SN75155PG4

SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 D Meets or Exceeds the Requirements of D D D D D D D D OR P PACKAGE TOP VIEW ANSI EIA/TIA-232-E and ITU Recommendation V.28 10-mA Current Limited Output Wide Range of Supply Voltage VCC = 4.5 V to 15 V Low Power . . . 130 mW Built-In 5-V Regulator Response Control Provides: Input Threshold Shifting Input Noise Filtering Power-Off Output Resistance . . . 300 Ω Typ Driver Input TTL Compatible VCC − DA RY GND 1 8 2 7 3 6 4 5 VCC + DY RTC RA description The SN75155 monolithic line driver and receiver is designed to satisfy the requirements of the standard interface between data terminal equipment and data communication equipment as defined by ANSI EIA/TIA-232-E. A response control input is provided for the receiver. A resistor or a resistor and a bias voltage can be connected between the response control input and ground to provide noise filtering. The driver used is similar to the SN75188. The receiver used is similar to the SN75189A. The SN75155 is characterized for operation from 0°C to 70°C. logic symbol† DA RA RTC † logic diagram 2 7 DY VCC + DA 5 6 VCC − 3 RESP RY 1 8 2 4 GND This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12 RA RTC 5 6 7 DY Reference Regulator 3 RY Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 schematic DA VCC + 2 8 60 Ω 35 kΩ 7 300 Ω RA GND RTC VCC − 5 DY 3.5 kΩ 8.5 kΩ 4 6 55 Ω 1 3 RY absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V Supply voltage, VCC − (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −15 V Input voltage range, VI: Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −15 V to 15 V Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −30 V to 30 V Output voltage range (driver), VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −15 V to 15 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to network ground terminal. DISSIPATION RATING TABLE PACKAGE 2 TA ≤ 25 25°C C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70 70°C C POWER RATING D 725 mW 5.8 mW/°C 464 mW P 1000 mW 8.0 mW/°C 640 mW POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 recommended operating conditions MIN NOM MAX UNIT Supply voltage, VCC + 4.5 12 15 V Supply voltage, VCC − −4.5 −12 −15 V ± 15 V 25 V Output voltage, driver, VO(D) Input voltage, receiver, VI(R) −25 High-level input voltage, driver, VIH 2 V Low-level input voltage, driver, VIL Response control current Output current, receiver, IO(R) Operating free-air temperature, TA 0 0.8 V ± 5.5 mA 24 mA 70 °C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) total device PARAMETER ICCH + ICCL + ICC + ICCH − ICCL − † High-level High level supply current Low-level Low level supply current Supply current High-level High level supply current Low-level supply pp y current TEST CONDITIONS VCC + = 5 V, VCC − = − 5 V VCC + = 9 V, VCC − = − 9 V VCC + = 12 V, VCC − = − 12 V VCC + = 5 V, VCC − = − 5 V VCC + = 9 V, VCC − = − 9 V VCC + = 12V, VCC − = − 12 V VCC + = 5 V, VCC − = 0 VCC + = 9 V, VCC − = 0 VCC + = 5 V, VCC − = − 5 V VCC + = 9 V, VCC − = − 9 V VCC + = 12 V, VCC − = − 12 V VCC + = 5 V, VCC − = − 5 V VCC + = 9 V, VCC − = − 9 V VCC + = 12 V, VCC − = − 12 V MIN VI(D) = 2 V, VI(R) = 2.3 V, Output open TYP† MAX 6.3 8.1 9.1 11.9 10.4 14 VI(D) = 0.8 V, VI(R) = 0.6 V, Output open 2.5 3.4 3.7 5.1 4.1 5.6 VI(R) = 2.3 V, VI(D) = 0 4.8 6.4 6.7 9.1 VI(D) = 2 V, VI(R) = 2.3 V Output open −2.4 −3.1 −3.9 −4.9 −4.8 −6.1 VI(D) = 0.8 V, VI(R) = 0.6 V, Output open −0.2 −0.35 −0.25 −0.4 −0.27 −0.45 UNIT mA mA mA mA mA All typical values