Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
TMP451 ±1°C Remote and Local Temperature Sensor With η-Factor and Offset Correction,
Series-Resistance Cancellation, and Programmable Digital Filter
1 Features
3 Description
•
The TMP451 device is a high-accuracy, low-power
remote temperature sensor monitor with a built-in
local temperature sensor. The remote temperature
sensors are typically low-cost discrete NPN or PNP
transistors, or substrate thermal transistors or diodes
that are integral parts of microprocessors,
microcontrollers, or FPGAs. The temperature is
represented as a 12-bit digital code for both the local
and remote sensors, giving a resolution of 0.0625°C.
The temperature accuracy is ±1°C (maximum) in the
typical operating range for the local and the remote
temperature sensors. The two-wire serial interface
accepts the SMBus communication protocol.
1
•
•
•
•
•
•
•
•
•
±1°C Accuracy for Local and Remote Diode
Sensors
0.0625°C Resolution for Local and Remote
Channels
1.7-V to 3.6-V Supply and Logic Voltage Range
27-µA Operating Current, 3-µA Shutdown Current
Series Resistance Cancellation
η-Factor and Offset Correction
Programmable Digital Filter
Diode Fault Detection
Two-Wire and SMBus™ Serial Interface
8-Lead WSON (WDFN) Package
Advanced features such as series resistance
cancellation, programmable nonideality factor (ηfactor),
programmable
offset,
programmable
temperature limits, and a programmable digital filter
are combined to provide a robust thermal monitoring
solution with improved accuracy and noise immunity.
2 Applications
•
•
•
•
Processor and FPGA Temperature Monitoring
Smart Phones and Tablets
Servers, Desktops, and Notebooks
Telecom Equipment and Storage Area Networks
(SANs)
The TMP451 device is ideal for high-accuracy
temperature measurements in multiple locations and
in a variety of automotive subsystems. The device is
specified for operation over a supply voltage range of
1.7 V to 3.6 V and a temperature range of –40°C to
125°C.
Device Information(1)
PART NUMBER
TMP451
PACKAGE
WSON (8)
BODY SIZE (NOM)
2.00 mm × 2.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
1.7 V to 3.6 V
1.7 V to 3.6 V
1
Processor or
ASIC
V+
2
8
SCL
D+
Built-in Thermal
Transistor/Diode
3
7
D
SDA
TMP451
SMBus
Controller
4
THERM
5
GND
ALERT / THERM2
6
Overtemperature Shutdown
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
6.6
6.7
3
3
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Timing Requirements ...............................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
7.1 Overview ................................................................... 8
7.2 Functional Block Diagram ......................................... 8
7.3
7.4
7.5
7.6
8
Feature Description................................................... 8
Device Functional Modes........................................ 12
Programming........................................................... 12
Register Map........................................................... 16
Application and Implementation ........................ 29
8.1 Application Information............................................ 29
8.2 Typical Application ................................................. 29
9 Power Supply Recommendations...................... 32
10 Layout................................................................... 32
10.1 Layout Guidelines ................................................. 32
10.2 Layout Example .................................................... 33
11 Device and Documentation Support ................. 34
11.1 Trademarks ........................................................... 34
11.2 Electrostatic Discharge Caution ............................ 34
11.3 Glossary ................................................................ 34
12 Mechanical, Packaging, and Orderable
Information ........................................................... 34
4 Revision History
Changes from Original (June 2013) to Revision A
•
2
Page
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section ................................................................................................. 3
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
5 Pin Configuration and Functions
DQF Package
8-Pin WSON
Top View
V+
1
8
SCL
D+
2
7
SDA
D-
3
6
ALERT/THERM2
THERM
4
5
GND
Pin Functions
PIN
NAME
TYPE
NO.
DESCRIPTION
ALERT/THERM2
6
Digital output
Interrupt or SMBus alert output. Can be configured as a second THERM output. Open-drain; requires
pullup resistor to voltage between 1.7 V and 3.6 V.
D–
3
Analog input
Negative connection to remote temperature sensor.
D+
2
Analog input
Positive connection to remote temperature sensor.
GND
5
Ground
SCL
8
Digital input
SDA
7
THERM
4
Digital output
Thermal shutdown or fan-control pin. Open-drain; requires pullup resistor to voltage between 1.7 V and
3.6 V.
V+
1
Power supply
Positive supply voltage, 1.7 V to 3.6 V.
Supply ground connection.
Serial clock line for SMBus. Input; requires pullup resistor to voltage between 1.7 V and 3.6 V if driven
by open-drain output.
Bidirectional digital
Serial data line for SMBus. Open-drain; requires pullup resistor to voltage between 1.7 V and 3.6 V.
input-output
6 Specifications
6.1 Absolute Maximum Ratings
Over operating free-air temperature range, unless otherwise noted. (1)
Power supply
Input voltage
MIN
MAX
UNIT
V+
–0.3
3.6
V
THERM, ALERT/THERM2, SDA and SCL only
–0.3
3.6
V
D+ only
–0.3
(V+) + 0.3
V
D– only
–0.3
0.3
V
10
mA
–55
127
°C
150
°C
150
°C
Input current
Operating temperature
Junction temperature (TJmax)
Tstg
(1)
Storage temperature
–60
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1)
±2000
Charged device model (CDM), per JEDEC specification JESD22-C101, all
pins (2)
±750
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
3
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
TA
MIN
NOM
MAX
Supply voltage
1.7
3.3
Operating free-air temperature
–40
UNIT
3.6
V
125
°C
6.4 Thermal Information
TMP451
THERMAL METRIC (1)
DQF
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
RθJC(top)
Junction-to-case (top) thermal resistance
81.4
RθJB
Junction-to-board thermal resistance
137.9
ψJT
Junction-to-top characterization parameter
3.9
ψJB
Junction-to-board characterization parameter
140
(1)
171.3
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.5 Electrical Characteristics
At TA = –40°C to 125°C and V+ = 3.3 V, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
±0.25
±1
°C
±1
±2
°C
±0.25
±1
°C
TA = –40°C to 100°C, TD = –55°C to 150°C
±1
±2
°C
TA = –40°C to 125°C, TD = –55°C to 150°C
±2
±4
°C
±0.1
±0.25
31
34
TEMPERATURE ERROR
TELOCAL
Local temperature sensor
TA = 0°C to 70°C
TA = –40°C to 125°C
TA = 0°C to 70°C, TD = –55°C to 150°C
TEREMOTE
Remote temperature sensor (1)
Remote temperature sensor versus supply
(local or remote)
V+ = 1.7 V to 3.6 V
°C/V
TEMPERATURE MEASUREMENT
Conversion time
One-Shot mode, local and remote total
Local temperature sensor resolution
Remote temperature sensor resolution
Bits
12
Bits
120
μA
Remote sensor source current, medium
45
μA
Remote sensor source current, low
7.5
μA
Remote sensor source current, high
η
ms
12
Remote transistor ideality factor
Series resistance 1 kΩ max
TMP451 optimized ideality factor
1.008
SMBus INTERFACE
VIH
High-level input voltage
VIL
Low-level input voltage
1.4
Hysteresis
200
SMBus output low sink current
VOL
V
0.45
6
Low-level output voltage
IO = 6 mA
Logic input current
0 V ≤ VI ≤ 3.6 V
mA
0.15
–1
SMBus input capacitance
0.4
V
1
μA
3
SMBus clock frequency
0.01
SMBus time-out
20
V
mV
25
SCL falling edge to SDA valid time
pF
2.5
MHz
30
ms
1
μs
DIGITAL OUTPUTS ( THERM, ALERT/THERM2 )
VOL
Low-level output voltage
IO = 6 mA
IOH
High-level output leakage current
VO = V+
(1)
4
0.15
0.4
V
1
μA
Tested with less than 5-Ω effective series resistance and 100-pF differential input capacitance.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Electrical Characteristics (continued)
At TA = –40°C to 125°C and V+ = 3.3 V, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
POWER SUPPLY
V(V+)
Specified voltage range
1.7
3.6
V
27
40
μA
16 conversions per second
165
250
μA
32 conversions per second
300
450
μA
3
8
μA
0.0625 conversions per second
IQ
Quiescent current
POR
Serial bus inactive, shutdown mode
Serial bus active, ƒS = 400 kHz, shutdown mode
90
μA
Serial bus active, ƒS = 2.5 MHz, shutdown mode
350
μA
Power-on reset threshold
1.2
1.55
V
MAX
UNIT
2.5
MHz
6.6 Timing Requirements
FAST MODE
PARAMETER
MIN
TYP
HIGH-SPEED MODE
MAX
MIN
0.4
0.001
TYP
ƒ(SCL)
SCL operating frequency
0.001
t(BUF)
Bus free time between STOP and START Condition
1300
260
ns
t(HDSTA)
Hold time after repeated START condition. After this
period, the first clock is generated.
