TRS3318E
www.ti.com
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
Check for Samples: TRS3318E
FEATURES
DESCRIPTION
•
The TRS3318E is a dual-driver, dual-receiver, RS232-compatible transceiver. The device features
auto-powerdown plus and enhanced electrostatic
discharge (ESD) protection integrated into the chip.
Driver output and receiver input are protected to ±15
kV using the IEC 61000-4-2 Air-Gap Discharge
method, ±8 kV using the IEC 61000-4-2 Contact
Discharge method, and ±15 kV using the HumanBody Model (HBM).
1
•
•
•
•
•
•
ESD Protection for RS-232 I/O Pins
– ±15 kV (Human-Body Model)
– ±8 kV (IEC 61000-4-2, Contact Discharge)
– ±15 kV (IEC 61000-4-2, Air-Gap Discharge)
300-µA Operating Supply Current
1-µA Low-Power Standby Mode (With
Receivers Active)
Designed to Transmit at a Data Rate of
460 kbps
Auto-Powerdown Plus Option Features
Flexible Power-Saving Mode
Operates From a Single 2.25-V to 3-V VCC
Supply
Designed to be Interchangeable With Industry
Standard '3318 Devices
The device operates at a data rate of 460 kbps. The
transceiver has a proprietary low-dropout driver
output stage, enabling RS-232-compatible operation
from a 2.25-V to 3-V supply with a dual charge pump.
The charge pump requires only four 0.1-µF
capacitors and features a logic-level output (READY)
that asserts when the charge pump is regulating and
the device is ready to begin transmitting.
The TRS3318E achieves a 1-µA supply current using
the
auto-powerdown
feature.
This
device
automatically enters a low-power power-down mode
when the RS-232 cable is disconnected or the drivers
of the connected peripherals are inactive for more
than 30 s. The device turns on again when it senses
a valid transition at any driver or receiver input. Autopowerdown saves power without changes to the
existing BIOS or operating system.
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Cellular Phones
Notebooks
Hand-Held Equipment
Pagers
This device is available in two space-saving
packages: 20-pin SSOP and 20-pin TSSOP.
DB OR PW PACKAGE
(TOP VIEW)
READY
C1+
V+
C1−
C2+
C2−
V−
DOUT2
RIN2
ROUT2
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
FORCEOFF
VCC
GND
DOUT1
RIN1
ROUT1
FORCEON
DIN1
DIN2
INVALID
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2013, Texas Instruments Incorporated
TRS3318E
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
DETAILED DESCRIPTION
Flexible control options for power management are featured when the serial port and driver inputs are inactive.
The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense valid signal transitions on all receiver and driver inputs for approximately
30 s, the built-in charge pump and drivers are powered down, reducing the supply current to 1 µA. By
disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus can be disabled when
FORCEON and FORCEOFF are high. With auto-powerdown plus enabled, the device activates automatically
when a valid signal is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input
voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 µs
(typical number). INVALID is low (invalid data) if all receiver input voltage are between –0.3 V and 0.3 V for more
than 30 µs (typical number).
