CL-L103-HC3WW1-C

SPECIFICATIONS 1/9 1. Scope of Application These specifications are applied to the chip type LED lamp , model CL-L103-HC3WW1-C 2. Part code C L - L 1 0 3 - H C 3 WW1 - C Series 　　L103 : White power LED for general lighting. Special specifications 　　H : General Color Rendering Index Min. 90 Type. Watt Class 　　C3 : 3 watt package. Lighting color 　　WW1 : Energy Star Correlated Color Temperature 3500(K) Approved Checked Drawn Symbol Name CITILED CL-L103-HC3WW1-C 2010/3/1 Mark Date Issue of first edition Description Appro. Drawing No CITIZEN ELECTRONICS CO.,LTD. Ref.CE-P576 03/10 SPECIFICATIONS 3. Outline drawing Cathode Anode Resin CathodeMark(Gray) 2/9 Tc measuring-point(Board side) Unit： mm Tolerances unless otherwise specified： ±0.3 Anode Cathode Protection Device It has a protection device built in as a protection circuit against static electricity. 4. Performance ( 1 ) Absolute Maximum Rating Parameter Power Dissipation Forward Current Forward Pulse Current Reverse Current Operating Temperature Storage Temperature Symbol PD IF IFP IR TOP TST Rating Value 4.4 420 600 1 -30 ~ +85 -40 ~ +100 Unit W mA mA mA C C *1 120 Tj Max C Junction Temperature *2 *1Forward Current : Duty Product 50pcs/tray < Example of indication label > C US TOM ER 1. TYPE 2. P.No. (Cutomer's P/N) e.g. CL-L103-HC3WW1-C e.g. xxx e.g. 03D001 e.g. 0 : year 2010 e.g. 3 : Mar TYPE P.NO LOT No Q'ty CL-L103-HC3WW1-C xxx 03D001 250 pcs. ---(1) ---(2) ---(3) ---(4) PASS 3. Lot No. - Second letter: Production month by X, Y and Z, respectively. - First letter: Last digit of the year Note: October, November and December are designated - Third letter: CE's control number 4. Quantity e.g. D001 e.g. 250 pieces C ITIZEN ELEC TR ONIC S Approved Checked Drawn Symbol Name CITILED CL-L103-HC3WW1-C 2010/3/1 Mark Date Issue of first edition Description Appro. Drawing No CITIZEN ELECTRONICS CO.,LTD. Ref.CE-P576 03/10 SPECIFICATIONS Precautions 1. Avoid the application of any stress to the lens portion. 2. Avoid any contact by a sharp metal nail or other materials with the lens portion. 8/9 Resin portion 3. This product should be secured firmly by fastening an M3 screw on both sides of the product. Please be careful not to apply any stress to the product during the clamping operation. As the connection status could vary depending on materials of outer heat sink, please check thoroughly. Recommended installation screw pitch M3screw (Insulation) Spring washer (≦φ6mm) Recommended torque : 0.6~0.8N-m Plane washer ( ≦φ6mm) Thermal conductive silicon grease (Insulation paste) Outer heat sink 4. Thermal conductive silicone grease should be applied to the whole rear surface so that this product can dissipate heat as a whole. However, the use of insulating paste is strongly recommended in order to avoid short circuit. This product could be bent during the clamping operation if heat grease in sheet form is used. For this reason, it is recommended that grease in paste form is used. In addition, sufficient insulation should be established between heat sink area of LED package and surface of fixture. (*surface of fixture: exterior of instrument used for dielectric strength test in Electrical Appliance and Material Safety Law.) 5. Handling of static electricity - These products are sensitive to static electricity charge. Please take measures to prevent any static electricity being produced such as the wearing of a wristband or anti-static gloves when handling this product. - All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. - ESD sensitivity of this product is 1000V (HBM, based on JEITA ED-4701/304). - When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. - It is easy to find static-damaged LEDs by a light-on test. Judgmental criterion Condition IF=Max.1mA No-lighting in entire block making up parallel circuit is unacceptable L103 consists of three blocks. Drawn Symbol Name CITILED CL-L103-HC3WW1-C Approved Checked 2010/3/1 Mark Date Issue of first edition Description Appro. Drawing No CITIZEN ELECTRONICS CO.,LTD. Ref.CE-P576 03/10 SPECIFICATIONS Precautions (continued) 6. Please be aware that this product should not come into contact with any other parts in assembled status. 7.Drive circuit - A constant current circuit is recommended as a drive circuit. And when two or more LED packages are connected, the series connection between each package is recommended. - Please design a circuit that prevents any reverse voltage (excess current) from being applied to this product instantaneously when the circuit is ON or OFF. 9/9 8. Heat generation - As this product is designed with consideration of the heat release property of module, a heat release design is required to use this product efficiently. Please ensure that heat generation is not in excess of the absolute maximum rating. (Refer to 4-1 Performance) - Factors responsible for an increase in temperature include heat generation attributed to ambient temperature conditions or power dissipation. Thus, drive conditions should be taken into consideration, depending on ambient temperature (Ta). 9. Recommended soldering - Soldering operation should be performed within 3.5 seconds per land using a soldering iron of 40W or lower. The temperature of a soldering iron should be adjusted 350C or lower. - No external force is applied to sealing resin during soldering operation. - Please do not handle a product until it returns to a normal temperature. Note: This product is not adaptable to reflow process. 10. Other - This product complies with RoHS directives. - This product is intended for the application in general electronic devices (such as office automation equipment, communication devices, audio-video equipment, home electrical appliances, measurement hardware and others). In cases where this product is used for the applications that requires high reliability or could directly affect human life or health due to failure or malfunction (aerospace hardware, medical equipment, atomic control equipment and others), please consult with our sales representatives beforehand. - Our warranty does not cover situations where this product undergoes secondary fabrication such as changes in shape. - An agreement of formal product specifications is required prior to mass production. - The specifications and appearance of this product are subject to change without advanced notice. Approved Checked Drawn Symbol Name CITILED CL-L103-HC3WW1-C 2010/3/1 Mark Date Issue of first edition Description Appro. Drawing No CITIZEN ELECTRONICS CO.,LTD. Ref.CE-P576 03/10