SN74ALS35ADRG4


            
SDAS011C − DECEMBER 1983 − REVISED DECEMBER 1994 • • D OR N PACKAGE (TOP VIEW) Noninverter With Open-Collector Outputs Package Options Include Plastic Small-Outline (D) Packages and Standard Plastic (N) 300-mil DIPs 1A 1Y 2A 2Y 3A 3Y GND description The SN74ALS35A contains six independent noninverters with open-collector outputs. They perform the Boolean function Y = A. The open-collector outputs require pullup resistors to perform correctly. These outputs may be connected to other open-collector outputs to implement active-low wired-OR or active-high wired-AND functions. Open-collector devices are often used to generate higher VOH levels. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 6A 6Y 5A 5Y 4A 4Y The SN74ALS35A is characterized for operation from 0°C to 70°C. FUNCTION TABLE (each buffer) INPUT A OUTPUT Y H H L L logic symbol† 1A 2A 3A 4A 5A 6A logic diagram (positive logic) 1 2 3 4 5 6 9 8 11 10 13 12 1A 1Y 1 2 3 4 5 6 9 8 11 10 13 12 1Y 2Y 3Y 2A 2Y 4Y 5Y 3A 3Y 6Y 4A † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 5A 6A 4Y 5Y 6Y Copyright  1994, Texas Instruments Incorporated      ! "#$ !  %#&'" ($) (#"! "  !%$""! %$ *$ $!  $+! !#$! !(( ,-) (#" %"$!!. ($!  $"$!!'- "'#($ $!.  '' %$$!) • DALLAS, TEXAS 75265 • HOUSTON, TEXAS 77251−1443 POST OFFICE BOX 655303 POST OFFICE BOX 1443 1 

            
SDAS011C − DECEMBER 1983 − REVISED DECEMBER 1994 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions MIN NOM MAX 4.5 5 5.5 VCC VIH Supply voltage VIL VOH Low-level input voltage 0.8 High-level output voltage 5.5 IOL TA Low-level output current High-level input voltage 2 Operating free-air temperature UNIT V V 0 V V 8 mA 70 °C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK TEST CONDITIONS VCC = 4.5 V, VOL VCC = 4.5 V II IIH VCC = 5.5 V, VCC = 5.5 V, IIL IOH VCC = 5.5 V, VCC = 4.5 V, ICCH ICCL VCC = 5.5 V, VCC = 5.5 V, MIN TYP‡ II = −18 mA IOL = 4 mA IOL = 8 mA VI = 7 V MAX UNIT −1.2 V 0.25 0.4 0.35 0.5 VI = 2.7 V VI = 0.4 V V 0.1 mA 20 µA −0.1 mA 0.1 mA VOH = 5.5 V VI = 4.5 V 2.7 4.7 mA VI = 0 4.1 6.3 mA ‡ All typical values are at VCC = 5 V, TA = 25°C. switching characteristics (see Figure 1) PARAMETER tPLH tPHL FROM (INPUT) TO (OUTPUT) A Y VCC = 4.5 V to 5.5 V, CL = 50 pF, RL = 2 k Ω, TA = MIN to MAX§ MIN MAX 20 50 2 14 § For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. 2 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • UNIT ns 

            
SDAS011C − DECEMBER 1983 − REVISED DECEMBER 1994 PARAMETER MEASUREMENT INFORMATION SERIES 54ALS/74ALS AND 54AS/74AS DEVICES 7V RL = R1 = R2 VCC S1 RL R1 Test Point From Output Under Test CL (see Note A) From Output Under Test RL Test Point CL (see Note A) CL (see Note A) LOAD CIRCUIT FOR BI-STATE TOTEM-POLE OUTPUTS LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS 3.5 V Timing Input Test Point From Output Under Test LOAD CIRCUIT FOR 3-STATE OUTPUTS 3.5 V High-Level Pulse 1.3 V R2 1.3 V 1.3 V 0.3 V 0.3 V tsu Data Input tw th 3.5 V 1.3 V 3.5 V Low-Level Pulse 1.3 V 0.3 V 1.3 V 0.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATIONS 3.5 V Output Control (low-level enabling) 1.3 V 1.3 V 0.3 V tPZL Waveform 1 S1 Closed (see Note B) tPLZ 3.5 V Input tPHZ 1.3 V 0.3 V tPHL tPLH VOH In-Phase Output VOL 0.3 V 1.3 V 1.3 V VOL tPLH tPHL VOH 1.3 V 1.3 V [3.5 V 1.3 V tPZH Waveform 2 S1 Open (see Note B) 1.3 V VOH Out-of-Phase Output (see Note C) 0.3 V [0 V 1.3 V 1.3 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. When measuring propagation delay items of 3-state outputs, switch S1 is open. D. All input pulses have the following characteristics: PRR ≤ 1 MHz, tr = tf = 2 ns, duty cycle = 50%. E. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuits and Voltage Waveforms • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 3 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74ALS35AD ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS35A SN74ALS35AN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN74ALS35AN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of