600
160
ns
t(SUSTA)
Repeated START condition setup time
600
160
ns
t(SUSTO)
STOP condition setup time
600
160
ns
t(HDDAT)
Data hold time
t(SUDAT)
Data setup time
t(LOW)
0
900
0
150
ns
100
30
ns
SCL clock LOW period
1300
260
ns
t(HIGH)
SCL clock HIGH period
600
60
ns
tF, tR –
SDA
Data fall and rise time
300
80
ns
tF, tR –
SCL
Clock fall and rise time
300
40
ns
tR
Rise time for SCL ≤ 100 kHz
t(LOW)
1000
tF
tR
ns
t(HDSTA)
SCL
t(HDSTA)
t(HIGH)
t(HDDAT)
t(SUSTO)
t(SUSTA)
t(SUDAT)
SDA
t(BUF)
P
S
S
P
Figure 1. Two-Wire Timing Diagram
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
5
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
6.7 Typical Characteristics
At TA = 25°C and V+ = 3.3 V, unless otherwise noted.
2
Mean
Mean - 4σ
Mean + 4σ
1.5
1
Remote Temperature Error (°C)
Local Temperature Error (°C)
2
0.5
0
-0.5
-1
-1.5
Mean - 4σ
Mean + 4σ
1
0.5
0
-0.5
-1
-1.5
-2
-2
-50
0
50
100
150
Ambient Temperature (°C)
-50
0
10
1.5
5HPRWH7HPSHUDWXUH(UURU Û&
2
-10
-20
-30
-40
D+ to GND
-50
100
150
C002
Figure 3. Remote Temperature Error vs Temperature
20
0
50
Ambient Temperature (°C)
C001
Figure 2. Local Temperature Error vs Temperature
5HPRWH7HPSHUDWXUH(UURU Û&
Mean
1.5
1
0.5
0
-0.5
-1
-1.5
D+ to V+
-60
-2
1
10
100
Leakage Resistance (M
)
0
1500
2000
Remote Temperature Error (°C)
90
-5
-10
-15
-20
-25
2500
3000
C004
Figure 5. Remote Temperature Error vs Series Resistance
0
5HPRWH7HPSHUDWXUH(UURU Û&
1000
Series Resistance (
)
Figure 4. Remote Temperature Error vs Leakage Resistance
20 mV p-p
50 mV p-p
100 mV p-p
80
70
60
50
40
30
20
10
0
-10
0
5
10
15
Differential Capacitance (nF)
20
0
200
400
600
Noise Frequency (MHz)
C005
Figure 6. Remote Temperature Error vs differential
Capacitance
6
500
C003
800
1000
C006
Figure 7. Remote Temperature Error vs Remote Channel
Noise Frequency
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Typical Characteristics (continued)
At TA = 25°C and V+ = 3.3 V, unless otherwise noted.
180
350
160
300
140
120
ISD ( A)
IQ ( A)
250
200
150
100
80
60
100
40
50
20
0
0
0.01
0.1
1
10
1
100
Conversion Rate (Hz)
10
100
1000
Clock Frequency (kHz)
C007
Figure 8. Quiescent Current vs Conversion Rate
10000
C008
Figure 9. Shutdown Quiescent Current
vs SCL Clock Frequency
170
3
2.5
165
ISD ( A)
IQ ( A)
2
160
155
1.5
1
150
0.5
145
0
1.5
2
2.5
3
Supply Voltage (V)
3.5
4
1.5
C009
Figure 10. Quiescent Current vs Supply Voltage
(At Default Conversion Rate of 16 Conversions per Second)
2
2.5
3
3.5
Supply Voltage (V)
Figure 11. Shutdown Quiescent Current
vs Supply Voltage
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
4
C010
7
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
7 Detailed Description
7.1 Overview
The TMP451 device is a digital temperature sensor that combines a local temperature measurement channel
and a remote-junction temperature measurement channel in a single DFN-8 package. The device is two-wireand SMBus-interface compatible, and is specified over a temperature range of –40°C to 125°C. The TMP451
device also contains multiple registers for programming and holding configuration settings, temperature limits,
and temperature measurement results.
7.2 Functional Block Diagram
V+
TMP451
Voltage Regulator
Register Bank
Oscillator
SCL
Serial Interface
Control Logic
SDA
16 x I
6xI
I
ALERT/THERM2
D+
ADC
DTHERM
Internal
BJT
GND
7.3 Feature Description
7.3.1 Temperature Measurement Data
The local and remote temperature sensors have a resolution of 12 bits (0.0625°C). Temperature data that result
from conversions within the default measurement range are represented in binary form, as shown in the
STANDARD BINARY column of Table 1. Any temperature below 0°C results in a data value of 0 (00h). Likewise,
temperatures above 127°C result in a value of 127 (7Fh). The device can be set to measure over an extended
temperature range by changing bit 2 (RANGE) of configuration register from low to high. The change in
measurement range and data format from standard binary to extended binary occurs at the next temperature
conversion. For data captured in the extended temperature range configuration, an offset of 64 (40h) is added to
the standard binary value, as shown in the EXTENDED BINARY column of Table 1. This configuration allows
measurement of temperatures as low as –64°C, and as high as 191°C; however, most temperature-sensing
diodes only measure with the range of –55°C to 150°C. Additionally, the TMP451 device is specified only for
ambient temperatures ranging from –40°C to 125°C; parameters in the Absolute Maximum Ratings table must be
observed.
8
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Feature Description (continued)
Table 1. Temperature Data Format (Local and Remote Temperature High Bytes)
LOCAL AND REMOTE TEMPERATURE REGISTER
HIGH BYTE VALUE (1°C RESOLUTION)
STANDARD BINARY (1)
EXTENDED BINARY (2)
TEMPERATURE
(°C)
BINARY
HEX
BINARY
–64
0000 0000
00
0000 0000
00
–50
0000 0000
00
0000 1110
0E
–25
0000 0000
00
0010 0111
27
0
0000 0000
00
0100 0000
40
1
0000 0001
01
0100 0001
41
5
0000 0101
05
0100 0101
45
10
0000 1010
0A
0100 1010
4A
25
0001 1001
19
0101 1001
59
50
0011 0010
32
0111 0010
72
75
0100 1011
4B
1000 1011
8B
100
0110 0100
64
1010 0100
A4
125
0111 1101
7D
1011 1101
BD
127
0111 1111
7F
1011 1111
BF
150
0111 1111
7F
1101 0110
D6
175
0111 1111
7F
1110 1111
EF
191
0111 1111
7F
1111 1111
FF
(1)
(2)
HEX
Resolution is 1°C/count. Negative values produce a read of 0°C.
Resolution is 1°C/count. All values are unsigned with a –64°C offset.
Both local and remote temperature data use two bytes for data storage. The high byte stores the temperature
with 1°C resolution. The second or low byte stores the decimal fraction value of the temperature and allows a
higher measurement resolution, as shown in Table 2. The measurement resolution for both the local and the
remote channels is 0.0625°C.
Table 2. Decimal Fraction Temperature Data Format (Local and Remote Temperature Low Bytes)
(1)
TEMPERATURE REGISTER LOW BYTE VALUE
(0.0625°C RESOLUTION) (1)
TEMP
(°C)
STANDARD AND EXTENDED BINARY
HEX
0
0000 0000
00
0.0625
0001 0000
10
0.1250
0010 0000
20
0.1875
0011 0000
30
0.2500
0100 0000
40
0.3125
0101 0000
50
0.3750
0110 0000
60
0.4375
0111 0000
70
0.5000
1000 0000
80
0.5625
1001 0000
90
0.6250
1010 0000
A0
0.6875
1011 0000
B0
0.7500
1100 0000
C0
0.8125
1101 0000
D0
0.8750
1110 0000
E0
0.9385
1111 0000
F0
Resolution is 0.0625°C/count. All possible values are shown.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
9
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
7.3.1.1 Standard Binary-to-Decimal Temperature Data Calculation Example
High-byte conversion (for example, 0111 0011):
Convert the right-justified binary high byte to hexadecimal.
From hexadecimal, multiply the first number by 160 = 1 and the second number by 161 = 16.
The sum equals the decimal equivalent.
0111 0011b → 73h → (3 × 160) + (7 × 161) = 115
Low-byte conversion (for example, 0111 0000):
To convert the left-justified binary low-byte to decimal, use bits 7 through 4 and ignore bits 3 through 0
because they do not affect the value of the number.
0111b → (0 × 1/2)1 + (1 × 1/2)2 + (1 × 1/2)3 + (1 × 1/2)4 = 0.4375
7.3.1.2 Standard Decimal-to-Binary Temperature Data Calculation Example
For positive temperatures (for example, 20°C):
(20°C) / (1°C/count) = 20 → 14h → 0001 0100
Convert the number to binary code with 8-bit, right-justified format, and MSB = 0 to denote a positive sign.
20°C is stored as 0001 0100 → 14h.
For negative temperatures (for example, –20°C):
(|–20|) / (1°C/count) = 20 → 14h → 0001 0100
Generate the two's complement of a negative number by complementing the absolute value binary number
and adding 1.
