TLC25L2CDR

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 D D D D D D D, P, OR PW PACKAGE (TOP VIEW) A-Suffix Versions Offer 5-mV VIO B-Suffix Versions Offer 2-mV VIO Wide Range of Supply Voltages 1.4 V to 16 V True Single-Supply Operation Common-Mode Input Voltage Includes the Negative Rail Low Noise . . . 30 nV/√Hz Typ at f = 1 kHz (High-Bias Versions) 1OUT 1IN – 1IN + VDD – /GND 1 8 2 7 3 6 4 5 VDD 2OUT 2IN – 2IN + symbol (each amplifier) description + IN + The TLC252, TLC25L2, and TLC25M2 are OUT IN – – low-cost, low-power dual operational amplifiers designed to operate with single or dual supplies. These devices utilize the Texas Instruments silicon gate LinCMOS process, giving them stable input offset voltages that are available in selected grades of 2, 5, or 10 mV maximum, very high input impedances, and extremely low input offset and bias currents. Because the input common-mode range extends to the negative rail and the power consumption is extremely low, this series is ideally suited for battery-powered or energy-conserving applications. The series offers operation down to a 1.4-V supply, is stable at unity gain, and has excellent noise characteristics. These devices have internal electrostatic-discharge (ESD) protection circuits that prevent catastrophic failures at voltages up to 2000 V as tested under MIL-STD-883C, Method 3015.1. However, care should be exercised in handling these devices as exposure to ESD may result in a degradation of the device parametric performance. AVAILABLE OPTIONS TA 0°C to 70°C VIOmax AT 25°C PACKAGED DEVICES SMALL OUTLINE (D) PLASTIC DIP (P) TSSOP (PW) CHIP FORM (Y) 10 mV 5 mV 2 mV TLC252CD TLC252ACD TLC252BCD TLC252CP TLC252ACP TLC252BCP TLC252CPW TLC252ACPW TLC252BCPW TLC252Y — — 10 mV 5 mV 2 mV TLC25L2CD TLC25L2ACD TLC25L2BCD TLC25L2CP TLC25L2ACP TLC25L2BCP TLC25L2CPW TLC25L2ACPW TLC25L2BCPW TLC25L2Y — — 10 mV 5 mV 2 mV TLC25M2CD TLC25M2ACD TLC25M2BCD TLC25M2CP TLC25M2ACP TLC25M2BCP — — — TLC25M2Y — — The D package is available taped and reeled. Add the suffix R to the device type (e.g., TLC252CDR). Chips are tested at 25°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. LinCMOS is a trademark of Texas Instruments. Copyright  2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 description (continued) Because of the extremely high input impedance and low input bias and offset currents, applications for the TLC252/ 25_2 series include many areas that have previously been limited to BIFET and NFET product types. Any circuit using high-impedance elements and requiring small offset errors is a good candidate for cost-effective use of these devices. Many features associated with bipolar technology are available with LinCMOS operational amplifiers without the power penalties of traditional bipolar devices. General applications such as transducer interfacing, analog calculations, amplifier blocks, active filters, and signal buffering are all easily designed with the TLC252 / 25_2 series devices. Remote and inaccessible equipment applications are possible using their low-voltage and low-power capabilities. The TLC252 / 25_2 series is well suited to solve the difficult problems associated with single-battery and solar-cell-powered applications. This series includes devices that are characterized for the commercial temperature range and are available in 8-pin plastic dip and the small-outline package. The device is also available in chip form. The TLC252 / 25_2 series is characterized for operation from 0°C to 70°C. equivalent schematic (each amplifier) VDD IN + IN – 8 3, 5 ESDProtective Network 2, 6 ESDProtective Network 1, 7 VDD – /GND 2 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 OUT TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 TLC252Y, TLC25L2Y, and TLC25M2Y chip information These chips, properly assembled, display characteristics similar to the TLC252 / 25_2. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform. BONDING PAD ASSIGNMENTS (5) (4) (3) VDD (8) (3) + 1IN + (6) (2) – 1IN – 2OUT 60 (1) 1OUT (2) + (7) – (5) (6) 2IN + 2IN – (4) VDD – /GND CHIP THICKNESS: 15 TYPICAL (1) (7) BONDING PADS: 4 × 4 MINIMUM TJMAX = 150°C (8) TOLERANCES ARE ± 10%. 73 ALL DIMENSIONS ARE IN MILS. PIN (4) IS INTERNALLY CONNECTED TO BACKSIDE OF CHIP. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 18 V Duration of short circuit at (or below) 25°C free-air temperature (see Note 3) . . . . . . . . . . . . . . . . . . unlimited Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to VDD – /GND. 2. Differential voltages are at IN+, with respect to IN –. 3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING D 725 mW 5.8 mW/°C 464 mW P 1000 mW 8.0 mW/°C 640 mW PW 525 mW 4.2 mW/°C 336 mW PACKAGE recommended operating conditions MIN Supply voltage, VDD Common mode input voltage, Common-mode voltage VIC VDD = 1.4 V VDD = 5 V VDD = 10 V VDD = 16 V Operating free-air temperature, TA 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MAX 1.4 16 0 0.2 – 0.2 4 – 0.2 9 – 0.2 14 0 70 UNIT V V °C TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 1.4 V (unless otherwise noted) PARAMETER TLC25_2C VIO Input offset voltage TLC25_2AC TLC252_C TEST CONDITIONS† 2V VO = 0 0.2 V, RS = 50 Ω TLC25_2BC MIN TLC25L2_C MAX MIN TYP TLC25M2_C MAX MIN TYP MAX 25°C 10 10 10 0°C to 70°C 12 12 12 25°C 5 5 5 0°C to 70°C 6.5 6.5 6.5 25°C 2 2 2 0°C to 70°C 3 3 3 αVIO Average temperature coefficient of input offset voltage IIO Input offset current VO = 0.2 V 0°C to 70°C IIB Input bias current VO = 0.2 V 0°C to 70°C 25°C to 70°C 1 25°C 1 VICR Common-mode input voltage range VOM Peak output voltage swing‡ AVD Large-signal differential voltage amplification CMRR Common-mode rejection ratio IDD Supply current 1 60 1 0 to 0.2 VID = 100 mV 25°C 450 VO = 100 to 300 mV, RS = 50 Ω 25°C 60 1 25°C 700 1 700 600 450 20 77 60 77 375 25 60 34 pA 60 0 to 0.2 450 mV 60 300 60 0 to 0.2 300 1 600 10 60 60 UNIT µV/°C 1 300 600 25°C 25°C 1 300 25°C VO = 0.2 V, VIC = VICRmin VO = 0.2 V, No load TYP pA V 700 mV 20 V/mV 77 dB 200 250 µA † All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Unless otherwise noted, an output load resistor is connected from the output to ground and has the following value: for low bias RL = 1 MΩ, for medium bias RL = 100 kΩ, and for high bias RL = 10 kΩ. ‡ The output swings to the potential of VDD – /GND. operating characteristics, VDD = 1.4 V, TA = 25°C PARAMETER TEST CONDITIONS B1 Unity-gain bandwidth AV = 40 dB, CL = 10 pF, RS = 50 Ω SR Slew rate at unity gain Overshoot factor TLC252_C MIN TYP TLC25L2_C MAX MIN TYP 12 12 See Figure 1 0.1 See Figure 1 30% POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MAX TLC25M2_C MIN TYP MAX UNIT 12 kHz 0.001 0.01 V/µs 35% 35% 5 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC252C, TLC252AC, TLC252BC MIN TLC252C VIO Input offset voltage VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 10 kΩ VIC = 0,, RL = 10 kΩ Full range TLC252BC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 10 kΩ Full range IIO Input offset current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V