PCM1850APJTG4

Burr Brown Products from Texas Instruments PCM1850A PCM1851A SLES173 – MARCH 2006 24-BIT, 96-kHz STEREO A/D CONVERTER WITH 6 × 2-CHANNEL MUX AND PGAE FEATURES • Multiplexer and Programmable-Gain Amplifier (PGA) – 6×2-Channel Single-Ended Inputs – Multiplexed Output – Maximum Input Level: 2.4 V rms – Input Resistance: 50 kΩ, Minimum – PGA Gain: 11-dB to –11-dB Range, 0.5 dB/Step 24-Bit Delta-Sigma Stereo A/D Converter Antialiasing Filter Included Oversampling Decimation Filter – Oversampling Frequency: ×64 – Pass-Band Ripple: ±0.05 dB – Stop-Band Attenuation: –65 dB – On-Chip High-Pass Filter: 0.91 Hz (48 kHz) High Performance – THD+N: 0.0023% (Typically) – SNR: 101 dB (Typically) – Dynamic Range: 102 dB (Typically) • PCM Audio Interface – Master/Slave Mode Selectable – Data Formats: 24-Bit Left-Justified, 24-Bit I2S, 16-, 24-Bit Right-Justified Mode Control by Serial Interface: – With SPI Control (PCM1850A) – With I2C Control (PCM1851A) Sampling Rate: 16–96 kHz System Clock: 256 fs, 384 fs, 512 fs, 768 fs Dual Power Supplies: 5 V for Analog, 3.3 V for Digital Package: 32-Pin TQFP • • • • • • • • • • • • • • APPLICATIONS DVD/HDD/DVD+HDD Recorder AV Amplifier Receiver CD Recorder MD Recorder Multitrack Recorder Electric Musical Instrument • DESCRIPTION The PCM1850A/1851A is a high-performance, low-cost, single-chip stereo analog-to-digital converter with a single-ended analog front end that consists of a 6-stereo-input multiplexer and wide-range PGA. The PCM1850A/1851A includes a delta-sigma modulator with 64-times oversampling, a digital decimation filter and a low-cut filter that removes the dc component of the input signal. For various applications, the PCM1850A/1851A supports two modes (master and slave) and four data formats through a serial control interface, SPI for the PCM1850A and I2C for the PCM1851A. The PCM1850A/1851A is suitable for a wide variety of cost-sensitive DVD/CD/MD recorder and receiver applications where good performance and operation from a 5-V analog supply and 3.3-V digital supply is required. The PCM1850A/1851A is fabricated using a highly advanced CMOS process and is available in a small 32-pin TQFP package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. System Two, Audio Precision are trademarks of Audio Precision, Inc. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006, Texas Instruments Incorporated PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. BLOCK DIAGRAM VINL1 VINL2 VINL3 VINL4 VINL5 VINL6 MOUTL Single-Ended MUX and PGA Delta-Sigma Modulator BCK LRCK DOUT Audio Data Interface VREF1 VREFS VREF2 Reference Decimation Filter with High-Pass Filter OVER VINR1 VINR2 VINR3 VINR4 VINR5 VINR6 MOUTR Control Data Interface MS (ADR)(1) MD (SDA)(1) MC (SCL)(1) Single-Ended MUX and PGA Delta-Sigma Modulator TEST0 TEST1 RST Power Supply Clock and Timing Control SCKI VCC (1) AGND DGND VDD B0004-09 PCM1850A (PCM1851A) PIN ASSIGNMENTS PCM1850A (TOP VIEW) PCM1851A (TOP VIEW) VINR6 VINL6 VINR5 VINL5 VINR4 VINL4 VINR3 VINL3 24 23 22 21 20 19 18 17 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 VREFS VREF1 VREF2 Vcc AGND MS MC MD 25 26 27 28 29 30 31 32 1 234 5678 VINR2 VINL2 VINR1 VINL1 MOUTL MOUTR RST TEST1 VREFS VREF1 VREF2 Vcc AGND ADR SCL SDA VINR6 VINL6 VINR5 VINL5 VINR4 VINL4 VINR3 VINL3 25 26 27 28 29 30 31 32 12 3456 78 16 15 14 13 12 11 10 9 VINR2 VINL2 VINR1 VINL1 MOUTL MOUTR RST TEST1 LRCK BCK DOUT OVER DGND VDD SCKI TEST0 LRCK BCK DOUT OVER DGND VDD SCKI TEST0 P0040-01 2 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 TERMINAL FUNCTIONS PCM1850A TERMINAL NAME AGND BCK DGND DOUT LRCK MC MD MOUTL MOUTR MS OVER RST SCKI TEST0 TEST1 VCC VDD VINL1 VINL2 VINL3 VINL4 VINL5 VINL6 VINR1 VINR2 VINR3 VINR4 VINR5 VINR6 VREFS VREF1 VREF2 (1) (2) (3) NO. 29 2 5 3 1 31 32 12 11 30 4 10 7 8 9 28 6 13 15 17 19 21 23 14 16 18 20 22 24 25 26 27 I/O — I/O — O I/O I I O O I O I I I I — — I I I I I I I I I I I I — — — Analog GND Bit clock input/output (1) Digital GND Audio data output Sampling clock input/output (1) Mode-control clock input (2) Mode-control data input(2) Multiplexer output, L-channel Multiplexer output, R-channel Mode-control select input (3) Overflow flag Reset, active-LOW(3) System clock input; 256 fS, 384 fS, 512 fS, or 768 fS(2) Test 0, must be connected to GND(3) Test 1, must be connected to GND(3) Analog power supply, 5-V Digital power supply, 3.3-V Analog input 1, L-channel Analog input 2, L-channel Analog input 3, L-channel Analog input 4, L-channel Analog input 5, L-channel Analog input 6, L-channel Analog input 1, R-channel Analog input 2, R-channel Analog input 3, R-channel Analog input 4, R-channel Analog input 5, R-channel Analog input 6, R-channel Reference S decoupling capacitor (= 0.5 VCC) Reference 1 decoupling capacitor (= 0.5 VCC) Reference 2 decoupling capacitor (= VCC) DESCRIPTION Schmitt-trigger input with internal pulldown resistor (50 kΩ, typically) Schmitt-trigger input, 5-V tolerant Schmitt-trigger input with internal pulldown resistor (50 kΩ, typically), 5-V tolerant Submit Documentation Feedback 3 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com PCM1851A TERMINAL NAME ADR AGND BCK DGND DOUT LRCK MOUTL MOUTR OVER RST SCKI SCL SDA TEST0 TEST1 VCC VDD VINL1 VINL2 VINL3 VINL4 VINL5 