–20°C is stored as 1110 1100 → ECh.
7.3.2 Series Resistance Cancellation
Series resistance cancellation automatically eliminates the temperature error caused by the resistance of the
routing to the remote transistor or by the resistors of the optional external low-pass filter. A total of up to 1 kΩ of
series resistance can be cancelled by the TMP451 device, eliminating the need for additional characterization
and temperature offset correction. See Figure 5 for details on the effects of series resistance on sensed remote
temperature error.
7.3.3 Differential Input Capacitance
The TMP451 device tolerates differential input capacitance of up to 1000 pF with minimal change in temperature
error. The effect of capacitance on sensed remote temperature error is shown in Figure 6.
7.3.4 Filtering
Remote junction temperature sensors are usually implemented in a noisy environment. Noise is most often
created by fast digital signals, and it can corrupt measurements. The TMP451 device has a built-in, 65-kHz filter
on the inputs of D+ and D– to minimize the effects of noise. However, a bypass capacitor placed differentially
across the inputs of the remote temperature sensor is recommended to make the application more robust against
unwanted coupled signals. For this capacitor, select a value of between 100 pF and 1 nF. Some applications
attain better overall accuracy with additional series resistance; however, this increased accuracy is applicationspecific. When series resistance is added, the total value should not be greater than 1 kΩ. If filtering is required,
suggested component values are 100 pF and 50 Ω on each input; exact values are application-specific.
10
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Additionally, a digital filter is available for the remote temperature measurements to further reduce the effect of
noise. This filter is programmable and has two levels when enabled. Level 1 performs a moving average of four
consecutive samples. Level 2 performs a moving average of eight consecutive samples. The value stored in the
remote temperature result register is the output of the digital filter, and the ALERT and THERM limits are
compared to it. This provides additional immunity to noise and spikes on the ALERT and THERM outputs. The
filter responses are shown in Figure 12. The filter can be enabled or disabled by programming the desired levels
in the digital filter register. The digital filter is disabled by default and on POR.
Step response
100
90
90
80
80
70
Temperature (°C)
Temperature (°C)
Impulse Response
100
Disabled
60
50
40
Level1
Level2
30
70
Disabled
60
Level1
Level2
50
40
30
20
20
10
10
0
0
0
1
2
3
4
5
6
7 8
9
Samples
10
11 12
13
14
15
0
1
2
3
4
5
6
7 8
9
Samples
10
11 12
13
14
15
Figure 12. Filter Response to Impulse and Step Inputs
7.3.5 Sensor Fault
The TMP451 device can sense a fault at the D+ input resulting from incorrect diode connection. The TMP451
device can also sense an open circuit. Short-circuit conditions return a value of –64°C. The detection circuitry
consists of a voltage comparator that trips when the voltage at D+ exceeds (V+) – 0.3 V (typical). The
comparator output is continuously checked during a conversion. If a fault is detected, then OPEN (bit 2) in the
status register is set to 1.
When not using the remote sensor with the TMP451 device, the D+ and D– inputs must be connected together
to prevent meaningless fault warnings.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
11
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
7.3.6
www.ti.com
ALERT and THERM Functions
The operation of the ALERT (pin 6) and THERM (pin 4) interrupts is shown in Figure 13. The operation of the
THERM (pin 4) and THERM2 (pin 6) interrupts is shown in Figure 14.
Temperature Conversion Complete
Temperature Conversion Complete
150
150
140
140
130
130
Temperature (°C)
110
THERM Limit
100
THERM Limit - Hysteresis
90
High Temperature Limit
80
Temperature (°C)
120
120
110
THERM Limit
100
THERM Limit - Hysteresis
90
THERM2 Limit
80
THERM2 Limit - Hysteresis
70
Measured
Temperature
60
70
Measured
Temperature
60
50
50
Time
Time
ALERT output
serviced by master
THERM2
ALERT
THERM
THERM
Figure 13. ALERT and THERM Interrupt Operation
Figure 14. THERM and THERM2 Interrupt
Operation
The hysteresis value is stored in the THERM hysteresis register. The value of the CONAL[2:0] bits in the
consecutive ALERT register determines the number of limit violations before the ALERT pin is tripped. The
default value is 000b and corresponds to one violation, 001b programs two consecutive violations, 011b
programs three consecutive violations, and 111b programs four consecutive violations. This provides additional
filtering for the ALERT pin state.
7.4 Device Functional Modes
7.4.1 Shutdown Mode (SD)
The TMP451 shutdown mode enables the user to save maximum power by shutting down all device circuitry
other than the serial interface, reducing current consumption to typically less than 3 μA; see Figure 11. Shutdown
mode is enabled when the SD bit (bit 6) of the configuration register is high; the device shuts down after the
current conversion is finished. When the SD bit is low, the device maintains a continuous-conversion state.
7.4.2 One-shot Mode
When the TMP451 device is in shutdown mode (SD = 1 in the configuration register), a single conversion is
started by writing any value to the one-shot start register, pointer address 0Fh. This write operation starts one
conversion and comparison cycle on both the local and the remote sensors. The TMP451 device returns to
shutdown mode when the cycle completes. The value of the data sent in the write command is irrelevant and is
not stored by the TMP451 device.
7.5 Programming
7.5.1 Serial Interface
The TMP451 device operates only as a slave device on either the two-wire bus or the SMBus. Connections to
either bus are made using the open-drain I/O lines, SDA and SCL. The SDA and SCL pins feature integrated
spike suppression filters and Schmitt triggers to minimize the effects of input spikes and bus noise. The TMP451
device supports the transmission protocol for fast (1 kHz to 400 kHz) and high-speed (1 kHz to 2.5 MHz) modes.
All data bytes are transmitted MSB first.
12
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Programming (continued)
7.5.1.1 Bus Overview
The TMP451 device is SMBus interface compatible. In SMBus protocol, the device that initiates the transfer is
called a master, and the devices controlled by the master are slaves. The bus must be controlled by a master
device that generates the serial clock (SCL), controls the bus access, and generates the START and STOP
conditions.
To address a specific device, a START condition is initiated. A START condition is indicated by pulling the data
line (SDA) from a high-to-low logic level while SCL is high. All slaves on the bus shift in the slave address byte,
with the last bit indicating whether a read or write operation is intended. During the ninth clock pulse, the slave
being addressed responds to the master by generating an acknowledge bit and pulling SDA low.
Data transfer is then initiated and sent over eight clock pulses followed by an acknowledge bit. During data
transfer SDA must remain stable while SCL is high, because any change in SDA while SCL is high is interpreted
as a control signal.
After all data have been transferred, the master generates a STOP condition. A STOP condition is indicated by
pulling SDA from low to high, while SCL is high.
7.5.1.2 Bus Definitions
The TMP451 device is two-wire and SMBus-compatible. Figure 15 and Figure 16 show the timing for various
operations on the TMP451 device. The bus definitions are as follows:
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge bit. A device
that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a way
that the SDA line is stable low during the high period of the acknowledge clock pulse. Take setup
and hold times into account. On a master receive, data transfer termination can be signaled by the
master generating a not-acknowledge on the last byte that has been transmitted by the slave.
Bus Idle:
Both SDA and SCL lines remain high.
Data Transfer: The number of data bytes transferred between a START and a STOP condition is not limited and
is determined by the master device. The receiver acknowledges data transfer.
Start Data Transfer: A change in the state of the SDA line, from high to low, while the SCL line is high, defines
a start condition. Each data transfer initiates with a START condition.
Stop Data Transfer: A change in the state of the SDA line from low to high while the SCL line is high defines a
STOP condition. Each data transfer terminates with a repeated START or STOP condition.
1
9
9
1
SCL
¼
SDA
1
0
0
1
1
0
0(1)
R/W
Start By
Master
P7
P6
P5
P4
P3
P2
P1
P0
ACK By
Device
¼
ACK By
Device
Frame 2 Pointer Register Byte
Frame 1 Two-Wire Slave Address Byte
9
1
SCL
(Continued)
SDA
(Continued)
D7
D6
D5
D4
D3
D2
D1
D0
ACK By
Device
Stop By
Master
Frame 3 Data Byte 1
(1) Slave address 1001100 shown.
Figure 15. Two-Wire Timing Diagram for Write Word Format
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
13
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
Programming (continued)
1
9
1
9
SCL
¼
SDA
1
0
0
1
1
0
0(1)
P7
R/W
Start By
Master
P6
P5
P4
P3
P2
P1
P0
ACK By
Device
ACK By
Device
Frame 1 Two-Wire Slave Address Byte
1
¼
Frame 2 Pointer Register Byte
9
1
9
SCL
(Continued)
¼
SDA
(Continued)
1
0
0
1
1
0
0(1)
R/W
Start By
Master
D7
D6
ACK By
Device
Frame 3 Two-Wire Slave Address Byte
D5
D4
D3
D2
D1
D0
From
Device
¼
NACK By
Master(2)
Frame 4 Data Byte 1 Read Register
(1) Slave address 1001100 shown.
