SN74ALB16245DLR

SN74ALB16245 3.3-V ALB 16-BIT TRANSCEIVER WITH 3-STATE OUTPUTS SCBS678C – SEPTEMBER 1996 – REVISED JANUARY 2001 D D D D D D DGG, DGV, OR DL PACKAGE (TOP VIEW) Member of Texas Instruments’ Widebus Family State-of-the-Art Advanced Low-Voltage BiCMOS (ALB) Technology Design for 3.3-V Operation Schottky Diodes on All Inputs to Eliminate Overshoot and Undershoot Industry Standard ’16245 Pinout Distributed VCC and GND Pins Minimize High-Speed Switching Noise Flow-Through Architecture Optimizes PCB Layout 1DIR 1B1 1B2 GND 1B3 1B4 VCC 1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCC 2B5 2B6 GND 2B7 2B8 2DIR description The SN74ALB16245 is a 16-bit transceiver designed for high-speed, low-voltage (3.3-V) VCC operation. This device is intended to replace the conventional transceiver in any speed-critical path. The small propagation delay is achieved using a unity-gain amplifier on the input and feedback resistors from input to output, which allows the output to track the input with a small offset voltage. This device can be used as two 8-bit transceivers or one 16-bit transceiver. It allows data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so that the buses are effectively isolated. 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 GND 1A7 1A8 2A1 2A2 GND 2A3 2A4 VCC 2A5 2A6 GND 2A7 2A8 2OE ORDERING INFORMATION TOP-SIDE MARKING Tube SN74ALB16245DL Tape and reel SN74ALB16245DLR TSSOP – DGG Tape and reel SN74ALB16245DGGR TVSOP – DGV Tape and reel SN74ALB16245DGVR SSOP – DL 40°C to 85°C –40°C ORDERABLE PART NUMBER PACKAGE† TA ALB16245 ALB16245 AV245 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright  2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74ALB16245 3.3-V ALB 16-BIT TRANSCEIVER WITH 3-STATE OUTPUTS SCBS678C – SEPTEMBER 1996 – REVISED JANUARY 2001 FUNCTION TABLE (each 8-bit section) INPUTS OE DIR OPERATION L L B data to A bus L H A data to B bus H X Isolation logic symbol† 48 1OE 1DIR 1 G3 3 EN1 [BA] 3 EN2 [AB] 25 2OE 2DIR 24 G6 6 EN4 [BA] 6 EN5 [AB] 1A1 47 2 1 1B1 2 1A2 1A3 1A4 1A5 1A6 1A7 1A8 2A1 2A2 2A3 2A4 2A5 2A6 2A7 2A8 46 3 44 5 43 6 41 8 40 9 38 11 37 12 36 13 4 35 5 33 16 32 17 30 19 29 20 27 22 26 23 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1B2 1B3 1B4 1B5 1B6 1B7 1B8 2B1 2B2 2B3 2B4 2B5 2B6 2B7 2B8 SN74ALB16245 3.3-V ALB 16-BIT TRANSCEIVER WITH 3-STATE OUTPUTS SCBS678C – SEPTEMBER 1996 – REVISED JANUARY 2001 logic diagram (positive logic) 1DIR 1 2DIR 48 1A1 25 1OE 47 2A1 2 24 2OE 36 13 1B1 To Seven Other Channels 2B1 To Seven Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI: Except I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V I/O ports (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through each VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This value is limited to 4.6 V maximum. 3. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions MIN MAX 3 3.6 V High-level output current –25 mA Low-level output current 25 mA 5 ns/V 85 °C VCC IOH‡ Supply voltage IOL‡ ∆t/∆v Input transition rise or fall rate Outputs enabled TA Operating free-air temperature ‡ See Figures 1 and 2 for typical I/O ranges. –40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT 3 SN74ALB16245 3.3-V ALB 16-BIT TRANSCEIVER WITH 3-STATE OUTPUTS SCBS678C – SEPTEMBER 1996 – REVISED JANUARY 2001 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK II TEST CONDITIONS A or B ports VCC = 3 V II = 18 mA II = –18 mA Control inputs VCC = 3.6 V, VI = VCC or GND VI = VCC A or B ports VCC = 3 3.6 6V VI = 0 MIN 3.7 –0.9 OE low MAX UNIT VCC+1.2 –1.2 V 0.4 OE high OE low –0.7 OE high IOZH IOZL VCC = 3.6 V, VCC = 3.6 V, VO = 3 V VO = 0.5 V ICC/buffer ICCZ VCC = 3.6 V, VCC = 3.6 V, IO = 0, VI = VCC or GND Control inputs = VCC or GND ∆ICC‡ VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 VO = 3 V or 0 Cio TYP† ±10 µA 0.6 mA 25 µA –1 mA –60 µA 0.7 20 µA –0.2 –50 µA 3.7 5.6 mA 0.8 mA 600 µA 3.5 pF 7.5 pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 3) FROM (INPUT) TO (OUTPUT) tpd A or B B or A 0.6 1.3 ten OE A or B 1.5 tdis OE A or B 1.8 † All typical values are at VCC = 3.3 V, TA = 25°C. 4 VCC = 3.3 V ± 0.3 V MIN TYP† MAX PARAMETER POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT 2 ns 3.2 6 ns 2.8 4.2 ns SN74ALB16245 3.3-V ALB 16-BIT TRANSCEIVER WITH 3-STATE OUTPUTS SCBS678C – SEPTEMBER 1996 – REVISED JANUARY 2001 OUTPUT VOLTAGE HIGH vs INPUT VOLTAGE VOH – Output Voltage – V 3.5 3 2.5 –100 µA –25 mA –6 mA 2 1.5 1.5 2 2.5 3 3.5 4 VI – Input Voltage – V Figure 1. VOH Over Recommended Free-Air Temperature Range OUTPUT VOLTAGE LOW vs INPUT VOLTAGE 2 VOL – Output Voltage – V 1.5 25 mA 1 100 µA 0.5 6 mA 0 0 0.5 1 1.5 2 VI – Input Voltage – V Figure 2. VOL Over Recommended Free-Air Temperature Range POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74ALB16245 3.3-V ALB 16-BIT TRANSCEIVER WITH 3-STATE OUTPUTS SCBS678C – SEPTEMBER 1996 – REVISED JANUARY 2001 PARAMETER MEASUREMENT INFORMATION 6V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND LOAD CIRCUIT tw 3V 3V Timing Input 0V 0V VOLTAGE WAVEFORMS PULSE DURATION th 3V Data Input 1.5 V 1.5 V 0V 1.5 V 1.5 V 0V tPZL 3V 1.5 V 3V Output Control (low-level enabling) VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 0V tPLH Output 1.5 V 1.5 V tsu Input 1.5 V Input Output Waveform 1 S1 at 6 V (see Note B) 3V 1.5 V VOL + 0.3 V tPZH tPHL VOH 1.5 V tPLZ 1.5 V VOL Output Waveform 2 S1 at GND (see Note B) VOL tPHZ 1.5 V VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 3. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74ALB16245DGGR ACTIVE TSSOP DGG 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ALB16245 SN74ALB16245DL ACTIVE SSOP DL 48 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ALB16245 SN74ALB16245DLR ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ALB16245 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of