145 5 140 –6 –1 0 1 2 3 4 Common-Mode Voltage (V) OPA342, 2342, 4342 SBOS106A 5 6 Short-Circuit Current (mA) +ISC 0 2 3 4 5 6 Supply Voltage (V) 5 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN vs OUTPUT VOLTAGE SWING OUTPUT VOLTAGE SWING vs OUTPUT CURRENT V+ 120 –40°C (V+) – 2 2 85°C 25°C ≈ ≈ 25°C –40°C 1 85°C Open-Loop Gain (dB) Output Voltage (V) (V+) – 1 0 RL = 100kΩ 100 RL = 5kΩ 90 80 5 0 10 15 120 20 100 80 60 40 20 Output Current (mA) Output Voltage Swing from Rail (mV) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 24 16 12 8 4 0 18 Typical production distribution of packaged units. 16 Percent of Amplifiers (%) Typical production distribution of packaged units. 20 Percent of Amplifiers (%) 110 14 12 10 8 6 4 2 0 –6 –5.4 –4.8 –4.2 –3.6 –3 –2.4 –1.8 –1.2 –0.6 0 0.6 1.2 1.8 2.4 3 3.6 4.2 4.8 5.4 6 –10 –9 –8 –7 –6 –5 –4 –3 –2 –1 0 1 2 3 4 5 6 7 8 9 10 0 Offset Voltage (mV) Offset Voltage Drift (µV/°C) QUIESCENT CURRENT PRODUCTION DISTRIBUTION SETTLING TIME vs CLOSED-LOOP GAIN 400 350 20 300 Settling Time (µs) Percent of Amplifiers (%) 24 16 12 8 250 0.01% 200 150 100 0.1% 4 50 0