User's Guide
SLVUAE6A – January 2015 – Revised July 2015
TLC6C5712-Q1 Evaluation Module
1
Introduction
This document is the user's guide for the TLC6C5712-Q1 evaluation module (EVM) as a supplement to
the TLC6C5712-Q1 data sheet. This user’s guide describes the characteristics, operation, and use of the
TLC6C5712-Q1 EVM. This EVM is designed to help the user evaluate and test the various operating
modes of the TLC6C5712-Q1 device. This user’s guide includes a detailed description of the graphical
user interface (GUI) which can help customers easily use the GUI. The guide also contains the setup
instructions for the hardware and software, a schematic diagram, a bill of materials (BOM), and PCB
layout drawings for the evaluation module.
The TLC6C5712-Q1 device is a 12 channel, constant-current LED driver that is capable of driving up to 75
mA per channel. The device contains an integrated DOT-correction circuitry which can adjust the DC
current for each output channel to compensate for a difference in brightness among the LEDs. The device
also has integrated PWM mapping control to provide individual LED PWM dimming. The device has full
LED diagnostics, such as LED open, LED short, output short to GND, over-temperature prewarning, overtemperature thermal shutdown, reference short and open, adjacent pin short, and others. This EVM can
be used to evaluate a single device, but it can be also configured to drive two devices in a cascade
configuration. By using the GUI, users can easily evaluate the device.
Figure 1. Top View of the TLC6C5712-Q1EVM PCB
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
1
Requirements
2
www.ti.com
Requirements
To operate this EVM, the software, power supply, and communication board must be connected and
properly configured. This section provides more information on each component.
2.1
Software
Texas Instruments has provided the necessary software to evaluate this EVM. For the latest software
revision, go to the TLC6C5712-Q1 product folder, www.ti.com/product/TLC6C5712-Q1,.
2.2
Power Supply Requirements
The EVM board can receive supply in one of two ways. The first way is suitable for evaluation in the lab
which uses two DC power supplies. The first DC power supply is for VCC and the other is for VSENSE.
The second way is suitable for portable demonstration. In this case, only a 5-V micro-USB supply is
required. The VSENSE pin can be powered through a USB cable directly and the VCC pin can be directly
supplied by the USB2ANY.
2.3
Communication Board
The USB2ANY is the interface between the PC and the TLC6C5712-Q1EVM. One end of the USB2ANY
connects to the PC with the USB cable and the other end of the USB2ANY connects to the EVM with the
ribbon cable. After installing the GUI, users can control the TLC6C5712-Q1EVM by sending commands
through the USB2ANY.
3
Setup
The following sections describe how to setup the EVM hardware and software.
3.1
Hardware Setup
Figure 2 shows the hardware setup of the TLC6C5712-Q1EVM.
Step 1. Connect the 5-V power supply to the LED board between TP1 (VSENSE) and TP3 (GND).
Users can also use the 5-V micro-USB supply connected to J2 to supply VSENSE.
Step 2. Put a shunt on J3 to connect the USB2ANY 3.3-V supply to VCC. In this case, the user is not
required to supply VCC with another DC supply.
Step 3. Connect the host computer to USB2ANY board using the USB cable.
Step 4. Connect the ribbon cable between the USB2ANY board and the TLC6C5712-Q1 EVM board.
5V
DC Supply
VSENSE
USB
cable
USB2ANY
Put Shunt on J3 to
VCC
supply VCC from
GND
USB2ANY
TLC6C5712-Q1EVM
Ribbon Cable
Figure 2. Hardware Setup for TLC6C5712-Q1EVM
2
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
3.2
Software Installation
Download the GUI software from www.ti.com. After downloading, install the TLC6C5712-Q1 EVM GUI on
the PC. A shortcut to the GUI is found on the desktop. A shortcut can also be found in the startup menu
under the Texas Instruments folder.