IIB Input bias current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V VOH VOL Low-level output voltage VID = 100 mV, RL = 10 kΩ VID = – 100 mV, IOL = 0 CMRR kSVR IDD Large-signal L i l differential diff ti l voltage lt am lification amplification Common-mode rejection ratio VO = 0.25 V to 2 V, RL = 10 kΩ VIC = VICRmin Supply-voltage S l lt rejection j ti ratio ti (∆VDD /∆VDD) VDD = 5 V to 10 V, Supply current (two amplifiers) VO = 2 2.5 5V V, No load VO = 1.4 V VIC = 2 2.5 5V V, 0.23 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 2 3 µV/°C 25°C to 70°C 1.8 25°C 0.1 60 70°C 7 300 25°C 0.6 60 70°C 40 600 25°C – 0.2 to 4 Full range – 0.2 to 3.5 – 0.3 to 4.2 pA pA V V 25°C 3.2 3.8 0°C 3 3.8 70°C 3 3.8 V 25°C 0 50 0°C 0 50 0 50 25°C 5 23 0°C 4 27 70°C 4 20 25°C 65 80 0°C 60 84 70°C 60 85 25°C 65 95 0°C 60 94 70°C 60 96 mV V/mV dB dB 25°C 1.4 3.2 0°C 1.6 3.6 70°C 1.2 2.6 † Full range is 0°C to 70°C. NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. 6 5 6.5 70°C AVD 10 0.9 25°C Common-mode input voltage g range (see Note 5) High-level output voltage 1.1 UNIT 12 25°C VO = 1.4 V,, RS = 50 Ω, Average temperature coefficient of input offset voltage MAX Full range TLC252AC αVIO VICR 25°C TYP mA TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLC252C, TLC252AC, TLC252BC MIN TLC252C VIO Input offset voltage VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 10 kΩ Full range TLC252BC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 10 kΩ Full range IIO Input offset current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V IIB Input bias current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V VOH VOL Low-level output voltage RL = 10 kΩ VID = – 100 mV, IOL = 0 0.29 CMRR kSVR IDD Large-signal L i l differential diff ti l voltage lt am lification amplification Common-mode rejection ratio VO = 1 V to 6 V, RL = 10 kΩ VIC = VICRmin Supply-voltage S l lt rejection j ti ratio ti (∆VDD /∆VDD) VDD = 5 V to 10 V, Supply current (two amplifiers) VO = 5 V V, No load VO = 1.4 V VIC = 5 V, V mV 2 3 µV/°C 2 25°C 0.1 60 70°C 7 300 25°C 0.6 60 70°C 50 600 25°C – 0.2 to 9 Full range – 0.2 to 8.5 – 0.3 to 9.2 pA pA V V 25°C 8 8.5 0°C 8 8.5 70°C 7.8 8.4 V 25°C 0 50 0°C 0 50 0 50 70°C AVD 5 6.5 25°C to 70°C VID = 100 mV, 10 0.9 25°C Common-mode input voltage g range (see Note 5) High-level output voltage 1.1 UNIT 12 25°C VO = 1.4 V,, RS = 50 Ω, Average temperature coefficient of input offset voltage MAX Full range TLC252AC αVIO VICR 25°C VIC = 0,, RL = 10 kΩ TYP 25°C 10 36 0°C 7.5 42 70°C 7.5 32 25°C 65 85 0°C 60 88 70°C 60 88 25°C 65 95 0°C 60 94 70°C 60 96 mV V/mV dB dB 25°C 1.9 4 0°C 2.3 4.4 70°C 1.6 3.4 mA † Full range is 0°C to 70°C. NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 operating characteristics, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC252C, TLC252AC, TLC252BC MIN VI(PP) ( )=1V SR Slew rate at unity gain RL = 10 kΩ,, See Figure 1 CL = 20 pF,, VI(PP) ( ) = 2.5 V Vn BOM B1 φm Equivalent input noise voltage Maximum output-swing bandwidth Unity-gain bandwidth Phase margin f = 1 kHz, VO = VOH, See Figure VI = 10 mV, VI = 10 mV, mV See Figure 3 RS = 20 Ω, F CL = 20 pF, CL = 20 pF, f = B1, See Figure 2 RL = 100 kΩ, kΩ See Figure 3 CL = 20 pF, pF TYP 25°C 3.6 0°C 4 70°C 3 25°C 2.9 0°C 3.1 70°C 2.5 25°C 25 25°C 320 0°C 340 70°C 260 25°C 1.7 0°C 2 70°C 1.3 25°C 46° 0°C 47° 70°C 43° UNIT MAX V/µs nV/√Hz kHz MHz operating characteristics, VDD = 10 V PARAMETER TEST CONDITIONS TA TLC252C, TLC252AC, TLC252BC MIN VI(PP) ( )=1V