SN75462DR

 

  
      
 SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 PERIPHERAL DRIVERS FOR HIGH-VOLTAGE, HIGH-CURRENT DRIVER APPLICATIONS • • • • 1A 1B 1Y GND LOGIC SN55461 AND FK, JG SN55462 NAND FK, JG SN55463 OR FK, JG SN75461 AND D, P SN75462 NAND D, P SN75463 OR D, P 8 2 7 3 6 4 5 VCC 2B 2A 2Y SN55461, SN55462, SN55463 . . . FK PACKAGE (TOP VIEW) NC 1B NC 1Y NC SUMMARY OF SERIES 55461/75461 DEVICE 1 NC 1A NC VCC NC • • Characterized for Use to 300 mA High-Voltage Outputs No Output Latch-Up at 30 V (After Conducting 300 mA) Medium-Speed Switching Circuit Flexibility for Varied Applications and Choice of Logic Function TTL-Compatible Diode-Clamped Inputs Standard Supply Voltages Plastic DIP (P) With Copper Lead Frame for Cooler Operation and Improved Reliability Package Options Include Plastic Small Outline Packages, Ceramic Chip Carriers, and Standard Plastic and Ceramic 300-mil DIPs 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2B NC 2A NC NC GND NC 2Y NC • • • SN55461, SN55462, SN55463 . . . JG PACKAGE SN75461, SN75462, SN75463 . . . D OR P PACKAGE (TOP VIEW) PACKAGES NC − No internal connection description These dual peripheral drivers are functionally interchangeable with SN55451B through SN55453B and SN75451B through SN75453B peripheral drivers, but are designed for use in systems that require higher breakdown voltages than those devices can provide at the expense of slightly slower switching speeds. Typical applications include logic buffers, power drivers, relay drivers, lamp drivers, MOS drivers, line drivers, and memory drivers. The SN55461/SN75461, SN55462/SN75462, and SN55463/SN75463 are dual peripheral AND, NAND, and OR drivers respectively (assuming positive logic), with the output of the gates internally connected to the bases of the npn output transistors. Series SN55461 drivers are characterized for operation over the full military temperature range of − 55°C to 125°C. Series SN75461 drivers are characterized for operation from 0°C to 70°C. Copyright  1995, Texas Instruments Incorporated     ! "#$ !  %#&'" ($) (#"! "  !%$""! %$ *$ $!  $+! !#$! !(( ,-) (#" %"$!!. ($!  $"$!!'- "'#($ $!.  '' %$$!) • DALLAS, TEXAS 75265 • HOUSTON, TEXAS 77251−1443 POST OFFICE BOX 655303 POST OFFICE BOX 1443 1 
 

  
      
 SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† SN55’ Supply voltage, VCC (see Note 1) SN75’ UNIT 7 7 V Input voltage, VI 5.5 5.5 V Intermitter voltage (see Note 2) 5.5 5.5 V Off-state output voltage, VO 35 35 V Continuous collector or output current (see Note 3) 400 400 mA Peak collector or output current (tw ≤ 10 ms, duty cycle ≤ 50%, see Note 4) 500 500 mA Continuous total power dissipation See Dissipation Rating Table Operating free-air temperature range, TA Storage temperature range, Tstg −55 to 125 0 to 70 °C −65 to 150 −65 to 150 °C Case temperature for 60 seconds, TC FK package 260 °C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds JG package 300 °C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds D or P package 260 °C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. Voltage values are with respect to network GND unless otherwise specified. 2. This is the voltage between two emitters A and B. 3. This value applies when the base-emitter resistance (RBE) is equal to or less than 500 Ω. 4. Both halves of these dual circuits may conduct rated current simultaneously; however, power dissipation averaged over a short time interval must fall within the continuous dissipation rating. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C 25 C POWER RATING D 725 mW FK JG P DERATING FACTOR ABOVE TA = 25°C TA = 70 70°C C POWER RATING TA = 125 125°C C POWER RATING 5.8 mW/°C 464 mW − 1375 mW 11.0 mW/°C 880 mW 275 mW 1050 mW 8.4 mW/°C 672 mW 210 mW 1000 mW 8.0 mW/°C 640 mW − recommended operating conditions SN55’ Supply voltage, VCC High-level input voltage, VIH MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.75 5 5.25 2 Low-level input voltage, VIL 2 0.8 Operating free-air temperature, TA 2 SN75’ −55 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 125 0 UNIT V V 0.8 V 70 °C 
 

  
      
 SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 logic symbol† 1A 1B 2A 2B logic diagram (positive logic) 1 & 2 3 6 5 7 1Y 1A 1B 2Y 2A 2B † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for D, JG, and P packages. B Y L L L (on state) L (on state) L H H L L (on state) H H H (off state) 1Y 2 5 6 2Y 7 4 GND schematic (each driver) FUNCTION TABLE (each driver) A 3 1 VCC 4 kΩ 1.6 kΩ 130 Ω Y A positive logic: Y = AB or A + B B 500 Ω 1 kΩ GND Resistor values shown are nominal. electrical characteristics over recommended operating free-air temperature range TEST CONDITIONS† PARAMETER VIK IOH VOL MIN Input clamp voltage VCC = MIN, II = − 12 mA High-level output current VCC = MIN, VOH = 35 V VIH = MIN, Low-level output voltage II IIH Input current at maximum input voltage IIL ICCH Low-level input current High-level input current SN55461 TYP‡ MAX −1.2 MIN SN75461 TYP‡ MAX −1.5 −1.2 300 −1.5 V 100 µA A VCC = MIN, VIL = 0.8 V, IOL = 100 mA 0.25 0.5 0.25 0.4 VCC = MIN, VIL = 0.8 V, IOL = 300 mA 0.5 0.8 0.5 0.7 VCC = MAX, VCC = MAX, VI = 5.5 V VI = 2.4 V VCC = MAX, VCC = MAX, VI = 0.4 V VI = 5 V UNIT V 1 1 mA 40 40 µA −1 −1.6 −1 −1.6 mA 8 11 8 11 mA ICCL Supply current, outputs low VCC = MAX, VI = 0 56 76 56 † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 5 V, TA = 25°C. 76 mA Supply current, outputs high switching characteristics, VCC = 5 V, TA = 25°C PARAMETER TEST CONDITIONS tPLH tPHL Propagation delay time, low-to-high-level output tTLH tTHL Transition time, low-to-high-level output VOH Propagation delay time, high-to-low-level output IO ≈ 200 mA, RL = 50 Ω,, MIN CL = 15 pF, See Figure 1 Transition time, high-to-low-level output High-level output voltage after switching SN55461 VS = 30 V, See Figure 2 SN75461 • • MAX 30 55 25 40 8 20 10 20 VS −10 IO ≈ 300 mA, POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 TYP VS −10 UNIT ns mV 3 
 

  
      
 SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 logic symbol† 1A 1B 2A 2B logic diagram (positive logic) 1 & 2 3 6 5 7 1Y 1A 1B 2Y 2A 2B 3 1 2 5 6 4 Y L L H (off state) L H H (off state) H L H (off state) H H L (on state) GND schematic (each driver) FUNCTION TABLE (each driver) B 2Y 7 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for D, JG, and P packages. A 1Y VCC 1.6 kΩ 1.6 kΩ 4 kΩ 130 Ω Y A positive logic: Y = AB or A + B B 1 kΩ 500 Ω 1 kΩ GND Resistor values shown are nominal. electrical characteristics over recommended operating free-air temperature range TEST CONDITIONS† PARAMETER VIK IOH VOL Input clamp voltage VCC = MIN, II = − 12 mA High-level output current VCC = MIN, VOH = 35 V VIL = 0.8 V, Low-level output voltage II IIH Input current at maximum input voltage IIL ICCH Low-level input current High-level input current MIN SN55462 TYP‡ MAX −1.2 MIN SN75462 TYP‡ MAX −1.5 −1.2 300 −1.5 V 100 µA A VCC = MIN, VIH = MIN, IOL = 100 mA 0.25 0.5 0.25 0.4 VCC = MIN, VIH = MIN, IOL = 300 mA 0.5 0.8 0.5 0.7 VCC = MAX, VCC = MAX, VI = 5.5 V VI = 2.4 V VCC = MAX, VCC = MAX, VI = 0.4 V VI = 0 UNIT V 1 1 40 40 mA µA −1.1 −1.6 −1.1 −1.6 mA 13 17 13 17 mA ICCL Supply current, outputs low VCC = MAX, VI = 5 V 61 76 61 † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 5 V, TA = 25°C. 76 mA Supply current, outputs high switching characteristics, VCC = 5 V, TA = 25°C PARAMETER TEST CONDITIONS tPLH tPHL Propagation delay time, low-to-high-level output tTLH tTHL Transition time, low-to-high-level output VOH 4 Propagation delay time, high-to-low-level output IO ≈ 200 mA, RL = 50 Ω,, CL = 15 pF, See Figure 1 VS = 30 V, See Figure 2 IO ≈ 300 mA, MIN Transition time, high-to-low-level output High-level output voltage after switching SN55462 SN75462 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • TYP MAX 45 65 30 50 13 25 10 20 VS −10 VS −10 UNIT ns mV 
 

  
      
 SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 logic symbol† 1A 1B 2A 2B logic diagram (positive logic) 1 ≥1 2 3 6 5 7 1Y 1A 5 6 2A 4 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for D, JG, and P packages. B Y L L (on state) L H H (off state) H L H (off state) H H GND schematic (each driver) FUNCTION TABLE (each driver) L 2Y 7 2B A 1Y 2 1B 2Y 3 1 VCC 4 kΩ 1.6 kΩ 130 Ω 4 kΩ Y A H (off state) positive logic: Y = A + B or A B B 500 Ω 1 kΩ GND Resistor values shown are nominal. electrical characteristics over recommended operating free-air temperature range TEST CONDITIONS† PARAMETER VIK IOH VOL Input clamp voltage VCC = MIN, II = − 12 mA High-level output current VCC = MIN, VOH = 35 V VIH = MIN, Low-level output voltage II IIH Input current at maximum input voltage IIL ICCH Low-level input current High-level input current MIN SN55463 MAX TYP‡ −1.2 MIN SN75463 MAX TYP‡ −1.5 −1.2 300 −1.5 V 100 µA A VCC = MIN, VIL = 0.8 V, IOL = 100 mA 0.25 0.5 0.25 0.4 VCC = MIN, VIL = 0.8 V, IOL = 300 mA 0.5 0.8 0.5 0.7 VCC = MAX, VCC = MAX, VI = 5.5 V VI = 2.4 V VCC = MAX, VCC = MAX, VI = 0.4 V VI = 5 V UNIT V 1 1 mA 40 40 µA −1 −1.6 −1 −1.6 mA 8 11 8 11 mA ICCL Supply current, outputs low VCC = MAX, VI = 0 58 76 58 † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 5 V, TA = 25°C. 76 mA Supply current, outputs high switching characteristics, VCC = 5 V, TA = 25°C PARAMETER TEST CONDITIONS tPLH tPHL Propagation delay time, low-to-high-level output tTLH tTHL Transition time, low-to-high-level output VOH Propagation delay time, high-to-low-level output IO ≈ 200 mA, RL = 50 Ω,, CL = 15 pF, See Figure 1 VS = 30 V, See Figure 2 IO ≈ 300 mA, MIN Transition time, high-to-low-level output High-level output voltage after switching SN55463 SN75463 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • TYP MAX 30 55 25 40 8 25 10 25 VS −10 VS −10 UNIT ns mV 5 
 

  
      
 SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 PARAMETER MEASUREMENT INFORMATION ≤ 10 ns ≤ 5 ns Input 2.4 V 10 V RL = 50 Ω ’461 ’462 Output Pulse Generator (see Note A) 90% 1.5 V Input ’461 ’463 Circuit Under Test (see Note B) 10% 10% 0V 0.5 µs ≤ 5 ns Input ’462 CL = 15 pF (see Note B) 90% 1.5 V ≤ 10 ns 3V 90% 1.5 V 10% 10% tPHL GND ’463 tPLH 90% SUB 3V 90% 1.5 V 90% 50% 10% Output 0V VOH 50% 10% VOL 0.4 V tTLH tTHL VOLTAGE WAVEFORMS TEST CIRCUIT NOTES: A. The pulse generator has the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω. B. CL includes probe and jig capacitance. Figure 1. Test Circuit and Voltage Waveforms for Switching Times ≤ 5 ns VS = 30 V Input 2.4 V ’461 ’462 Input ’461 ’463 2 mH 5V 90% 90% 1.5 V Circuit Under Test (see Note B) 10% CL = 15 pF (see Note B) 10% 0V 40 µs ≤ 5 ns 90% Input ’462 3V 1.5 V 65 Ω 1N3064 Output Pulse Generator (see Note A) ≤ 10 ns 1.5 V ≤ 10 ns 3V 90% 1.5 V 10% 10% 0V VOH ’463 GND SUB Output VOL 0.4 V VOLTAGE WAVEFORMS TEST CIRCUIT NOTES: A. The pulse generator has the following characteristics: PRR ≤ 12.5 kHz, ZO = 50 Ω . B. CL includes probe and jig capacitance. Figure 2. Test Circuit and Voltage Waveforms for Latch-Up Test 6 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) JM38510/12908BPA ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510 /12908BPA Samples M38510/12908BPA ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510 /12908BPA Samples SN75462D ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 75462 Samples SN75462DR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 75462 Samples SN75462P ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN75462P Samples SN75462PE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN75462P Samples SN75463P ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN75463P Samples SNJ55462FK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SNJ55 462FK Samples SNJ55462JG ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SNJ55462JG Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of