(2) Master should leave SDA high to terminate a single-byte read operation.
Figure 16. Two-Wire Timing Diagram for Single-Byte Read Format
7.5.1.3 Serial Bus Address
To communicate with the TMP451 device, the master must first address slave devices using a slave address
byte. The slave address byte consists of seven address bits, and a direction bit indicating the intent of executing
a read or write operation. The TMP451 device has a device address of 4Ch (1001 100b). Additional factoryprogrammed device addresses are available upon request.
7.5.1.4 Read and Write Operations
Accessing a particular register on the TMP451 device is accomplished by writing the appropriate value to the
pointer register. The value for the pointer register is the first byte transferred after the slave address byte with the
R/W bit low. Every write operation to the TMP451 device requires a value for the pointer register (see Figure 15).
When reading from the TMP451 device the last value stored in the pointer register by a write operation is used to
determine which register is read by a read operation. To change which register is read for a read operation, a
new value must be written to the pointer register. This transaction is accomplished by issuing a slave address
byte with the R/W bit low, followed by the pointer register byte; no additional data are required. The master can
then generate a START condition and send the slave address byte with the R/W bit high to initiate the read
command; see Figure 16 for details of this sequence.
If repeated reads from the same register are desired, it is not necessary to continually send the pointer register
bytes, because the TMP451 device retains the pointer register value until it is changed by the next write
operation. The register bytes are sent MSB first, followed by the LSB.
Read operations should be terminated by issuing a not-acknowledge command at the end of the last byte to be
read. For single-byte operation, the master must leave the SDA line high during the acknowledge time of the first
byte that is read from the slave.
14
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Programming (continued)
7.5.1.5 Time-out Function
If the SMBus time-out function is enabled, the TMP451 device resets the serial interface if either SCL or SDA are
held low for 25 ms (typical) between a START and STOP condition. If the TMP451 device is holding the bus low,
the device releases the bus and waits for a START condition. To avoid activating the time-out function,
maintaining a communication speed of at least 1 kHz for the SCL operating frequency is necessary. The SMBTO
bit (bit 7) of the consecutive ALERT register controls the time-out enable. Setting the SMBTO bit to a value of 0
(default) disables the time-out. Setting the SMBTO bit to a value of 1 enables the function.
7.5.1.6 High-speed Mode
For the two-wire bus to operate at frequencies above 1 MHz, the master device must issue a high-speed mode
(Hs-mode) master code (0000 1xxx) as the first byte after a START condition to switch the bus to high-speed
operation. The TMP451 device does not acknowledge this byte, but switches the input filters on SDA and SCL
and the output filter on SDA to operate in Hs-mode, allowing transfers at up to 2.5 MHz. After the Hs-mode
master code has been issued, the master transmits a two-wire slave address to initiate a data transfer operation.
The bus continues to operate in Hs-mode until a STOP condition occurs on the bus. Upon receiving the STOP
condition, the TMP451 device switches the input and output filters back to fast mode operation.
7.5.1.7 General Call Reset
The TMP451 device supports reset using the two-wire general call address 00h (0000 0000b). The TMP451
device acknowledges the general call address and responds to the second byte. If the second byte is 06h (0000
0110b), the TMP451 device executes a software reset. This software reset restores the power-on reset state to
all TMP451 registers, and it aborts any conversion in progress. The TMP451 device takes no action in response
to other values in the second byte.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
15
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
7.6 Register Map
Table 3. Register Map
BIT DESCRIPTION
POINTER READ
(HEX)
POINTER
WRITE (HEX)
POR (HEX)
7
6
5
4
3
2
1
0
00
N/A
00
LT11
LT10
LT9
LT8
LT7
LT6
LT5
LT4
Local temperature (high byte)
01
N/A
00
RT11
RT10
RT9
RT8
RT7
RT6
RT5
RT4
Remote temperature (high byte)
02
N/A
N/A
BUSY
LHIGH
LLOW
RHIGH
RLOW
OPEN
RTHRM
LTHRM
SD
ALERT/
THERM2
0
0
RANGE
0
0
16
MASK1
REGISTER DESCRIPTION
Status register
03
09
00
04
0A
08
0
0
0
0
CR3
CR2
CR1
CR0
05
0B
55
LTHL11
LTHL10
LTHL9
LTHL8
LTHL7
LTHL6
LTHL5
LTHL4
Local temperature high limit
06
0C
00
LTLL11
LTLL10
LTLL9
LTLL8
LTLL7
LTLL6
LTLL5
LTLL4
Local temperature low limit
07
0D
55
RTHL11
RTHL10
RTHL9
RTHL8
RTHL7
RTHL6
RTHL5
RTHL4
Remote temperature high limit (high byte)
08
0E
00
RTLL11
RTLL10
RTLL9
RTLL8
RTLL7
RTLL6
RTLL5
RTLL4
Remote temperature low limit (high byte)
N/A
0F
N/A
X
X
X
X
X
X
X
X
One-shot start Table 14
10
N/A
00
RT3
RT2
RT1
RT0
0
0
0
0
Remote temperature (low byte)
11
11
00
RTOS11
RTOS10
RTOS9
RTOS8
RTOS7
RTOS6
RTOS5
RTOS4
Remote temperature offset (high byte)
12
12
00
RTOS3
RTOS2
RTOS1
RTOS0
0
0
0
0
Remote temperature offset (low byte)
13
13
00
RTHL3
RTHL2
RTHL1
RTHL0
0
0
0
0
Remote temperature high limit (low byte)
14
14
00
RTLL3
RTLL2
RTLL1
RTLL0
0
0
0
0
Remote temperature low limit (low byte)
15
N/A
00
LT3
LT2
LT1
LT0
0
0
0
0
Local temperature (low byte)
19
19
6C
RTH11
RTH10
RTH9
RTH8
RTH7
RTH6
RTH5
RTH4
Remote temperature THERM limit
20
20
55
LTH11
LTH10
LTH9
LTH8
LTH7
LTH6
LTH5
LTH4
Local temperature THERM limit
21
21
0A
HYS11
HYS10
HYS9
HYS8
HYS7
HYS6
HYS5
HYS4
THERM hysteresis
22
22
01
SMBTO
0
0
0
CONAL2
CONAL1
CONAL0
1
23
23
00
NC7
NC6
NC5
NC4
NC3
NC2
NC1
NC0
η-factor correction
24
24
00
0
0
0
0
0
0
DF1
DF0
Digital filter control
FE
N/A
55
0
1
0
1
0
1
0
1
Submit Documentation Feedback
Configuration register
Conversion rate register
Consecutive ALERT
Manufacturer ID
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
7.6.1 Register Information
The TMP451 device contains multiple registers for holding configuration information, temperature measurement
results, and status information. These registers are described in Figure 17 and Table 3.
7.6.1.1 Pointer Register
Figure 17 shows the internal register structure of the TMP451 device. The 8-bit pointer register is used to
address a given data register. The pointer register identifies which of the data registers should respond to a read
or write command on the two-wire bus. This register is set with every write command. A write command must be
issued to set the proper value in the pointer register before executing a read command. Table 3 describes the
pointer register and the internal structure of the TMP451 registers. The power-on reset (POR) value of the
pointer register is 00h (0000 0000b).
Pointer Register
Local and Remote Temperature Registers
Status Register
Configuration Register
SDA
Conversion Rate Register
Local and Remote Temperature Limit Registers
One-Shot Start Register
Remote Temperature Offset Registers
I/O
Control
Interface
Local and Remote THERM Limit Registers
THERM Hysteresis Register
Consecutive ALERT Register
N-factor Correction Register
SCL
Digital Filter Register
Manufacturer ID Register
Figure 17. Internal Register Structure
7.6.1.2 Temperature Registers
The TMP451 device has multiple 8-bit registers that hold temperature measurement results. The eight most
significant bits (MSBs) of the local temperature sensor result are stored in register 00h, while the four least
significant bits (LSBs) are stored in register 15h (the four MSBs of register 15h). The eight MSBs of the remote
temperature sensor result are stored in register 01h, and the four LSBs are stored in register 10h (the four MSBs
of register 10h). The four LSBs of both the local sensor and the remote sensor indicate the temperature value
after the decimal point (for example, if the temperature result is 10.0625˚C, the high byte is 0000 1010 and the
low byte is 0001 0000). These registers are read-only and are updated by the ADC each time a temperature
measurement.
