PS9117A-V-F3

PHOTOCOUPLER PS9117A HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 5-PIN SOP (SO-5) −NEPOC HIGH-SPEED PHOTOCOUPLER DESCRIPTION The PS9117A is an optically coupled high-speed, active low type isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9117A is designed specifically for high common mode transient immunity (CMR) and low pulse width distortion. The PS9117A is suitable for high density application. Series− FEATURES • Pulse width distortion ( tPHL − tPLH = 35 ns MAX.) • High common mode transient immunity (CMH, CML = ±15 kV/µs MIN.) • Small package (SO-5) • High-speed (10 Mbps) • High isolation voltage (BV = 3 750 Vr.m.s.) • Open collector output • Ordering number of taping product: PS9117A-F3: 2 500 pcs/reel • Pb-Free product 1 2 5 4 PIN CONNECTION (Top View) 3 1. Anode 2. Cathode 3. GND 4. VO 5. VCC APPLICATIONS • Measurement equipment • PDP • FA Network TRUTH TABLE LED ON OFF Output L H Document No. PN10646EJ01V0DS (1st edition) Date Published November 2006 NS CP(K) 2006 PS9117A PACKAGE DIMENSIONS (UNIT: mm) 3.4 5 +0.3 –0.1 4 3 7.0±0.3 1 2 4.4 2.6±0.2 0.15 +0.10 –0.05 0.1±0.1 1.27 0.4 +0.10 –0.05 0.25 M 0.5±0.3 MARKING EXAMPLE 117A N631 No. 1 pin Mark Initial of NEC (Engraved mark) N Assembly Lot *1 N 6 31 Week Assembled Year Assembled (Last 1 Digit) Rank Code *1 Bar : Pb-Free 2 Preliminary Data Sheet PN10646EJ01V0DS PS9117A ORDERING INFORMATION Part Number Order Number Solder Plating Specification PS9117A PS9117A-F3 PS9117A-V PS9117A-V-F3 PS9117A-A PS9117A-F3-A PS9117A-V-A PS9117A-V-F3-A Pb-Free 20 pcs (Tape 20 pcs cut) Embossed Tape 2 500 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 2 500 pcs/reel Packing Style Safety Standards Approval Standard products (UL approved) DIN EN60747-5-2 (VDE0884 Part2) approved (Option) Application Part Number PS9117A *1 *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) Parameter Diode Forward Current *1 Symbol IF VR VCC VO IO *2 Ratings 30 5 7 7 25 40 3 750 −40 to +85 −55 to +125 Unit mA V V V mA mW Vr.m.s. °C °C Reverse Voltage Detector Supply Voltage Output Voltage Output Current Power Dissipation PC BV TA Tstg Isolation Voltage *3 Operating Ambient Temperature Storage Temperature *1 Reduced to 0.3 mA/°C at TA = 25°C or more. *2 Applies to output pin VO (collector pin). Reduced to 1.5 mW/°C at TA = 65°C or more. *3 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output. Pins 1-2 shorted together, 3-5 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Low Level Input Voltage High Level Input Current Supply Voltage TTL (RL = 1 kΩ, loads) Pull-up Resistor Symbol VFL IFH VCC N RL 330 MIN. 0 6.3 4.5 10 5.0 TYP. MAX. 0.8 12.5 5.5 5 4k Ω Unit V mA V Preliminary Data Sheet PN10646EJ01V0DS 3 PS9117A ELECTRICAL CHARACTERISTICS (TA = −40 to +85°C, unless otherw ise specified) Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Current Low Level Output Voltage High Level Supply Current Low Level Supply Current Coupled Threshold Input Current (H → L) Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60%, TA = 25°C Isolation Capacitance Propagation Delay Time (H → L) *3 *2 Symbol VF IR Ct IOH VOL ICCH ICCL IFHL Conditions IF = 10 mA, TA = 25°C VR = 3 V, TA = 25°C V = 0 V, f = 1 MHz, TA = 25°C VCC = VO = 5.5 V, VF = 0.8 V VCC = 5.5 V, IF = 5 mA, IOL = 8 mA VCC = 5.5 V, IF = 0 mA, VO = open VCC = 5.5 V, IF = 10 mA, VO = open VCC = 5 V, VO = 0.8 V, RL = 350 Ω MIN. 1.4 TYP. *1 MAX. 1.8 10 Unit V 1.65 µA pF 30 1 0.2 4 6 2 100 0.6 7 10 5 µA V mA 10 11 Ω CI-O tPHL V = 0 V, f = 1 MHz, TA = 25°C TA = 25°C 0.6 40 75 100 pF ns Propagation Delay Time (L → H) *3 tPLH TA = 25°C 45 75 100 Rise Time Fall Time Pulse Width Distortion (PWD) *3 tr tf tPHL-tPLH VCC = 5 V, RL = 350 Ω, IF = 7.5 mA VTHHL = VTHLH = 1.5 V 20 5 5 35 Propagation Delay Skew Common Mode Transient Immunity at High Level Output *4 tPSK CMH VCC = 5 V, RL = 350 Ω, TA = 25°C, IF = 0 mA, VO > 2 V, VCM = 1 kV VCC = 5 V, RL = 350 Ω, TA = 25°C, IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV 15 20 40 kV/µs Common Mode Transient Immunity at Low Level Output *4 CML 15 20 kV/µs 4 Preliminary Data Sheet PN10646EJ01V0DS PS9117A *1 Typical values at TA = 25°C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time Input Pulse input (IF) (PW = 1 µ s, Duty cycle = 1/10) Input (monitor) 47 Ω 0.1 µ F RL = 350 Ω VO (monitor) CL = 15 pF VCC = 5 V (IF = 7.5 mA) 50% Output 1.5 V VOL tPHL tPLH Remark CL includes probe and stray wiring capacitance. *4 Test circuit for common mode transient immunity VCM 90% VCC = 5 V 0.1 µ F RL = 350 Ω 1 kV 0V tr tf SW IF 10% VO (monitor) CL = 15 