CVCSO-914-245.760

CVCSO-914 Model 9×14 mm SMD, 5.0V, SineWave Ultra-Low Phase Noise True SineWave SAW Based VCSO CVCSO-914-800 Model CVCSO-914 is a voltage-controlled SAW (surface acoustic wave) Clock Oscillator (VCSO). SAW crystal technology provides low-noise and low-jitter performance with true sinewave output. Features include -135 dBc/Hz phase noise at 10 kHz offset at 1 GHz, 5V input voltage, and 9×14 mm SMT package. The oscillator has no sub-harmonic and the second harmonic is typically -20 dBc. Applications include PLL frequency translation, test and measurement, avionics, point-to-point radios, and multi-point radios. Rev: X Date: 02-Feb-2022 Page 1 of 4 C CRYSTEK CORPORATION 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com Ultra-Low Phase Noise True SineWave SAW Based VCSO CVCSO-914 Model 9×14 mm SMD, 5.0V, SineWave Frequency Range: Temperature Range: CVCSO-914A option CVCSO-914E option CVCSO-914M option CVCSO-914X option Storage: Input Voltage: Control Voltage Range: Tuning Sensitivity (Kv): Settability At Nominal (25°C): Frequency vs Temperature: Input Current: 500.000 MHz to 1000 MHz 0°C to +70°C 0°C to +50°C 0°C to +85°C -20°C to +70°C -40°C to +85°C -40°C to 90°C 5.0V ±0.25V 0V to 5.0V +120 ppm/V Typical 1.5V +0.5V -1.0V ±200ppm Typical 25mA Typical, 35mA Max Output: Pullability APR: Linearity: Output Power: Start-Up Time: 2nd Harmonic: Sub-Harmonics: Modulation BW: True SineWave ±50ppm Min ±20% Max +10dBm Min into 50 Ω Load 2ms Typical, 10ms Max -20dBc Typical, -15dBc Max None >20kHz @ -3dB G-sensitivity: Weight: 0.9×10-9 per G 0.816 g 0.090 (2.29) 0.040 (1.01) 1 2 4 3 SUGGESTED PAD LAYOUT 0.050 (1.27) 0.560 ±0.005 (14.2 ±0.127) 0.360 ±0.005 (9.14 ±0.127) 0.090 (2.29) CRYSTEK CVCSO-914 Frequency Date Code 0.180 (4.57) 0.125 (3.18) 0.560 ±0.005 (14.2 ±0.127) 0.040 (1.02) 0.050 (1.27) 0.280 (7.11) 0.200 (5.08) 0.200 (5.08) See Table A PAD FINISH: Immersion Gold (ENIG); 5 micro inches maximum Package Height Options (Max) inches mm Standard 0.210 5.33 Option L 0.135 3.43 Table A C 0.100 (2.54) 0.280 (7.11) CRYSTEK CORPORATION Pad Connection 1 2 3 4 Volt. Control GND Output Vdd Rev: X Date: 02-Feb-2022 Page 2 of 4 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com Ultra-Low Phase Noise True SineWave SAW Based VCSO CVCSO-914 Model 9×14 mm SMD, 5.0V, SineWave Crystek Part Number Guide Available Frequencies (MHz): 640.000 916.000 800.000 1000.000 840.000 CVCSO - 914 X L - 640.000 #1 #2 #3 #4 #5 #1 Crystek Saw Voltage Controlled Oscillator #2 Model 914 #3 Temperature Range (X = -40/85°C) (M = -20/70°C) (Blank = 0/70°C) #4 Height (L = 0.135") (Blank = 0.210") #5 Frequency in MHz: 3 or 6 decimal places Custom Frequencies Available with NRE Fee Frequency vs Temperature RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. Critical Temperature Zone TEMPERATURE 260°C Ramp-Down 6°C/Sec. 217°C 200°C 150°C Preheat 180 Secs. Max. 90 Secs. Max. 8 Minutes Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. Parameter MIL-STD-883, Method 2002, Condition B Mechanical Vibration MIL-STD-883, Method 2007, Condition A Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition I or J Thermal Shock MIL-STD-883, Method 1011, Condition A Moisture Resistance MIL-STD-883, Method 1004 Crystek Corporation reserves the right to make changes to its products and/or information contained herein without notice. No liability is assumed as a result of its use or application. C Conditions Mechanical Shock CRYSTEK CORPORATION Rev: X Date: 02-Feb-2022 Page 3 of 4 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com CVCSO-914 Model 9×14 mm SMD, 5.0V, SineWave Ultra-Low Phase Noise True SineWave SAW Based VCSO CVCSO-914-640 Rev: X Date: 02-Feb-2022 Page 4 of 4 C CRYSTEK CORPORATION 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com