CHDTC124XEPT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT NPN Digital Silicon Transistor VOLTAGE 50 Volts APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. C HDTC124XEPT CURRENT 100 mAmpere FEATURE * Small surface mounting type. (SC-75/SOT-416) * High current gain. * Suitable for high packing density. * * * * Low colloector-emitter saturation. High saturation current capability. Internal isolated NPN transistors in one package. Built in bias resistor(R1=22kΩ, Typ. ) 0.1 0.2±0.05 0.5 1.6±0.2 0.5 SC-75/SOT-416 (2) (3) 1.0±0.1 0.1 0.3±0.05 (1) CONSTRUCTION * One NPN transistors and bias of thin-film resistors in one package. 0.1 0.2±0.05 0.8±0.1 MARKING XEB Gnd In 1 0.15±0.05 0.1Min. 0.6~0.9 0~0.1 1.6±0.2 CIRCUIT 2 R2 TR R1 3 Out Dimensions in millimeters SC-75/SOT-416 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL VCC VIN IO DC Output current IC(Max.) PTOT TSTG TJ RθJ-S Note 1. Transistor mounted on an FR4 printed-circuit board. 2003-12 PARAMETER Supply voltage Input voltage CONDITIONS − MIN. MAX. 50 +40 100 V V UNIT -10 − − Tamb ≤ 25 OC, Note 1 − −55 − junction - soldering point − mA 100 150 +150 150 150 mW O Total power dissipation Storage temperature Junction temperature Thermal resistance C C C/W O O RATING CHARACTERISTIC ( CHDTC124XEPT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL VIoff) VI(on) VO(on) II IO(off) hFE R1 R2/R1 fT PARAMETER Input off voltage Input on voltage Output voltage Input current Output current DC current gain Input resistor Resistor ratio Transition frequency IE=-5mA, VCE=10.0V f=100MHz = CONDITIONS IO=100uA; VCC=5.0V IO=2mA; VO=0.3V IO=10mA; II=0.5mA VI=5V VI=0V; VCC=50V IO=5mA; VO=5.0V − − − − 68 15.4 1.7 − MIN. 0.5 − − 0.1 − − − 22 2.1 250 TYP. − 2.5 0.3 0.36 0.5 − 28.6 2.6 − KΩ MHz MAX. V V V mA uA UNIT Note 1.Pulse test: tp≤300uS; δ≤0.02. RATING CHARACTERISTIC CURVES ( CHDTC124XEPT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) 100 50 VO= 0.3V Fig.2 Output current vs. input voltage (OFF characteristics) 10m 5m OUTPUT CURRENT : Io (A) VCC= 5V INPUT VOLTAGE : VI(on) (V) 2m 1m 20 10 5 2 1 500m 200m 100m 100 200 500 1m 2m 5m 10m 20m 50m 100m Ta =- 40OC 25OC = 100OC 100u Ta=100OC 25OC -40 OC 10u 1u 0 1.0 2.0 3.0 OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI(off) (V) 1k 500 DC CURRENT GAIN : GI Fig.3 DC current gain vs. output current OUTPUT VOLTAGE : VO(on) (V) Fig.4 Output voltage vs. output current 1 500m 200m 100m 50m 20m 10m 5m 2m Ta=100OC 25OC -40 OC 200 100 50 20 10 5 2 1 100u Ta=100OC 25OC -40OC VO = 5V lO/lI=20 1m 10m 100m 1m 100u 1m 10m 100m OUTPUT CURRENT : IO (A) OUTPUT CURRENT : IO (A)