SNJ54HCU04J


   
SCLS079E − MARCH 1984 − REVISED MARCH 2004 D Wide Operating Voltage Range of 2 V to 6 V D Outputs Can Drive Up To 10 LSTTL Loads D Low Power Consumption, 20-µA Max ICC D D D D Typical tpd = 7 ns ±4-mA Output Drive at 5 V Low Input Current of 1 µA Max Unbuffered Outputs SN54HCU04 . . . J OR W PACKAGE SN74HCU04 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) 1 14 2 13 3 12 4 11 5 10 6 9 7 8 1Y 1A NC VCC 6A VCC 6A 6Y 5A 5Y 4A 4Y 2A NC 2Y NC 3A 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 6Y NC 5A NC 5Y 3Y GND NC 4Y 4A 1A 1Y 2A 2Y 3A 3Y GND SN54HCU04 . . . FK PACKAGE (TOP VIEW) NC − No internal connection description/ordering information The ’HCU04 devices contain six independent inverters. They perform the Boolean function Y = A in positive logic. ORDERING INFORMATION PACKAGE† TA PDIP − N SN74HCU04N Tube of 50 SN74HCU04D Reel of 2500 SN74HCU04DR Reel of 250 SN74HCU04DT SOP − NS Reel of 2000 SN74HCU04NSR HCU04 SSOP − DB Reel of 2000 SN74HCU04DBR HU04 Reel of 90 SN74HCU04PW Reel of 2000 SN74HCU04PWR Reel of 250 SN74HCU04PWT CDIP − J Tube of 25 SNJ54HCU04J SNJ54HCU04J CFP − W Tube of 150 SNJ54HCU04W SNJ54HCU04W LCCC − FK Tube of 55 SNJ54HCU04FK TSSOP − PW −55°C −55 C to 125 125°C C TOP-SIDE MARKING Tube of 25 SOIC − D −40°C −40 C to 85 85°C C ORDERABLE PART NUMBER SN74HCU04N HCU04 HCU04 SNJ54HCU04FK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2004, Texas Instruments Incorporated      !   "#$ %!& %   "! "! '! !  !( ! %% )*& % "!+ %!  !!$* $%! !+  $$ "!!&  "% "$  , -./.010 $$ "!! ! !!% $! '!)! !%&  $$ '! "% "% "!+ %!  !!$* $%! !+  $$ "!!& POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 

   
SCLS079E − MARCH 1984 − REVISED MARCH 2004 FUNCTION TABLE (each inverter) INPUT A OUTPUT Y H L L H logic diagram (positive logic) A Y absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) SN54HCU04 VCC VIH VIL VI VO Supply voltage High-level input voltage Low-level input voltage SN74HCU04 MIN NOM MAX 2 5 6 MIN NOM MAX 2 5 6 VCC = 2 V VCC = 4.5 V 1.7 1.7 3.6 3.6 VCC = 6 V VCC = 2 V 4.8 4.8 VCC = 4.5 V VCC = 6 V Input voltage 0 Output voltage 0 0.5 0.5 1.35 1.8 1.8 0 0 V V 1.35 VCC VCC UNIT VCC VCC V V V TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 

   
SCLS079E − MARCH 1984 − REVISED MARCH 2004 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = −20 µA VOH VI = VCC or GND IOH = −4 mA IOH = −5.2 mA IOL = 20 µA VOL VI = VCC or GND IOL = 4 mA IOL = 5.2 mA II ICC VI = VCC or 0 VI = VCC or 0, IO = 0 TA = 25°C TYP MAX SN74HCU04 MIN 2V 1.8 1.8 4 4 4 6V 5.5 5.5 5.5 4.5 V 3.98 3.7 3.84 6V 5.48 4.5 V MIN MAX MIN MAX UNIT 1.8 5.2 V 5.34 2V 0.2 0.2 0.2 4.5 V 0.5 0.5 0.5 6V 0.5 0.5 0.5 4.5 V 0.26 0.4 0.33 6V 0.26 0.4 0.33 6V ±100 ±1000 ±1000 nA 2 40 20 µA 10 10 10 pF 6V Ci SN54HCU04 VCC 2 V to 6 V 3 V switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) TA = 25°C TYP MAX SN54HCU04 SN74HCU04 PARAMETER FROM (INPUT) TO (OUTPUT) VCC 2V 40 80 120 100 tpd A Y 4.5 V 8 16 24 20 6V 7 14 20 17 tf Y MIN MIN MAX MIN MAX 2V 38 75 110 95 4.5 V 8 15 22 19 6V 6 13 19 16 UNIT ns ns operating characteristics, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per inverter POST OFFICE BOX 655303 No load • DALLAS, TEXAS 75265 TYP 20 UNIT pF 3 

   
SCLS079E − MARCH 1984 − REVISED MARCH 2004 PARAMETER MEASUREMENT INFORMATION From Output Under Test Test Point Input 50% VCC 50% 0V CL = 50 pF (see Note A) tPLH In-Phase Output LOAD CIRCUIT tPHL 90% 50% 10% 90% tr † tPHL Input 50% 10% 90% 90% tr VCC 50% 10% 0 V tf Out-of-Phase Output 90% VOH 50% 10% VOL tf tPLH 50% 10% tf 50% 10% 90% VOH VOL tr † † tr is not applicable to ’HCU devices. VOLTAGE WAVEFORM INPUT RISE AND FALL TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES NOTES: A. CL includes probe and test-fixture capacitance. B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns. C. The outputs are measured one at a time, with one input transition per measurement. D. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 2-Dec-2023 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 86010012A ACTIVE LCCC FK 20 55 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 86010012A SNJ54HCU 04FK 8601001CA ACTIVE CDIP J 14 25 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8601001CA SNJ54HCU04J Samples SN54HCU04J ACTIVE CDIP J 14 25 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SN54HCU04J Samples Samples SN74HCU04D LIFEBUY SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCU04 SN74HCU04DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM -40 to 85 HCU04 SN74HCU04DT LIFEBUY SOIC D 14 250 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCU04 SN74HCU04N ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74HCU04N Samples SN74HCU04NE4 ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74HCU04N Samples SN74HCU04NSR ACTIVE SO NS 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCU04 Samples Samples SN74HCU04PW LIFEBUY TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCU04 SN74HCU04PWR ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM -40 to 85 HCU04 Samples SN74HCU04PWRG4 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCU04 Samples SN74HCU04PWT LIFEBUY TSSOP PW 14 250 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCU04 SNJ54HCU04FK ACTIVE LCCC FK 20 55 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 86010012A SNJ54HCU 04FK SNJ54HCU04J ACTIVE CDIP J 14 25 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8601001CA SNJ54HCU04J (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples Samples PACKAGE OPTION ADDENDUM www.ti.com 2-Dec-2023 (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of