SR Slew rate at unity gain RL = 10 kΩ,, See Figure 1 CL = 20 pF,, VI(PP) ( ) = 5.5 V Vn Equivalent input noise voltage f = 1 kHz, RS = 20 Ω, See Figure 2 BOM Maximum output-swing bandwidth VO = VOH, See Figure 1 CL = 20 pF, F RL = 100 kΩ, kΩ B1 φm 8 Unity-gain bandwidth Phase margin VI = 10 mV, mV VI = 10 mV, See Figure 3 CL = 20 pF, f = B1, POST OFFICE BOX 655303 See Figure 3 pF CL = 20 pF, • DALLAS, TEXAS 75265 TYP 25°C 5.3 0°C 5.9 70°C 4.3 25°C 4.6 0°C 5.1 70°C 3.8 25°C 25 25°C 200 0°C 220 70°C 140 25°C 2.2 0°C 2.5 70°C 1.8 25°C 49° 0°C 50° 70°C 46° UNIT MAX V/µs nV/√Hz kHz MHz TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLC25L2C TLC25L2AC TLC25L2BC MIN VIO Input offset voltage VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 1 MΩ Full range TLC252AC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 1 MΩ Full range TLC252BC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 1 MΩ αVIO Average temperature coefficient of input offset voltage IIO Input offset current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V IIB Input bias current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V VICR VOH VOL AVD CMRR kSVR IDD 25°C TLC252C Low-level output voltage Large-signal L i l differential diff ti l voltage lt amplification am lification Common-mode rejection ratio VID = 100 mV, VDD = 5 V to 10 V, Supply current (two amplifiers) VO = 2 2.5 5V V, No load 10 5 6.5 0.204 3 µV/°C 1.1 25°C 0.1 60 70°C 7 300 25°C 0.6 60 70°C 50 600 RL = 1 MΩ VO = 1.4 V VIC = 2 2.5 5V V, mV 2 25°C to 70°C VIC = VICRmin S l lt j ti ratio ti Supply-voltage rejection (∆VDD /∆VDD) 1.1 Full range IOL = 0 VO = 0.25 V to 2 V, MAX 0.9 25°C RL = 1 MΩ VID = – 100 mV, TYP 12 25°C 25°C – 0.2 to 4 Full range – 0.2 to 3.5 Common-mode input voltage g range (see Note 5) High-level output voltage UNIT – 0.3 to 4.2 pA pA V V 25°C 3.2 4.1 0°C 3 4.1 70°C 3 4.2 V 25°C 0 50 0°C 0 50 70°C 0 50 25°C 50 700 0°C 50 700 70°C 50 380 25°C 65 94 0°C 60 95 70°C 60 95 25°C 70 97 0°C 60 97 70°C 60 98 mV V/mV dB dB 25°C 20 34 0°C 24 42 70°C 16 28 µA † Full range is 0°C to 70°C. NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC25L2C TLC25L2AC TLC25L2BC MIN VIO Input offset voltage VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 1 MΩ Full range TLC252AC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 1 MΩ Full range TLC252BC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 1 MΩ αVIO Average temperature coefficient of input offset voltage IIO Input offset current (see Note 4) VO = 5 V V, VIC = 5 V IIB Input bias current (see Note 4) VO = 5 V V, VIC = 5 V VICR VOH VOL AVD CMRR kSVR IDD 25°C TLC252C Low-level output voltage Large-signal L i l differential diff ti l voltage lt amplification am lification Common-mode rejection ratio RL = 1 MΩ VID = – 100 mV, IOL = 0 VO = 1 V to 6 V, RL = 1 MΩ VIC = VICRmin S l lt j ti ratio ti Supply-voltage rejection (∆VDD /∆VDD) VDD = 5 V to 10 V, Supply current (two amplifiers) VO = 5 V V, No load VO = 1.4 V VIC = 5 V, V MAX 1.1 10 0.9 25°C 0.235 Full range POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 2 3 µV/°C 1 25°C 0.1 60 70°C 8 300 25°C 0.7 60 70°C 50 600 25°C – 0.2 to 9 Full range – 0.2 to 8.5 – 0.3 to 9.2 pA pA V V 25°C 8 8.9 0°C 7.8 8.9 70°C 7.8 8.9 V 25°C 0 50 0°C 0 50 70°C 0 50 25°C 50 860 0°C 50 1025 70°C 50 660 25°C 65 97 0°C 60 97 70°C 60 97 25°C 70 97 0°C 60 97 70°C 60 98 mV V/mV dB dB 25°C 29 46 0°C 36 66 70°C 22 40 † Full range is 0°C to 70°C. NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. 