When the full temperature value is needed, reading the MSB value first causes the LSB value to be locked (the
ADC does not write to it) until it is read. The same thing happens upon reading the LSB value first (the MSB
value is locked until it is read). This mechanism assures that both bytes of the read operation are from the same
ADC conversion. This assurance remains valid only until another register is read. For proper operation, read the
high byte of the temperature result first. Read the low byte register in the next read command; if the LSBs are not
needed, the register may be left unread. The power-on reset value of all temperature registers is 00h.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
17
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
7.6.1.3 Local Temperature High Byte Register (offset: Read = 00h; Write = N/A) [reset = 00h]
Figure 18. Local Temperature High Byte Register
7
LT11
R-0
6
LT10
R-0
5
LT9
R-0
4
LT8
R-0
3
LT7
R-0
2
LT6
R-0
1
LT5
R-0
0
LT4
R-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 4. Local Temperature High Byte Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
LT11 - LT4
R
0h
Local temperature high byte. The resolution of the LSB in this
register is 1°C. This register is read-only and is updated by the
ADC each time a temperature measurement is completed. When
the full temperature value is needed, reading the high byte
register first causes the low byte register value to be locked (the
ADC does not write to it) until it is read. The same thing happens
upon reading the low byte register value first (the high byte
register value is locked until it is read). This mechanism assures
that both bytes of the read operation are from the same ADC
conversion. This assurance remains valid only until another
register is read. For proper operation, read the high byte of the
temperature result first. Read the low byte register in the next
read command; if the low byte is not needed, the register may
be left unread.
7.6.1.4 Remote Temperature High Byte Register (offset: Read = 01h; Write = N/A) [reset = 00h]
Figure 19. Remote Temperature High Byte Register
7
RT11
R-0h
6
RT10
R-0h
5
RT9
R-0h
4
RT8
R-0h
3
RT7
R-0h
2
RT6
R-0h
1
RT5
R-0h
0
RT4
R-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 5. Remote Temperature High Byte Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
RT11 - RT4
R
0h
Remote temperature high byte. The resolution of the LSB in this
register is 1 °C.
This register is read-only and is updated by the ADC each time
a temperature measurement is completed. When the full
temperature value is needed, reading the high byte register first
causes the low byte register value to be locked (the ADC does
not write to it) until it is read. The same thing happens upon
reading the low byte register value first (the high byte register
value is locked until it is read). This mechanism assures that
both bytes of the read operation are from the same ADC
conversion. This assurance remains valid only until another
register is read. For proper operation, read the high byte of the
temperature result first. Read the low byte register in the next
read command; if the low byte is not needed, the register may
be left unread.
7.6.1.5 Status Register (offset: Read = 02h; Write = N/A) [reset = N/A]
Figure 20. Status Register
7
BUSY
R
6
LHIGH
R
5
LLOW
R
4
RHIGH
R
3
RLOW
R
2
OPEN
R
1
RTHRM
R
0
LTHRM
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
18
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Table 6. Status Register Field Descriptions
(1)
Bit
Field
Type
Reset
Description
7
BUSY
R
N/A
ADC status indicator
1 = ADC is converting.
0 = ADC is not converting.
6
LHIGH
R
N/A
Local temperature high limit status indicator (1)
1 = Local temperature value exceeds the Local Temperature
High Limit Register value. This bit is cleared upon reading the
Status Register providing that the condition causing the over
temperature result is no longer present.
0 = Local temperature value does not exceed the Local
Temperature High Limit Register value.
5
LLOW
R
N/A
Local temperature low limit status indicator (1)
1 = Local temperature value is below the Local Temperature
Low Limit Register value. This bit is cleared upon reading the
Status Register providing that the condition causing the under
temperature result is no longer present.
0 = Local temperature value is not below the Local Temperature
Low Limit Register value.
4
RHIGH
R
N/A
Remote temperature high limit status indicator (1)
1 = Remote temperature value exceeds the Remote
Temperature High Limit Register value. This bit is cleared upon
reading the Status Register providing that the condition causing
the over temperature result is no longer present.
0 = Remote temperature value does not exceed the Remote
Temperature High Limit Register value.
3
RLOW
R
N/A
Remote temperature low limit status indicator (1)
1 = Remote temperature value is below the Remote
Temperature Low Limit Register value. This bit is cleared upon
reading the Status Register providing that the condition causing
the under temperature result is no longer present.
0 = Remote temperature value is not below the Remote
Temperature Low Limit Register value.
2
OPEN
R
N/A
Remote junction open circuit detection (1)
1 = The remote junction is an open circuit. This bit is cleared
upon reading the Status Register providing that the condition
causing the open circuit is no longer present.
0 = The remote junction is not an open circuit.
1
RTHRM
R
N/A
Remote THERM limit status indicator
1 = Remote THERM limit is tripped. This bit is cleared upon
reading the Status Register providing that the condition causing
the over temperature result is no longer present.
0 = Remote THERM limit is not tripped.
0
LTHRM
R
N/A
Local THERM limit status indicator
1 = Local THERM limit is tripped. This bit is cleared upon
reading the Status Register providing that the condition causing
the over temperature result is no longer present.
0 = Local THERM limit is not tripped.
These flags stay high until the status register is read or they are reset by a POR when pin 6 is configured as ALERT. Only bit 2 (OPEN)
stays high until the status register is read or it is reset by a POR when pin 6 is configured as THERM2.
The status register reports the state of the temperature ADC, the temperature limit comparators, and the
connection to the remote sensor. Table 6 lists the status register bits. The status register is read-only, and is
read by accessing pointer address 02h.
The LHIGH and LLOW bits indicate a local sensor overtemperature or undertemperature event, respectively. The
RHIGH and RLOW bits indicate a remote sensor overtemperature or undertemperature event, respectively. The
OPEN bit indicates an open-circuit condition on the remote sensor. When pin 6 is configured as the ALERT
output, the five flags are NORed together. If any of the five flags are high, the ALERT interrupt latch is set and
the ALERT output goes low. Reading the status register clears the five flags, provided that the condition that
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
19
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
caused the setting of the flags is not present anymore (that is, the value of the corresponding result register is
within the limits, or the remote sensor is connected properly and functional). The ALERT interrupt latch (and the
ALERT pin correspondingly) is not reset by reading the status register. The reset is done by the master reading
the temperature sensor device address to service the interrupt, and only if the flags have been reset and the
condition that caused them to be set is not present.
The RTHRM and LTHRM flags are set when the corresponding temperature exceeds the programmed THERM
limit. They are reset automatically when the temperature returns to within the limits. The THERM output goes low
in the case of overtemperature on either the local or the remote channel, and goes high as soon as the
measurements are within the limits again. The THERM hysteresis register (21h) allows hysteresis to be added so
that the flag resets and the output goes high when the temperature returns to or goes below the limit value minus
the hysteresis value.
When pin 6 is configured as THERM2, only the high limits matter. The LHIGH and RHIGH flags are set if the
respective temperatures exceed the limit values, and the pin goes low to indicate the event. The LLOW and
RLOW flags have no effect on THERM2, and the output behaves the same way when configured as THERM.
7.6.1.6 Configuration Register (offset: Read = 03h; Write = 09h) [reset = 00h]
Figure 21. Configuration Register
7
MASK1
6
SD
R/W-0h
R/W-0h
5
ALERT/THERM
2
R/W-0h
4
RESERVED
3
2
RANGE
R/W-0h
R/W-0h
1
0
RESERVED
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7. Configuration Register Field Descriptions
Bit
Field
Type
Reset
Description
7
MASK1
R/W
0h
This bit masks the ALERT output
1 = ALERT is disabled.
0 = ALERT is enabled.
6
SD
R/W
0h
Device shutdown control
1 = Places the device is in shutdown mode.
0 = Places the device in continuous conversion mode.
5
ALERT/THERM2
R/W
0h
ALERT or THERM2 mode select
1 = THERM2 mode
0 = ALERT mode
2
RANGE
R/W
0h
This bit configures the range of the temperature measurement
1 = –64 °C to 191°C
0 = 0 °C to 127°C
MASK1 of the configuration register masks the ALERT output. If MASK1 is 0 (default), the ALERT output is
enabled. If MASK1 is set to 1, the ALERT output is disabled. This configuration applies only if the value of
ALERT/THERM2 bit is 0 (that is, pin 6 is configured as the ALERT output). If pin 6 is configured as the THERM2
output, the value of the MASK1 bit has no effect.
The shutdown bit, SD, enables or disables the temperature-measurement circuitry. If SD = 0 (default), the
TMP451 device converts continuously at the rate set in the conversion rate register. When SD is set to 1, the
TMP451 device stops converting when the current conversion sequence is complete and enters a shutdown
mode. When SD is set to 0 again, the TMP451 resumes continuous conversions. When SD = 1, a single
conversion can be started by writing to the one-shot start register. See the One-shot Mode section for more
information.
ALERT/THERM2 (bit 5) sets the configuration of pin 6. If the ALERT/THERM2 bit is 0 (default), then pin 6 is
configured as the ALERT output; if it is set to 1, then pin 6 is configured as the THERM2 output.
The temperature range is set by configuring RANGE (bit 2) of the configuration register. Setting this bit low
(default) configures the TMP451 device for the standard measurement range (0°C to 127°C); temperature
conversions are stored in the standard binary format. Setting bit 2 high configures the TMP451 device for the
extended measurement range (–64°C to 191°C); temperature conversions are stored in the extended binary
format (see Table 1).
