SN74LVTH126PWRG4

 
      

 
 
SCBS746B − JULY 2000 - REVISED OCTOBER 2003 D Support Mixed-Mode Signal Operation (5-V D D D D D Input and Output Voltages With 3.3-V VCC) Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) VCC. 3. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 4) SN54LVTH126 SN74LVTH126 MIN MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 5.5 5.5 V IOH IOL High-level output current −24 −32 mA Low-level output current 48 64 mA ∆t/∆v Input transition rise or fall rate ∆t/∆VCC TA Power-up ramp rate 200 Operating free-air temperature −55 High-level input voltage 2 2 0.8 Outputs enabled V 0.8 10 10 −40 V ns/V µs/V 200 125 V 85 °C NOTE 4: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. *  (+#,&)#( $#($',(! -,#"%$! ( ' +#,&)4' #, "'!3( -)!' #+ "'4'/#-&'( *),)$',!$ ")) )(" #', !-'$+$)#(! ),' "'!3( 3#)/! '0)! (!,%&'(! ,'!',4'! ' ,3 # $)(3' #, "!$#((%' '!' -,#"%$! 1#% (#$' POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 
 
      

 
 
SCBS746B − JULY 2000 - REVISED OCTOBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH VCC = 2.7 V, VCC = 2.7 V to 3.6 V, II = −18 mA IOH = −100 µA VCC = 2.7 V, IOH = −8 mA IOH = −24 mA VCC = 3 V VCC = 2.7 V VOL VCC = 3 V Control inputs II Data inputs Ioff II(hold) VCC = 0 or 3.6 V, VCC = 3.6 V, VCC = 3.6 V VCC = 0, Data inputs SN54LVTH126 TYP† MAX TEST CONDITIONS MIN SN74LVTH126 TYP† MAX MIN −1.2 VCC−0.2 2.4 −1.2 V 2 2 0.2 0.2 IOL = 24 mA IOL = 16 mA 0.5 0.5 0.4 0.4 IOL = 32 mA IOL = 48 mA 0.5 0.5 0.55 10 10 VI = VCC or GND VI = VCC ±1 ±1 1 1 VI = 0 VI or VO = 0 to 4.5 V −5 VCC = 3.6 V‡, VCC = 3.6 V, VI = 0 to 3.6 V VO = 3 V V 0.55 IOL = 64 mA VI = 5.5 V VCC = 3 V V VCC−0.2 2.4 IOH = −32 mA IOL = 100 µA VI = 0.8 V VI = 2 V UNIT A µA −5 ±100 75 75 −75 −75 µA µA ±500 5 5 µA −5 −5 µA IOZPU VCC = 3.6 V, VO = 0.5 V VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don’t care ±50∗ ±50 µA IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don’t care ±50∗ ±50 µA ICC VCC = 3.6 V, IO = 0, VI = VCC or GND IOZH IOZL Outputs high 0.12 Outputs low Outputs disabled ∆ICC§ VCC = 3 V to 3.6 V, One input at VCC − 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 VO = 3 V or 0 Co 0.19 0.12 0.19 4.5 7 4.5 7 0.12 0.19 0.12 0.19 0.3 0.2 4 4 6.5 6.5 mA mA pF pF ∗ On products compliant to MIL-PRF-38535, this parameter is not production tested. † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. § This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. *  (+#,&)#( $#($',(! -,#"%$! ( ' +#,&)4' #, "'!3( -)!' #+ "'4'/#-&'( *),)$',!$ ")) )(" #', !-'$+$)#(! ),' "'!3( 3#)/! '0)! (!,%&'(! ,'!',4'! ' ,3 # $)(3' #, "!$#((%' '!' -,#"%$! 1#% (#$' 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
 
      

 
 
SCBS746B − JULY 2000 - REVISED OCTOBER 2003 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LVTH126 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A Y tPZH tPZL OE Y tPHZ tPLZ OE Y VCC = 3.3 V ± 0.3 V SN74LVTH126 VCC = 2.7 V VCC = 3.3 V ± 0.3 V VCC = 2.7 V MIN MAX MAX MIN TYP† MAX 1 4.8 5.5 1 2.3 3.8 4.5 1 4.9 5.4 1 2.4 3.9 4.4 MIN MIN UNIT MAX 1 6.4 7.1 1 3.6 5.4 6.1 1.1 6.2 6.8 1.1 3.6 5.2 5.8 1 4.8 5.3 1 2.2 3.8 4.3 1.3 6.5 7.1 1.3 3.6 5.5 6.1 ns ns ns † All typical values are at VCC = 3.3 V, TA = 25°C. *  (+#,&)#( $#($',(! -,#"%$! ( ' +#,&)4' #, "'!3( -)!' #+ "'4'/#-&'( *),)$',!$ ")) )(" #', !-'$+$)#(! ),' "'!3( 3#)/! '0)! (!,%&'(! ,'!',4'! ' ,3 # $)(3' #, "!$#((%' '!' -,#"%$! 1#% (#$' POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 
 
      

 
 
SCBS746B − JULY 2000 - REVISED OCTOBER 2003 PARAMETER MEASUREMENT INFORMATION 500 Ω From Output Under Test 6V Open S1 GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 2.7 V Input 1.5 V 1.5 V th 2.7 V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 2.7 V 1.5 V Input 1.5 V 0V VOH 1.5 V 1.5 V VOL Output tPLZ 3V 1.5 V tPZH VOH 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V Output Waveform 1 S1 at 6 V (see Note B) tPLH tPHL 1.5 V tPZL tPHL tPLH Output 2.7 V Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ 1.5 V VOH − 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) SN74LVTH126D ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVTH126 Samples SN74LVTH126DBR ACTIVE SSOP DB 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LXH126 Samples SN74LVTH126DGVR ACTIVE TVSOP DGV 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LXH126 Samples SN74LVTH126DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVTH126 Samples SN74LVTH126NSR ACTIVE SO NS 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVTH126 Samples SN74LVTH126PW ACTIVE TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LXH126 Samples SN74LVTH126PWR ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LXH126 Samples SN74LVTH126PWRG4 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LXH126 Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of