PHOTOCOUPLER
PS9552,PS9552L1,PS9552L2,PS9552L3
2.5 A OUTPUT CURRENT, HIGH CMR
IGBT GATE DRIVE PHOTOCOUPLER
8-PIN DIP PHOTOCOUPLER
NEPOC Series
DESCRIPTION
The PS9552, PS9552L1, PS9552L2 and PS9552L3 are optically coupled isolators containing a GaAlAs LED on
the input side and a photo diode, a signal processing circuit and a power output transistor on the output side on one
chip.
The PS9552 Series is designed specifically for high common mode transient immunity (CMR), high output current
and high switching speed.
The PS9552 Series is suitable for driving IGBTs and MOS FETs.
The PS9552 Series is in a plastic DIP (Dual In-line Package).
The PS9552L1 is lead bending type for long creepage distance.
The PS9552L2 is lead bending type for long creepage distance (Gull-wing) for surface mount.
The PS9552L3 is lead bending type (Gull-wing) for surface mounting.
FEATURES
• Long creepage distance (8 mm MIN.: PS9552L1, PS9552L2)
• Large peak output current (2.5 A MAX., 2.0 A MIN.)
• High speed switching (tPLH tPHL = 0.5 s MAX.)
• UVLO (Under Voltage Lock Out) protection with hysteresis
• High common mode transient immunity (CM H, CML = 25 kV/ s MIN.)
• Ordering number of tape product: PS9552L2-E3: 1 000 pcs/reel
: PS9552L3-E3: 1 000 pcs/reel
• Pb-Free product
• Safety standards
• UL approved: No. E72422
• CSA approved: No. CA 101391 (CA5A, CAN/CSA-C22.2 60065, 60950)
• BSI approved: No. 8937, 8938
• SEMKO approved: No. 615433
• NEMKO approved: No. P06207243
• DEMKO approved: No. 314091
• FIMKO approved: No. FI 22827
• DIN EN60747-5-2 (VDE0884 Part2) approved: No. 40019182 (Option)
APPLICATIONS
• IGBT, Power MOS FET Gate Driver
• Industrial inverter
• IH (Induction Heating)
Document No. PN10589EJ07V0DS (7th edition)
Date Published September 2009 NS
The mark shows major revised points.
The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field.
PS9552,PS9552L1,PS9552L2,PS9552L3
PACKAGE DIMENSIONS (UNIT: mm)
DIP Type
Lead Bending Type (Gull-wing) For Surface Mount
2
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
Lead Bending Type For Long Creepage Distance
Lead Bending Type (Gull-wing) For Long Creepage Distance (Surface Mount)
Data Sheet PN10589EJ07V0DS
3
PS9552,PS9552L1,PS9552L2,PS9552L3
PHOTOCOUPLER CONSTRUCTION
Parameter
PS9552, PS9552L3
PS9552L1, PS9552L2
Air Distance (MIN.)
7 mm
8 mm
Outer Creepage Distance (MIN.)
7 mm
8 mm
0.4 mm
0.4 mm
Isolation Distance (MIN.)
FUNCTIONAL DIAGRAM
MARKING EXAMPLE
4
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
ORDERING INFORMATION
Part Number
Order Number
Solder Plating
Specification
Packing Style
Safety Standard
Approval
Application Part
Number*1
Magazine case 50 pcs
Standard products
PS9552
(UL, CSA, BSI,
PS9552L1
PS9552
PS9552-AX
Pb-Free
PS9552L1
PS9552L1-AX
(Ni/Pd/Au)
PS9552L2
PS9552L2-AX
SEMKO, NEMKO,
PS9552L2
PS9552L3
PS9552L3-AX
DEMKO, FIMKO
PS9552L3
PS9552L2-E3
PS9552L2-E3-AX
approved)
PS9552L2
PS9552L3-E3
PS9552L3-E3-AX
PS9552-V
PS9552-V-AX
PS9552L1-V
PS9552L2-V
PS9552L3-V
PS9552L3-V-AX
PS9552L2-V-E3
PS9552L2-V-E3-AX
PS9552L3-V-E3
PS9552L3-V-E3-AX
Embossed Tape 1 000 pcs/reel
PS9552L3
Magazine case 50 pcs
DIN EN60747-5-2
PS9552
PS9552L1-V-AX
(VDE0884 Part2)
PS9552L1
PS9552L2-V-AX
Approved (Option)
PS9552L2
PS9552L3
Embossed Tape 1 000 pcs/reel
PS9552L2
PS9552L3
*1 For the application of the Safety Standard, following part number should be used.
Data Sheet PN10589EJ07V0DS
5
PS9552,PS9552L1,PS9552L2,PS9552L3
ABSOLUTE MAXIMUM RATINGS (T A = 25 C, unless otherwise specified)
Parameter
Diode
Symbol
Forward Current
Ratings
Unit
IF
25
mA
IF (TRAN)
1.0
A
VR
5
V
High Level Peak Output
Current *1
IOH (PEAK)
2.5
A
Low Level Peak Output
Current *1
IOL (PEAK)
2.5
A
(VCC - VEE)
0 to 35
V
VO
0 to VCC
V
PC
250
mW
BV
5 000
Vr.m.s.