10 5 6.5 25°C to 70°C VID = 100 mV, TYP 12 25°C Common-mode input voltage g range (see Note 5) High-level output voltage UNIT µA TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 operating characteristics, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC25L2C TLC25L2AC TLC25L2BC MIN VI(PP) ( )=1V SR Slew rate at unity gain RL = 1 MΩ,, See Figure 1 CL = 20 pF,, VI(PP) ( ) = 2.5 V Vn BOM B1 φm Equivalent input noise voltage Maximum M i output-swing t t i bandwidth Unity-gain bandwidth Phase margin f = 1 kHz, VO = VOH, See Figure VI = 10 mV, VI = 10 mV, mV See Figure 3 RS = 20 Ω, CL = 20 pF, F CL = 20 pF, f = B1, See Figure 2 RL = 1 MΩ, MΩ See Figure 3 CL = 20 pF, pF TYP 25°C 0.03 0°C 0.04 70°C 0.03 25°C 0.03 0°C 0.03 70°C 0.02 25°C 68 25°C 5 0°C 6 70°C 4.5 25°C 85 0°C 100 70°C 65 25°C 34° 0°C 36° 70°C 30° UNIT MAX V/µs nV/√Hz kHz MHz operating characteristics, VDD = 10 V PARAMETER TEST CONDITIONS TA TLC25L2C TLC25L2AC TLC25L2BC MIN VI(PP) ( )=1V SR Slew rate at unity gain RL = 1 MΩ,, See Figure 1 CL = 20 pF,, VI(PP) ( ) = 5.5 V Vn Equivalent input noise voltage f = 1 kHz, RS = 20 Ω, See Figure 2 BOM Maximum M i output-swing t t i bandwidth VO = VOH, See Figure 1 CL = 20 pF, F RL = 1 MΩ, MΩ B1 φm Unity-gain bandwidth Phase margin VI = 10 mV, mV VI = 10 mV, See Figure 3 CL = 20 pF, f = B1, POST OFFICE BOX 655303 See Figure 3 pF CL = 20 pF, • DALLAS, TEXAS 75265 TYP 25°C 0.05 0°C 0.05 70°C 0.04 25°C 0.04 0°C 0.05 70°C 0.04 25°C 68 25°C 1 0°C 1.3 70°C 0.9 25°C 110 0°C 125 70°C 90 25°C 38° 0°C 40° 70°C 34° UNIT MAX V/µs nV/√Hz kHz MHz 11 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC25M2C TLC25M2AC TLC25M2BC MIN VIO Input offset voltage VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 100 kΩ Full range TLC252AC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 100 kΩ Full range TLC252BC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 100 kΩ αVIO Average temperature coefficient of input offset voltage IIO Input offset current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V IIB Input bias current (see Note 4) VO = 2 2.5 5V V, VIC = 2 2.5 5V VICR VOH VOL AVD CMRR kSVR IDD 25°C TLC252C Low-level output voltage Large-signal L i l differential diff ti l voltage lt amplification am lification Common-mode rejection ratio VID = 100 mV, RL = 100 kΩ VID = – 100 mV, IOL = 0 VO = 0.25 V to 2 V, RL = 100 kΩ VIC = VICRmin S l lt j ti ratio ti Supply-voltage rejection (∆VDD /∆VDD) VDD = 5 V to 10 V, Supply current (two amplifiers) VO = 2 2.5 5V V, No load VO = 1.4 V VIC = 2 2.5 5V V, TYP MAX 1.1 10 12 25°C 0.9 0.22 Full range POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 2 3 µV/°C 25°C to 70°C 1.7 25°C 0.1 60 70°C 7 300 25°C 0.6 60 70°C 40 600 25°C – 0.2 to 4 Full range – 0.2 to 3.5 – 0.3 to 4.2 pA pA V V 25°C 3.2 3.9 0°C 3 3.9 70°C 3 4 V 25°C 0 50 0°C 0 50 70°C 0 50 25°C 25 170 0°C 15 200 70°C 15 140 25°C 65 91 0°C 60 91 70°C 60 92 25°C 70 93 0°C 60 92 70°C 60 94 mV V/mV dB dB 25°C 210 560 0°C 250 640 70°C 170 440 † Full range is 0°C to 70°C. NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. 