VINL6 VINR1 VINR2 VINR3 VINR4 VINR5 VINR6 VREFS VREF1 VREF2 (1) (2) (3) (4) NO. 30 29 2 5 3 1 12 11 4 10 7 31 32 8 9 28 6 13 15 17 19 21 23 14 16 18 20 22 24 25 26 27 I/O I — I/O — O I/O O O O I I I I/O I I — — I I I I I I I I I I I I — — — Mode control address select input (1) Analog GND Bit clock input/output (2) Digital GND Audio data output Sampling clock input/output (2) Multiplexer output, L-channel Multiplexer output, R-channel Overflow flag Reset, active-LOW(1) System clock input; 256 fS, 384 fS, 512 fS, or 768 fS (3) Mode-control clock input(3) Mode-control data input/output (4) Test 0, must be connected to GND(1) Test 1, must be connected to GND(1) Analog power supply, 5-V Digital power supply, 3.3-V Analog input 1, L-channel Analog input 2, L-channel Analog input 3, L-channel Analog input 4, L-channel Analog input 5, L-channel Analog input 6, L-channel Analog input 1, R-channel Analog input 2, R-channel Analog input 3, R-channel Analog input 4, R-channel Analog input 5, R-channel Analog input 6, R-channel Reference S decoupling capacitor (= 0.5 VCC) Reference 1 decoupling capacitor (= 0.5 VCC) Reference 2 decoupling capacitor (= VCC) DESCRIPTION Schmitt-trigger input with internal pulldown resistor (50 kΩ, typically), 5-V tolerant Schmitt-trigger input with internal pulldown resistor (50 kΩ, typically) Schmitt-trigger input, 5-V tolerant Schmitt-trigger input/open-drain LOW output, 5-V tolerant 4 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 (1) ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) VALUE VCC VDD Supply voltage Ground voltage differences: AGND, DGND Digital input voltage: LRCK, BCK, DOUT, OVER Digital input voltage: RST, SCKI, MS (ADR) (2), MC (SCL) (2), MD (SDA) (2), TEST0, TEST1 Analog input voltage: VINL1–6, VINR1–6 Analog input voltage: MOUTL, MOUTR, VREF1, VREF2, VREFS Input current (any pins except supplies) Ambient temperature under bias Storage temperature Junction temperature Lead temperature (soldering) Package temperature (IR reflow, peak) (1) (2) –0.3 to 6.5 –0.3 to 4 ±0.1 –0.3 to (VDD + 0.3) < 4 –0.3 to 6.5 –3 to (VCC + 3) < 9 –0.3 to (VCC + 0.3) < 6.5 ±10 –40 to 125 –55 to 150 150 260°C, 5 s 260 °C UNIT V V V V V V V mA °C °C °C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. PCM1850A (PCM1851A) RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN VCC VDD Analog supply voltage Digital supply voltage Analog input voltage, full scale (0 dB) Digital input logic family Digital input clock frequency Digital output load capacitance TA Operating free-air temperature 40 System clock Sampling clock 4.096 16 VCC = 5 V, PGA gain = 5.5 dB 4.5 2.7 NOM 5 3.3 2 TTL 49.152 96 20 85 MHz kHz pF °C MAX 5.5 3.6 UNIT V V Vrms ELECTRICAL CHARACTERISTICS All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted) PARAMETER DIGITAL INPUT/OUTPUT — DATA FORMAT Audio data interface format Audio data bit length Audio data format fS Sampling frequency 256 fS System clock frequency 384 fS 512 fS 768 fS 16 4.096 6.144 8.192 12.288 Left-justified, I2S, right-justified 16, 24 MSB-first, 2s complement 48 12.288 18.432 24.576 36.864 96 24.576 36.864 49.152 – MHz kHz bits TEST CONDITIONS PCM1850APJT, PCM1851APJT MIN TYP MAX UNIT Submit Documentation Feedback 5 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com ELECTRICAL CHARACTERISTICS (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted) PARAMETER INPUT LOGIC VIH (1) VIL VIL IIH (1) TEST CONDITIONS PCM1850APJT, PCM1851APJT MIN 2 TYP MAX VDD 0.8 5.5 0.8 ±10 ±10 65 100 ±10 2.8 0.5 6 2 2.4 UNIT VIH (2) (3) (2) (3) (2) Input logic level 0 2 0 VIN = VDD VIN = 0 VIN = VDD VIN = 0 IOUT = –4 mA IOUT = 4 mA VDC IIL (2) IIH (1) (3) IIL (1) (3) Input logic current µA OUTPUT LOGIC VOH (4) VOL (4) (5) Output logic level VDC AFE MULTPLEXER Input channels Input level for full scale Center voltage (VREF1) Center voltage (VREFS) Input impedance AFE PGA Gain range Gain step Monotonicity Antialiasing filter frequency response MONITOR OUTPUT Output level for full scale Output load THD+N S/N (6) (7) (6) (7) Vrms V V kΩ Selected channel Unselected channel Selected channel Unselected channel 50 50 –11 0.5 VCC 0.5 VCC 169 57 0 0.5 Specified 300 11 dB dB kHz –3 dB, PGA gain = –5.5 dB AC-coupled, >10 kΩ AC-coupled AC-coupled, 10 kΩ, 3 Vp-p output AC-coupled, 10 kΩ AC-coupled, 10 kΩ 10 0.6 VCC 0.0016% 104 –3 0.5 VCC 24 0.6 VCC Vp-p kΩ dB % of FSR V bits Vp-p Signal-to-noise ratio Gain error (6) (7) Center voltage ADC Resolution Full-scale input voltage (1) (2) (3) (4) (5) (6) (7) Pins 1, 2: LRCK, BCK (In slave mode, Schmitt-trigger input, with 50-kΩ typical pulldown resistor) Pins 7, 31, 32: SCKI, MC/SCL (PCM1850A/1851A), MD/SDA (PCM1850A/1851A) (Schmitt-trigger input, 5-V tolerant) Pins 8–10, 30: TEST0, TEST1, RST, MS/ADR (PCM1850A/1851A) (Schmitt-trigger input, with 50-kΩ typical pulldown resistor, 5-V tolerant) Pins 1–4: LRCK, BCK (in master mode), DOUT, OVER Pin 32: SDA (PCM1851A) (open-drain LOW output) Analog performance specifications are tested with the System Two™ audio measurement system by Audio Precision™, using a 400-Hz HPF and 20-kHz LPF in the RMS mode at fIN = 1 kHz. Reference level (0 dB) is specified as 2-V rms input on VINL[1:6] and VINR[1:6] pins with PGA gain of –5.5 dB. 6 