PT
300
mW
f
50
kHz
Operating Ambient Temperature
TA
40 to +100
C
Storage Temperature
Tstg
55 to +125
C
Peak Transient Forward
Current (Pulse Width < 1 s)
Reverse Voltage
Detecto
r
Supply Voltage
Output Voltage
Power Dissipation
Isolation Voltage
*2
*3
Total Power Dissipation
Operating Frequency
*4
*5
*1 Maximum pulse width = 10 s, Maximum duty cycle = 0.2%
*2 Reduced to 4.8 mW/ C at TA = 70 C or more.
*3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output.
Pins 1-4 shorted together, 5-8 shorted together.
*4 Reduced to 5.4 mW/ C at TA = 70 C or more.
*5 IOH (PEAK)
2.0 A ( 0.3 s), IOL (PEAK)
2.0 A ( 0.3 s)
RECOMMENDED OPERATING CONDITIONS
Parameter
Supply Voltage
Forward Current (ON)
Forward Voltage (OFF)
Operating Ambient Temperature
6
Symbol
MIN.
(VCC - VEE)
15
IF (ON)
7
VF (OFF)
TA
TYP.
MAX.
Unit
30
V
16
mA
2
0.8
V
40
100
C
10
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
ELECTRICAL CHARACTERISTICS (T A = 40 to +100 C, VCC = 15 to 30 V, IF (ON) = 7 to 16 mA,
VF (OFF) = 2 to 0.8 V, VEE = GND, unless otherwise specified)
Parameter
Diode
Symbol
Conditions
Forward Voltage
VF
IF = 10 mA, TA = 25 C
Input Capacitance
CIN
f = 1 MHz, VF = 0 V, TA = 25 C
Detector High Level Output Current
IOH
VO = (VCC 4 V)
*2
VO = (VCC 15 V)
Low Level Output Current
IOL
*3
VO = (VEE + 2.5 V) *2
VO = (VEE + 15 V)
*3
*4
TYP.*1
MAX.
Unit
1.3
1.65
2.1
V
30
pF
2.0
A
2.0
A
VCC 3.5 VCC 2.5 VCC 1.5
V
0.5
2.0
0.5
2.0
High Level Output Voltage
VOH
IO = 100 mA
Low Level Output Voltage
VOL
IO = 100 mA
0.1
0.5
V
High Level Supply Current
ICCH
VO = open, IF = 7 to 16 mA
2.0
5.0
mA
Low Level Supply Current
ICCL
VO = open, VF = 2 to +0.8 V
2.0
5.0
mA
11.0
12.3
13.5
V
9.5
10.7
12.0
UVLO Threshold
VUVLO+
VO > 5 V, IF = 10 mA
VUVLO
UVLO Hysteresis
Coupled
MIN.
Threshold Input Current
(L
UVLOHYS VO > 5 V, IF = 10 mA
IFLH
IO = 0 mA, VO > 5 V
VFHL
IO = 0 mA, VO < 5 V
1.6
2.0
V
5.0
mA
H)
Threshold Input Voltage
(H
L)
0.8
V
*1 Typical values at TA = 25 C.
*2 Maximum pulse width = 50 s, Maximum duty cycle = 0.5%.
*3 Maximum pulse width = 10 s, Maximum duty cycle = 0.2%
*4 VOH is measured with the DC load current in this testing (Maximum pulse width = 2 ms, Maximum duty cycle =
20%).
Data Sheet PN10589EJ07V0DS
7
PS9552,PS9552L1,PS9552L2,PS9552L3
SWITCHING CHARACTERISTICS (T A = 40 to +100 C, VCC = 15 to 30 V, IF (ON) = 7 to 16 mA,
VF (OFF) = 2 to 0.8 V, VEE = GND, unless otherwise specified)
Parameter
Propagation Delay Time (L
Propagation Delay Time (H
Symbol
H)
L)
tPLH
tPHL
Pulse Width Distortion (PWD)
|tPHL tPLH|
Propagation Delay Time (Difference
Between Any Two Products)
tPHL tPLH
Conditions
Rg = 10
, Cg = 10 nF, f = 10 kHz,
*2
Duty Cycle = 50% , IF = 7 to 16 mA
MIN.
TYP.*1
MAX.
Unit
0.1
0.3
0.5
s
0.1
0.3
0.5
s
0.3
s
0.35
s
0.35
Rise Time
tr
0.1
s
Fall Time
tf
0.1
s
UVLO (Turn On Delay)
tUVLO ON
VO > 5 V, IF = 10 mA
0.8
s
UVLO (Turn Off Delay)
tUVLO OFF
VO < 5 V, IF = 10 mA
0.6
s
Common Mode Transient Immunity at
High Level Output*3
|CM H|
TA = 25 C, IF = 10 to 16 mA, VCC = 30 V,
VO (MIN.) = 26 V, VCM = 1.5k V
25
kV// s
Common Mode Transient Immunity at
Low Level Output*3
|CM L|
TA = 25 C, IF = 0 mA, VCC = 30 V,
VO (MAX.) = 1 V, VCM = 1.5k V
25
kV// s
*1 Typical values at TA = 25 C.
