DOCAT052F-010.0M

Available at Digi-Key Surface Mount Oven Stabilized Oscillator DOCAT Series www.digikey.com OCXO or VCOCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Description: Features: Connor-Winfield’s high stability DOCAT Series is an exceptionally precise frequency standard, excellent for use in cellular base stations, test equipment, Synchronous Ethernet and VSAT applications. Based on an AT-cut crystal, the DOCAT Series offers low aging and tight stability in a 9x14mm surface mount package. • OCXO or VCOCXO • 3.3 Vdc Operation • SMT Package • Frequency Stabilities: ±20 ppb, ±50 ppb and ±100 ppb • Temperature Ranges: 0 to 70°C, -20 to 75°C, -40 to 85°C or -40 to 70°C • Low Phase Noise • LVCMOS Output • RoHS Compliant / Lead Free Suggested Pad Layout Package Outline 0.358 (9.1mm) 0.060 (1.52mm) 0.335 Max (8.51mm Max) 0.085 (2.16mm) 1 Side View 0.260 (6.60mm) 0.100 (2.54mm) 0.040 (1.02mm) Top View 4 0.100 (2.54mm) 0.555 (14.1mm) 0.025 (0.64mm) 0.085 (2.16mm) 0.060 (1.52mm) DNC 0.275 (6.99mm) 0.375 (9.52mm) 6 1 DNC = Do Not Connect DNC Bottom View 0.040 (1.02mm) 3 Top 5 View 2 Keep Out Area Dimensional Tolerance: +/-0.005 (0.127mm) Pad Connections 1: N/C or Voltage Control 2: Do Not Connect* 3: Ground 4: Output 5: Do Not Connect* 6: Supply Voltage (Vcc) * Do Not Connect: Pins used for Internal Progamming. Ordering Information DOCAT 02 0 F -024.576M Oscillator Type Frequency Stability Temperature Range Voltage Control Option Output Frequency 3.3 Vdc LVCMOS Output Surface Mount OCXO 02 = ±20 ppb 05 = ±50 ppb 10 = ±100 ppb 0 = 0 to 70°C 1 = -20 to 75°C 2 = -40 to 85°C 3 = -40 to 70°C F = OCXO (Fixed Freq.) V = VCOCXO (Voltage Controlled) Frequency Format -xxx.xM Min * -xxx.xxxxxxM Max * *1 digit min, 6 digits max after the decimal point. Note: Frequency stability ±20 ppb over temperature range -40/85°C is not available in all frequencies. Contact factory for details. Bulletin Page Revision Date Cx275 1 of 4 05 19 Sept 2019 Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/suppport.html 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage - 3.3 Vdc (Vcc) Control Voltage (Vc) Minimum Nominal -55 -0.5 -0.5 - - - Maximum Units Notes 125 4.5 Vcc+0.5 °C Vdc Vdc Operating Specifications Parameter Minimum Nominal Maximum Units Notes -20 -50 -100 - - - 20 50 100 ppb ppb ppb 1 0 -20 -40 -40 -1.0 -20 -20 -10 -0.5 -4.6 3.13 - - - - - - - - - - 3.30 70 75 85 70 1.0 20 20 10 0.5 4.6 3.47 °C °C °C °C ppm ppb ppb ppb/day ppm ppm Vdc - - - - 2.5 1.1 W W - - - - - - - - - 0.25 1.0E-10 - - - 3.0 1.3 0.35 10 60 90 W W ps RMS ms s s 6 Notes Center Frequency (Fo) Frequency Stability vs. Change in Temperature Option 02 Option 05 Option 10 Operating Temperature Range Option 0 Option 1 Option 2 Option 3 Frequency Calibration Frequency Stability vs Load Frequency Stability vs Voltage Aging: Daily Aging: First Year Total Frequency Tolerance (20 Years) Supply Voltage (Vcc) Power Consumption Vcc = Nominal Voltage Commercial Temperature Range: 0 to 70 °C Turn On Steady State @ 25°C Industrial Temperature Range: -40 to 85 °C Turn On Steady State @ 25°C Phase Jitter: (BW: 12 KHz to Fo/2 MHz @ Fo=40.0MHz) Allan Deviation (Tau=1s) Fo=20MHz Start-Up Time (when Vcc ramp < 500us) Warm Up Time (Within Calibration @ 25°C) Warm Up Time (Within Calibration @ -40°C) 10 - 50 MHz 2 ±5% ±5% 3 4 5 CMOS Output Characteristics Parameter Load Output Voltage Output Voltage: High (Voh) Low (Vol) Output Current: High (Ioh) Low (Iol) Duty Cycle at 50% of Vcc Rise / Fall Time: 10% to 90% Minimum Nominal Maximum Units 2.7 - -4 - 45 - - - - - 50 - - 0.3 - 4 55 6.5 V V mA mA % ns - 15 - pF 7 Typical Phase Noise Characteristics Parameter @ 1 Hz offset @ 10 Hz offset @ 100 Hz offset @ 1 KHz offset @ 10 KHz offset @ 100 KHz offset @ 1MHz offset Fo=10 MHz -72 -100 -128 -145 -151 -154 -155 Fo=24.576MHz -70 -96 -125 -145 -151 -154 -155 Fo=40.0MHz -67 -90 -116 -139 -147 -153 -153 Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Units dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. © Copyright 2019 The Connor-Winfield Corporation Not intended for life support applications. Notes Cx275 2 of 4 05 19 Sept 2019 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Input Characteristics - Voltage Controlled Option Parameter Control Voltage Range: Frequency Pullability: Input Impedance Linearity Minimum 0.30 ±10.0 100K - Nominal 1.65 - - - Maximum 3.00 ±15.0 - ±5 Units V ppm Ohms % Notes 8 9 Package Characteristics DOC Package Package consisting of a FR-4 substrate and Ryton-R-4 cover. Water Resistant package, non-hermetic seal. (Engineering Properties of Ryton R-4 Application Note AN2100) Environmental Characteristics Shock 500 G’s 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D. Sinusoidal Vibration 0.06” D.A. or 10G’s Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A. Random Vibration 5.35 G’s rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis. Moisture 10 cycles, 95% RH, Per MIL-STD-202G, Method 112. Marking Permanency Per MIL-STD-202G, Method 215J. Solder Process Recommendations: RoHS compliant, lead free. See solder profile on page 4. In-line reflow: Refer to recommended reflow pre-heat and reflow temperatures on page 4. Package material consist of Ryton R-4 high temperature cover with FR4 substrate. Component solder is Pb free high temperature eutectic alloy with a melting point of 221°C. In-line oven profile: We recommend using KIC profiler or similar device placing one of the thermocouples on the device to insure that the internal package temperature does not exceed 221°C. Removal of device: If for any reason the device needs to be removed from the board, use a temperature controlled repair station with profile monitoring capabilities. Following a monitored profile will insure the device is properly pre-heated prior to reflow. Refer to IPC 610E for inspection guidelines. Recommended Cleaning Process: (If required) Device is non-hermetic, water resistance with four weep holes, one in each corner to allow moisture to be removed during the drying cycle. We recommend in-line warm water wash with air knife and drying capabilities. If cleaner does not have drying capability, then use hot air circulated oven. Boards should be placed in the oven vertically for good water runoff. Device must be dried properly prior to use! Note: If saponifier is used make sure the device is rinsed properly to insure all residues are removed. PH of saponifier should not exceed 10. Drying Temperature: Between 85 to 100°C. Drying Time: Time will vary depending on the board size. Caution: Do not submerge the device! Notes: 1. Frequency stability vs. change in temperature. [±(Fmax - Fmin)/(2*Fo)]. 2. Initial calibration @ 25°C. For OCXO with voltage control option, the control voltage must be fixed. 3. After 10 days of operation 4. Inclusive of calibration @ 25°C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), shock and vibration and 20 years aging 5. Minimum "Power On Time" after rail rises from 0 to within +/-5% of Vcc = 1 second. Supply must Supply voltage must reach Vcc level monotonically. 6. 10ms start time is guaranteed when supply voltage reaches Vcc level in