20
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
The remaining bits of the configuration register are reserved and must always be set to 0. The power-on reset
value for this register is 00h.
7.6.1.7 Conversion Rate Register (offset: Read = 04h; Write = 0Ah) [reset = 08h]
Figure 22. Conversion Rate Register
7
6
5
4
3
CR3
R/W-1h
RESERVED
R/W-0h
2
CR2
R/W-0h
1
CR1
R/W-0h
0
CR0
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 8. Conversion Rate Register Field Descriptions
Bit
3-0
Field
Type
Reset
Description
CR3 - CR0
R/W
8h
Conversion rate selection. Refer to Table 9
The conversion rate register (read address 04h, write address 0Ah) controls the rate at which temperature
conversions are performed. This register adjusts the idle time between conversions but not the conversion time
itself, thereby allowing the TMP451 power dissipation to be balanced with the temperature register update rate.
Table 9 lists the conversion rate options and corresponding time between conversions. The default value of the
register is 08h, which gives a default rate of 16 conversions per second.
Table 9. Conversion Rate
VALUE
CONVERSIONS PER SECOND
TIME (SECONDS)
00h
0.0625
16
01h
0.125
8
02h
0.25
4
03h
0.5
2
04h
1
1
05h
2
0.5
06h
4
0.25
07h
8
0.125
08h
16 (default)
0.0625 (default)
09h
32
0.03125
7.6.1.8 Local Temperature High Limit Register (offset: Read = 05h; Write = 0Bh) [reset = 55h]
Figure 23. Local Temperature High Limit Register
7
LTHL11
R/W-0h
6
LTHL10
R/W-1h
5
LTHL9
R/W-0h
4
LTHL8
R/W-1h
3
LTHL7
R/W-0h
2
LTHL6
R/W-1h
1
LTHL5
R/W-0h
0
LTHL4
R/W-1h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 10. Local Temperature High Limit Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
LTHL11 - LTHL4
R/W
55h
These bits determine the value of the high temperature limit to
which the local temperature measurement is compared. The
resolution of the LSB in this register is 1°C.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
21
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
7.6.1.9 Local Temperature Low Limit Register (offset: Read = 06h; Write = 0Ch) [reset = 00h]
Figure 24. Local Temperature Low Limit Register
7
LTLL11
R/W-0h
6
LTLL10
R/W-0h
5
LTLL9
R/W-0h
4
LTLL8
R/W-0h
3
LTLL7
R/W-0h
2
LTLL6
R/W-0h
1
LTLL5
R/W-0h
0
LTLL4
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 11. Local Temperature Low Limit Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
LTLL11 - LTLL4
R/W
00h
These bits determine the value of the low temperature limit to
which the local temperature measurement is compared. The
resolution of the LSB in this register is 1°C.
7.6.1.10 Remote Temperature High Limit High Byte Register (offset: Read = 07h; Write = 0Dh) [reset =
55h]
Figure 25. Remote Temperature High Limit High Byte Register
7
RTHL11
R/W-0h
6
RTHL10
R/W-1h
5
RTHL9
R/W-0h
4
RTHL8
R/W-1h
3
RTHL7
R/W-0h
2
RTHL6
R/W-1h
1
RTHL5
R/W-0h
0
RTHL4
R/W-1h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 12. Remote Temperature High Limit High Byte Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
RTHL11 - RTHL4
R/W
55h
These bits determine the value of the high byte of the high
temperature limit to which the remote temperature measurement
is compared. The resolution of the LSB in this register is 1°C.
7.6.1.11 Remote Temperature Low Limit High Byte Register (offset: Read = 08h; Write = 0Eh) [reset =
00h]
Figure 26. Remote Temperature Low Limit High Byte Register
7
RTLL11
R/W-0h
6
RTLL10
R/W-0h
5
RTLL9
R/W-0h
4
RTLL8
R/W-0h
3
RTLL7
R/W-0h
2
RTLL6
R/W-0h
1
RTLL5
R/W-0h
0
RTLL4
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 13. Remote Temperature Low Limit High Byte Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
RTLL11 - RTLL4
R/W
00h
These bits determine the value of high byte of the low
temperature limit to which the remote temperature measurement
is compared. The resolution of the LSB in this register is 1°C.
7.6.1.12 One-shot Start Register (offset: Read = N/A; Write = 0Fh) [reset = N/A]
Figure 27. One-shot Start Register
7
X
W
6
X
W
5
X
W
4
X
W
3
X
W
2
X
W
1
X
W
0
X
W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
22
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Table 14. One-shot Start Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
X
W
N/A
When the device is in the shutdown mode writing any value to
this register will trigger a one-shot temperature conversion.
7.6.1.13 Remote Temperature Low Byte Register (offset: Read = 10h; Write = N/A) [reset = 00h]
Figure 28. Remote Temperature Low Byte Register
7
RT3
R-0h
6
RT2
R-0h
5
RT1
R-0h
4
RT0
R-0h
3
2
1
0
RESERVED
R-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 15. Remote Temperature Low Byte Register Field Descriptions
Bit
7-4
Field
Type
Reset
Description
RT3 - RT0
R
0h
Remote temperature low byte. The resolution of the LSB in this
register is 0.0625 °C.
This register is read-only and is updated by the ADC each time
a temperature measurement is completed. When the full
temperature value is needed, reading the high byte register first
causes the low byte register value to be locked (the ADC does
not write to it) until it is read. The same thing happens upon
reading the low byte register value first (the high byte register
value is locked until it is read). This mechanism assures that
both bytes of the read operation are from the same ADC
conversion. This assurance remains valid only until another
register is read. For proper operation, read the high byte of the
temperature result first. Read the low byte register in the next
read command; if the low byte is not needed, the register may
be left unread. The resolution of these four bits is 0.0625 °C.
7.6.1.14 Remote Temperature Offset High Byte Register (offset: Read = 11h; Write = 11h) [reset = 00h]
Figure 29. Remote Temperature Offset High Byte Register
7
RTOS11
R/W-0h
6
RTOS10
R/W-0h
5
RTOS9
R/W-0h
4
RTOS8
R/W-0h
3
RTOS7
R/W-0h
2
RTOS6
R/W-0h
1
RTOS5
R/W-0h
0
RTOS4
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 16. Remote Temperature Offset High Byte Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
RTOS11 - RTOS4
R/W
00h
Remote temperature offset high byte. The value of this register
is added to the value the ADC conversion with the result stored
in the remote temperature register. This register is used to add
or subtract a temperature offset value to the ADC conversion
result in applications requiring calibration. The resolution of the
LSB in this register is 1 °C.
The offset register allows the TMP451 device to store any system offset compensation value that might be
observed from precision calibration. The value in the register is stored in the same format as the temperature
result, and is added to the remote temperature result upon every conversion. Combined with the η-factor
correction, this function allows for very accurate system calibration over the entire temperature range.
7.6.1.15 Remote Temperature Offset Low Byte Register (offset: Read = 12h; Write = 12h) [reset = 00h]
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
23
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
Figure 30. Remote Temperature Offset Low Byte Register
7
RTOS3
R/W-0h
6
RTOS2
R/W-0h
5
RTOS1
R/W-0h
4
RTOS0
R/W-0h
3
2
1
0
RESERVED
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 17. Remote Temperature Offset Low Byte Register Field Descriptions
Bit
7-4
Field
Type
Reset
Description
RTOS3 - RTOS0
R/W
0h
Remote temperature offset low byte. The value of this register is
added to the value the ADC conversion with the result stored in
the remote temperature register. This register is used to add or
subtract a temperature offset value to the ADC conversion result
in applications requiring calibration. The resolution of these four
bits is 0.0625°C.
The offset register allows the TMP451 device to store any system offset compensation value that might be
observed from precision calibration. The value in the register is stored in the same format as the temperature
result, and is added to the remote temperature result upon every conversion. Combined with the η-factor
correction, this function allows for very accurate system calibration over the entire temperature range.
7.6.1.16 Remote Temperature High Limit Low Byte Register (offset: Read = 13h; Write = 13h) [reset =
00h]
Figure 31. Remote Temperature High Limit Low Byte Register
7
RTHL3
R/W-0h
6
RTHL2
R/W-0h
5
RTHL1
R/W-0h
4
RTHL0
R/W-0h
3
2
1
0
RESERVED
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 18. Remote Temperature High Limit Low Byte Register Field Descriptions
Bit
7-4
Field
Type
Reset
Description
RTHL3 - RTHL0
R/W
0h
These bits determine the value of the low byte of the high
temperature limit to which the remote temperature measurement
is compared. The resolution of the four bits in this register is
0.0625°C.