FUNCTION TABLE (1)
INPUT CONDITIONS
FORCEON
FORCEOFF
RECEIVER
OR DRIVER
EDGE
WITHIN 30 s
OUTPUT STATES
VALID
RS-232
LEVEL
PRESENT AT
RECEIVER
DRIVER
RECEIVER
INVALID
READY
OPERATING
MODE
Auto-Powerdown Plus Conditions
H
H
No
No
Active
Active
L
H
Normal operation,
auto-powerdown
plus disabled
H
H
No
Yes
Active
Active
H
H
Normal operation,
auto-powerdown
plus disabled
L
H
Yes
No
Active
Active
L
H
Normal operation,
auto-powerdown
plus enabled
L
H
Yes
Yes
Active
Active
H
H
Normal operation,
auto-powerdown
plus enabled
L
H
No
No
Z
Active
L
L
Power down,
auto-powerdown
plus enabled
L
H
No
Yes
Z
Active
H
L
Power down,
auto-powerdown
plus enabled
X
L
X
No
Z
Active
L
L
Manual power
down
X
L
X
Yes
Z
Active
H
L
Manual power
down
Auto-Powerdown Conditions
(1)
2
INVALID
INVALID
X
No
Z
Active
L
L
Power down,
auto-powerdown
enabled
INVALID
INVALID
X
Yes
Active
Active
H
H
Normal operation,
auto-powerdown
enabled
H = high level, L = low level, X = irrelevant, Z = high impedance
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
TRS3318E
www.ti.com
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
LOGIC DIAGRAM (POSITIVE LOGIC)
DIN1
DIN2
FORCEOFF
FORCEON
ROUT1
13
17
12
8
20
11
14
Auto-powerdown Plus
15
DOUT1
DOUT2
INVALID
1
READY
16
RIN1
5 kΩ
ROUT2
10
9
RIN2
5 kΩ
TERMINAL FUNCTIONS
TERMINAL
NAME
DESCRIPTION
NO.
C1+
2
Positive voltage-doubler charge-pump capacitor
C1–
4
Negative voltage-doubler charge-pump capacitor
C2+
5
Positive inverting charge-pump capacitor
C2–
6
Negative inverting charge-pump capacitor
DIN
12, 13
CMOS driver inputs
DOUT
8, 17
RS-232 driver outputs
FORCEOFF
20
Force-off input, active low. Drive low to power down transmitters and charge pump. This overrides autopowerdown and FORCEON (see Function Table).
FORCEON
14
Force-on input, active high. Drive high to override auto-powerdown, keeping transmitters on (FORCEOFF must
be high) (see Function Table).
GND
18
Ground
INVALID
11
Valid signal detector output, active low. A logic high indicates that a valid RS-232 level is present on a receiver
input.
READY
1
Ready to transmit output, active high. READY is enabled high when V– goes below –3.5 V and the device is
ready to transmit.
RIN
9, 16
RS-232 receiver inputs
ROUT
10, 15
CMOS receiver outputs
V+
3
2 × VCC generated by the charge pump
V–
7
–2 × VCC generated by the charge pump
VCC
19
2.25-V to 3-V single-supply voltage
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
3
TRS3318E
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
www.ti.com
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC to GND
–0.3
6
V
V+ to GND (2)
–0.3
7
V
V– to GND (2)
–7
0.3
V
13
V
V+ + IV–I (2)
Input voltage
Output voltage
Short-circuit duration
Continuous power dissipation (TA = 70°C)
DIN, FORCEON, FORCEOFF to GND
–0.3
6
RIN to GND
DOUT to GND
±13.2
ROUT, INVALID, READY to GND
–0.3
DOUT to GND
V
VCC + 0.3
Continuous
20-pin SSOP (derate 8 mW/°C above 70°C)
640
20-pin TSSOP (derate 7 mW/°C above 70°C)
559
–65
Lead temperature (soldering, 10 s)
(2)
V
±25
Storage temperature range
(1)
UNIT
mW
150
°C
300
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
V+ and V– can have maximum magnitudes of 7 V, but their absolute difference cannot exceed 13 V.
Recommended Operating Conditions
See Figure 4
MIN NOM
Supply voltage
2.25
VIH
Driver and control high-level input voltage
DIN, FORCEOFF,
FORCEON
VIL
Driver and control low-level input voltage
DIN, FORCEOFF,
FORCEON
VI
Receiver input voltage
TA
Operating free-air temperature
4
VCC = 2.5 V to 3 V
VCC = 2.5 V to 3 V
TRS3318EC
TRS3318EI
Submit Documentation Feedback
2.5
MAX UNIT
3
V
0.7 × VCC
5.5
V
0
0.3 × VCC
V
–25
25
V
0
70
–40
85
°C
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
TRS3318E
www.ti.com
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
Supply Current Section
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1) MAX
UNIT
DC Characteristics (VCC = 2.5 V, TA = 25°C)
Auto-powerdown plus supply current
FORCEON = GND, FORCEOFF = VCC, All RIN and DIN idle
Auto-powerdown supply current
FORCEOFF = GND
Supply current
FORCEON = FORCEOFF = VCC, No load
(1)
1
10
µA
1
10
µA
0.3
2
mA
Typical values are at VCC = 2.5 V, TA = 25°C.
ESD Protection
PARAMETER
RIN, DOUT
TEST CONDITIONS
TYP
HBM
±15
IEC 61000-4-2 Air-Gap Discharge method
±15
IEC 61000-4-2 Contact Discharge method
±8
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
UNIT
kV
5
TRS3318E
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
www.ti.com
Driver Section
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
MIN TYP (1)
TEST CONDITIONS
Driver input hysteresis
MAX
0.3
±0.01
UNIT
V
Input leakage current
FORCEON, DIN, FORCEOFF
Output voltage swing
All driver outputs loaded with 3 kΩ to ground
±3.7
±4
V
Output resistance
VCC = 0, Driver output = ±2 V
300
10M
Ω
Output short-circuit current (2)
Output leakage current
(1)
(2)
±25
VCC = 0 or 2.25 V to 3 V, VOUT = ±12 V, Drivers disabled
±1
µA
±60
mA
±25
µA
Typical values are at VCC = 2.5 V, TA = 25°C.
Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 1)
PARAMETER
Maximum data rate
TEST CONDITIONS
MIN
RL = 3 kΩ, CL = 1000 pF, One transmitter switching
(1)
(2)
6
MAX
460
|tPHL – tPLH| Driver skew (2)
Transition-region slew rate
TYP (1)
kbps
100
VCC = 2.5 V, TA = 25°C, RL = 3 kΩ to 7 kΩ,
Measured from 3 V to –3 V or –3 V to 3 V,
CL = 150 pF to 2500 pF
4
UNIT
ns
30
V/µs
Typical values are at VCC = 2.5 V, TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
TRS3318E
www.ti.com
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
Receiver Section
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
MIN TYP (1)
TEST CONDITIONS
Input voltage range
–25
Input threshold low
TA = 25°C
Input threshold high
TA = 25°C
V
0.3 × VCC
V
V
0.3
Input resistance
TA = 25°C
3
Output leakage current
5
±0.05
Output voltage low
IOUT = 0.5 mA
Output voltage high
IOUT = –0.5 mA
UNIT
25
0.7 × VCC
Input hysteresis
(1)
MAX
V
7
kΩ
±10
µA
0.1 × VCC
V
0.9 × VCC
V
Typical values are at VCC = 2.5 V, TA = 25°C.
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF (unless otherwise noted) (see Figure 4)
PARAMETER
tPHL
Receiver propagation delay
tPLH
|tPHL – tPLH|
(1)
(2)
TEST CONDITIONS
RIN to ROUT, CL = 150 pF
Receiver skew (2)
TYP (1)
0.175
0.175
50
UNIT
µs
ns
Typical values are at VCC = 2.5 V, TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
7
TRS3318E
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
www.ti.com
Auto-Powerdown Plus Section
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
MAX
Positive threshold
Receiver input threshold to INVALID high
2.7
Negative threshold
–2.7
Receiver input threshold INVALID low
–0.3
INVALID, READY voltage low
IOUT = 0.5 mA
INVALID, READY voltage high
IOUT = –0.5 mA
UNIT
V
0.3
V
0.1 × VCC
V
0.8 × VCC
V
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
tINVH
Receiver positive or negative threshold to INVALID high
VCC = 2.5 V
1
µs
tINVL
Receiver positive or negative threshold to INVALID low
VCC = 2.5 V
30
µs
tWU
Receiver or driver edge to driver enabled
VCC = 2.5 V
100
µs
tAUTOPRDN
Receiver or driver edge to driver shutdown
VCC = 2.5 V
(1)
8
15
30
60
s
Typical values are at VCC = 2.5 V, TA = 25°C.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
TRS3318E
www.ti.com
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
PARAMETER MEASUREMENT INFORMATION
3V
Generator
(see Note B)
Input
RS-232
Output
50 Ω
RL
CL
(see Note A)
3V
FORCEOFF
TEST CIRCUIT
0V
tTLH
tTHL
Output
6V
SR(tr) +
t THL or tTLH
VOH
3V
3V
−3 V
−3 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 1. Driver Slew Rate
2.25 V
Generator
(see Note B)
RS-232
Output
50 Ω
RL
Input
1.125 V
1.125 V
0V
CL
(see Note A)
tPLH
tPHL
VOH
3V
FORCEOFF
50%
50%
Output
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 2. Driver Pulse Skew
3V
Input
0V
0V
−3 V
Output
Generator
(see Note B)
tPHL
50 Ω
tPLH
CL
(see Note A)
VOH
50%
Output
50%
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 3. Receiver Propagation Delay Times
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
9
TRS3318E
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Receiver
Inputs
}
Invalid
Region
Driver
Inputs
Driver
Outputs
VCC
INVALID
Output
tINVL
tINVH
0
tWU
tWU
VCC
Ready
Output
0
V+
VCC
0
V−
VOLTAGE WAVEFORMS
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
Valid RS-232 Level, INVALID High
ROUT
Generator
(see Note B)
2.7 V
50 Ω
Indeterminate
0.3 V
0V
If Signal Remains Within This Region
For More Than 30 µs, INVALID Is Low†
−0.3 V
Auto-powerdown
Plus
Indeterminate
INVALID
−2.7 V
CL = 30 pF
(see Note A)
†
FORCEON
FORCEOFF
Valid RS-232 Level, INVALID High
DIN
DOUT
Auto-powerdown disables drivers and reduces supply
current to 1 µA.
TEST CIRCUIT
Figure 4. INVALID Propagation Delay Times and Supply Enabling Time
10
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
TRS3318E
www.ti.com
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
APPLICATION INFORMATION
2.5 V
+ 0.1 mF
19
CBYPASS
2
C1
0.1 mF
C2
0.1 mF
+
4
+
5
6
VCC
C1+
V+
3
+
C1−
V−
C2+
7
C2−
13 DIN1
DOUT1 17
12 DIN2
DOUT2 8
C4
+ 0.1 mF
RS-232-Compatible
Outputs
RS-232-Compatible
Inputs
RIN1 16
15 ROUT1
C3
0.1 mF
5k
10 ROUT2
1
RIN2 9
5k
READY
To Power-Management Unit
Autopowerdown INVALID 11
Plus
VCC
FORCEOFF 20
14
FORCEON
GND
18
Figure 5. Typical Application Circuit
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
11
TRS3318E
SLLS805B – APRIL 2007 – REVISED OCTOBER 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (April 2010) to Revision B
Page
•
Updated document to new TI datasheet format - no specification changes. ....................................................................... 1
•
Removed Ordering Information table. ................................................................................................................................... 2
•
Updated TERMINAL FUNCTIONS table to fix inconsistency. .............................................................................................. 3
12
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: TRS3318E
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TRS3318ECDBR
ACTIVE
SSOP
DB
20
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
RV18EC
Samples
TRS3318ECPW
ACTIVE
TSSOP
PW
20
70
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
RV18EC
Samples
TRS3318ECPWR
ACTIVE
TSSOP
PW
20
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
RV18EC
Samples
TRS3318EIDBR
ACTIVE
SSOP
DB
20
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
RV18EI
Samples
TRS3318EIPW
ACTIVE
TSSOP
PW
20
70
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
RV18EI
Samples
TRS3318EIPWR
ACTIVE
TSSOP
PW
20
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
RV18EI
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