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 ELECTRICAL CHARACTERISTICS (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted) PARAMETER ACCURACY Gain mismatch, channel-to-channel Gain error Bipolar zero error DYANAMIC PERFORMANCE (1) (2) TEST CONDITIONS PCM1850APJT, PCM1851APJT MIN TYP ±1 ±2 MAX ±3 ±5 UNIT % of FSR % of FSR % of FSR High-pass filter bypass fS = 48 kHz, VIN = –0.5 dB (1.89 Vrms) ±2 0.0023% 0.0027% 1% 1% 96 96 92 102 102 101 102 98 100 90 96 96 0.454 fS 0.583 fS ±0.05 –65 17.4/fS 0.004% THD+N Total harmonic distortion + noise (3) fS = 96 kHz (4), VIN = –0.5 dB (1.89 Vrms) fS = 48 kHz, VIN = –60 dB (2 mVrms) fS = 96 kHz (4), VIN = –60 dB (2 mVrms) A-weighted A-weighted Dynamic range S/N (3) fS = 48 kHz, A-weighted fS = 96 kHz (3) (4), dB dB dB dB Signal-to-noise ratio fS = 48 kHz, A-weighted fS = 96 kHz fS = 48 kHz (3) (4), Channel separation (between L-ch and R-ch) fS = 96 kHz fS = 48 kHz fS = 96 kHz (4) Channel separation (among channels) (5) DIGITAL FILTER PERFORMANCE Pass band Stop band Pass-band ripple Stop-band attenuation Delay time HPF frequency response (1) (2) (3) (4) (5) (4) Hz Hz dB dB s mHz –3 dB 0.019 fS Analog performance specifications are tested with the System Two™ audio measurement system by Audio Precision™, using a 400-Hz HPF and 20-kHz LPF in the RMS mode at fIN = 1 kHz. Reference level (0 dB) is specified as 2-V rms input on VINL[1:6] and VINR[1:6] pins with PGA gain of –5.5 dB. Unselected channel inputs are terminated to AGND with 0.33 µF. fS = 96 kHz, system clock = 256 fS. 2-V rms input is applied to all unselected channels, and input of selected channel is terminated to AGND with 0.33 µF. Submit Documentation Feedback 7 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com ELECTRICAL CHARACTERISTICS (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted) PARAMETER POWER-SUPPLY REQUIREMENTS VCC VDD ICC Supply current IDD (1) TEST CONDITIONS PCM1850APJT, PCM1851APJT MIN 4.5 2.7 TYP 5 3.3 28 190 6 10 12 MAX 5.5 3.6 35 UNIT Voltage range Operational Powered down fS = 48 kHz fS = 96 kHz (3) (2), (2), (2) VDC mA µA mA µA Powered down Powered down PCM1850A PCM1851A (3) 80 280 160 180 1.2 1.9 –40 80 85 208 Operating, fS = 48 kHz Power dissipation Operating, fS = 96 kHz Powered down Powered down TEMPERATURE RANGE Operation temperature Thermal resistance (θJA) (1) (2) (3) Minimum load on DOUT (pin 3), BCK (pin 2), LRCK (pin 1) Halt SCKI, BCK, LRCK. fS = 96 kHz, system clock = 256 fS. (2), (2), PCM1850A PCM1851A mW °C °C/W 8 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 TYPICAL PERFORMANCE CURVES OF INTERNAL FILTER All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted). DIGITAL FILTER Decimation Filter Frequency Response AMPLITUDE vs FREQUENCY 50 AMPLITUDE vs FREQUENCY 0 −10 0 −20 −30 Amplitude – dB −50 Amplitude – dB 0 8 16 Frequency [× fS] 24 32 G001 −40 −50 −60 −70 −100 −150 −80 −90 −200 −100 0.00 0.25 0.50 Frequency [× fS] 0.75 1.00 G002 Figure 1. Overall Characteristics AMPLITUDE vs FREQUENCY 0.2 0 Figure 2. Stop-Band Attenuation Characteristics AMPLITUDE vs FREQUENCY –4.13 dB at 0.5× −1 0.0 −2 −3 Amplitude − dB 0.1 0.2 0.3 0.4 0.5 0.6 G003 Amplitude – dB −0.2 −4 −5 −6 −7 −8 −9 −0.4 −0.6 −0.8 −1.0 0.0 −10 0.45 0.47 0.49 0.51 0.53 0.55 G004 Frequency [× fS] Frequency [× fS] Figure 3. Pass-Band Ripple Characteristics Figure 4. Transition-Band Characteristics Submit Documentation Feedback 9 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com TYPICAL PERFORMANCE CURVES OF INTERNAL FILTER (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted). High-Pass Filter Frequency Response AMPLITUDE vs FREQUENCY 0.2 0 −10 0.0 −20 −30 Amplitude – dB −40 −50 −60 −70 −80 −90 −1.0 0 1 2 Frequency [× fS/1000] 3 4 G005 AMPLITUDE vs FREQUENCY Amplitude – dB −0.2 −0.4 −0.6 −0.8 −100 0.0 0.1 0.2 Frequency [× fS/1000] 0.3 0.4 G006 Figure 5. HPF Pass-Band Characteristics Figure 6. HPF Stop-Band Characteristics ANALOG FILTER Antialiasing Filter Frequency Response (at PGA Gain = –5.5 dB) AMPLITUDE vs FREQUENCY −5.5 −5.6 −5.7 −5.8 Amplitude – dB Amplitude – dB −5.9 −6.0 −6.1 −6.2 −6.3 −6.4 −6.5 0.1 0 −5 −10 −15 −20 −25 −30 −35 −40 −45 −50 1 10 f – Frequency – kHz G007 AMPLITUDE vs FREQUENCY f–3dB = 300 kHz 100 1k 1 10 100 f – Frequency – kHz 1k 10k G008 Figure 7. Antialiasing Filter Pass-Band Characteritics Figure 8. Antialiasing Filter Stop-Band Characteritics 10 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 TYPICAL PERFORMANCE CURVES AT PGA GAIN = –5.5 dB All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted). TOTAL HARMONIC DISTORTION + NOISE vs FREE-AIR TEMPERATURE 0.004 THD+N – Total Harmonic Distortion + Noise – % 107 106 Dynamic Range and SNR – dB 105 104 103 102 101 100 99 98 0.001 −40 97 −40 SNR Dynamic Range DYNAMIC RANGE AND SNR vs FREE-AIR TEMPERATURE 0.003 0.002 −15 10 35 60 85 G009 −15 10 35 60 85 G010 TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C Figure 9. TOTAL HARMONIC DISTORTION + NOISE vs SUPPLY VOLTAGE 0.004 THD+N – Total Harmonic Distortion + Noise – % 107 106 Dynamic Range and SNR – dB 105 104 103 102 101 100 99 98 0.001 4.5 97 4.5 Figure 10. DYNAMIC RANGE AND SNR vs SUPPLY VOLTAGE 0.003 Dynamic Range SNR 0.002 4.7 4.9 5.1 5.3 5.5 G011 4.7 4.9 5.1 5.3 5.5 G012 VCC – Supply Voltage – V VCC – Supply Voltage – V Figure 