OH200-51003CF-005.0M

Available at Digi-Key** www.digikey.com Stratum 3E High Stability Oven Stabilized Oscillator OH200-Series OCXO / VCOCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Features Connor-Winfield’s high stability OH200- series are exceptionally precise frequency standards, excellent for use in cellular base stations, test equipment, Synchronous Ethernet, VSAT and Stratum 3E applications These unique OCXO / VCOCXO oscillator products provide temperature stabilities in the range of ±3 ppb to ±25 ppb, over the commercial, extended commercial or the industrial temperature range. Power requirements are 3W over the commercial temperature range and 4.5W over the industrial temperature range. Additionally, excellent aging is achieved through the use of overtone SC cut crystals. The OH200 series is available with CMOS logic or Sinewave output along with Voltage Controlled option. These oscillators provide outstanding phase noise that varies depending on frequency. Frequencies are available from 5.0 to 40.0 MHz. Allan Variance specifications are rated for primary reference standards. Warm up times are on the order of 5 minutes to 0.10 ppm of final frequency. • Frequency Range: 5.0 to 40.0 MHz • OCXO - Fixed Frequency • VCOCXO - Voltage Controlled Option • 3.3 Vdc, 5.0 Vdc or 12.0 Vdc Operation • Available Frequency Stabilities: ±3 ppb, ±5 ppb, ±10 ppb or ±25 ppb • Available Temperature Ranges: 0 to 70°C, -20 to 70°C, -40 to 70°C or -40 to 85°C • Low Phase Noise / Phase Jitter • Available Outputs: CMOS or Sinewave • Package: 1.1" x 1.4" x 0.5" (CO-8) • RoHS Compliant / Lead Free 32 12 F 3C 00 61 Hz 0- M 20 2.8 12 OH 1 90 78 56 34 12 Phone: 630- 851- 4722 Description Ordering Information OH200Package OH200- = 1.1x1.4 CO8 6 10 03 C Temperature Range Frequency Stability 06 = ±3 ppb * 10 = ±5 ppb * 20 = ±10 ppb 50 = ±25 ppb Supply Voltage Output Type OCXO Type 03 = 3.3 Vdc 05 = 5.0 Vdc 12 = 12.0 Vdc C = CMOS S = Sinewave F = Fixed Freq. V = Voltage Controlled Option 5 = 0 to 70°C 6 = -40 to 85°C 7 = -20 to 70°C 8 = -40 to 70°C F {±(Fmax-Fmin)/(2*Fo)} - 012.8M Output Frequency Frequency Format -xxx.xM Min -xxx.xxxxxxM Max *Min 1 and Max 6 digits after the decimal point. M = MHz * Frequency stability option 06 is only available for temperature ranges 0 to 70°C and -20 to 70°C. * Frequency stability options 06 and 10 are only available at frequencies less than or equal to 25MHz. Bulletin Page Revision Date Cx193 1 of 4 14 24 April 2018 Example Part Number: OH200-61003CF-012.8M = 1.1" x 1.4" x 0.5" CO-8 package, -40 to 85°C temperature range, ±5.0 ppb frequency stability, 3.3 Vdc supply voltage, CMOS square wave output, fixed frequency OCXO, 12.8 MHz output frequency. To order a OH200-61003CF with an output frequency of: 6.4 MHz = OH200-61003CF-006.4M To order a OH200-61003CF with an output frequency of 16.384 MHz = OH200-61003CF-016.384M. OH200-72005SV-040.0M = 1.1" x 1.4" x 0.5" CO-8 package, -20 to 70°C temperature range, ±10.0 ppb frequency stability, 5.0 Vdc supply voltage, Sinewave output, voltage controlled output frequency VCOCXO, 40 MHz output frequency. Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/support.html 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Control Voltage (Vc) Operating Supply Voltage 3.3 Vdc (Vcc) Operating Supply Voltage 5.0 Vdc (Vcc) Operating Supply Voltage 12 Vdc (Vcc) Minimum -55 -0.5 -0.5 3.13 4.75 11.40 Nominal - - - 3.30 5.00 12.00 Maximum 125 13.5 7.0 3.47 5.25 12.60 Units °C Vdc Vdc Vdc Vdc Vdc Notes Absolute Ratings: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only. The functional operation of the device at those or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to conditions outside the "recommended operating conditions" for any extended period of time may adversely impact device reliability and result in failures not covered by warranty. Operating Specifications Parameter Center Frequency: (Fo) Operating Temperature Range: T emperature Code 5 T emperature Code 6 T emperature Code 7 T emperature Code 8 Frequency Calibration: Frequency Stability vs. Change in Temperature: S tability Code 06 S tability Code 10 S tability Code 20 S tability Code 50 Frequency Stability vs. Load Frequency Stability vs. Voltage Aging: Daily: 5 MHz to 20 MHz > 20 MHz to 40 MHz Aging: First Year: 5 MHz to 20 MHz >20 MHz to 40 MHz Lifetime Tolerance: (20 Years) 5 MHz to 20 MHz- > 20 MHz to 40 MHz Supply Voltage: (Vcc) V oltage Code 03 V oltage Code 05 V oltage Code 12 Power Consumption: Turn-On 0 to 70°C Models - 20 to 70°C Models - 20 to 75°C Models - 40 to 85°C Models Power Consumption: Steady State @ 25°C 0 to 70°C Models - 20 to 70°C Models - 20 to 75°C Models - 40 to 85°C Models Phase Jitter: (BW: 10 Hz to Fo/2) Models with Fo: 5 MHz to 20 MHz Models with Fo: >20 MHz to 40 MHz Short Term Allan Deviation (1s) Start-Up Time: Warm Up Time @ 25°C: Minimum Nominal Maximum 0 -40 -20 -40 -0.1 - - - - - 70 85 70 70 0.1 °C °C °C °C ppm @ 25°C -3.0 -5.0 -10.0 -25.0 -5.0 -5.0 - - - - - - 3.0 5.0 10.0 25.0 5.0 5.0 ppb ppb ppb ppb ppb ppb 1 1 1 1 ±5% ±5% -1.0 -2.0 - - 1.0 2.0 ppb/day ppb/day 2 2 -50 -100 - - 50 100 ppb ppb -300 -500 - - 300 500 ppb ppb 3 3 3.13 4.75 11.40 3.30 5.00 12.00 3.47 5.25 12.60 Vdc Vdc Vdc 4 4 4 - - - - - - - - 3.00 3.20 3.30 3.80 W W W W 5 5 5 5 - - - - - - - - 1.10 1.10 1.20 1.50 W W W W 5 5 5 5 - - - - - - - 1.0E-11 - - 1.0 2.0 - 500 5 ps rms ps rms rms ms minutes 6 5.0 - 40.0 Notes: 1. Frequency stability vs. change in temperature [±(Fmax-Fmin)/(2*Fo)]. Stability option 06 is not available for temperature ranges -40/70°C and -40/85°C. Stability options 06 and 10 are not available for frequencies >25MHz. 2. At time of shipment after 48 hours of operation. 3. Inclusive of calibration, operating temperature, supply voltage change, load change and 20 years aging. 4. Supply voltage must reach Vcc levels monotonically within a ramp-up time of