3.3
GUI Connection
After setting up the hardware, open the GUI. Figure 3 shows the overview of the TLC6C5712-Q1 EVM
GUI. When the EVM is connected correctly, the status bar at the bottom right of the GUI will show a green
CONNECTED status. A red SIMULATION status indicates that the device is not connected. Check the
connection of the device to make sure that it is properly connected. If the SIMULATION status still
appears, then uncheck the Simulate Communication box in the top right of the GUI to connect the device.
Figure 3. TLC6C5712-Q1 EVM GUI Overview
4
Input and Output Connector Descriptions
4.1
Power Supply Connector
Table 1 list the connector descriptions of the power supply.
Table 1. Power Supply Connectors
CONNECTOR
NAME
DESCRIPTION
TP1
VSENSE
This connector is the positive input of the load supply
J2
VSENSE Supply
The connector is a Micro-USB connector, it can be used to supply the load by an
USB cable.
TP2
VCC
This connector is the positive input of the IC internal supply.
TP3
GND
This connector is the ground of the EVM.
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
3
Input and Output Connector Descriptions
4.2
www.ti.com
SPI Interface Connectors
The J1 jumper is the SPI interface connector. Table 2 lists the detailed description of J1.
Table 2. SPI Interface Connector
4
PIN NO.
PIN SYMBOL
SIGNAL NAME
I/O
FUNCTION
1
—
—
—
—
2
—
—
—
—
3
—
—
—
—
4
PWM3
PWM3
Input
PWM input for PWM3 of U1
5
PWM2
PWM2
Input
PWM input for PWM2 of U1
6
PWM4
PWM4
Input
PWM input for PWM4 of U1
7
—
—
—
—
8
PWM5
PWM5
Input
PWM input for PWM5 of U1
9
—
—
—
—
10
—
—
—
—
11
PWM0
PWM0
Input
PWM input for PWM0 of U1
12
LATCH_IN
Serial data latch
Input
Rising edge latches data from
shift registers into the device
13
SDO_OUT
Serial data output
Output
Serial data output for U1. This is
also the serial data input in
cascade mode.
14
SDI_IN
Serial data input
Input
Serial data input for U1
15
3.3 V
3.3-V supply
Power
3.3-V supply on USB2ANY
16
GND
Ground
Power
Signal ground
17
PWM1
PWM1
Input
PWM input for PWM1 of U1
18
SCLK_IN
Serial data clock
Input
Serial data input clock
19
—
—
—
—
20
ERR
Error output
Output
Error output for device
21
—
—
—
—
22
—
—
—
—
23
—
—
—
—
24
—
—
—
—
25
—
—
—
—
26
—
—
—
—
27
—
—
—
—
28
—
—
—
—
29
—
—
—
—
30
—
—
—
—
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Input and Output Connector Descriptions
www.ti.com
4.3
Test Points
Table 3 the test points of the EVM.
Table 3. Test points of the EVM
SYMBOL
NAME
FUNCTION
TP15
SCLK_IN
SPI clock input of U1
TP13
SDI_IN
SPI data input of U1
TP12
LATCH_IN
SPI latch input of U1
TP14
SDO
SPI data output of U1
TP29
ERR
ERR output of U1
TP16
OUT0
OUT0 of U1
TP17
OUT1
OUT0 of U1
TP18
OUT2
OUT0 of U1
TP19
OUT3
OUT0 of U1
TP20
OUT4
OUT0 of U1
TP21
OUT5
OUT0 of U1
TP5
PWM0
PWM0 of U1
TP6
PWM1
PWM0 of U1
TP7
PWM2
PWM0 of U1
TP4
VCC
VCC of U1
TP11
IREF
Iref of U1
TP30
GND
GND
TP28
VSENSE
VSENSE of U1
TP27
OUT11
OUT0 of U1
TP26
OUT10
OUT0 of U1
TP25
OUT9
OUT0 of U1
TP24
OUT8
OUT0 of U1
TP23
OUT7
OUT0 of U1
TP22
OUT6
OUT0 of U1
TP10
PWM5
PWM0 of U1
TP9
PWM4
PWM0 of U1
TP8
PWM3
PWM0 of U1
J21, J22, J23, J24, J25, J26, J27, J28,
J29, J30, J31, J32
VSENSE
VSENSE of U1
J34, J35, J36, J37, J38, J39, J40, J41,
J42, J43, J44, J45
GND
GND
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
5
Input and Output Connector Descriptions
4.4
www.ti.com
Jumpers
Table 4 lists shows the jumpers of the EVM.