12 5 6.5 25°C Common-mode input voltage g range (see Note 5) High-level output voltage UNIT µA TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLC25M2C TLC25M2AC TLC25M2BC MIN VIO Input offset voltage VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 100 kΩ Full range TLC252AC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 100 kΩ Full range TLC252BC VO = 1.4 V,, RS = 50 Ω, VIC = 0,, RL = 100 kΩ αVIO Average temperature coefficient of input offset voltage IIO Input offset current (see Note 4) VO = 5 V V, VIC = 5 V IIB Input bias current (see Note 4) VO = 5 V V, VIC = 5 V VICR VOH VOL AVD CMRR kSVR IDD 25°C TLC252C Low-level output voltage Large-signal L i l differential diff ti l voltage lt amplification am lification Common-mode rejection ratio VID = 100 mV, VID = – 100 mV, VO = 1 V to 6 V, VDD = 5 V to 10 V, Supply current (two amplifiers) VO = 5 V V, No load MAX 1.1 10 0.9 5 6.5 25°C 0.224 Full range 3 µV/°C 2.1 25°C 0.1 60 70°C 7 300 25°C 0.7 60 70°C 50 600 RL = 100 kΩ IOL = 0 RL = 100 kΩ VO = 1.4 V VIC = 5 V, V mV 2 25°C to 70°C VIC = VICRmin S l lt j ti ratio ti Supply-voltage rejection (∆VDD /∆VDD) TYP 12 25°C 25°C – 0.2 to 9 Full range – 0.2 to 8.5 Common-mode input voltage g range (see Note 5) High-level output voltage UNIT – 0.3 to 9.2 pA pA V V 25°C 8 8.7 0°C 7.8 8.7 70°C 7.8 8.7 V 25°C 0 50 0°C 0 50 70°C 0 50 25°C 25 275 0°C 15 320 70°C 15 230 25°C 65 94 0°C 60 94 70°C 60 94 25°C 70 93 0°C 60 92 70°C 60 94 mV V/mV dB dB 25°C 285 600 0°C 345 800 70°C 220 560 µA † Full range is 0°C to 70°C. NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 operating characteristics, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC25M2C TLC25M2AC TLC25M2BC MIN VI(PP) ( )=1V SR Slew rate at unity gain RL = 100 kΩ,, See Figure 1 CL = 20 pF,, VI(PP) ( ) = 2.5 V Vn BOM B1 φm Equivalent input noise voltage Maximum output-swing bandwidth Unity-gain bandwidth Phase margin f = 1 kHz, VO = VOH, See Figure VI = 10 mV, VI = 10 mV, mV See Figure 3 RS = 20 Ω, CL = 20 pF, F CL = 20 pF, f = B1, See Figure 2 RL = 100 kΩ, kΩ See Figure 3 CL = 20 pF, pF TYP 25°C 0.43 0°C 0.46 70°C 0.36 25°C 0.40 0°C 0.43 70°C 0.34 25°C 32 25°C 55 0°C 60 70°C 50 25°C 525 0°C 600 70°C 400 25°C 40° 0°C 41° 70°C 39° UNIT MAX V/µs nV/√Hz kHz MHz operating characteristics, VDD = 10 V PARAMETER TEST CONDITIONS TA TLC25M2C TLC25M2AC TLC25M2BC MIN VI(PP) ( )=1V SR Slew rate at unity gain RL = 100 kΩ,, See Figure 1 CL = 20 pF,, VI(PP) ( ) = 5.5 V Vn Equivalent input noise voltage f = 1 kHz, RS = 20 Ω, See Figure 2 BOM Maximum output-swing bandwidth VO = VOH, See Figure 1 CL = 20 pF, F RL = 100 kΩ, kΩ B1 φm 14 Unity-gain bandwidth Phase margin VI = 10 mV, mV VI = 10 mV, See Figure 3 CL = 20 pF, f = B1, POST OFFICE BOX 655303 See Figure 3 pF CL = 20 pF, • DALLAS, TEXAS 75265 TYP 25°C 0.62 0°C 0.67 70°C 0.51 25°C 0.56 0°C 0.61 70°C 0.46 25°C 32 25°C 35 0°C 40 70°C 30 25°C 635 0°C 710 70°C 510 25°C 43° 0°C 44° 70°C 42° UNIT MAX V/µs nV/√Hz kHz MHz TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 electrical characteristics, VDD = 5 V, TA = 25°C PARAMETER TEST CONDITIONS VO = 1.4 V, RS = 50 Ω, TLC252Y MIN VIC = 0 V, See Note 6 TLC25L2Y TYP MAX 1.1 10 MIN TLC25M2Y TYP MAX 1.1 10 MIN TYP MAX 1.1 10 UNIT VIO Input offset voltage αVIO Average temperature coefficient of input offset voltage IIO Input offset current (see Note 4) VO = VDD/2, VIC = VDD/2 0.1 60 0.1 60 0.1 60 pA IIB Input bias current (see Note 4) VO = VDD/2, VIC = VDD/2 0.6 60 0.6 60 0.6 60 pA VICR Common-mode input voltage range (see Note 5) VOH High-level output voltage VID = 100 mV, See Note 6 VOL Low-level output voltage VID = – 100 mV, IOL = 0 AVD Large-signal differential voltage amplification VO = 0.25 V, See Note 6 CMRR Common-mode rejection ratio kSVR IDD 1.8 1.1 mV µV/°C 1.7 – 0.2 to 4 – 0.3 to 4.2 – 0.2 to 4 – 0.3 to 4.2 – 0.2 to 4 – 0.3 to 4.2 V 3.2 3.8 3.2 4.1 3.2 3.9 V 0 50 0 50 0 50 mV 5 23 50 700 25 170 V/mV VIC = VICRmin 65 80 65 94 65 91 dB Supply-voltage rejection ratio (∆VDD /∆VIO) VDD = 5 V to 10 V, VO = 1.4 V 65 95 70 97 70 93 dB Supply current VO = VDD/2, VIC = VDD/2, No load 1.4 3.2 0.02 0.034 0.21 0.56 mA operating characteristics, VDD = 5 V, TA = 25°C PARAMETER TEST CONDITIONS TLC252Y MIN TYP TLC25L2Y MAX MIN TYP TLC25M2Y MAX MIN TYP MAX UNIT Slew rate at unity gain CL = 20 pF,, See Note 6 VI(PP) = 1 V VI(PP) = 2.5 V 3.6 0.03 0.43 2.9 0.03 0.40 Vn Equivalent input noise voltage f = 1 kHz, RS = 20 Ω 2.5 68 32 nV√/Hz BOM Maximum outputswing bandwidth VO = VOH, RL = 10 kΩ CL = 20 pF, 320 5 55 kHz B1 Unity-gain bandwidth VI = 10 mV, CL = 20 pF 1.7 0.085 0.525 MHz φm Phase margin f = B1, CL = 20 pF VI = 10 mV, 46° 34° 40° V/µs NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually. 6. For low-bias mode, RL = 1 MΩ; for medium-bias mode, RL = 100 kΩ, and for high-bias mode, RL = 10 kΩ. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 PARAMETER MEASUREMENT INFORMATION single-supply versus split-supply test circuits Because the TLC252, TLC25L2, and TLC25M2 are optimized for single-supply operation, circuit configurations used for the various tests often present some inconvenience since the input signal, in many cases, must be offset from ground. This inconvenience can be avoided by testing the device with split supplies and the output load tied to the negative rail. A comparison of single-supply versus split-supply test circuits is shown below. The use of either circuit gives the same result. VDD + VDD – – VO VI + CL VO VI + CL RL RL VDD – (a) SINGLE SUPPLY (b) SPLIT SUPPLY Figure 1. Unity-Gain Amplifier 2 kΩ 2 kΩ VDD VDD 20 Ω – – VO 1/2 VDD VO + + 20 Ω 20 Ω 20 Ω VDD– (a) SPLIT SUPPLY (a) SINGLE SUPPLY Figure 2. Noise-Test Circuit 10 kΩ 10 kΩ VDD+ VDD 100 Ω VI VI 100 Ω VO + VO 1/2 VDD – – CL + CL VDD– (a) SINGLE SUPPLY (a) SPLIT SUPPLY Figure 3. Gain-of-100 Inverting Amplifier 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 TYPICAL CHARACTERISTICS Table of Graphs FIGURE IDD Supply current AVD Large-signal differential voltage amplification Phase shift vs Supplyy voltage g vs Free-air temperature 4 5 Low bias vs Frequency 6 Medium bias vs Frequency 7 High bias vs Frequency 8 Low bias vs Frequency 6 Medium bias vs Frequency 7 High bias vs Frequency 8 SUPPLY CURRENT vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE 10000 10000 High-Bias Versions 1000 Medium-Bias Versions 100 Low-Bias Versions 10 1000 Medium-Bias Versions 100 Low-Bias Versions 10 0 0 0 2 4 6 8 VDD = 10 V VIC = 0 V VO = 2 V No Load High-Bias Versions I DD – Supply Current – µ A I DD – Supply Current – µ A VO = VIC = 0.2 VDD No Load TA = 25°C 10 12 14 16 18 20 0 10 20 30 40 50 60 70 80 TA – Free-Air Temperature – °C VDD – Supply Voltage – V Figure 4 Figure 5 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 TYPICAL CHARACTERISTICS LOW-BIAS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY VDD = 10 V RL = 1 MΩ TA = 25°C 106 105 30° AVD (left scale) 104 60° 103 90° Phase Shift (right scale) 102 ÁÁ ÁÁ ÁÁ 0° 120° 101 150° 1 180° Phase Shift AVD AVD – Low-Bias Large-Signal Differential Voltage Amplification 107 0.1 0.1 1 10 100 1k 10 k 100 k Frequency – Hz Figure 6 MEDIUM-BIAS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY ÁÁ ÁÁ VDD = 10 V RL = 100 kΩ TA = 25°C 106 105 30° AVD (left scale) 104 60° 103 90° Phase Shift (right scale) 102 120° 101 150° 1 180° 0.1 1 10 100 1k 10 k 100 k Frequency – Hz Figure 7 18 0° POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1M Phase Shift AVD A VD – Medium-Bias Large-Signal Differential Voltage Amplification 107 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 