SN74ABT5403DW

SN54ABT5403, SN74ABT5403 12-BIT LINE/MEMORY DRIVERS WITH 3-STATE OUTPUTS SCBS236B – JUNE 1992 – REVISED JANUARY 1997 D D D D D D SN54ABT5403 . . . JT PACKAGE SN74ABT5403 . . . DW PACKAGE (TOP VIEW) Output Ports Have Equivalent 25-Ω Series Resistors, So No External Resistors Are Required State-of-the-Art EPIC-ΙΙB  BiCMOS Design Significantly Reduces Power Dissipation Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C Typical VOLV (Output Undershoot) < 0.5 V at VCC = 5 V, TA = 25°C Package Options Include Plastic Small-Outline (DW) Package, Ceramic Chip Carriers (FK), and DIPs (JT) Y1 Y2 Y3 Y4 Y5 Y6 GND Y7 Y8 Y9 Y10 Y11 Y12 OE1 description These 12-bit buffers and line drivers are designed specifically to improve both the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 D1 D2 D3 D4 D5 D6 D7 VCC D8 D9 D10 D11 D12 OE2 D4 D5 D6 D7 VCC D8 D9 SN54ABT5403 . . . FK PACKAGE (TOP VIEW) The 3-state control gate is a 2-input AND gate with active-low inputs so that if either output-enable (OE1 or OE2) input is high, all 12 outputs are in the high-impedance state. These devices provide inverted data. 4 D3 D2 D1 Y1 Y2 Y3 Y4 The outputs, which are designed to source or sink up to 12 mA, include equivalent 25-Ω series resistors to reduce overshoot and undershoot. 3 2 1 28 27 26 25 6 24 7 23 8 22 9 21 10 20 11 19 12 13 14 15 16 17 18 D10 D11 D12 OE2 OE1 Y12 Y11 Y5 Y6 GND Y7 Y8 Y9 Y10 To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. 5 The SN54ABT5403 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT5403 is characterized for operation from –40°C to 85°C. FUNCTION TABLE INPUTS OE1 OE2 D OUTPUT Y L L L H L L H L H X X Z X H X Z Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC-ΙΙB is a trademark of Texas Instruments Incorporated. Copyright  1997, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ABT5403, SN74ABT5403 12-BIT LINE/MEMORY DRIVERS WITH 3-STATE OUTPUTS SCBS236B – JUNE 1992 – REVISED JANUARY 1997 logic symbol† 14 OE1 OE2 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 logic diagram (positive logic) & OE1 EN 15 28 27 1 OE2 1 2 26 3 25 4 24 5 23 6 22 8 20 9 19 10 18 11 17 12 16 13 D1 14 15 28 1 Y1 Y1 Y2 Y3 To 11 Other Channels Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the DW and JT packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡ Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Current into any output in the low state, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C ‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ABT5403, SN74ABT5403 12-BIT LINE/MEMORY DRIVERS WITH 3-STATE OUTPUTS SCBS236B – JUNE 1992 – REVISED JANUARY 1997 recommended operating conditions (see Note 3) SN54ABT5403 VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current ∆t/∆v Input transition rise or fall rate High-level input voltage SN74ABT5403 MIN MAX MIN MAX 4.5 5.5 4.5 5.5 2 2 0.8 Input voltage 0 Low-level output current Outputs enabled TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating. –55 0 V V 0.8 VCC –12 UNIT VCC –12 V V mA 12 12 mA 10 10 ns/V 85 °C 125 –40 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS SN54ABT5403 –1.2 –1.2 MIN MAX SN74ABT5403 MIN II = –18 mA IOH = –1 mA 3.35 3.7 3.3 3.35 VCC = 5 V, IOH = –1 mA IOH = –3 mA 3.85 4.2 3.8 3.85 3 3.1 IOH = –12 mA IOL = 8 mA 2.6 VCC = 4 4.5 5V Vhys II TA = 25°C TYP† MAX VCC = 4.5 V, VCC = 4.5 V, VCC = 4 4.5 5V VOL MIN MAX –1.2 UNIT V V 2.6 0.8 0.65 IOL = 12 mA 0.8 100 V mV ±1 ±1 ±1 µA VCC = 5.5 V, VCC = 5.5 V, VI = VCC or GND VO = 2.7 V VCC = 5.5 V, VCC = 0, VO = 0.5 V VI or VO ≤ 4.5 V ICEX VCC = 5.5 V, VO = 5.5 V Outputs high IO IOS‡ VCC = 5.5 V, VCC = 5.5 V, VO = 2.5 V VO = 0 VCC = 5.5 V, IO = 0, VI = VCC or GND Outputs high 5 50 50 50 µA ICC Outputs low 36 45 45 45 mA 1 50 50 50 µA 1.5 1.5 1.5 0.05 0.05 0.05 1.5 1.5 1.5 IOZH IOZL Ioff Data inputs ∆ICC§ Control inputs Ci Co Outputs disabled 50 50 µA –50 –50 µA ±100 µA 50 µA ±100 50 –25 –45 –50 VCC = 5.5 V, Outputs enabled One input at 3.4 V,, Other inputs at Outputs disabled VCC or GND VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V 50 –50 50 –100 –25 –100 –25 –100 mA –200 –50 –200 –50 –200 mA mA 3 pF 8 pF † All typical values are at VCC = 5 V. ‡ Not more than one output should be tested at a time, and the duration of the test should not exceed one second. § This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ABT5403, SN74ABT5403 12-BIT LINE/MEMORY DRIVERS WITH 3-STATE OUTPUTS SCBS236B – JUNE 1992 – REVISED JANUARY 1997 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tPLH tPHL D Y tPZH tPZL OE Y tPHZ tPLZ OE Y PARAMETER VCC = 5 V, TA = 25°C SN54ABT5403 MIN TYP MAX MIN MAX MIN MAX 2 4.5 6.1 2 7 2 6.9 1.5 4.4 5.2 1.5 5.9 1.5 5.7 2.5 5.7 6.6 2.5 8.6 2.5 8.5 2 4.4 5.5 2 6.9 2 6.8 1.5 3.6 4.4 1.5 5.5 1.5 5.2 1.5 4.2 5.4 1.5 7.4 1.5 6.9 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 SN74ABT5403 • DALLAS, TEXAS 75265 UNIT ns ns ns SN54ABT5403, SN74ABT5403 12-BIT LINE/MEMORY DRIVERS WITH 3-STATE OUTPUTS SCBS236B – JUNE 1992 – REVISED JANUARY 1997 PARAMETER MEASUREMENT INFORMATION 7V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V Input 1.5 V th 3V 1.5 V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V Input 0V 1.5 V 1.5 V VOL tPLH tPHL VOH Output 1.5 V 1.5 V VOL 1.5 V 0V tPLZ Output Waveform 1 S1 at 7 V (see Note B) VOH Output 1.5 V tPZL tPHL tPLH 3V Output Control 1.5 V Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V tPZH 3.5 V VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 n D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74ABT5403DWR ACTIVE SOIC DW 28 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ABT5403 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of