7.6.1.17 Remote Temperature Low Limit Low Byte Register (offset: Read = 14h; Write = 14h) [reset =
00h]
Figure 32. Remote Temperature Low Limit Low Byte Register
7
RTLL3
R/W-0h
6
RTLL2
R/W-0h
5
RTLL1
R/W-0h
4
RTLL0
R/W-0h
3
2
1
0
RESERVED
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 19. Remote Temperature Low Limit Low Byte Register Field Descriptions
Bit
7-4
24
Field
Type
Reset
Description
RTLL3 - RTLL0
R/W
0h
These bits determine the value of the low byte of the low
temperature limit to which the remote temperature measurement
is compared. The resolution of the four bits in this register is
0.0625°C.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
7.6.1.18 Local Temperature Low Byte Register (offset: Read = 15h; Write = N/A) [reset = 00h]
Figure 33. Local Temperature Low Byte Register
7
LT3
R-0h
6
LT2
R-0h
5
TL1
R-0h
4
LT0
R-0h
3
2
1
0
RESERVED
R-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 20. Local Temperature Low Byte Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
LT3 - LT0
R
0h
Local temperature low byte. The resolution of the four bits in this
register is 0.0625C.
This register is read-only and is updated by the ADC each time
a temperature measurement is completed. When the full
temperature value is needed, reading the high byte register first
causes the low byte register value to be locked (the ADC does
not write to it) until it is read. The same thing happens upon
reading the low byte register value first (the high byte register
value is locked until it is read). This mechanism assures that
both bytes of the read operation are from the same ADC
conversion. This assurance remains valid only until another
register is read. For proper operation, read the high byte of the
temperature result first. Read the low byte register in the next
read command; if the low byte is not needed, the register may
be left unread.
7.6.1.19 Remote Temperature THERM Limit Register (offset: Read = 19h; Write = 19h) [reset = 6C]
Figure 34. Remote Temperature THERM Limit Register
7
RTH11
R/W-0h
6
RTH10
R/W-1h
5
RTH9
R/W-1h
4
RTH8
R/W-0h
3
RTH7
R/W-1h
2
RTH6
R/W-1h
1
RTH5
R/W-0h
0
RTH4
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 21. Remote Temperature THERM Limit Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
RTH11 - RTH4
R/W
6Ch
Remote temperature THERM limit. These bits determine the
value of the THERM limit to which the remote temperature
measurement is compared. The resolution of the LSB in this
register is 1 °C.
7.6.1.20 Local Temperature THERM Limit Register (offset: Read = 20h; Write = 20h) [reset = 55]
Figure 35. Local Temperature THERM Limit Register
7
LTH11
R/W-0h
6
LTH10
R/W-1h
5
LTH9
R/W-0h
4
LTH8
R/W-1h
3
LTH7
R/W-0h
2
LTH6
R/W-1h
1
LTH5
R/W-0h
0
LTH4
R/W-1h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 22. Local Temperature THERM Limit Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
LTH11 - LTH4
R/W
55h
Local temperature THERM limit. These bits determine the value
of the THERM limit to which the local temperature measurement
is compared. The resolution of the LSB in this register is 1 °C.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
25
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
7.6.1.21 THERM Hysteresis Register (offset: Read = 21h; Write = 21h) [reset = 0Ah]
Figure 36. THERM Hysteresis Register
7
HYS11
R/W-0h
6
HYS10
R/W-0h
5
HYS9
R/W-0h
4
HYS8
R/W-0h
3
HYS7
R/W-1h
2
HYS6
R/W-0h
1
HYS5
R/W-1h
0
HYS4
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 23. THERM Hysteresis Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
HYS11 - HYS4
R/W
0Ah
THERM hysteresis value. These bits determine the amount of
hysteresis applied to the THERM function. The rsolution of the
LSB in this register is 1 °C.
7.6.1.22 Consecutive ALERT Register (offset: Read = 22h; Write = 22h) [reset = 01h]
Figure 37. Consecutive ALERT Register
7
SMBTO
R/W-0h
6
5
RESERVED
R/W-0h
4
3
CONAL2
R/W-0h
2
CONAL1
R/W-0h
1
CONAL0
R/W-0h
0
RESERVED
R/W-1h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 24. Consecutive ALERT Register Field Descriptions
Bit
7
3-1
Field
Type
Reset
Description
SMBTO
R/W
0h
SMBus time-out enable or disable. Refer to Time-out Function
1 = Enables the SMBus time-out feature.
0 = Disables the SMBus time-out feature.
CONAL2 - CONAL1
R/W
0h
Number of consecutive out-of-limit measurements required to
activate the ALERT flag and pin
Refer to Table 25
Table 25. Consecutive Alert Configuration
VALUE
Number of Consecutive Out-of-limit Measurements Required
0h
1
1h
2
3h
3
7h
4
7.6.1.23 η-Factor Correction Register (offset: Read = 23h; Write = 23h) [reset = 00h]
Figure 38. η-Factor Correction Register
7
NC7
R/W-0h
6
NC6
R/W-0h
5
NC5
R/W-0h
4
NC4
R/W-0h
3
NC3
R/W-0h
2
NC2
R/W-0h
1
NC1
R/W-0h
0
NC0
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 26. η-Factor Correction Register Field Descriptions
Bit
7-0
26
Field
Type
Reset
Description
NC7 - NC0
R/W
00h
η-factor value
Refer to Table 27
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
The TMP451 device allows for a different η-factor value to be used for converting remote channel measurements
to temperature. The remote channel uses sequential current excitation to extract a differential VBE voltage
measurement to determine the temperature of the remote transistor. Equation 1 shows this voltage and
temperature.
VBE2 - VBE1 =
hkT
I
ln 2
q
I1
(1)
The value η in Equation 1 is a characteristic of the particular transistor used for the remote channel. The poweron reset value for the TMP451 device is η = 1.008. The value in the η-factor correction register may be used to
adjust the effective η-factor according to Equation 2 and Equation 3.
eff
§ 1.008 u 2088 ·
¨
¸
© 2088 NADJUST ¹
NADJUST
(2)
§ 1.008 u 2088 ·
¨
¸ 2088
eff
©
¹
(3)
The η-factor correction value must be stored in twos complement format, yielding an effective data range from
–128 to 127. The η-factor correction value is written to and read from pointer address 23h. The register power-on
reset value is 00h, thus having no effect unless a different value is written to it.
Table 27. η-Factor Range
NADJUST
BINARY
HEX
DECIMAL
η
0111 1111
7F
127
0.950198
0000 1010
0A
10
1.003195
0000 1000
08
8
1.004152
0000 0110
06
6
1.005111
0000 0100
04
4
1.006072
0000 0010
02
2
1.007035
0000 0001
01
1
1.007517
0000 0000
00
0
1.008
1111 1111
FF
–1
1.008483
1111 1110
FE
–2
1.008967
1111 1100
FC
–4
1.009935
1111 1010
FA
–6
1.010905
1111 1000
F8
–8
1.011877
1111 0110
F6
–10
1.012851
1000 0000
80
–128
1.073837
7.6.1.24 Digital Filter Control Register (offset: Read = 24h; Write = 24h) [reset = 00h]
Figure 39. Digital Filter Control Register
7
6
5
4
3
2
1
DF1
R/W-0h
RESERVED
R/W-0h
0
DF0
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 28. Digital Filter Control Register Field Descriptions
Bit
1-0
Field
Type
Reset
Description
DF1 - DF0
R/W
0h
Configures the amount of filtering for the remote temperature
results. Refer toTable 29
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
27
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
Table 29. Digital Filter Configuration
VALUE
Number of Remote Temperature Measurements Averaged
0h
Averaging off
1h
4
2h
8
4h
not used
7.6.1.25 Manufacturer ID Register (offset: Read = FEh; Write = N/A) [reset = 55]
Figure 40. Manufacturer ID Register
7
ID7
R-0h
6
ID6
R-1h
5
ID5
R-0h
4
ID4
R-1h
3
ID3
R-0h
2
ID2
R-1h
1
ID1
R-0h
0
ID0
R-1h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 30. Manufacturer ID Register Field Descriptions
Bit
7-0
Field
Type
Reset
Description
ID7 - ID0
R
55h
Manufacturer identification information
The TMP451 device allows for the two-wire bus controller to query the device for manufacturer and device IDs to
enable software identification of the device at the particular two-wire bus address. The manufacturer ID is
obtained by reading from pointer address FEh. The TMP451 device reads 55h for the manufacturer code.
28
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TMP451 device requires only a transistor connected between the D+ and D– pins for remote temperature
measurement. Tie the D+ pin to GND if the remote channel is not used and only the local temperature is
measured. The SDA, ALERT, and THERM pins (and SCL, if driven by an open-drain output) require pullup
resistors as part of the communication bus. A 0.1-µF power-supply decoupling capacitor is recommended for
local bypassing.
8.2 Typical Application
Figure 41 shows the typical configuration for the TMP451 device.
