CAT522_04

CAT522 Configured Digitally Programmable Potentiometer (DPP™): Programmable Voltage Applications H GEN FR ALO EE LE FEATURES s Two 8-bit DPPs configured as programmable A D F R E ETM APPLICATIONS s Automated product calibration. s Remote control adjustment of equipment s Offset, gain and zero adjustments in self- voltage sources in DAC-like applications s Independent reference inputs s Non-volatile NVRAM memory wiper storage s Output voltage range includes both supply rails s 2 independently addressable buffered calibrating and adaptive control systems. s Tamper-proof calibrations. s DAC (with memory) substitute. output wipers s 1 LSB accuracy, high resolution s Serial Microwire-like interface s Single supply operation: 2.7V - 5.5V s Setting read-back without effecting outputs DESCRIPTION The CAT522 is a dual, 8-bit digitally-programmable potentiometer (DPP™) configured for programmable voltage and DAC-like applications. Intended for final calibration of products such as camcorders, fax machines and cellular telephones on automated high volume production lines, it is also well suited for self-calibrating systems and for applications where equipment which requires periodic adjustment is either difficult to access or in a hazardous environment. The CAT522 offers two independently programmable DPPs each having its own reference inputs and each capable of rail to rail output swing. The wipers are buffered by rail to rail opamps. Wiper settings, stored in non-volatile NVRAM memory, are not lost when the device is powered down and are automatically reinstated when power is returned. Each wiper can be FUNCTIONAL DIAGRAM RDY/BSY V DD VREFH1 VREFH2 14 13 dithered to test new output values without effecting the stored settings and stored settings can be read back without disturbing the DPP's output. The CAT522 is controlled with a simple 3-wire, microwirelike serial interface. A Chip Select pin allows several devices to share a common serial interface. Communication back to the host controller is via a single serial data line thanks to the CAT522 Tri-Stated Data Output pin. A RDY/BSY output working in concert with an internal low voltage detector signals proper operation of the non-volatile NVRAM memory Erase/Write cycle. The CAT522 is available in the 0°C to 70°C commercial and -40°C to 85°C industrial operating temperature ranges. Both 14-pin plastic DIP and surface mount packages are available. PIN CONFIGURATION DIP Package (P, L) VDD CLK 1 2 3 4 5 6 7 CAT522 SOIC Package (J, W) VDD CLK 1 2 3 4 5 6 7 CAT522 3 1 PROG 7 PROGRAM CONTROL 14 13 12 11 10 9 8 VREFH1 VREFH2 14 13 12 11 10 9 8 VREFH1 VREFH2 VOUT1 VOUT2 VREFL2 VREFL1 GND DI 5 WIPER CONTROL REGISTERS AND NVRAM 24kΩ + 24KΩ 11 V OUT2 RDY/BSY CS CLK 2 SERIAL CONTROL VOUT1 RDY/BSY VOUT2 VREFL2 VREFL1 GND CS DI DO PROG CS 4 + 12 V OUT1 DI DO SERIAL DATA OUTPUT REGISTER 6 DO PROG CAT522 8 GND 9 10 VREFL1 VREFL2 © 2004 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 1 Doc. No. 2004, Rev. E CAT522 ABSOLUTE MAXIMUM RATINGS Supply Voltage* VDD to GND ...................................... -0.5V to +7V Inputs CLK to GND ............................ -0.5V to VDD +0.5V CS to GND .............................. -0.5V to VDD +0.5V DI to GND ............................... -0.5V to VDD +0.5V RDY/BSY to GND ................... -0.5V to VDD +0.5V PROG to GND ........................ -0.5V to VDD +0.5V VREFH to GND ........................ -0.5V to VDD +0.5V VREFL to GND ......................... -0.5V to VDD +0.5V Outputs D0 to GND ............................... -0.5V to VDD +0.5V VOUT 1– 4 to GND ................... -0.5V to VDD +0.5V RELIABILITY CHARACTERISTICS Symbol VZAP(1) ILTH(1)(2) Operating Ambient Temperature Commercial (‘C’ or Blank suffix) ...... 0°C to +70°C Industrial (‘I’ suffix) ........................ -40°C to +85°C Junction Temperature ..................................... +150°C Storage Temperature ........................ -65°C to +150°C Lead Soldering (10 sec max) .......................... +300°C * Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Absolute Maximum Ratings are limited values applied individually while other parameters are within specified operating conditions, and functional operation at any of these conditions is NOT implied. Device performance and reliability may be impaired by exposure to absolute rating conditions for extended periods of time. Parameter ESD Susceptibility Latch-Up Min 2000 100 Max Units Volts mA Test Method MIL-STD-883, Test Method 3015 JEDEC Standard 17 NOTES: 1. This parameter is tested initially and after a design or process change that affects the parameter. 2. Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to VCC + 1V. POWER SUPPLY Symbol Parameter IDD1 IDD2 Supply Current (Read) Supply Current (Write) Conditions Normal Operating Programming, VDD = 5V VDD = 3V VDD Operating Voltage Range Min — — — 2.7 Typ 400 1600 1000 — Max 600 2500 1600 5.5 Units µA µA µA V LOGIC INPUTS Symbol IIH IIL VIH VIL Parameter Input Leakage Current Input Leakage Current High Level Input Voltage Low Level Input Voltage Conditions VIN = VDD VIN = 0V Min — — 2 0 Typ — — — — Max 10 -10 VDD 0.8 Units µA µA V V LOGIC OUTPUTS Symbol Parameter VOH VIL High Level Output Voltage Low Level Output Voltage Conditions IOH = -40µA IOL = 1 mA, VDD = +5V IOL = 0.4 mA, VDD = +3V Min VDD -0.3 — — Typ — — — Max — 0.4 0.4 Units V V V Doc. No. 2004, Rev. E 2 CAT522 POTENTIOMETER CHARACTERISTICS VDD = +2.7V to +5.5V, VREFH = VDD, VREFL = 0V, unless otherwise specified Symbol RPOT Parameter Potentiometer Resistance RPOT to RPOT Match Pot Resistance Tolerance Voltage on VREFH pin Voltage on VREFL pin Resolution INL DNL ROUT IOUT TCRPOT CH/CL Integral Linearity Error Differential Linearity Error Buffer Output Resistance Buffer Output Current TC of Pot Resistance Potentiometer Capacitances 300 8/8 2.7 0V 0.4 0.5 0.25 1 0.5 10 3 — Conditions Min Typ 24 +0.5 +1 +20 VDD VDD - 2.7 Max Units kΩ % % V V % LSB LSB Ω mA ppm/˚C pF AC ELECTRICAL CHARACTERISTICS: VDD = +2.7V to +5.5V, VREFH = VDD, VREFL = 0V, unless otherwise specified Symbol Digital tCSMIN tCSS tCSH tDIS tDIH tDO1 tDO0 tHZ tLZ tBUSY tPS tPROG tCLKH tCLKL fC Minimum CS Low Time CS Setup Time CS Hold Time DI Setup Time DI Hold Time Output Delay to 1 Output Delay to 0 Output Delay to High-Z Output Delay to Low-Z Erase/Write Cycle Time PROG Setup Time Minimum Pulse Width Minimum CLK High Time Minimum CLK Low Time Clock Frequency DPP Settling Time to 1 LSB 150 100 0 50 50 — — — — — 150 700 500 300 DC — — — — — — — — — 400 400 4 — — — — — 3 6 — — — — — 150 150 — — 5 — — — — 1 10 10 ns ns ns ns ns ns ns ns ns ms ns ns ns ns MHz µs µs Parameter Conditions Min Typ Max Units CL=100pF, see note 1 Analog tDS CLOAD = 10 pF, VDD = +5V CLOAD = 10 pF, VDD = +3V NOTES: 1. All timing measurements are defined at the point of signal crossing VDD / 2. 2. These parameters are periodically sampled and are not 100% tested. 3 Doc. No. 2004, Rev. E CAT522 A. C. TIMING DIAGRAM to 1 2 3 4 5 t CLK H CLK t CSS CS t CLK L t CSH t CSMIN t DIS DI t DIH t LZ DO t DO0 t HZ t DO1 PROG t PS t PROG RDY/BSY t BUSY to 1 2 3 4 5 Doc. No. 2004, Rev. E 4 CAT522 PIN DESCRIPTION Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DPP addressing is as follows: Function Power supply positive Clock input pin Ready/Busy output Chip select Serial data input pin Serial data output pin EEPROM Programming Enable Input Power supply ground Minimum DPP 1 output voltage Minimum DPP 2 output voltage DPP 2 output DPP 1 output Maximum DPP 2 output voltage Maximum DPP 1 output voltage Name VDD CLK RDY/BSY CS DI DO PROG GND VREFL1 VREFL2 VOUT2 VOUT1 VREFH2 VREFH1 DPP OUTPUT VOUT1 VOUT2 A0 0 1 A1 1 1 DEVICE OPERATION The CAT522 is a dual 8-bit configured digitally programmable potentiometer (DPP) whose outputs can be programmed to any one of 256 individual voltage steps. Once programmed, these output settings are retained in non-volatile memory and will not be lost when power is removed from the chip. Upon power up the DPPs return to the settings stored in non-volatile memory. Each DPP can be written to and read from independently without effecting the output voltage during the read or write cycle. Each output can also be adjusted without altering the stored output setting, which is useful for testing new output settings before storing them in memory. DIGITAL INTERFACE The CAT522 employs a 3 wire serial, Microwire-like control interface consisting of Clock (CLK), Chip Select (CS) and Data In (DI) inputs. For all operations, address and data are shifted in LSB first. In addition, all digital data must be preceded by a logic “1” as a start bit. The DPP address and data are clocked into the DI pin on the clock’s rising edge. When sending multiple blocks of information a minimum of two clock cycles is required between the last block sent and the next start bit. Multiple devices may share a common input data line by selectively activating the CS control of the desired IC. Data Outputs (DO) can also share a common line because the DO pin is Tri-Stated and returns to a high impedance when not in use. CHIP SELECT Chip Select (CS) enables and disables the CAT522’s read and write operations. When CS is high data may be read to or from the chip, and the Data Output (DO) pin is active. Data loaded into the DPP control registers will remain in effect until CS goes low. Bringing CS to a logic low returns all DPP outputs to the settings stored in nonvolatile memory and switches DO to its high impedance Tri-State mode. Because CS functions like a reset the CS pin has been desensitized with a 30 ns to 90 ns filter circuit to prevent noise spikes from causing unwanted resets and the loss of volatile data. CLOCK The CAT522’s clock controls both data flow in and out of the IC and non-volatile memory cell programming. Serial data is shifted into the DI pin and out of the DO pin on the clock’s rising edge. While it is not necessary for the clock to be running between data transfers, the clock must be operating in order to write to non-volatile memory, even though the data being saved may already be resident in the DPP wiper control register. No clock is necessary upon system power-up. The CAT522’s internal power-on reset circuitry loads data from non-volatile memory to the DPPs without using the external clock. 5 Doc. No. 2004, Rev. E CAT522 As data transfers are edge triggered clean clock transitions are necessary to avoid falsely clocking data into the control registers. Standard CMOS and TTL logic families work well in this regard and it is recommended that any mechanical switches used for breadboarding or device evaluation purposes be debounced by a flip-flop or other suitable debouncing circuit. VREF VREF, the voltage applied between pins VREFH &VREFL, sets the configured DPP’s Zero to Full Scale output range where VREFL = Zero and VREFH = Full Scale. VREF can span the full power supply range or just a fraction of it. In typical applications VREFH &VREFL are connected across the power supply rails. When using less than the full supply voltage be mindful of the limits placed on VREFL and VREFL as specified in the References section of DC Electrical Characteristics. READY/BUSY When saving data to non-volatile memory, the Ready/ Busy ouput (RDY/BSY) signals the start and duration of the non-volatile erase/write cycle. Upon receiving a command to store data (PROG goes high) RDY/BSY goes low and remains low until the programming cycle is complete. During this time the CAT522 will ignore any data appearing at DI and no data will be output on DO. RDY/BSY is internally ANDed with a low voltage detector circuit monitoring VDD. If VDD is below the minimum value required for non-volatile programming, RDY/BSY will remain high following the program command indicating a failure to record the desired data in non-volatile memory. DATA OUTPUT Data is output serially by the CAT522, LSB first, via the Data Out (DO) pin following the reception of a start bit and two address bits by the Data Input (DI). DO becomes active whenever CS goes high and resumes its high impedance Tri-State mode when CS returns low. Tri-Stating the DO pin allows several 522s to share a Figure 1. Writing to Memory to 1 2 3 4 5 6 7 8 9 10 11 12 N N+1 N+2 single serial data line and simplifies interfacing multiple 522s to a microprocessor. WRITING TO MEMORY Programming the CAT522’s non-volatile memory is accomplished through the control signals: Chip Select (CS) and Program (PROG). With CS high, a start bit followed by a two bit DPP address and eight data bits are clocked into the DPP wiper control register via the DI pin. Data enters on the clock’s rising edge. The DPP output changes to its new setting on the clock cycle following D7, the last data bit. Programming is accomplished by bringing PROG high sometime after the start bit and at least 150 ns prior to the rising edge of the clock cycle immediately following the D7 bit. Two clock cycles after the D7 bit the DPP wiper control register will be ready to receive the next set of address and data bits. The clock must be kept running throughout the programming cycle. Internal control circuitry takes care of generating and ramping up the programming voltage for data transfer to the non-volatile cells. The CAT522’s non-volatile memory cells will endure over 1,000,000 write cycles and will retain data for a minimum of 100 years without being refreshed. READING DATA Each time data is transferred into a DPP control register currently held data is shifted out via the D0 pin, thus in every data transaction a read cycle occurs. Note, however, that the reading process is destructive. Data must be removed from the register in order to be read. Figure 2 depicts a Read Only cycle in which no change occurs in the DPP’s output. This feature allows µPs to poll DPPs for their current setting without disturbing the output voltage but it assumes that the setting being read is also stored in non-volatile memory so that it can be restored at the end of the read cycle. In Figure 2 CS returns low before the 13th clock cycle completes. In doing so the non-volatile memory setting is reloaded into the DPP wiper control register. Since this value is the Figure 2. Reading from Memory to 1 2 3 4 5 6 7 8 9 10 11 12 CS NEW DPP DATA DI 1 A0 A1 D0 D1 D2 D3 D4 D5 D6 D7 CS DI 1 A0 A1 CURRENT DPP DATA CURRENT DPP DATA DO D0 D1 D2 D3 D4 D5 D6 D7 DO D0 D1 D2 D3 D4 D5 D6 D7 PROG PROG RDY/BSY RDY/BSY DPP OUTPUT CURRENT DPP VALUE NON-VOLATILE NEW DPP VALUE VOLATILE NEW DPP VALUE NON-VOLATILE DPP OUTPUT CURRENT DPP VALUE NON-VOLATILE Doc. No. 2004, Rev. E 6 CAT522 same as that which had been there previously no change in the DPP’s output is noticed. Had the value held in the control register been different from that stored in nonvolatile memory then a change would occur at the read cycle’s conclusion. TEMPORARILY CHANGE OUTPUT The CAT522 allows temporary changes in DPP’s output to be made without disturbing the settings retained in non-volatile memory. This feature is particularly useful when testing for a new output setting and allows for user adjustment of preset or default values without losing the original factory settings. Figure 3 shows the control and data signals needed to effect a temporary output change. DPP wiper settings may be changed as many times as required and can be made to any of the two DPPs in any order or sequence. The temporary setting(s) remain in effect long as CS remains high. When CS returns low all two DPPs will return to the output values stored in non-volatile memory. When it is desired to save a new setting acquired using this feature, the new value must be reloaded into the DPP wiper control register prior to programming. This is because the CAT522’s internal control circuitry discards from the programming register the new data two clock cycles after receiving it if no PROG signal is received. APPLICATION CIRCUITS DPP INPUT +5V Vi Ri +15V VDD CONTROL & DATA VREFH RF Figure 3. Temporary Change in Output to 1 2 3 4 5 6 7 8 9 10 11 12 N N+1 N+2 CS NEW DPP DATA 1 A0 A1 D0 D1 D2 D3 D4 D5 D6 D7 DI CURRENT DPP DATA DO D0 D1 D2 D3 D4 D5 D6 D7 PROG RDY/BSY DPP OUTPUT CURRENT DPP VALUE NON-VOLATILE NEW DPP VALUE VOLATILE CURRENT DPP VALUE NON-VOLATILE DPP OUTPUT CODE VDPP = ——— (VFS - VZERO ) + V ZERO 255 VFS = 0.99 VREF VZERO = 0.01 V REF 255 —— (.98 VREF) + .01 VREF = .990 V REF 255 128 —— (.98 V ) + .01 V = .502 V REF REF REF 255 127 (.98 V —— ) + .01 V = .498 V 255 REF REF REF 1 —— (.98 V ) + .01 V = .014 V 255 REF REF REF 0 —— (.98 V ) + .01 V = .010 V REF REF REF 255 ANALOG OUTPUT MSB LSB 1111 – + OP 07 VOUT VREF = 5V R I = RF V OUT= +4.90V V V V = +0.02V = -0.02V = -4.86V 1111 CAT522 GND VREFL -15V 1000 0111 0000 1111 0001 OUT OUT OUT VOUT = V DPP ( R i+ RF) -Vi R F Ri For R i = RF VOUT = 2VDPP -Vi 0000 0000 0000 V OUT = -4.90V Bipolar DPP Output +5V RI +15V VDD CONTROL & DATA VREFH RF – + OP 07 VOUT CAT522 GND VREFL -15V RF VOUT = (1 + –––) V DPP RI Amplified DPP Output 7 Doc. No. 2004, Rev. E CAT522 APPLICATION CIRCUITS (Cont.) VREF RC = ————— 256 * 1 µA +5V VREF VREFH Fine adjust gives ± 1 LSB change in V OFFSET VREF when V OFFSET = ——— 2 127RC +5V +VREF VREFH VDD VDD FINE ADJUST DPP 127RC + (+VREF ) - (VOFFSET ) RC = ——————————— 1 µA FINE ADJUST DPP CAT522 COARSE ADJUST DPP RC CAT522 +V COARSE ADJUST DPP RC V OFFSET (-VREF ) + (VOFFSET+ ) Ro = ——————————— 1 µA + – GND VREFL Ro -VREF VOFFSET +V + – -V GND VREFL Coarse-Fine Offset Control by Averaging DPP Outputs for Single Power Supply Systems Coarse-Fine Offset Control by Averaging DPP Outputs for Dual Power Supply Systems 28 - 32V V+ 15K I > 2 mA 10 µF 1N5231B VDD CONTROL & DATA VREFH VREF = 5.000V CONTROL & DATA VDD VREFH 5.1V 10K CAT522 GND VREFL LT 1029 CAT522 GND VREFL + – LM 324 MPT3055EL OUTPUT 4.02 K 1.00K 10 µF 35V 0 - 25V @ 1A Digitally Trimmed Voltage Reference Digitally Controlled Voltage Reference Doc. No. 2004, Rev. E 8 CAT522 APPLICATION CIRCUITS (Cont.) +5V 2.2K VDD VREFH 4.7 µA LM385-2.5 +15V ISINK = 2 - 255 mA DPP +5V + – 10K 10K 2N7000 39 Ω 1W 39 Ω 1W 1 mA steps CONTROL & DATA CAT522 DPP + 2N7000 – 5 µA steps GND VREFL 5M 5M 3.9K 10K 10K – + TIP 30 -15V Current Sink with 4 Decades of Resolution +15V 51K + TIP 29 – 10K +5V 10K VDD VREFH 5M 5M 39 Ω 1W 39 Ω 1W DPP CONTROL & DATA CAT522 5M – + 5M BS170P 1 mA steps 3.9K DPP GND VREFL – BS170P + LM385-2.5 5 µA steps -15V ISOURCE = 2 - 255 mA Current Source with 4 Decades of Resolution 9 Doc. No. 2004, Rev. E CAT522 ORDERING INFORMATION Prefix CAT Device # 522 Suffix J I -TE13 Optional Company ID Product Number Package P: PDIP J: SOIC L: PDIP (Lead free, Halogen free) W: SOIC (Lead free, Halogen free) Tape & Reel TE13: 2000/Reel Temperature Range Blank = Commercial (0°C to 70°C) I = Industrial (-40°C to 85°C) Notes: (1) The device used in the above example is a CAT522JI-TE13 (SOIC, Industrial Temperature, Tape & Reel) Doc. No. 2004, Rev. E 10 CAT522 REVISION HISTORY Date 3/16/2004 7/12/2004 Rev. D E Reason Updated Potentiometer Characteristics Updated Functional Diagram Updated Potentiometer Characteristics Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP ™ AE2 ™ Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.catsemi.com 11 Publication #: Revison: Issue date: Type: 2004 E 7/12/04 Final Doc. No. 2004, Rev. E