11. Figure 12. Submit Documentation Feedback 11 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com TYPICAL PERFORMANCE CURVES AT PGA GAIN = –5.5 dB (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted). TOTAL HARMONIC DISTORTION + NOISE vs fSAMPLE CONDITION 0.004 THD+N – Total Harmonic Distortion + Noise – % 107 106 Dynamic Range and SNR – dB 105 104 103 102 101 100 99 98 0.001 16 36 56 76 96 G013 DYNAMIC RANGE AND SNR vs fSAMPLE CONDITION 0.003 Dynamic Range SNR 0.002 97 16 36 56 76 96 G014 fSAMPLE Condition – kHz fSAMPLE Condition – kHz Figure 13. Figure 14. OUTPUT SPECTRUM AMPLITUDE vs FREQUENCY 0 Input Level = –60 dB Data Points = 8192 −20 −40 Amplitude – dB −60 −80 −100 −120 −140 0 5 10 f – Frequency – kHz G015 AMPLITUDE vs FREQUENCY 0 Input Level = –0.5 dB Data Points = 8192 −20 −40 Amplitude – dB 15 20 −60 −80 −100 −120 −140 0 5 10 f – Frequency – kHz G016 15 20 Figure 15. Figure 16. 12 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 TYPICAL PERFORMANCE CURVES AT PGA GAIN = –5.5 dB (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 48 kHz, system clock = 256 fS, 24-bit data (unless otherwise noted). TOTAL HARMONIC DISTORTION + NOISE vs SIGNAL LEVEL 100 THD+N – Total Harmonic Distortion + Noise – % 10 1 0.1 0.01 0.001 −100 −90 −80 −70 −60 −50 −40 −30 −20 −10 Signal Level – dB 0 G017 Figure 17. SUPPLY CURRENT SUPPLY CURRENT vs fSAMPLE CONDITION 30 ICC ICC and IDD – Supply Current – mA 25 PGA GAIN LINEARITY OVERALL GAIN vs GAIN SETTING 11 9 7 5 Overall Gain – dB 20 3 1 −1 −3 −5 15 IDD 10 5 −7 −9 0 16 36 56 76 96 G018 −11 −11 −9 −7 −5 −3 −1 1 3 5 7 9 11 G019 fSAMPLE Condition – kHz Gain Setting – dB Figure 18. Figure 19. Submit Documentation Feedback 13 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com DETAILED DESCRIPTION SYSTEM CLOCK The PCM1850A/1851A supports 256 fS, 384 fS, 512 fS, and 768 fS as the system clock, where fS is the audio sampling frequency. The system clock must be supplied on SCKI (pin 7). The PCM1850A/1851A has a system clock detection circuit which automatically senses if the system clock is operating at 256 fS, 384 fS, 512 fS, or 768 fS in slave mode. In master mode, the system clock frequency must be selected by mode control via the serial port. The 768-fS system clock is not available in master mode or for fS = 88.2 kHz and 96 kHz in the slave mode. The system clock is divided into 128 fS and 64 fS automatically, and these frequencies are used to operate the digital filter and the delta-sigma modulator, respectively. Table 1 shows the relationship of typical sampling frequency to system clock frequency, and Figure 20 shows system clock timing. Table 1. Sampling Frequency and System Clock Frequency SAMPLING RATE FREQUENCY (kHz) 32 44.1 48 64 88.2 96 (1) Slave mode only t(SCKH) H SCKI L t(SCKL) T0005-11 SYSTEM CLOCK FREQUENCY (MHz) 256 fS 8.192 11.2896 12.288 16.384 22.5792 24.576 384 fS 12.288 16.9344 18.432 24.576 33.8688 36.864 512 fS 16.384 22.5792 24.576 32.768 45.1584 49.152 768 fS (1) 24.576 33.8688 36.864 49.152 — — 2V 0.8 V SYMBOL t(SCKH) t(SCKL) System clock pulse duration, HIGH System clock pulse duration, LOW PARAMETER MIN 8 8 MAX UNIT ns ns Figure 20. System Clock Timing 14 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 POWER-ON-RESET SEQUENCE The PCM1850A/1851A has an internal power-on-reset circuit, and initialization (reset) is performed automatically at the time that the power supply (VDD) exceeds 2.2 V (typical). While VDD < 2.2 V (typical) and for 1024 system clocks after VDD > 2.2 V (typical), the PCM1850A/1851A stays in the reset state and the digital output is forced to zero. The digital output is valid after the reset state is released and the time of 4500/fS has passed. At the moment of the power-on-reset release, the PCM1850A/1851A does not need a system clock. Figure 21 illustrates the internal power-on-reset timing and the digital output for power-on reset. 2.6 V 2.2 V 1.8 V VDD Reset Internal Reset Release From Reset 1024 System Clocks System Clock 4500/fS DOUT Zero Data Normal Data T0014-10 Figure 21. Internal Power-On-Reset Timing Submit Documentation Feedback 15 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com ANALOG FRONT END The PCM1850A/1851A has a built-in analog front-end circuit, which is shown in the block diagram of Figure 22. Selection of the multiplexer input and PGA gain is controlled by mode control via the serial port as shown in Table 2 and Table 3. The change of the input selection and the gain selection is performed immediately after the serial control packet for the change is sent. A popping noise or other unexpected transient response could be generated in the audio signal during channel and gain change. Because the PCM1850A/1851A has no zero-cross detection and no other buffering capability for channel and gain change, appropriate data handling in the digital domain is recommended to control transients. The PCM1850A/1851A analog front end permits only ac input via an input capacitor; dc input is prohibited. A signal source resistance of less than 1 kΩ is recommended for the VINxx pins. All unselected channel inputs are terminated VREFS (= 0.5 VCC) using a resistor, typically 57 kΩ. The PCM1850A/1851A employs MOUTL/R pins (pins 12 and 11) to monitor the multiplexer