pF VO (IF = 0 mA) VCM VOH 2V 0.8 V VOL VO (IF = 7.5 mA) Remark CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 µF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. Preliminary Data Sheet PN10646EJ01V0DS 5 PS9117A TAPING SPECIFICATIONS (UNIT: mm) Outline and Dimensions (Tape) 2.0±0.05 4.0±0.1 1.75±0.1 7.4±0.1 1.5+0.1 –0 3.45 MAX. 1.55±0.1 8.0±0.1 12.0±0.2 5.5±0.1 3.9±0.1 3.0±0.1 0.3±0.05 Tape Direction PS9117A-F3 Outline and Dimensions (Reel) 2.0±0.5 2.0±0.5 13.0±0.2 R 1.0 21.0±0.8 φ 13.0±0.2 φ 330±2.0 φ 100±1.0 13.5±1.0 17.5±1.0 Packing: 2 500 pcs/reel 11.9 to 15.4 Outer edge of flange 6 Preliminary Data Sheet PN10646EJ01V0DS PS9117A NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature • Time of peak reflow temperature • Time of temperature higher than 220°C • Time to preheat temperature from 120 to 180°C • Number of reflows • Flux 260°C or below (package surface temperature) 10 seconds or less 60 seconds or less 120±30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (˚C) (heating) to 10 s 260˚C MAX. 220˚C to 60 s 180˚C 120˚C 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature • Time • Preheating conditions • Number of times • Flux 260°C or below (molten solder temperature) 10 seconds or less 120°C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron • Peak Temperature (lead part temperature) • Time (each pins) • Flux 350°C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100°C Preliminary Data Sheet PN10646EJ01V0DS 7 PS9117A (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. 8 Preliminary Data Sheet PN10646EJ01V0DS PS9117A • T he information in this document is current a s of November, 2 006. T he information is subject to change without notice. For actual design-in, refer to the latest p ublications of NEC Electronics data s heets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not a ll products and/or types are available in every country. Please check with an NEC Electronics sales r epresentative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior w ritten c onsent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may a ppear in this document. • NEC E lectronics does not assume any liability for infringement of patents, copyrights or other intellectual property r ights of third parties by or arising from the use of NEC Electronics products listed in this document o r any other liability arising f rom the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other i ntellectual property rights of N EC E lectronics or o thers. • Descriptions of circuits, software and other related information in this document are provided for illustrative p urposes in semiconductor product operation and application examples. The incorporation of these c ircuits, software and information in the design of a customer's equipment shall be done under the full r esponsibility of the customer. N EC E lectronics a ssumes no responsibility for any losses incurred by c ustomers or third parties arising from t he use of these circuits, software and information. • While NEC E lectronics endeavors to enhance the quality, reliability and safety of NEC E lectronics products, customers agree and acknowledge that th e p ossibility of defects thereof cannot be eliminated entirely. To m inimize risks of damage to property or injury (including d eath) to persons a rising from defects in NEC E lectronics products, c ustomers must incorporate s ufficient safety m easures in their design, such as r edundancy, fire-containment and anti-failure features. • NEC Electronics p roducts are classified into the following t hree quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC E lectronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC E lectronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC E lectronics product b efore using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically d esigned for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC E lectronics products is "Standard" unless otherwise expressly specified in NEC E lectronics data sheets or data books, etc. I f c ustomers wish to use NEC Electronics products in applications n ot intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to d etermine NEC Electronics' willingness to support a given application. (Note) (1) "NEC E lectronics" as used in this statement means NEC E lectronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or m anufactured by or for N EC Electronics ( as defined above). M8E 02. 11-1 Preliminary Data Sheet PN10646EJ01V0DS 9 PS9117A Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.