Table 4. Jumpers of the EVM
6
JUMPER
DESCRIPTION
J3
Connect 3.3 V to VCC
J17
Connect REF resister and GND
J16
Connect SDO to SDO_OUT, when controlling a single TLC6C5712-Q1 device, put a shunt on this jumper
J18
Cascade U1 with U2, when controlling U1 and U2 in series, remove shunt on J16, put shunt on J18 and J19
J19
Cascade U1 with U2, when controlling U1 and U2 in series, remove shunt on J16, put shunt on J18 and J19
J20
OUT0-5 of U2
J33
OUT6-11 of U2
J4
Connect D1 to OUT0 of U1
J5
Connect D2 to OUT1 of U1
J6
Connect D3 to OUT2 of U1
J7
Connect D4 to OUT3 of U1
J8
Connect D5 to OUT4 of U1
J9
Connect D6 to OUT5 of U1
J10
Connect D7 to OUT6 of U1
J11
Connect D8 to OUT7 of U1
J12
Connect D9 to OUT8 of U1
J13
Connect D10 to OUT9 of U1
J14
Connect D11 to OU10 of U1
J15
Connect D12 to OUT11 of U1
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
GUI Function
www.ti.com
5
GUI Function
This section describes the details of the TLC6C5712-Q1 EVM GUI. The GUI has two configuration levels:
one is a high-level configuration, the other is a low-level configuration. In the high-level configuration, two
tabs are included which are for the general function and advanced function. Low-level configuration
describes all the TLC6C5712-Q1 registers. The following sections introduce the details of the functions.
5.1
General
Figure 4 shows the general tab of TLC6C5712-Q1 EVM GUI. In this page, users can easily change the
register values.
Figure 4. TLC6C5712-Q1 EVM GUI
The general tab is divided into four parts. Figure 5 shows the register control of CH ON MASK, PWM MAP
MASK, SHORT GND MASK, LED SHORT MASK, OPEN FAULT MASK, and DOT CORRECTION
SETTING.
The LEDs can be turned on by clicking the CH ON MASK button. The word on the button shows the value
sent to the register. When the button displays OFF, the value of the CH ON MASK is 1 which means the
LED is masked and the output is turned off. When the button displays ON, the value of the CH ON MASK
is 0 which means the LED is not masked and the output is turned on.
The PWM MAP MASK is used to map the PWM control for each channel. When driving the EVM using the
USB2ANY board, only three PWM outputs available: PWM0, PWM1, and PWM2. These outputs can be
controlled by the sliders in Figure 6. The PWM3, PWM4 and PWM5 are connected to the GND of
USB2ANY.
The SHORT GND MASK, LED SHORT MASK, and OPEN FAULT MASK are used to control the fault
mask. A setting of 1 indicates that the fault is masked. A setting of 0 indicates that the fault is not masked.
When the fault is unmasked, the fault will be reported to the open and short registers in the status register.
SHORT GND MASK and LED SHORT MASK correspond with the status of the short register shown in
Figure 7. OPEN FAULT MASK corresponds with the status of the open register shown in Figure 7.
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
7
GUI Function
www.ti.com
The DOT CORRECTION SETTING is used for setting the output current for each channel. Each channel
has an internal 8-bit linear current DAC for individual dot correction control. Use Equation 1 to set the
output current.