output. The load on these pins must be ac-coupled and not less than 10 kΩ. The full-scale output level is typically 0.6 VCC. VINL1 VINL2 R R R PGA (11 dB to –11 dB) with MUX R G = –1 LIN+ VINL6 R LIN– VREFS (= 0.5 VCC) VREF1 (= 0.5 VCC) MOUTL B0131−01 Figure 22. Analog Front-End Block Diagram (L-Channel) Table 2. Multiplexer Input Selection CH2 0 0 0 0 1 1 1 1 CH1 0 0 1 1 0 0 1 1 CH0 0 1 0 1 0 1 0 1 CHANNEL Mute Channel 1 (default) Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Mute 16 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 Table 3. PGA Gain Selection PG5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 (1) PG4 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 PG3 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 PG2 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 PG1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 PG0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 PGA GAIN [dB] –11 (default) –10.5 –10 –9.5 –9 –8.5 –8 –7.5 –7 –6.5 –6 –5.5 –5 –4.5 –4 –3.5 –3 –2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 RIN [kΩ, Typical] (1) 201 199 196 193 190 188 185 181 178 175 172 169 165 162 158 155 151 147 144 140 136 133 129 125 122 118 114 111 107 103 100 96 93 89 86 83 80 77 73 70 68 65 62 59 57 RIN(kΩ, typical) = 258/(1 + 10GAIN/20) The PCM1850A/1851A becomes mute for PG[5:0] values other than those listed. Submit Documentation Feedback 17 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com SERIAL AUDIO DATA INTERFACE The PCM1850A/1851A interfaces with the audio system through BCK (pin 2), LRCK (pin 1), and DOUT (pin 3). Interface Mode The PCM1850A/1851A supports both master and slave modes as interface modes, and they are selected by mode control via the serial port as shown in Table 4. In master mode, the PCM1850A/1851A provides the timing for serial audio data communications between the PCM1850A/1851A and the digital audio processor or external circuit. While in slave mode, the PCM1850A/1851A receives the timing for data transfer from an external controller. Table 4. Interface Mode MD1 0 0 1 1 MD0 0 1 0 1 Master mode (256 fS) Master mode (384 fS) Master mode (512 fS) INTERFACE MODE Slave mode (256 fS, 384 fS, 512 fS, 768 fS) (default) Master Mode In master mode, BCK and LRCK work as output pins, and these pins are controlled by timing which is generated in the clock and timing control circuit of the PCM1850A/1851A. The frequency of BCK is fixed at 64 × LRCK. A 768-fS system clock is not available in master mode. Slave Mode In slave mode, BCK and LRCK work as input pins. The PCM1850A/1851A accepts the 64 BCK/LRCK or 48 BCK/LRCK (only for 384 fS SCKI) format. A 768-fS system clock is not available for fS = 88.2 kHz and 96 kHz in slave mode. Data Format The PCM1850A/1851A supports four audio data formats in both master and slave modes, and they are selected by mode control via the serial port as shown in Table 5. Figure 23 illustrates the data formats in both slave and master modes. Table 5. Data Format FORMAT NO. 0 1 2 3 FMT2 1 1 0 0 FMT1 0 0 0 1 FMT0 1 0 0 1 FORMAT Left-justified, 24-bit I2S, 24-bit, (default) Right-justified, 24-bit Right-justified, 16-bit 18 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 FORMAT 0: FMT[2:0] = 101b 24-Bit, MSB-First, Left-Justified LRCK BCK DOUT 1 2 3 22 23 24 LSB 1 2 3 22 23 24 LSB 1 Left-Channel Right-Channel MSB MSB FORMAT 1: FMT[2:0] = 100b 24-Bit, MSB-First, I2S LRCK BCK DOUT 1 2 3 22 23 24 LSB 1 2 3 22 23 24 LSB Left-Channel Right-Channel MSB MSB FORMAT 2: FMT[2:0] = 000b 24-Bit, MSB-First, Right-Justified LRCK BCK DOUT 24 1 2 3 22 23 24 LSB 1 2 3 22 23 24 LSB Left-Channel Right-Channel MSB MSB FORMAT 3: FMT[2:0] = 011b 16-Bit, MSB-First, Right-Justified LRCK BCK DOUT 16 1 2 3 14 15 16 LSB 1 2 3 14 15 16 LSB T0016-16 Left-Channel Right-Channel MSB MSB Figure 23. Audio Data Format (LRCK, BCK Work as Inputs in Slave Mode and Outputs in Master Mode) Submit Documentation Feedback 19 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com Interface Timing Figure 24 and Figure 25 illustrate the interface timing in slave and master modes, respectively. t(LRCP) LRCK t(BCKL) t(BCKH) t(LRSU) t(LRHD) 1.4 V t(BCKP) t(CKDO) t(LRDO) 1.4 V BCK DOUT 0.5 VDD T0017-02 SYMBOL t(BCKP) t(BCKH) t(BCKL) t(LRSU) t(LRHD) t(LRCP) t(CKDO) t(LRDO) tr tf BCK period BCK pulse duration, HIGH BCK pulse duration, LOW PARAMETER MIN 150 60 60 20 20 10 –10 –10 TYP MAX UNIT ns ns ns ns ns µs LRCK setup time to BCK rising edge LRCK hold time to BCK rising edge LRCK period Delay time, BCK falling edge to DOUT valid Delay time, LRCK edge to DOUT valid Rise time of all signals Fall time of all signals 20 20 10 10 ns ns ns ns NOTE: Timing measurement reference level is 1.4 V for input and 0.5 VDD for output. Rise and fall times are measured from 10% to 90% of IN/OUT signal swing. Load capacitance of DOUT is 20 pF. Figure 24. Audio Data Interface Timing (Slave Mode: LRCK, BCK Work as Inputs) 20 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 t(LRCP) LRCK t(BCKL) t(BCKH) t(CKLR) 0.5 VDD t(BCKP) t(CKDO) t(LRDO) 0.5 VDD BCK DOUT 0.5 VDD T0018-02 SYMBOL t(BCKP) t(BCKH) t(BCKL) t(CKLR) t(LRCP) t(CKDO) t(LRDO) tr tf BCK period BCK pulse duration, HIGH BCK pulse duration, LOW PARAMETER MIN 150 60 60 –10 10 –10 –10 