are at TA = 25°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 electrical characteristics over recommended operating free-air temperature range, VCC + = 12 V, VCC − = −12 V (unless otherwise noted) driver section PARAMETER VOH High-level High level output voltage TEST CONDITIONS VIL = 0.8 V, RL = 3 kΩ MIN TYP† MAX UNIT VCC + = 5 V, VCC − = − 5 V 3.2 3.7 VCC + = 9 V, VCC − = − 9 V 6.5 7.2 VCC + = 12 V, VCC − = − 12 V 8.9 9.8 VCC + = 5 V, VCC − = − 5 V −3.6 −3.2 VCC + = 9 V, VCC − = − 9 V −7.1 −6.4 VCC + = 12 V, VCC − = − 12 V −9.7 −8.8 5 μA −0.73 −1.2 mA V VOL Low-level L l l output t t voltage lt (see Note 2) VIH = 2 V, IIH High-level input current VI = 7 V IIL Low-level input current VI = 0 IOS(H) High level short-circuit High-level short circuit output current 0.8 8V V, VI = 0 VO = 0 −7 7 −12 12 −14.5 14 5 mA IOS(L) Low level short Low-level short-circuit circuit output current V VI = 2 V, VO = 0 65 6.5 11 5 11.5 15 mA rO Output resistance with power off VO = − 2 V to 2 V RL = 3 kΩ V Ω 300 receiver section (see Figure 1) PARAMETER TEST CONDITIONS MIN TYP† MAX UNIT VIT + Positive-going input threshhold voltage 1.2 1.9 2.3 V VIT − Negative-going input threshhold voltage 0.6 0.95 1.2 V Vhys Hystresis voltage (VIT + − VIT −) VO(H) VO(L) IIH 0.6 VI = 0.6 V, IOH = 10 μA VCC − = − 5 V 3.7 4.1 4.5 VCC + = 12 V, VCC − = − 12 V 4.4 4.7 5.2 VI = 0.6 V, IOH = 0.4 mA VCC + = 5 V, VCC − = − 5 V 3.1 3.4 3.8 VCC + = 12 V, VCC − = − 12 V 3.6 4 4.5 VI = 2.3 V, IOL = 24 mA 0.2 0.3 V 6.7 10 mA High level output voltage High-level Low-level output voltage High level input current High-level IIL Low level input current Low-level IOS Short-circuit output current V VCC + = 5 V, VI = 2 5 V 3.6 V VI = 3 V 0.43 0.67 1 mA VI = − 25 V −3.6 −6.7 −10 mA VI = − 3 V −0.43 −0.67 −1 mA −2.8 −3.7 mA VI = 0.6 V † All typical values are at TA = 25°C. NOTE 2: The algebraic limit system, in which the more positive (less negative) limit is designated as maximum, is used in this data sheet for logic voltage levels only (e.g., if − 8.8 V is the maximum, the typical value is a more negative value). 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 switching characteristics over recommended operating free-air temperature range, VCC + = 5 V, VCC − = − 5 V, CL = 50 pF (unless otherwise noted) driver section (see Figure 2) PARAMETER TEST CONDITIONS tPLH Propagation delay time, low- to high level output tPHL Propagation delay time, high- to low level output tr Output rise time tf MIN RL = 3 kΩ RL = 3 kΩ RL = 3 kΩ to 7 kΩ, CL = 2500 pF RL = 3 kΩ Output fall time RL = 3 kΩ to 7 kΩ, CL = 2500 pF TYP† MAX 250 480 80 150 67 180 ns 2.4 3 μs 48 160 ns 1.9 3 μs TYP† MAX 175 245 37 100 UNIT ns receiver section (see Figure 3) PARAMETER † TEST CONDITIONS MIN UNIT tPLH Propagation delay time, low- to high level output tPHL Propagation delay time, high- to low level output tr Output rise time RL = 400 Ω 255 360 ns tf Output fall time RL = 400 Ω 23 50 ns RL = 400 Ω ns All typical values are at TA = 25°C. PARAMETER MEASUREMENT INFORMATION VCC VIT, VI −IOH Response Control + IOL VOH VOL Open Unless Otherwise Specified RC RC CC −VC + VC Figure 1. Receiver Section Test Circuit (VIT +, VIT −, VOH, VOL) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION 3V Input 1.5 V 1.5 V See Note B 0V Output Input tPLH tPHL RL = 3 kΩ CL = 50 pF (see Note A) 90% 90% Output 50% 10% 50% 10% VOH VOL tf tr VOLTAGE WAVEFORMS TEST CIRCUIT NOTES: A. CL includes probe and jig capacitance. B. The input waveform is supplied by a generator with the following