VRB3-D48-S12-DIP

1/3 VRB3-DIP Series Dc-Dc Converter Rev. 12-2006 Features ·Wide (2:1) input range ·Isolated & regulated 3W output ·Efficiency up to 83% ·Single voltage output ·DIP package style ·Industry standard pinout ·metal case ·No heatsink required ·1K Vdc isolation ·MTBF >1,000,000 hours ·Temperature range: -40°C~+85°C ·RoHS Compliant Model Number VRB3-D5-S5-DIP VRB3-D5-S9-DIP VRB3-D5-S12-DIP VRB3-D5-S15-DIP VRB3-D12-S5-DIP VRB3-D12-S9-DIP VRB3-D12-S12-DIP VRB3-D12-S15-DIP VRB3-D24-S5-DIP VRB3-D24-S9-DIP VRB3-D24-S12-DIP VRB3-D24-S15-DIP VRB3-D48-S5-DIP VRB3-D48-S9-DIP VRB3-D48-S12-DIP VRB3-D48-S15-DIP Nominal 5 Vdc 5 Vdc 5 Vdc 5 Vdc 12 Vdc 12 Vdc 12 Vdc 12 Vdc 24 Vdc 24 Vdc 24 Vdc 24 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc Input Voltage Range 4.5~9 Vdc 4.5~9 Vdc 4.5~9 Vdc 4.5~9 Vdc 9~18 Vdc 9~18 Vdc 9~18 Vdc 9~18 Vdc 18~36 Vdc 18~36 Vdc 18~36 Vdc 18~36 Vdc 36~72 Vdc 36~72 Vdc 36~72 Vdc 36~72 Vdc Max. 11 Vdc 11 Vdc 11 Vdc 11 Vdc 22 Vdc 22 Vdc 22 Vdc 22 Vdc 40 Vdc 40 Vdc 40 Vdc 40 Vdc 80 Vdc 80 Vdc 80 Vdc 80 Vdc Output Voltage 5 Vdc 9 Vdc 12 Vdc 15 Vdc 5 Vdc 9 Vdc 12 Vdc 15 Vdc 5 Vdc 9 Vdc 12 Vdc 15 Vdc 5 Vdc 9 Vdc 12 Vdc 15 Vdc Output Current Max. 600 mA 330 mA 250 mA 200 mA 600 mA 330 mA 250 mA 200 mA 600 mA 330 mA 250 mA 200 mA 600 mA 330 mA 250 mA 200 mA Min. 60 mA 33 mA 25 mA 20 mA 60 mA 33 mA 25 mA 20 mA 60 mA 33 mA 25 mA 20 mA 60 mA 33 mA 25 mA 20 mA Efficiency 70% 72% 73% 75% 70% 75% 76% 78% 70% 75% 81% 81% 78% 82% 82% 83% Package Style DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP General Specifications Output short circuit protection Temperature rise at full load Cooling No-load power consumption Operating temperature range Storage temperature range Soldering temperature Storage humidity range Case material MTBF continuous 30°C typ. Free air convection 100 mW (typ.) -40°C to +85°C -55°C to +125°C 300°C max. 1,000,000 hrs. Isolation Specifications Item I solation Voltage Isolation Resistance Test Conditions Min. Flash tested for 1 min. 1500 Vdc Test at 500 Vdc 1000 M Ω Typ. Max. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 2/3 VRB3-DIP Series Dc-Dc Converter Rev. 12-2006 Output Specifications Item Output power Line Regulation Load Regulation Output voltage accuracy Temperature drift Ripple Noise Switching frequency Test conditions See below Input voltage from low to high From 10% to 100% load refer to recommended circuit refer to recommended circuit 20 Hz-300 KHz Bandwidth DC-20MHz Bandwidth 100% load 10% load Min. 0.3 W Typ. ±0.2% ±0.5% ±1% 30 mVp-p 80 mVp-p 80 KHz 250 KHz Max. 3W ±0.5% ±0.75% ±3% 0.03%/°C 60 mVp-p 150 mVp-p 300 KHz 600 KHz Notes: 1. All specifications measured at TA=25 °C, humidity 1500VDC; 3) The output load’s actual power consumption is less than 1W. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 3/3 VRB3-DIP Series Dc-Dc Converter Rev. 12-2006 Typical Characteristics Temperature Derating Graph Cin Vin Vout DC DC 0V GND Input Current(A) Ip Operating Temp.( C ) Pin Connections Bottom View Input Voltage Range Pin 2,3 GND NC +Vo 0V Vin Vin 9,10,11,15 14 16 Input Voltage (V) 23 9 1011 External Capacitor Although this series of DC/DC converter can work without external capacitor, in order to keep an optimum performance, however, it needs external capacitor. (See Table 1) Requirement on Output Load 2322 16 1514 22 23 Outline Dimensions & Recommended Footprint Details 31.80 0.50 20.30 23 22 1615 14 To ensure this module operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a 9.45 MP:10.5 maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum out put load is not less than 1 0% Of the full load, and that this product s hould never be operated under no load!!! If the actual load is less below the specified minimum load. the output ripple of this type of DC/DC converter will increase drastically and at the same time efficiency & reliability of the circuit will 23 9 10 11 15.24 2.54 22.86 2 x 2.54 4.00 decrease deeply .If the actual output power from the load in your circuit is very small. please connect a resistor with proper resistance at the output end to in parallel to increase the load, or use our company’s other products with a lower rated output power. The products cannot be used in parallel. Table 1 (Bottom View) (Side View) Note: All Pins on a 2.54mm pitch; All Pin diameters are 0.50 mm(Tolerance:±0.10); All dimensions in mm. Application Note Recommended circuit All the VRB3-DIP Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load. Never be tested under no load (See Figure 1 & 2). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high.(See table 1).If you want to use the products in high EMI, please choose our metal packaged products. Input Current When it is used in unregulated power supply., be sure that the fluctuating range of the power supply and the rippled voltage do not exceed the module standard. Input current of power supply should afford the startup current of this kind of DC/DC module. (See figure 2) Vin 5V & 12V 24V & 48V Cin 100uF Cout (0+70°C) 100uF (electrolytic capacitor) Cout (-40+85°C) 47uF (tantalum capacitor) 10uF V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258