VREF u K OUT DC 1
IOUT
u
RREF
256
where
•
•
•
•
VREF is the reference voltage, 1.229 V
KOUT is the output current to IREF current ratio, 500
RREF is the reference resistor
DC is the DOT correction setting value
(1)
Figure 5. General Function I
PWM FAULT MASK is used to control the PWM fault mask. A setting of 1 indicates that the PWM fault is
masked and therefore the fault will not be reported to the status register shown in Figure 7. A setting of 0
indicates that the PWM fault is unmasked and therefore when a PWM fault occurs, the fault will be
reported to PWM status register.
The ERR MASK field is used to control the ERROR mask. A setting of 1 indicates that the error is masked
and therefore the error is not reported to the ERROR indicator shown in Figure 8. A setting of 0 indicates
that the error is unmasked and therefore, when an error occurs, the error is reported to the ERROR
indicator. When users need the error indicator to report the fault, the fault mask for each channel (such as
PWM fault mask, SHORT GND MASK, and so on) should not be masked. When D13 on the EVM is on,
users can click the READ ALL to get the fault.
The MISC_CMD field contains fives commands. The D_OFD command disables the off state diagnostic. If
the LED off-state diagnostic is not needed, change the register value to 1. The ADJ_SH command detects
the adjacent pin short fault. Users can implement the detection by setting the register value to 1. Because
the register value resets to 0 after the device finishes the detection, users must change the ADJ_SH value
back to 0 after the detection is complete. The S_SR command is used to control the output slew rate. A
setting of 1 indicates the slow slew rate. The F_ERR command forces the ERROR output state. When the
register is 1, the ERR output is pulled low even the system has no error. The WLS command configures
the weak-load supply-detection threshold. A setting of 1 indicates that the detection threshold is 2.77 V. A
setting of 0 indicates that the detection threshold is 4.2 V.
8
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
GUI Function
www.ti.com
The PWM0, PWM1, and PWM2 fields generate the PWM control signals for the TLC6C5712-Q1 EVM.
PWM0, PWM1, and PWM2 corresponds with the PWM0, PWM1, and PWM2 inputs of the TLC6C5712-Q1
device. Users can select from the following 8 frequencies: 100 Hz, 200 Hz, 500 Hz, 1 KHz, 2 KHz, 5 KHz,
10 KHz, 20 KHz, 50 KHz, and 100 KHz. The duty cycles can also be changed from 0 to 100%
respectively.
Figure 6. General Function II
Figure 7 shows the status registers and fault registers of the TLC6C5712-Q1 device. By clicking the Read
All button, the information of these registers is read out. A red indicator color indicates a fault.
Figure 7. General Function III
Figure 8 contains registers with simple read and write functions. Users can write and read registers by
input address and data value. The ERROR indicator shows the ERR pin state. If the error pin is pulled
low, the ERROR indicator displays red. The left side of Figure 8 shows several special commands of
TLC6C5712-Q1 device which can be found in the datasheet (SLVSCO9).
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
9
GUI Function
www.ti.com
Figure 8. General Function IV
5.2
Advanced Commands
Figure 9 shows the advanced command functions. Users can write command sequences in the Codes to
Send field. Users must follow the specific format when inputting the commands. The standard format for
comments is // comments which is optional. The GUI identifies the // symbol and ignores the content
following this symbol. The text following the symbol can be in either uppercase or lowercase. The delay
function is only used for general delay as the delay time does not contain the software operate delay.
Address Data // comments
0x61 0x69 // power on reset
0x62 0x66
PWM(1,2,50) //PWM(Channel,Index,DutyCycle)
Delay 100 // Delay N, delay N ms
0x52 0x00 //Turn on CH0-CH5
0x53 0x00 //Turn on CH6-CH11
0x46 0xff
//CH0 Dot Correction value = 255
.........