characteristics: ZO = 50 Ω, tw = 1 μs, tr ≤ 10 ns, tf ≤ 10 ns. Figure 2. Driver Section Switching Test Circuit and Voltage Waveforms Output Response Control 5V RL = 400 Ω Input 4V Input 2V 2V See Note B 0V tPHL CL = 50 pF (see Note A) tPLH 90% 90% 1.5 V 10% Output 1.5 V 10% VOL tr tf TEST CIRCUIT VOH VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The input waveform is supplied by a generator with the following characteristics: ZO = 50 Ω, tw = 1 μs, tr ≤ 10 ns, tf ≤ 10 ns. Figure 3. Receiver Section Switching Test Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 TYPICAL CHARACTERISTICS DRIVER DRIVER OUTPUT CURRENT vs OUTPUT VOLTAGE VOLTAGE TRANSFER CHARACTERISTICS 10 VCC ± = ± 12 V 8 TA = 25°C VCC ± = ± 9 V 6 IIO O − Output Current − mA VO − Output Voltage −V 20 TA = 25°C RL = 3 kΩ 4 VCC ± = ± 5 V 2 0 −2 16 VCC± = ± 5 V 12 ÁÁÁÁ ÁÁÁÁ 8 4 0 ÁÁÁ VI = 2 V −4 ÁÁ ÁÁ −4 −6 −8 3-kΩ Load Line −12 −8 VCC± = ± 12 V −16 −10 1 1.2 1.4 1.6 VI − Input Voltage − V 1.8 −20 −20 −16 −12 −8 −4 0 4 8 12 VO − Output Voltage − V 2 SLEW RATE vs LOAD CAPACITANCE SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE 400 VI = H Rise 0 −5 100 40 10 4 IOS(H) −10 VCC + = 12 V VCC − = − 12 V TA = 25°C Fall Slew Rate − V/μ s IIOS OS − Short-Circuit Output Current − mA IOS(L) 5 ÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ 1000 15 VCC + = 12 V VCC − = − 12 V VO = 0 20 DRIVER DRIVER 10 16 Figure 5 Figure 4 Á Á VI = 0.8 V VI = L 1 −15 0 10 20 30 40 50 60 TA − Free-Air Temperature − _C 70 10 Figure 6 100 1000 CL − Load Capacitance − pF 10000 Figure 7 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 TYPICAL CHARACTERISTICS RECEIVER OUTPUT VOLTAGE vs INPUT VOLTAGE RC = 3.9 kΩ VS = 5 V VO − Output Voltage − V VO 5 RC = 20 kΩ VS = − 5 V RC = Open VCC + = 12 V VCC − = − 12 V TA = 25°C 4 3 ÁÁ ÁÁ VIT + 2 VIT + VIT − VIT − VIT + VIT − 1 0 −5 −4 −3 −2 −1 0 1 2 3 4 5 VI − Input Voltage − V Figure 8 RECEIVER OUTPUT VOLTAGE vs INPUT VOLTAGE RC = 10 kΩ VS = 5 V VO − Output Voltage − V VO 5 RC = 20 kΩ VS = − 12 V RC = Open VCC + = 12 V VCC − = − 12 V TA = 25°C 4 3 ÁÁÁ ÁÁÁ VIT + 2 VIT + VIT − VIT − VIT + VIT − 1 0 −5 −4 −3 −2 −1 0 1 VI − Input Voltage − V Figure 9 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2 3 4 5 SN75155 LINE DRIVER AND RECEIVER SLLS017C − JULY 1986 − REVISED MAY 1995 TYPICAL CHARACTERISTICS RECEIVER RECEIVER INPUT THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE INPUT CURRENT vs INPUT VOLTAGE ÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ 3 10 VCC + = 12 V VCC − = − 12 V 8 IIII − Input Current − mA 6 VIT + 2 1.5 VIT − 1 4 TA = 25°C VCC + = 12 V VCC − = − 12 V 2 0 −2 −4 −6 0.5 −8 0 0 10 20 30 40 50 60 70 −10 −25 −20 −15 −10 −5 TA − Free-Air Temperature − °C 0 5 10 15 20 25 VI − Input Voltage − V Figure 10 Figure 11 RECEIVER NOISE REJECTION 9 VCC + = 12 V VCC − = − 12 V TA = 25°C 8 Input Threshold Voltage − V Input Threshold Voltage − V 2.5 ÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ 7 CC = 1000 pF CC = 500 pF CC = 300 pF CC = 100 pF CC = 10 pF 6 5 4 3 2 1 0 10 100 1000 10000 tw − Pulse Duration − ns Figure 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 13-Aug-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN75155D ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 75155 SN75155DR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 75155 SN75155DRE4 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 75155 SN75155P ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN75155P (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of