VRE107MA

P r o d u c t IIn n o vva t i o n FF r o m rom nno a VRE107 VRE107 DESCRIPTION Precision Voltage Reference FEaTuRES ♦ Very High Accuracy: ±5 V, ±0.4 mV ♦ Extremely Low Drift: 0.6 ppm/°C (-55°C to +125°C) ♦ Excellent Stability: 6 ppm/1000 Hrs. Typical ♦ Excellent Line Regulation: 6 ppm/V Typical ♦ Wide Supply Range: ±13.5 V to ±22 V ♦ Hermetic 14-pin Ceramic DIP ♦ Military Processing Option VRE107 Series Precision Voltage References provide ultrastable ±5 V outputs with ±0.4 mV initial accuracy and temperature coefficient as low as 0.6 ppm/°C over the full military temperature range. This impovement in accuracy is made possible by a unique, proprietary multipoint laser compensation technique. Significant improvements have been made in other performance parameters as well, including initial accuracy, warm-up drift, line regulation, and long-term stability, making the VRE107 series the most accurate and stable 5 V references available. VRE107 series devices are available in two operating temperature ranges, -25°C to +85°C and -55°C to +125°C, and two performance grades. All devices are packaged in 14-pin hermetic ceramic packages for maximum long-term stablity. “M” versions are screened for high reliability and quality. Superior stability, accuracy, and quality make these references ideal for precision applications such as A/D and D/A converters, high accuracy test and measurement instrumentation, and tranducer excitation. aPPlICaTIONS ♦ ♦ ♦ ♦ ♦ ♦ Precision A/D and D/A Converters Transducer Excitation Accurate Comparator Threshold Reference High Resolution Servo Systems Digital Voltmeters High Precision Test and Measurement Instruments Figure 1. BlOCk DIagRam VRE107DS http://www.cirrus.com Copyright © Cirrus Logic, Inc. 2009 (All Rights Reserved) maR 2009 1 APEX − VRE107DSREVD VRE107 SElECTION guIDE model VRE107M VRE107MA Output (V) ±5 ±5 Temperature Operating Range -55°C to +125°C -55°C to +125°C P r o d u c t I n n o v a t i o nF r o m Volt Deviation (maX) ±0.6mV ±0.3mV 1. ChaRaCTERISTICS aND SPECIFICaTIONS ElECTRICal SPECIFICaTIONS VPS =±15V, T = +25°C, RL = 10K Ω UnLESS OTHERWISE nOTED. model Parameter Power Supply Operating Temperature Storage Temperature Short Circuit Protection OuTPuT VOlTagE VRE107 OuTPuT VOlTagE ERRORS Initial Error Warmup Drift TMIn - TMAX (note1) 6 3 ±10 6 3 10 4 7 4 9 6 10 * Long-Term Stability noise (0.1 - 10Hz) OuTPuT CuRRENT Range REgulaTION Line Load OuTPuT aDJuSTmENT Range Temperature Coefficient POWER SuPPlY CuRRENT (note 2) VRE107 +PS VRE107 -PS 2 600 ±800 ±5 min ±13.5 -55 -65 Continuous aBSOluTE maXImum RaTINgS ±22 +125 +150 * * * VRE107m Typ max min hermetic 14-pin Ceramic DIP Package Style hC VRE107ma Typ max * * * * * ±400 1 300 * * V µV ppm µV ppm/1000hrs. µVpp mA * * * * * * * * * ppm/V ppm/mA mV µV/ºC/mV mA mA units V ºC ºC nOTES: * Same as M Models. 1. Using the box method, the specified value is the maximum deviation from the output voltage at 25°C over the specified operating temperature range. 2. The specified values are unloaded. 2 VRE107DS P r o d u c t I n n o v a t i o nF r o m VRE107 TYPICal PERFORmaNCE gRaPhS VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE Temperature oC VRE107M POSITIVE OUTPUT QUIESCENT CURRENT VS. TEMP Temperature oC VRE107MA JUNCTION TEMP. RISE VS. OUTPUT CURRENT PSRR VS. FREQUENCY Temperature oC Output Current (mA) NEGATIVE OUTPUT JUNCTION TEMP. RISE VS. OUTPUT CURRENT Frequency (Hz) QUIESCENT CURRENT VS. TEMP PSRR VS. FREQUENCY Temperature oC Output Current (mA) Frequency (Hz) 2. ThEORY OF OPERaTION The following discussion refers to the block diagram in Figure 1. A FET current source is used to bias a 6.3 V zener diode. The zener voltage is divided by the resistor network R1 and R2. This voltage is then applied to the noninverting input of the operational amplifier which amplifies the voltage to produce a 5 V output. The gain is determined by the resistor networks R3 and R4: G=1 + R4/R3. The 6.3 V zener diode is used because it is the most stable diode