*2 This load condition is equivalent to the IGBT load at 1 200 V/75 A.
*3 Connect pin 1 and pin 4 to the LED common.
8
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
TEST CIRCUIT
Data Sheet PN10589EJ07V0DS
9
PS9552,PS9552L1,PS9552L2,PS9552L3
Remark CMR Test : Connect pin 1 and pin 4 to the LED common.
10
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
TYPICAL CHARACTERISTICS (T A = 25 C, unless otherwise specified)
Remark The graphs indicate nominal characteristics.
Data Sheet PN10589EJ07V0DS
11
PS9552,PS9552L1,PS9552L2,PS9552L3
Remark The graphs indicate nominal characteristics.
12
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
Remark The graphs indicate nominal characteristics.
Data Sheet PN10589EJ07V0DS
13
PS9552,PS9552L1,PS9552L2,PS9552L3
Remark The graphs indicate nominal characteristics.
14
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
TAPING SPECIFICATIONS (UNIT: mm)
Data Sheet PN10589EJ07V0DS
15
PS9552,PS9552L1,PS9552L2,PS9552L3
16
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm)
Data Sheet PN10589EJ07V0DS
17
PS9552,PS9552L1,PS9552L2,PS9552L3
NOTES ON HANDLING
1. Recommended soldering conditions
(1) Infrared reflow soldering
• Peak reflow temperature
260 C or below (package surface temperature)
• Time of peak reflow temperature
10 seconds or less
• Time of temperature higher than 220 C
60 seconds or less
• Time to preheat temperature from 120 to 180 C
120 30 s
• Number of reflows
Three
• Flux
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
(2) Wave soldering
• Temperature
260 C or below (molten solder temperature)
• Time
10 seconds or less
• Preheating conditions
120 C or below (package surface temperature)
• Number of times
One (Allowed to be dipped in solder including plastic mold portion.)
• Flux
Rosin flux containing small amount of chlorine (The flux with a maximum chlorine
content of 0.2 Wt% is recommended.)
(3) Soldering by Soldering Iron
• Peak Temperature (lead part temperature)
350 C or below
• Time (each pins)
3 seconds or less
• Flux
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead
(b) Please be sure that the temperature of the package would not be heated over 100 C
18
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
(4) Cautions
• Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler’s input and output at startup, the
output transistor may enter the on state, even if the voltage is within the absolute maximum ratings.
USAGE CAUTIONS
1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static
electricity when handling.
2. Board designing
(1) By-pass capacitor of more than 0.1 F is used between V CC and GND near device. Also, ensure that the
distance between the leads of the photocoupler and capacitor is no more than 10 mm.
(2) In older to avoid malfunctions and characteristics degradation, IGBT collector or emitter traces should not
be closed to the LED input.
(3) Pins 1, 4 (which is an NC
*1
pin) can either be connected directly to the GND pin on the LED side or left
open.
Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this
may degrade the internal noise environment of the device.
*1 NC: Non-Connection (No Connection)
3. Make sure the rise/fall time of the forward current is 0.5 s or less.
4. In order to avoid malfunctions, make sure the rise/fall slope of the supply voltage is 3 V/ s or less.
5. Avoid storage at a high temperature and high humidity.
Data Sheet PN10589EJ07V0DS
19
PS9552,PS9552L1,PS9552L2,PS9552L3
SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
Parameter
Symbol
Climatic test class (IEC 60068-1/DIN EN 60068-1)
Spec.
Unit
55/100/21
Dielectric strength
maximum operating isolation voltage
Test voltage (partial discharge test, procedure a for type test and random test)
Upr = 1.5 UIORM, Pd 5 pC
UIORM
Upr
1 130
1 695
Vpeak
Vpeak
Test voltage (partial discharge test, procedure b for all devices)
Upr = 1.875 UIORM, Pd 5 pC
Upr
2 119
Vpeak
Highest permissible overvoltage
UTR
8 000
Vpeak
Degree of pollution (DIN EN 60664-1 VDE0110 Part 1)
Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11))
2
CTI
Material group (DIN EN 60664-1 VDE0110 Part 1)
175
III a
Storage temperature range
Tstg
–55 to +125
°C
Operating temperature range
TA
–40 to +100
°C
Ris MIN.
Ris MIN.
1012
1011
Tsi
Isi
175
400
°C
mA
Psi
700
mW
Ris MIN.
109
Isolation resistance, minimum value
VIO = 500 V dc at TA = 25°C
VIO = 500 V dc at TA MAX. at least 100°C
Safety maximum ratings (maximum permissible in case of fault, see thermal
derating curve)
Package temperature
Current (input current IF, Psi = 0)
Power (output or total power dissipation)
Isolation resistance
VIO = 500 V dc at TA = Tsi
20
Data Sheet PN10589EJ07V0DS
PS9552,PS9552L1,PS9552L2,PS9552L3
Data Sheet PN10589EJ07V0DS
21
PS9552,PS9552L1,PS9552L2,PS9552L3
Caution
GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the
following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.