TYP 1/(64 fS) 0.5 t(BCKP) 0.5 t(BCKP) 1/fS MAX 1000 400 400 20 60 20 20 10 10 UNIT ns ns ns ns µs ns ns ns ns Delay time, BCK falling edge to LRCK valid LRCK period Delay time, BCK falling edge to DOUT valid Delay time, LRCK edge to DOUT valid Rise time of all signals Fall time of all signals NOTE: Timing measurement reference level is 0.5 VDD. Rise and fall times are measured from 10% to 90% of IN/OUT signal swing. Load capacitance of all signals is 20 pF. Figure 25. Audio Data Interface Timing (Master Mode: LRCK, BCK Work as Outputs) Submit Documentation Feedback 21 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com SYNCHRONIZATION WITH DIGITAL AUDIO SYSTEM In slave mode, the PCM1850A/1851A operates under LRCK, synchronized with system clock SCKI. The PCM1850A/1851A does not need a specific phase relationship between LRCK and SCKI, but does require the synchronization of LRCK and SCKI. If the relationship between LRCK and SCKI changes more than ±6 BCKs for 64 BCKs/frame (±5 BCKs for 48 BCKs/frame) during one sample period due to LRCK or SCKI jitter, internal operation of the ADC halts within 1/fS and digital output is forced into the BPZ code until resynchronization between LRCK and SCKI is completed. In the case of changes less than ±5 BCKs for 64 BCKs/frame (±4 BCKs for 48 BCKs/frame), resynchronization with simultaneous discontinuity in the digital output does not occur. Figure 26 illustrates the digital output response for loss of synchronization and resynchronization. During undefined data, the PCM1850A/1851A might generate some noise in the audio signal. Also, the transition of normal to undefined data and undefined or zero data to normal creates a discontinuity of data in the digital output, which could generate some noise in the audio signal. It is recommended to set RST (pin 10) to LOW to get stable analog performance when the sampling rate, interface mode, or data format is changed. Synchronization Lost Resynchronization State of Synchronization SYNCHRONOUS ASYNCHRONOUS SYNCHRONOUS 1/fS DOUT NORMAL DATA UNDEFINED DATA 32/fS ZERO DATA NORMAL DATA T0020-05 Figure 26. ADC Digital Output for Loss of Synchronization and Resynchronization Power-Down Control RST (pin 10) controls the entire ADC operation. During reset mode, the supply current of the analog section is shut off and the digital section is initialized. DOUT (pin 3) is also disabled. Halting SCKI, BCK, and LRCK is recommended to minimize power dissipation. RST LOW HIGH POWER-DOWN MODE Reset and power-down modes Normal operation mode Overflow Flag Output The PCM1850A/1851A has an output flag (pin 4) that indicates when overflow occurs in the L-channel or R-channel, and this flag remains HIGH at least during the 8192/fS time for a momentary overflow occurrence. HPF Bypass Control The built-in HPF function for dc component rejection can be bypassed via the serial port. In bypass mode, the dc component of the analog input signal, the internal dc offset, etc., are converted and included in the digital output data. BYP 0 1 HPF (HIGH-PASS FILTER) MODE Normal (no dc component on DOUT) mode (default) Bypass (dc component on DOUT) mode 22 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 System Reset Control The system reset control is used to resynchronize the system via the serial port when the system clock frequency, interface mode, and data format are changed. Change them while SRST = LOW. If they are changed during normal operation, analog performance can be degraded. SRST 0 1 SYSTEM RESET Resynchronization Normal operation (default) Mode Register Reset Control The MRST bit is used to reset the mode control register to its default settings via the serial port. MRST 0 1 MODE REGISTER RESET Set default value Normal operation (default) SPI SERIAL CONTROL PORT FOR MODE CONTROL (PCM1850A) The user-programmable built-in functions of the PCM1850A can be controlled through a serial control port with the SPI format. All operations for the serial control port use 16-bit data words. Figure 27 shows the control data word format. The most-significant bit must be set to 0. Seven bits, labeled IDX[6:0], set the register index (or address) for write operations. The least-significant eight bits, D[7:0], contain the data to be written to the register specified by IDX[6:0]. Figure 28 shows the functional timing diagram for writing to the serial control port. MS (pin 30) is held at a logic-1 state until a register needs to be written. To start the register write cycle, MS is set to logic-0. Sixteen clocks are then provided on MC (pin 31), corresponding to the 16 bits of the control data word on MD (pin 32). After the sixteenth clock cycle has completed, the data is latched into the indexed mode control register in the write operation. To write the next data word, MS must be set to 1 once. MSB 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5 D4 D3 D2 D1 LSB D0 Register Index (or Address) Register Data R0001-01 Figure 27. Control Data Word Format for MD MS MC MD X 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5 D4 D3 D2 D1 D0 X X 0 IDX6 T0048-04 Figure 28. Serial Control Format Submit Documentation Feedback 23 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com CONTROL INTERFACE TIMING REQUIREMENTS (PCM1850A) Figure 