TYPICAL CHARACTERISTICS HIGH-BIAS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY ÁÁ ÁÁ VDD = 10 V RL = 10 kΩ TA = 25°C 106 105 0° 30° 104 60° Phase Shift (right scale) 103 90° 102 120° Phase Shift AVD AVD – High-Bias Large-Signal Differential Voltage Amplification 107 AVD (left scale) 101 150° 1 180° 0.1 10 100 1k 10 k 100 k 1M 10 M Frequency – Hz Figure 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19 TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS SLOS002I – JUNE 1983 – REVISED MARCH 2001 APPLICATION INFORMATION latch-up avoidance Junction-isolated CMOS circuits have an inherent parasitic PNPN structure that can function as an SCR. Under certain conditions, this SCR may be triggered into a low-impedance state, resulting in excessive supply current. To avoid such conditions, no voltage greater than 0.3 V beyond the supply rails should be applied to any pin. In general, the operational amplifier supplies should be applied simultaneously with, or before, application of any input signals. output stage considerations The amplifier’s output stage consists of a source-follower-connected pullup transistor and an open-drain pulldown transistor. The high-level output voltage (VOH) is virtually independent of the IDD selection and increases with higher values of VDD and reduced output loading. The low-level output voltage (VOL) decreases with reduced output current and higher input common-mode voltage. With no load, VOL is essentially equal to the potential of VDD – /GND. supply configurations Even though the TLC252 / 25_2C series is characterized for single-supply operation, it can be used effectively in a split-supply configuration if the input common-mode voltage (VICR), output swing (VOL and VOH), and supply voltage limits are not exceeded. circuit layout precautions The user is cautioned that whenever extremely high circuit impedances are used, care must be exercised in layout, construction, board cleanliness, and supply filtering to avoid hum and noise pickup, as well as excessive dc leakages. 20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TLC252ACD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 252AC TLC252BCP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 TLC252BCP TLC252CD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 252C TLC252CDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 252C TLC252CP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 TLC252CP TLC252CPE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 TLC252CP TLC252CPWR ACTIVE TSSOP PW 8 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 P252 TLC25L2ACD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 25L2AC TLC25L2BCP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 TLC25L2BC TLC25L2CD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 25L2C TLC25L2CDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM TLC25L2CP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLC25M2ACD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 25M2AC TLC25M2ACP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 TLC25M2AC TLC25M2CD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 25M2C TLC25M2CDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 25M2C TLC25M2CP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 TLC25M2CP (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. Addendum-Page 1 25L2C TLC25L2CP Samples PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2022 OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of