over time and temperature. The current source provides a closely regulated zener current, which determines the slope of the reference’s voltage vs. temperature function. By trimming the zener current, a lower drift over temperature can be achieved. But since the voltage vs. temperature function is nonlinear, this method leaves a residual error over wide temperature ranges. VRE107DS  VRE107 P r o d u c t I n n o v a t i o nF r o m To remove this residual error, a nonlinear compensation network of thermistors and resistors is used in the VRE107 series references. This proprietary network eliminates most of the nonlinearity in the voltage vs. temperature function. By then adjusting the slope, The VRE107 series produces a very stable voltage over wide temperature ranges. This network is less than 2% of the overall network resistance so it has a negligible effect on long term stability. . aPPlICaTION INFORmaTION The proper connection of the VRE107 series voltage reference is shown below with the optional trim resistors. When trimming the VRE107, the positive voltage should be trimmed first since the negative voltage tracks the positive side. Pay careful attention to the circuit layout to avoid noise pickup and voltage drops in the lines. The VRE107 series voltage references have the ground terminal brought out on two pins (pin 6 and pin 7) which are connected together internally. This allows the user to achieve greater accuracy when using a socket. Voltage references have a voltage drop across their power supply ground pin due to quiescent current flowing through the contact resistance. If the contact resistance was constant with time and temperature, this voltage drop could be trimmed out. When the reference is plugged into a socket, this source of error can be as high as 20 ppm. By connecting pin 7 to the power supply ground and pin 6 to a high impedance ground point in the measurement circuit, the error due to the contact resistance can be eliminated. If the unit is soldered into place the contact resistance is sufficiently small that it doesn’t effect performance. EXTERNal CONNECTIONS 3. Optional Fine Adjust for approximately ±10mV. PIN CONFIguRaTION TOP VIEW FINE -ADJ. -5V FINE -ADJ. -PS NC REF. GND GND FINE +ADJ. +5V FINE +ADJ. VRE107 +PS NC NC NC 4 VRE107DS P r o d u c t I n n o v a t i o nF r o m VRE107 CONTaCTINg CIRRuS lOgIC SuPPORT For all Apex Precision Power product questions and inquiries, call toll free 800-546-2739 in north America. For inquiries via email, please contact tucson.support@cirrus.com. International customers can also request support by contacting their local Cirrus Logic Sales Representative. To find the one nearest to you, go to www.cirrus.com IMPORTAnT nOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. no responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIn APPLICATIOnS USInG SEMICOnDUCTOR PRODUCTS MAY InVOLVE POTEnTIAL RISKS OF DEATH, PERSOnAL InJURY, OR SEVERE PROPERTY OR EnVIROnMEnTAL DAMAGE (“CRITICAL APPLICATIOnS”). CIRRUS PRODUCTS ARE nOT DESIGnED, AUTHORIZED OR WARRAnTED TO BE SUITABLE FOR USE In PRODUCTS SURGICALLY IMPLAnTED InTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIOnS. InCLUSIOn OF CIRRUS PRODUCTS In SUCH APPLICATIOnS IS UnDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AnD CIRRUS DISCLAIMS AnD MAKES nO WARRAnTY, EXPRESS, STATUTORY OR IMPLIED, InCLUDInG THE IMPLIED WARRAnTIES OF MERCHAnTABILITY AnD FITnESS FOR PARTICULAR PURPOSE, WITH REGARD TO AnY CIRRUS PRODUCT THAT IS USED In SUCH A MAnnER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS In CRITICAL APPLICATIOnS, CUSTOMER AGREES, BY SUCH USE, TO FULLY InDEMnIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AnD OTHER AGEnTS FROM AnY AnD ALL LIABILITY, InCLUDInG ATTORnEYS’ FEES AnD COSTS, THAT MAY RESULT FROM OR ARISE In COnnECTIOn WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs, Apex Precision Power, Apex and the Apex Precision Power logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. VRE107DS