29 shows a detailed timing diagram for the serial control interface of the PCM1850A. These timing parameters are critical for proper control port operation. t(MHH) MS t(MSS) t(MCH) MC t(MCY) MD t(MDS) t(MDH) T0013-06 1.4 V t(MCL) t(MSH) 1.4 V LSB 1.4 V SYMBOL t(MCY) t(MCL) t(MCH) t(MHH) t(MSS) t(MSH) t(MDH) t(MDS) (1) MC pulse cycle time MC LOW-level time MC HIGH-level time MS HIGH-level time MS falling edge to MC rising edge MS hold time (1) MD hold time MD setup time PARAMETER MIN 100 40 40 80 15 15 15 15 MAX UNIT ns ns ns ns ns ns ns ns MC rising edge for LSB to MS rising edge Figure 29. PCM1850A Control Interface Timing I2C SERIAL CONTROL PORT FOR MODE CONTROL (PCM1851A) The user-programmable built-in function of the PCM1851A can be controlled through the I2C-format serial control port, SDA (pin 32) and SCL (pin 31). The PCM1851A supports the I2C serial bus and the data transmission protocol for standard mode as a slave device. This protocol is explained in I2C specification 2.0. Slave Address MSB 1 0 0 1 0 1 ADR LSB R/nW The PCM1851A has 7 bits for its own slave address. The first six bits (MSBs) of the slave address are factory preset to 100101. The last bit of the address byte is the device select bit, which can be user-defined by the ADR pin (pin 30). A maximum of two PCM1851As can be connected on the same bus at one time. Each PCM1851A responds when it receives its own slave address. Packet Protocol A master device must control packet protocol, which consists of start condition, slave address with read/write bit, data if write or acknowledgement if read, and stop condition. The PCM1851A supports only slave receivers, so the R/W bit must be set to 0. 24 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 SDA SCL St 1−7 Slave Address 8 R/W 9 ACK 1−8 DATA 9 ACK 1−8 DATA 9 ACK 9 ACK Sp Start Condition R/W: Read Operation if 1; Otherwise, Write Operation ACK: Acknowledgement of a Byte if 0 DATA: 8 Bits (Byte) M St M Slave Address M R/W S ACK M DATA S ACK M DATA S ACK S ACK Stop Condition Transmitter Data Type M Sp M: Master Device St: Start Condition S: Slave Device Sp: Stop Condition T0049-05 Figure 30. Basic I C Framework Write Operation The PCM1851A has only the write mode. A master can write to any PCM1851A registers using single or multiple accesses. The master sends a PCM1851A slave address with a write bit, a register address, and the data. If multiple access is required, the address is that of the starting register, followed by the data to be transferred. When the data are received properly, the index register is incremented by 1 automatically. When the index register reaches 33h, the next value is 31h. When undefined registers are accessed, the PCM1851A does not send an acknowledgement. Figure 31 is a diagram of the write operation. The register address and the write data are 8 bits and MSB-first format. Transmitter Data Type 2 M St M Slave Address M W S ACK M Reg Address S ACK M Write Data 1 S ACK M Write Data 2 S ACK S ACK M Sp M: Master Device S: Slave Device St: Start Condition ACK: Acknowledge W: Write Sp: Stop Condition R0002-03 Figure 31. Framework for Write Operation Submit Documentation Feedback 25 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com TIMING DIAGRAM Start t(D-HD) t(BUF) t(D-SU) t(SDA-R) Repeated Start t(SDA-F) t(P-SU) Stop SDA t(SCL-R) t(LOW) SCL t(RS-HD) t(S-HD) t(SCL-F) t(HI) t(RS-SU) T0050-01 SYMBOL f(SCL) t(BUF) t(LOW) t(HI) t(RS-SU) t(S-HD), t(RS-HD) t(D-SU) t(D-HD) t(SCL-R) t(SCL-F) t(SDA-R) t(SDA-F) t(P-SU) CB VNH SCL clock frequency PARAMETER Bus free time between STOP and START conditions Low period of the SCL clock High period of the SCL clock Setup time for START/repeated START condition Hold time for START/repeated START condition Data setup time Data hold time Rise time of SCL signal Fall time of SCL signal Rise time of SDA signal Fall time of SDA signal Setup time for STOP condition Capacitive load for SDA and SCL lines Noise margin at HIGH level for each connected device (including hysteresis) MIN 4.7 4.7 4 4.7 4 250 0 20 + 0.1 CB 20 + 0.1 CB 20 + 0.1 CB 20 + 0.1 CB 4 MAX 100 UNIT kHz µs µs µs µs µs ns 900 1000 1000 1000 1000 400 ns ns ns ns ns µs pF V 0.2 VDD Figure 32. PCM1851A Control Interface Timing Requirements 26 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 MODE CONTROL REGISTERS User-Programmable Mode Control Functions The PCM1850A/1851A has several user-programmable functions which are accessed via control registers. The registers are programmed using the serial control port which is discussed in the SPI Serial Control Port for Mode Control (PCM1850A) and I 2C Serial Control Port for Mode Control (PCM1851A) sections of this data sheet. Table 6 lists the available mode control functions, along with their reset default conditions and associated register index. Register Map The mode control register map is shown in Table 7. Each register includes an index (or address) indicated by the IDX[6:0] bits B[14:8]. Table 6. User-Programmable Mode Control Functions FUNCTION Mode register reset PGA gain control Multiplexer input channel control HPF bypass control System reset Audio interface mode control Audio interface format control RESET DEFAULT Normal operation –11 dB Channel 1 HPF enable Normal operation Slave