1.7 V to 3.6 V
1.7 V to 3.6 V
RS(2)
CDIFF(3)
RS(2)
0.1 µF
Diode-connected configuration(1)
10 k
(typ)
1
10 k
(typ)
10 k
(typ)
V+
Series Resistance
RS(2)
10 k
(typ)
2
8
D+
SCL
D
SDA
CDIFF(3)
RS(2)
7
3
SMBus
Controller
TMP451
4
THERM
Transistor-connected configuration
(1)
5
GND
ALERT / THERM2
6
Overtemperature Shutdown
(1) Diode-connected configuration provides better settling time. Transistor-connected configuration provides better series resistance
cancellation.
(2) RS (optional) should be < 1 kΩ in most applications. Selection of RS depends on application; see the Filtering section.
(3) CDIFF (optional) should be < 1000 pF in most applications. Selection of CDIFF depends on application; see the Filtering section and
Figure 6.
Figure 41. TMP451 Basic Connections Using a Discrete Remote Transistor
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
29
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
Typical Application (continued)
1.7V to 3.6V
1.7V to 3.6V
1
V+
Processor or
ASIC
Built-in Thermal
Transistor/Diode
2
8
DXP
SCL
DXN
SDA
7
3
TMP451
SMBus
Controller
4
THERM
5
GND
ALERT / THERM2
6
Overtemperature Shutdown
Figure 42. TMP451 Basic Connections Using a Processor Built-In Remote Transistor
8.2.1 Design Requirements
The TMP451 device is designed to be used with either discrete transistors or substrate transistors built into
processor chips and ASICs. Either NPN or PNP transistors can be used, as long as the base-emitter junction is
used as the remote temperature sense. NPN transistors must be diode-connected. PNP transistors can either be
transistor- or diode-connected (see Figure 41).
Errors in remote temperature sensor readings are typically the consequence of the ideality factor and current
excitation used by the TMP451 device versus the manufacturer-specified operating current for a given transistor.
Some manufacturers specify a high-level and low-level current for the temperature-sensing substrate transistors.
The TMP451 device uses 7.5 μA for ILOW and 120 μA for IHIGH.
The ideality factor (η) is a measured characteristic of a remote temperature sensor diode as compared to an
ideal diode. The TMP451 allows for different η-factor values; see the η-Factor Correction Register section.
The ideality factor for the TMP451 device is trimmed to be 1.008. For transistors that have an ideality factor that
does not match the TMP451, Equation 4 can be used to calculate the temperature error.
NOTE
For the equation to be used correctly, actual temperature (°C) must be converted to Kelvin
(K).
TERR =
h - 1.008
´ (273.15 + T(°C))
1.008
where
•
•
•
•
30
TERR = error in the TMP451 device because η ≠ 1.008
η = ideality factor of remote temperature sensor
T(°C) = actual temperature
Degree delta is the same for °C and K.
Submit Documentation Feedback
(4)
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
Typical Application (continued)
For η = 1.004 and T(°C) = 100°C:
ǒ
Ǔ
T ERR + 1.004 * 1.008
1.008
ǒ273.15 ) 100°CǓ
T ERR + 1.48°C
(5)
If a discrete transistor is used as the remote temperature sensor with the TMP451, the best accuracy can be
achieved by selecting the transistor according to the following criteria:
1. Base-emitter voltage > 0.25 V at 7.5 μA, at the highest sensed temperature.
2. Base-emitter voltage < 0.95 V at 120 μA, at the lowest sensed temperature.
3. Base resistance < 100 Ω.
4. Tight control of VBE characteristics indicated by small variations in hFE (that is, 50 to 150).
Based on this criteria, two recommended small-signal transistors are the 2N3904 (NPN) or 2N3906 (PNP).
8.2.2 Detailed Design Procedure
The local temperature sensor inside the TMP451 device monitors the ambient air around the device. The thermal
time constant for the TMP451 device is approximately two seconds. This constant implies that if the ambient air
changes quickly by 100°C, it would take the TMP451 device about 10 seconds (that is, five thermal time
constants) to settle to within 1°C of the final value. In most applications, the TMP451 package is in electrical, and
therefore thermal, contact with the printed circuit board (PCB), as well as subjected to forced airflow. The
accuracy of the measured temperature directly depends on how accurately the PCB and forced airflow
temperatures represent the temperature that the TMP451 is measuring. Additionally, the internal power
dissipation of the TMP451 can cause the temperature to rise above the ambient or PCB temperature. The
internal power dissipated as a result of exciting the remote temperature sensor is negligible because of the small
currents used. For a 3.3-V supply and maximum conversion rate of 16 conversions per second, the TMP451
device dissipates 0.54 mW (PDIQ = 3.3 V × 165 μA). A θJA of 171.3°C/W causes the junction temperature to rise
approximately 0.09°C above the ambient.
The temperature measurement accuracy of the TMP451 device depends on the remote and/or local temperature
sensor being at the same temperature as the system point being monitored. Clearly, if the temperature sensor is
not in good thermal contact with the part of the system being monitored, then there will be a delay in the
response of the sensor to a temperature change in the system. For remote temperature-sensing applications
using a substrate transistor (or a small, SOT23 transistor) placed close to the device being monitored, this delay
is usually not a concern.
8.2.3 Application Curves
The following curves show the performance capabilities of the TMP451 device. Figure 43 shows the accuracy
performance in an oil-bath temperature drift of a population of 16 standrard 2N3906 transistors measured in a
diode-connected configuration. Figure 44 shows the typical step response to a submerging of a sensor in an oil
bath with temperature of 100°C.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
31
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
Typical Application (continued)
2
Mean
Mean 66
Mean + 66
1
Temperature (C)
Temperature Error ((qC))
1.5
0.5
0
-0.5
-1
-1.5
-2
-40
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
±1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
-25
-10
5
20 35 50 65 80 95
Remote Diode Temperature (qC)
110 125
D001
Figure 43. TMP451 Remote Diode Temperature Drift
(Diode-Connected 2N3906)
Time (s)
C007
Figure 44. Temperature Step Response
9 Power Supply Recommendations
The TMP451 device operates with a power supply range of 1.7 V to 3.6 V. The device is optimized for operation
at 3.3-V supply but can measure temperature accurately in the full supply range.
A power-supply bypass capacitor is recommended. Place this capacitor as close as possible to the supply and
ground pins of the device. A typical value for this supply bypass capacitor is 0.1 μF. Applications with noisy or
high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise.
10 Layout
10.1 Layout Guidelines
Remote temperature sensing on the TMP451 device measures very small voltages using very low currents;
therefore, noise at the device inputs must be minimized. Most applications using the TMP451 have high digital
content, with several clocks and logic level transitions creating a noisy environment. Layout should adhere to the
following guidelines:
1. Place the TMP451 device as close to the remote junction sensor as possible.
2. Route the D+ and D– traces next to each other and shield them from adjacent signals through the use of
ground guard traces; see Figure 45. If a multilayer PCB is used, bury these traces between ground or V+
planes to shield them from extrinsic noise sources. 5 mil (0.127 mm) PCB traces are recommended.
3. Minimize additional thermocouple junctions caused by copper-to-solder connections. If these junctions are
used, make the same number and approximate locations of copper-to-solder connections in both the D+ and
D– connections to cancel any thermocouple effects.
4. Use a 0.1μF local bypass capacitor directly between the V+ and GND of the TMP451 device. For optimum
measurement performance, minimize filter capacitance between D+ and D– to 1000 pF or less . This
capacitance includes any cable capacitance between the remote temperature sensor and the TMP451
device.
5. If the connection between the remote temperature sensor and the TMP451 device is less than 8-in (20,32
cm) long, use a twisted-wire pair connection. For lengths greater than 8 in, use a twisted, shielded pair with
the shield grounded as close to the TMP451 device as possible. Leave the remote sensor connection end of
the shield wire open to avoid ground loops and 60-Hz pickup.
6. Thoroughly clean and remove all flux residue in and around the pins of the TMP451 device to avoid
temperature offset readings as a result of leakage paths between D+ and GND, or between D+ and V+.
32
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
TMP451
www.ti.com
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
V+
D+
Ground or V+ layer
on bottom and/or
top, if possible.
D-
GND
Use minimum 5-mil (0.127 mm) traces with 5-mil spacing.
Figure 45. Suggested PCB Layer Cross-Section
10.2 Layout Example
VIA to Power or Ground Plane
VIA to Internal Layer
Pull-Up Resistors
Ground Plane
Supply Voltage
Supply Bypass
Capacitor
RS
1
V+
SCL
8
2
D+
SDA
7
3
D-
ALERT /
THERM2
6
CDIFF
RS
4
THERM
Thermal
Shutdown
GND 5
Serial Bus Traces
Figure 46. TMP451 Layout Example
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
33
TMP451
SBOS686A – JUNE 2013 – REVISED DECEMBER 2014
www.ti.com
11 Device and Documentation Support
11.1 Trademarks
SMBus is a trademark of Intel Corporation.
All other trademarks are the property of their respective owners.
11.2 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
34
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TMP451
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TMP451AIDQFR
ACTIVE
WSON
DQF
8
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
T451
TMP451AIDQFT
ACTIVE
WSON
DQF
8
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
T451
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
