RC4559D

   

 
  
SLOS074 − D2785, OCTOBER 1983 — REVISED JUNE 1988 • • • • • D OR P PACKAGE (TOP VIEW) Unity-Gain Bandwidth . . . 3 MHz Min Slew Rate . . . 1.5 V/ns Min AMP # 1 Low Equivalent Input Noise Voltage 2 µV/Hz Max (20 Hz to 20 kHz) OUT IN − IN + VCC − 1 8 2 7 3 6 4 5 VCC + OUT IN − IN + AMP # 2 No Frequency Compensation Required No Latch Up symbol (each amplifier) Wide Common-Mode Voltage Range Low Power Consumption IN+ Designed to be Interchangeable with Raytheon RC4559 IN− − • • • Matched Gain and Offset Between Amplifiers + • OUT AVAILABLE OPTIONS SYMBOLIZATION DEVICE PACKAGE SUFFIX RC4559 D, P OPERATING TEMPERATURE RANGE VIO max at 25°C −0°C to 70°C 6 mV The D packages are available taped and reeled. Add the suffix R to the device type when ordering. (i.e.,RC4559DR) description The RC4559 is a dual high-performance operational amplifier. The high common-mode input voltage and the absence of latch-up make this amplifier ideal for low-noise signal applications such as audio preamplifiers and signal conditioners. This amplifier features a guaranteed dynamic performance and output drive capability that far exceeds that of the general-purpose type amplifiers. The RC4559 is characterized for operation from 0°C to 70°C. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage VCC+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Supply voltage VCC − (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −18 V Differential input voltage (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 30 V Input voltage (any input, see Notes 1 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 15 V Duration of output short-circuit to ground, one amplifier at a time (see Note 4) . . . . . . . . . . . . . . . . . unlimited Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 mW Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 125°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C NOTES: 1. All voltage values, unless otherwise noted, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC−. 2. Differential voltages are at the noninverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. Copyright  1991, Texas Instruments Incorporated POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 
   

 
  
electrical characteristics at specified free-air temperature, VCC+ = 15 V, VCC− = −15 V TA‡ 25°C TEST CONDITIONS† PARAMETER VIO Input offset voltage VO = 0 Full Range IIO Input offset current VO = 0 Full range IIBI nput bias current VO = 0 VI Input voltage range MAX 2 6 5 40 Full range 250 500 25°C ± 12 ± 13 25°C ± 12 ± 13 ± 10 UNIT mV 100 200 25°C RL = 600 Ω Maximum peak output voltlage swing TYP 7.5 25°C RL ≥ 3 kΩ VOM MIN nA nA V 25°C ± 9.5 RL ≥ 2 kΩ Full range ± 10 25°C 20 Full range 15 25°C 24 32 kHz V VI Input voltage range VO = ± 10 V, RL = 2 kΩ BOM Maximum output-swing bandwidth VOPP = 20 V, RL = 2 kΩ B1 ri Unity-gain bandwidth 25°C 3 4 MHz Input resistance 25°C 0.3 1 MΩ CMRR Common-mode rejection ratio 25°C 80 100 dB kSVS Supply voltage sensitivity (∆VIO/∆VCC) VO = 0 VO = 0 Vn Equivalent input noise voltage (closed loop) AVD = 100, RS = 1 kΩ, f = 20 Hz to 20 kHz In Equivalent input noise current f = 20 Hz to 20 kHz ICC Vo1/Vo2 Supply current (both amplifiers) No load, No signal AVD = 100, RS = 1 kΩ, f = 10 kHz Crosstalk attentuation 300 V/mV 25°C 10 75 µV/V 25°C 1.4 2 µV 25°C 25 25°C 3.3 5.6 pA 0°C 4 6.6 70°C 3 5 25°C 90 mA dB † All characteristics are specified under open-loop operation, unless otherwise noted. ‡ Full range operating free-air temperature range is 0°C to 70°C. matching characteristics at VCC+ = 15 V, VCC− = −15 V, TA = 25°C PARAMETER VIO IIO Input offset voltage IIB AVD Input bias current TEST CONDITIONS Input offset current Large-signal differential voltage amplification MIN TYP MAX UNIT VO = 0 VO = 0 ± 0.2 mV ± 7.5 nA VO = 0 VO = ± 10 V, RL = 2 kΩ ± 15 nA ±1 dB operating characteristics, VCC+ = 15 V, VCC− = −15 V, TA = 25°C PARAMETER tr Rise time SR Slew rate at unity gain TEST CONDITIONS VI = 20 mV, RL = 2 kΩ, CL = 100 pF VI = 10 mV, RL = 2 kΩ, CL = 100 pF MIN 80 Overshoot 2 TYP MAX UNIT µs 18% POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1.5 2 V/µs PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) RC4559D ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 RC4559 RC4559DR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 RC4559 RC4559P ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 RC4559P RC4559PE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 RC4559P (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of