I2S REGISTER 31 31 32 33 33 33 33 BIT(S) MRST PG[5:0] CH[2:0] BYP SRST MD[1:0] FMT[2:0] Table 7. Mode Control Register Map HEX Register 31 Register 32 Register 33 (1) B15 0 0 0 B14 0 0 0 B13 1 1 1 B12 1 1 1 B11 0 0 0 B10 0 0 0 B9 0 1 1 B8 1 0 1 B7 B6 B5 PG5 B4 PG4 MD1 B3 PG3 MD0 B2 PG2 CH2 FMT2 B1 PG1 CH1 FMT1 B0 PG0 CH0 FMT0 RSV (1) MRST BYP RSV (1) RSV (1) RSV (1) RSV (1) RSV (1) SRST RSV (1) RSV bits must be always written as 0. No values can be written in address 30h. Submit Documentation Feedback 27 PCM1850A PCM1851A SLES173 – MARCH 2006 www.ti.com APPLICATION INFORMATION TYPICAL CIRCUIT CONNECTION DIAGRAM The following figure illustrates a typical circuit connection diagram for six stereo inputs and an analog monitor. Analog Input/Output C17 C16 C15 C14 C13 C12 C11 C10 + 24 VINR6 + 23 VINL6 + 22 VINR5 + 21 VINL5 + 20 VINR4 + 19 VINL4 + 18 VINR3 + 17 VINL3 + C5 C4 C3 +5 V 0V + C1 + + 25 VREFS 26 VREF1 27 VREF2 28 Vcc PCM1850A/1851A 29 AGND 30 MS (ADR)(1) 31 MC (SCL)(1) DGND TEST0 32 MD (SDA)(1) OVER DOUT LRCK BCK VINR2 16 VINL2 15 VINR1 14 VINL1 13 MOUTL 12 MOUTR 11 RST 10 TEST1 9 + + + + + + C9 C8 C7 C6 C19 C18 Control 1 2 3 4 5 C2 VDD 6 SCKI 7 8 + 3.3 V (1) Audio Data Processor PCM1850A (PCM1851A) S0181-01 NOTE: C1, C2: 0.1-µF ceramic and 10-µF electrolytic capacitors are recommended, depending on layout and power supply. C3, C4, C5: 0.1-µF ceramic and 10-µF electrolytic capacitors are recommended. C6–C17: A 0.33-µF capacitor gives a 2.9-Hz (τ = 0.33 µF × 169 kΩ) typical cutoff frequency at the HPF input in normal operation, and it requires power-on settling time with a 56-ms time constant in the power-on initialization period. Cutoff frequency and time constant depend on PGA gain. Cutoff frequency varies from 2.4 Hz to 8.5 Hz for 0.33 µF. DC-coupled input is inhibited for the analog input, VINL[1:6] and VINR[1:6]. C18–C19: A 2.2-µF capacitor with a 10-kΩ load gives a 7.2-Hz cutoff frequency. 28 Submit Documentation Feedback www.ti.com PCM1850A PCM1851A SLES173 – MARCH 2006 APPLICATION INFORMATION (continued) BOARD DESIGN AND LAYOUT CONSIDERATIONS VCC, VDD Pins The digital and analog power supply lines to the PCM1850A/1851A must be bypassed to the corresponding ground pins with 0.1-µF ceramic and 10-µF electrolytic capacitors as close to the pins as possible to maximize the dynamic performance of the ADC. AGND, DGND Pins To maximize the dynamic performance of the PCM1850A/1851A, the analog and digital grounds are not connected internally. These grounds must have low impedance to avoid digital noise feeding back into the analog ground. Therefore, they should be connected directly to each other under the parts to reduce the potential of a noise problem. VINL[1:6], VINR[1:6] Pins A 0.33-µF capacitor is recommended as the ac-coupling capacitor, which gives a 2.4- to 8.5-Hz cutoff frequency. If higher full-scale input voltage is required, it can be adjusted by adding only one series resistor to each VINxx pin, but a signal source resistance less than 1 kΩ is recommended for these pins in order to keep accuracy of the gain control command and to maintain crosstalk performance. MOUTL, MOUTR Pins An ac-coupled light load is recommended; a 2.2-µF capacitor with a 10-kΩ load gives a 7.2-Hz cutoff frequency. VREF1, VREF2, VREFS Pins Between VREF1 and AGND, VREF2 and AGND, and VREFS and AGND, 0.1-µF ceramic and 10-µF electrolytic capacitors are recommended to ensure low source impedance of the ADC references. These capacitors should be located as close as possible to the VREF1, VREF2, and VREFS pins to reduce dynamic errors on the ADC references. The differential voltage between VREF2 and AGND sets the analog input full-scale range. BCK and LRCK Pins (in Master Mode), DOUT Pin These pins have enough load-driving capability. However, if the output line is long, locating a buffer near the PCM1850A/1851A and minimizing load capacitance is recommended in order to minimize the digital-analog crosstalk and maximize the dynamic performance of the ADC. System Clock Because the PCM1850A/1851A operates based on a system clock, the quality of the system clock can influence dynamic performance. Therefore, it is recommended to consider the system clock duty, jitter, and the time difference between the system clock transition and the BCK or LRCK transition in slave mode. Submit Documentation Feedback 29 PACKAGE OPTION ADDENDUM www.ti.com 16-Mar-2007 PACKAGING INFORMATION Orderable Device PCM1850APJT PCM1850APJTG4 PCM1850APJTR PCM1850APJTRG4 PCM1851APJT PCM1851APJTG4 PCM1851APJTR PCM1851APJTRG4 (1) Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP Package Drawing PJT PJT PJT PJT PJT PJT PJT PJT Pins Package Eco Plan (2) Qty 32 32 32 32 32 32 32 32 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) 1000 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) 1000 Green (RoHS & no Sb/Br) 1000 Green (RoHS & no Sb/Br) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MPQF112 – NOVEMBER 2001 PJT (S-PQFP–N32) PLASTIC QUAD FLATPACK 0,80 0,45 0,30 0,20 M 0,20 0,09 32 0,15 0,05 7,00 SQ 9,00 SQ 0,75 0,45 0,25 Gage Plane 1 0°– 7° 1,05 0,95 Seating Plane 1,20 1,00 0,10 4203540/A 11/01 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers RFID Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated