A Business Partner of Renesas Electronics Corporation.
PS2933-1
Data Sheet
R08DS0115EJ0100
Rev.1.00
Nov 29, 2013
HIGH COLLECTOR TO EMITTER VOLTAGE
4-PIN ULTRA SMALL FLAT-LEAD
PHOTOCOUPLER
DESCRIPTION
The PS2933-1 is an optically coupled isolator containing a GaAs light emitting diode and an NPN silicon
phototransistor in one package for high density mounting applications.
An ultra small flat-lead package has been provided which realizes a reduction in mounting area of about 30% compared
with the PS28xx series.
FEATURES
•
•
•
•
•
Ultra small flat-lead package (4.6 (L) × 2.5 (W) × 2.1 (H) mm)
High collector to emitter voltage (VCEO = 350 V)
High isolation voltage (BV = 2 500 Vr.m.s.)
Ordering number of taping product: PS2933-1-F3: 3 500 pcs/reel
Safety standards
• UL approved: No. E72422
• BSI approved (BS EN 60065, BS EN 60950)
• DIN EN 60747-5-5 (VDE 0884-5) approved (Option)
APPLICATIONS
PIN CONNECTION
Top View
4
3
1. Anode
2. Cathode
3. Emitter
4. Collector
1
2
• Hybrid IC
• Telephone, Exchange equipment, FAX
The mark shows major revised points.
The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 1 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
PACKAGE DIMENSIONS (UNIT: mm)
2.5±0.3
4.6±0.2
4.1 MIN.
3
4
R
2
5.0±0.2
0.15 +0.1
–0.05
2.1 MAX.
1
0.4±0.1
0.2±0.1
1.27
MARKING EXAMPLE
Ni/Pd/Au PLATING
Last number of
type No. : 33
33
*1
R
Company initial
(Engraved R)
601
No. 1 pin
mark
(Nicked
corner)
Assembly lot
6 01
Week assembled
Year Assembled
(Last 1 Digit)
*1 Bar : Pb-Free
PHOTOCOUPLER CONSTRUCTION
Parameter
Air Distance
Creepage Distance
Isolation Distance
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
MIN.
4 mm
4 mm
0.4 mm
Page 2 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
ORDERING INFORMATION
Part Number
PS2933-1
PS2933-1-F3
PS2933-1-V
Order Number
Solder Plating
Specification
PS2933-1-AX
Pb-Free
50 pcs (Tape 50 pcs cut)
Standard products
PS2933-1-F3AX
PS2933-1-V-AX
(Ni/Pd/Au)
Embossed Tape 3 500
pcs/reel
50 pcs (Tape 50 pcs cut)
(UL, BSI approved)
Embossed Tape 3 500
pcs/reel
(VDE 0884-5)
Approved (Option)
PS2933-1-V-F3 PS2933-1-V-F3AX
Note:
Packing Style
Safety Standard
Approval
Application
Part
*1
Number
PS2933-1
UL, BSI,
DIN EN 60747-5-5
*1. For the application of the Safety Standard, following part number should be used.
ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified)
Diode
Parameter
Forward Current
Forward Current Derating
*1
Detector
Peak Forward Current
Power Dissipation
Reverse Voltage
Collector to Emitter Voltage
Emitter to Collector Voltage
Collector Current
Power Dissipation Derating
Power Dissipation
Isolation Voltage *2
Total Power Dissipation
Operating Ambient Temperature
Storage Temperature
Symbol
IF
ΔIF/°C
IFP
Ratings
50
0.5
0.5
Unit
mA
mA/°C
A
PD
VR
VCEO
VECO
IC
ΔPC/°C
PC
60
6
350
0.3
60
1.2
120
mW
V
V
V
mA
mW/°C
mW
BV
2 500
Vr.m.s.
PT
TA
Tstg
160
−55 to +100
−55 to +150
mW
°C
°C
Notes: *1. PW = 100 μs, Duty Cycle = 1%
*2. AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output.
Pins 1-2 shorted together, 3-4 shorted together.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 3 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
ELECTRICAL CHARACTERISTICS (TA = 25°C)
Parameter
Forward Voltage
Reverse Current
Terminal Capacitance
Diode
Transistor
Collector to Emitter
Current
Coupled
Current Transfer Ratio
(IC/IF)
CTR
IF = 1 mA, VCE = 2 V
Collector Saturation
Voltage
Isolation Resistance
Isolation Capacitance
VCE(SAT)
IF = 1 mA, IC = 2 mA
Rise Time
Fall Time
Note:
Symbol
Conditions
VF
IF = 1 mA
IR
VR = 5 V
Ct
V = 0 V, f = 1 MHz
VCE = 350V
ICEO
*1
RI-O
CI-O
tr
*1
MIN.
0.9
TYP.
1.1
MAX.
1.3
5
400
Unit
V
μA
pF
nA
2 000
4 500
%
0.8
1
V
15
400
1011
VI-O = 1 kVDC
V = 0 V, f = 1 MHz
VCC = 5 V, IC = 10 mA, RL = 100 Ω
0.4
Ω
pF
20
μs
5
tf
*1. Test circuit for switching time
Pulse Input
VCC
Input
ton
td
PW = 1 ms
Duty cycle = 1/10
toff
ts
90%
IF
VOUT
Output
10%
tr
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
tf
Page 4 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
TYPICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified)
MAXIMUM FORWARD CURRENT vs.
AMBIENT TEMPERATURE
Transistor Power Dissipation PC (mW)
Maximum Forward Current IF (mA)
80
60
40
0.5 mA/°C
20
50
25
0
TRANSISTOR POWER DISSIPATION
vs. AMBIENT TEMPERATURE
100
75
125
140
120
100
80
60
1.2 mW/°C
40
20
0
25
50
75
100
125
Ambient Temperature TA (°C)
Ambient Temperature TA (°C)
FORWARD CURRENT vs.
FORWARD VOLTAGE
COLLECTOR CURRENT vs.
COLLECTOR TO EMITTER VOLTAGE
100
60
10
Collector Current IC (mA)
Forward Current IF (mA)
IF = 5 mA
TA = +100°C
+60°C
+25°C
1
0°C
–25°C
–50°C
0.1
50
2 mA
40
1 mA
30
20
10
0.5 mA
0.01
0.0
0.5
1.0
1.5
0
2.0
Forward Voltage VF (V)
2
3
4
5
Collector to Emitter Voltage VCE (V)
COLLECTOR TO EMITTER DARK
CURRENT vs. AMBIENT TEMPERATURE
COLLECTOR CURRENT vs.
COLLECTOR SATURATION VOLTAGE
100
100 000
VCEO = 300 V
10 000
Collector Current IC (mA)
Collector to Emitter Dark Current ICEO (nA)
1
CTR = 1 068%
2 290%
4 360%
1 000
100
10
10
IF = 5 mA
2 mA
1 mA
0.5 mA
1
–50
–25
0
25
50
75
100
Ambient Temperature TA (°C)
1
0.7
0.8
0.9
1.0
Collector Saturation Voltage VCE(sat) (V)
Remark The graphs indicate nominal characteristics.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 5 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
CURRENT TRANSFER RATIO vs.
FORWARD CURRENT
1.4
4 000
Current Transfer Ratio CTR (%)
Normalized Current Transfer Ratio CTR
NORMALIZED CURRENT TRANSFER
RATIO vs. AMBIENT TEMPERATURE
1.2
1.0
0.8
0.6
0.4
Normalized to 1.0
at TA = 25°C,
IF = 1 mA, VCE = 2 V
0.2
0.0
–50
–25
0
25
50
75
100
VCE = 2 V
3 500
Sample A
B
C
3 000
2 500
2 000
1 500
1 000
500
0
0.1
1
10
100
Forward Current IF (mA)
Ambient Temperature TA (°C)
SWITCHING TIME vs.
LOAD RESISTANCE
Switching Time t (μs)
1 000
100
VCC = 5 V,
IC = 10 mA,
CTR = 2 840%
tr
tf
ts
td
10
1
0.1
100
1 000
Load Resistance RL (Ω)
Remark The graphs indicate nominal characteristics.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 6 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
TAPING SPECIFICATIONS (UNIT: mm)
1.75±0.1
Outline and Dimensions (Tape)
5.5±0.05
2.9 MAX.
12.0±0.2
1.5+0.1
–0
4.0±0.1
5.3±0.1
2.0±0.05
0.3
1.55±0.05
2.4±0.1
2.9±0.1
4.0±0.1
Tape Direction
PS2933-1-F3
R
R
R
R
Outline and Dimensions (Reel)
2.0±0.5
330±2.0
2.0±0.5
13.0±0.2
100±1.0
21.0±0.8
13.5±1.0
Packing: 3 500 pcs/reel
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 7 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm)
5.7
4.7
4.14
0.6
(0.35)
1.27
0.8
( ) : Reference value
24-R0.1
Remark
This drawing is considered to meet air and outer creepage distance 4.0 mm minimum. All dimensions in
this figure must be evaluated before use.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 8 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
NOTES ON HANDLING
1. Recommended soldering conditions
(1) Infrared reflow soldering
• Peak reflow temperature
• Time of peak reflow temperature
• Time of temperature higher than 220°C
• Time to preheat temperature from 120 to 180°C
• Number of reflows
• Flux
260°C or below (package surface temperature)
10 seconds or less
60 seconds or less
120±30 s
Three or less
Rosin flux containing small amount of chlorine (The flux
with a maximum chlorine content of 0.2 Wt% or less is
recommended.)
Recommended Temperature Profile of Infrared Reflow
Package Surface Temperature T (˚C)
(heating)
to 10 s
260˚C MAX.
220˚C
to 60 s
180˚C
120˚C
120±30 s
(preheating)
Time (s)
(2) Wave soldering
• Temperature
• Time
• Preheating conditions
• Number of times
• Flux
260°C or below (molten solder temperature)
10 seconds or less
120°C or below (package surface temperature)
One (Allowed to be dipped in solder including plastic mold portion.)
Rosin flux containing small amount of chlorine (The flux with a maximum
chlorine content of 0.2 Wt% or less is recommended.)
(3) Soldering by Soldering Iron
• Peak Temperature (lead part temperature) 350°C or below
• Time (each pin)
3 seconds or less
• Flux
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% or less is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead
(4) Cautions
• Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 9 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
2. Cautions Regarding Noise
Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collectoremitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum
ratings.
3. Measurement conditions of current transfer ratios (CTR), which differ according to photocoupler
Check the setting values before use, since the forward current conditions at CTR measurement differ according to
product.
When using products other than at the specified forward current, the characteristics curves may differ from the
standard curves due to CTR value variations or the like. Therefore, check the characteristics under the actual
operating conditions and thoroughly take variations or the like into consideration before use.
USAGE CAUTIONS
1. Protect against static electricity when handling.
2. Avoid storage at a high temperature and high humidity.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 10 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
Parameter
Symbol
Climatic test class (IEC 60068-1/DIN EN 60068-1)
Dielectric strength
maximum operating isolation voltage
Test voltage (partial discharge test, procedure a for type test and
random test)
Upr = 1.6 × UIORM, Pd < 5 pC
Test voltage (partial discharge test, procedure b for all devices)
Upr = 1.875 × UIORM, Pd < 5 pC
Highest permissible overvoltage
Degree of pollution (DIN EN 60664-1 VDE0110 Part 1)
Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303
Part 11))
Material group (DIN EN 60664-1 VDE0110 Part 1)
Storage temperature range
Operating temperature range
Isolation resistance, minimum value
VIO = 500 V dc at TA = 25°C
VIO = 500 V dc at TA MAX. at least 100°C
Safety maximum ratings (maximum permissible in case of fault, see
thermal derating curve)
Package temperature
Current (input current IF, Psi = 0)
Power (output or total power dissipation)
Isolation resistance
VIO = 500 V dc at TA = Tsi
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Spec.
Unit
55/100/21
UIORM
Upr
570
912
Vpeak
Vpeak
Upr
1 068
Vpeak
UTR
4 000
2
Vpeak
CTI
175
Tstg
TA
III a
–55 to +150
–55 to +100
°C
Ris MIN.
Ris MIN.
1012
11
10
Ω
Ω
Tsi
Isi
Psi
150
300
500
°C
mA
mW
Ris MIN.
109
Ω
°C
Page 11 of 12
A Business Partner of Renesas Electronics Corporation.
PS2933-1e
Caution
GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe
the following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
R08DS0115EJ0100 Rev.1.00
Nov 29, 2013
Page 12 of 12
Revision History
PS2933-1 Data Sheet
Rev.
Date
Page
2.00
1.00
May , 2006
Nov 29, 2013
−
Throughout
p.1
p.2
p.3
p.4
p.6
p.7
p.9
p.11
Description
Summary
NEC Electronics format 2nd Edition
Renesas format is applied to this data sheet.
Modification of FEATURES
Modification of PACKAGE DIMENSIONS
Modification of MARKING EXAMPLE
Modification of ORDERING INFORMATION
Modification of ELECTRICAL CHARACTERISTICS
Modification of TYPICAL CHARACTERISTICS
Modification of TAPING SPECIFICATIONS
Modification of NOTES ON HANDLING
Addition of SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
All trademarks and registered trademarks are the property of their respective owners.
C-1
NOTICE
1.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and
application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California
Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits,
software, or information.
2.
California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does
not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
3.
California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property
rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express,
implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas
Electronics or others.
4.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern
Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy
or otherwise misappropriation of Renesas Electronics product.
5.
Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The recommended applications
for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; office equipment; communications
equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and
industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime
systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct
threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear
reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas
Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product
for which the product is not intended by California Eastern Laboratories or Renesas Electronics.
6.
You should use the Renesas Electronics products described in this document within the range specified by California Eastern Laboratories, especially with
respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product
characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products
beyond such specified ranges.
7.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as
the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation
resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by
fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy,
fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of
microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you.
Please contact a California Eastern Laboratories sales office for details as to environmental matters such as the environmental compatibility of each Renesas
8.
Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for
damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9.
Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document
for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When
exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics
product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and
Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories.
12. Please contact a California Eastern Laboratories sales office if you have any questions regarding the information contained in this document or Renesas
Electronics products, or if you have any other inquiries.
NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
NOTE 3: Products and product information are subject to change without notice.
CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com
For a complete list of sales offices, representatives and distributors,
Please visit our website: www.cel.com/contactus