For the PWM command, the channel value should range from 0 to 2. A value of 0 corresponds with
PWM0, a value of 1 corresponds with PWM1, and a value of 2 corresponds with PWM2. The index value
should range from 0 to 9. This value corresponds with a frequency from 100 Hz to 100 kHz. Table 5 lists
the relationship between the channel and PWM control. Table 6 lists the relationship between the index
value and frequency.
Table 5. Channel and PWM Control
CHANNEL
0
1
2
PWM CONTROL
PWM0
PWM1
PWM2
Table 6. Index and Frequency
10
INDEX
0
1
2
3
4
5
6
7
8
9
FREQUENCY
100 Hz
200 Hz
500 Hz
1 kHz
2 kHz
5 kHz
10 kHz
20 kHz
50 kHz
100 kHz
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
GUI Function
www.ti.com
The GUI can distinguish read commands from write commands. When the command is a read command,
the read-back data is displayed in the Codes Received field.
Selecting the Loop the Codes box sends the codes repeatedly. The Binary to Hex to Hexadecimal to
Decimal Converter can help users easily convert the data scale.
Figure 9. Advanced Commands
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
11
GUI Function
5.3
www.ti.com
Register Map
In the low-level configuration, users can change the register bits by directly clicking the bit value. If the
immediate update mode is selected, the register value is updated immediately when the value is changed.
If manual update mode is selected, the register value is not updated unless the Write Selected or Write
Modified button is clicked.
Figure 10. Register Map
Users can save the register configuration by clicking the Saving Configuration button. When opening the
configuration file, all of the saved registers value are reloaded into the device.
12
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Bill of Materials and Schematic
www.ti.com
6
Bill of Materials and Schematic
Table 7 lists the bill of materials (BOM) for the TLC6C5712EVM.
Table 7. TLC6C5712-Q1 BOM
DESIGNATOR
QUANTITY
VALUE
DESCRIPTION
PARTNUMBER
MANUFACTURER
C1, C5
2
4.7 µF
Capacitor, ceramic 4.7 µF, 16 V, ±10%, X5R, 0805
GRM21BR61C475KA88L
MuRata
C2, C6
2
0.1 µF
Capacitor, ceramic 0.1 µF, 16 V, ±5%, X7R, 0603
0603YC104JAT2A
AVX
C3, C7, C9, C10
4
4.7 µF
Capacitor, ceramic 4.7 µF, 16 V, ±10%, X5R, 0805
EMK212BJ475KG-T
Taiyo Yuden
C8
1
10 µF
Capacitor, ceramic 10 µF, 16 V, ±10%, X6S, 0805
C2012X6S1C106MT
TDK
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12
12
White
LED, White, SMD
LW-E6SG
OSRAM
D13, D26
2
Red
LED, Red, SMD
LTST-C170KRKT
Lite-On
D14, D17, D20, D23
4
Red
LED, Red, SMD
LR-E6SF
OSRAM
D15, D18, D21, D24
4
Green
LED, Green, SMD
LT-E6SG
OSRAM
D16, D19, D22, D25
4
Blue
LED, Blue, SMD
LB-E6SG
OSRAM
J1
1
Connector, 15x2, 3A 300V STRT DIP, TH
XG4C-3031
Omron Electronic
Components
J2
1
Receptacle, 0.65 mm, 5x1, Gold, R/A, SMT
10118192-0001LF
FCI
J3, J4, J5, J6, J7, J8, J9, J10, J11, J12, J13, J14,
J15, J16, J17
15
Header, 100mil, 2x1, Gold, TH
TSW-102-07-G-S
Samtec
J18
1
Header, 100mil, 8x2, Gold, TH
TSW-108-07-G-D
Samtec
J19
1
Header, 100mil, 5x2, Gold, TH
TSW-105-07-G-D
Samtec
J20, J33
2
Header, 100mil, 6x1, Gold, TH
TSW-106-07-G-S
Samtec
J21, J22, J23, J24, J25, J26, J27, J28, J29, J30,
J31, J32, J34, J35, J36, J37, J38, J39, J40, J41,
J42, J43, J44, J45
24
Header, 100mil, 1pos, Gold, TH
TSW-101-07-G-S
Samtec
R1, R4
2
12.1 kΩ
Resistor, 12.1 kΩ, 1%, 0.1 W, 0603
CRCW060312K1FKEA
Vishay-Dale
R2, R5
2
1 kΩ
Resistor, 1 kΩ, 5%, 0.1 W, 0603
CRCW06031K00JNEA
Vishay-Dale
R3, R6
2
3.3 kΩ
Resistor,, 3.3 kΩ, 5%, 0.1 W, 0603
CRCW06033K30JNEA
Vishay-Dale
R7, R8
2
0
Resistor, 0, 5%, 0.1 W, 0603
ERJ-3GEY0R00V
Panasonic
SH-J1, SH-J2, SH-J3, SH-J4, SH-J5, SH-J6, SH-J7,
SH-J8, SH-J9, SH-J10, SH-J11, SH-J12, SH-J13,
SH-J14, SH-J15
15
1x2
Shunt, 100mil, Gold plated, Black
969102-0000-DA
3M
TP1, TP2, TP3
3
Double
Terminal, Turret, TH, Double
1502-2
Keystone
TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12,
TP13, TP14, TP15, TP16, TP17, TP18, TP19, TP20,
TP21, TP22, TP23, TP24, TP25, TP26, TP27, TP28,
TP29, TP30
27
White
Test Point, Miniature, White, TH
5002
Keystone
U1
1
Constant Current Sink LED Driver, PWP0028H
TLC6C5712QPWPRQ1
Texas Instruments
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
TLC6C5712-Q1 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
13
Bill of Materials and Schematic
www.ti.com
VSENSE
SH-J4
J7
SH-J6
J9
SH-J8
J10
SH-J9
J11
SH-J10
J12
D11
SH-J12
J14
SH-J11
J13
4
4
D10
White
White
D12
2
White
2
White
4
4
D9
D8
White
2
2
2
2
SH-J5
J8
White
2
D7
D6
White
2
D5
4
4
4
4
4
4
SH-J3
J6
2
2
SH-J2
J5
SH-J7
J4
D4
White
1
2
MP1
MP2
MP3
MP4
MP5
MP6
D3
White
1
2
MP1
MP2
MP3
MP4
MP5
MP6
D2
White
2
4
D1
White
1
2
White
SH-J13
J15
C10
4.7µF
1
2
C9
4.7µF
1
2
C4
NC
1
2
1
2
Use Micro-USB cable on J2 to Power the LED
1
2
10118192-0001LF
1
2
1
2
SH-J1
VCC
Put Shunt on J3 to Connect
3.3V Supply to VCC
LATCH_IN
SDI_IN
GND
SCLK_IN
ERR
1
2
GND
PWM3
PWM4
PWM5
2
J3
1
2
VCC
TP3
VSENSE 1
2
3
4
5
GND
1
2
VSENSE
VCC 3V - 5.5V
TP2
VSENSEmax 7V
TP1
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
4
J2
J1
1
3
PWM2 5
7
9
PWM0 11
13
SDO_OUT
3.3V 15
PWM1 17
19
21
23
25
27
29
XG4C-3031
Headers
U1
SDO
1
2
J16
C1
4.7µF
SH-J14
SDO_OUT
Remove the shunts for series connect, put
shunt on J42 for indenpendent U1 control.
C2
0.1µF
GND
Singal Device
J18
2
4
6
8
10
12
14
16
SCLK_IN_2
SDI_2
LATCH_2
SDO_2
ERR_2
PWM0_2
PWM1_2
PWM2_2
SH-J15
TSW-108-07-G-D
27
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
12
13
14
15
16
17
IREF
26
R1
LATCH_IN 3
12.1k
J17
2
SDI_IN
4
SDO
SCLK_IN 1
1
2
SCLK_IN 1
3
SDO
LATCH_IN 5
SDO_OUT 7
9
ERR
11
PWM0
13
PWM1
15
PWM2
VCC
VCC
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
IREF
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
OUT9
OUT10
OUT11
VSENSE
LATCH
ERR
SDI
SDO
SCK
PGND
GND
GND
PAD
6
7
8
9
10
11
18
19
20
21
22
23
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
OUT9
OUT10
OUT11
R7
24
D13
5
ERR
2
R2
1
C3
4.7µF
VCC
1.0k
25
VSENSE
0
Red
28
R3
29
3.3k
GND
TLC6C5712QPWPRQ1
J19
1
VCC_2
VSENSE_23
PWM5_2 5
PWM4_2 7
PWM3_2 9
2
4
6
8
10
VCC
VSENSE
PWM5
PWM4
PWM3
GND
TSW-105-07-G-D
Cascade With Two Devices
D14
Red
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
IREF
LATCH_IN
SDI_IN
SDO
SCLK_IN
VCC_2
C5
4.7µF
TP16
TP17
TP18
TP19
TP20
TP21
TP22
TP23
TP24
TP25
TP26
TP27
TP28
TP29
TP30
GND
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
OUT9
OUT10
OUT11
J21
J22
J23
J24
J25
J26
J27
J28
J29
J30
J31
J32
VSENSE ERR
GND
27
C6
0.1µF PWM0_2
PWM1_2
PWM2_2
PWM3_2
PWM4_2
PWM5_2
IREF_2
6
5
4
3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
J20
OUT0_2
OUT1_2
OUT2_2
OUT3_2
OUT4_2
OUT5_2
VSENSE
6
5
4
3
2
1
J45
1
J44
1
J43
1
J42
1
J41
1
J40
1
J39
1
J38
1
J37
1
J36
1
1
1
J35
OUT6_2
OUT7_2
OUT8_2
OUT9_2
OUT10_2
OUT11_2
26
LATCH_2 3
VCC
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
IREF
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
OUT9
OUT10
OUT11
VSENSE
LATCH
ERR
GND
J33
J34
R4
12.1k
12
13
14
15
16
17
2
SDI_2
4
SDO_2
SCLK_IN_21
SDI
SDO
SCK
Green
PGND
GND
PAD
6
7
8
9
10
11
18
19
20
21
22
23
2
2
U2
VCC
D15
D18
D19
D20
D22
D21
4
4
4
4
4
4
4
4
4
D17
D16
D23
D25
D24
TP15
Blue
Red
R8
D26
ERR_2
2
1
R5
1.0k
25
28
Blue
Red
Green
Blue
Red
Green
Blue
OUT0_2
OUT1_2
OUT2_2
OUT3_2
OUT4_2
OUT5_2
OUT6_2
OUT7_2
OUT8_2
OUT9_2
OUT10_2
OUT11_2
24
5
Green
2
TP14
2
TP13
2
TP12
2
TP11
2
TP10
2
TP9
2
TP8
2
TP7
2
TP6
2
TP5
TP4
4
4
4
VSENSE_2
VCC_2
C7
4.7µF
0
VSENSE_2
C8
10µF
Red
R6
GND
3.3k
29
GND
TLC6C5712QPWPRQ1
GND
GND
Figure 11. TLC6C5712EVM Schematic
14
TLC6C5712-Q1 Evaluation Module
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Revision History
www.ti.com
Revision History
Changes from Original (January 2015) to A Revision .................................................................................................... Page
•
•
Changed the communication board from a LaunchPad to USB2ANY and updated connectors and layout .................. 1
Added additional capacitors to VSENSE in the schematic ......................................................................... 14
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
SLVUAE6A – January 2015 – Revised July 2015
Submit Documentation Feedback
Revision History
Copyright © 2015, Texas Instruments Incorporated
15
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
