CY28405
CK409-Compliant Clock Synthesizer
Features
• Three differential CPU clock pairs
• Supports Intel Springdale/Prescott (CK409)
• Selectable CPU frequencies
• Dial-A-Frequency®
• Supports SMBus/I2C Byte, Word, and Block Read/Write
• Ideal Lexmark Spread Spectrum profile for maximum
electromagnetic interference (EMI) reduction
• 3.3V power supply
• Nine copies of PCI clock
• Four copies 3V66 clock with one optional VCH
• 48-pin SSOP package
CPU
3V66
PCI
REF
48M
• Two copies REF clock
x3
x4
x9
x2
x2
Block Diagram
Pin Configuration
• Two copies 48-MHz USB clock
XIN
XOUT
XTAL
OSC
Divider
Network
IREF
SELVCH
PLL2
2
MODE
PD#
USB_48
SDATA
SCLK
I2C
Logic
WD
Timer
Cypress Semiconductor Corporation
Document #: 38-07512 Rev. *B
3901 North First Street
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
VDDA
VSSA
IREF
CPUT_ITP
CPUC_ITP
VSS_CPU
CPUT1
CPUC1
VDD_CPU
CPUT0
CPUC0
VSS
DNC***
DNC***
VDD
VTT_PWRGD#
SDATA
SCLK
3V66_0
3V66_1
VSS_3V66
VDD_3V66
3V66_2/MODE*
3V66_3/VCH/SELVCH**
SSOP-48
* 150k Internal Pull-up
** 150k Internal Pull-down
*** Do Not Connect
RESET#
•
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CY28405
FS_[A:E]
VTT_PWRGD#
PLL Ref Freq
~
PLL 1
**FS_A/REF_0
**FS_B/REF_1
VDD_REF
VDD_REF
REF[0:1]
XIN
XOUT
VDD_CPU
VSS_REF
CPUT[0:1,ITP], CPUC[0:1,ITP]
*FS_C/PCIF0
*FS_D/PCIF1
*FS_E/PCIF2
VDD_PCI
VSS_PCI
PCI0
PCI1
VDD_3V66
3V66_[0:2]
PCI2
PCI3
VDD_PCI
VDD_PCI
PCIF[0:2]
VSS_PCI
PCI[0:5]
PCI4
PCI5
RESET#/PD#
DOT_48
3V66_3/VCH
USB_48
VSS_48
VDD_48MHz
VDD_48
DOT_48
•
San Jose, CA 95134
•
408-943-2600
Revised June 16, 2004
CY28405
Pin Description
Pin No.
1, 2
Name
REF(0:1)
Type
O, SE
Description
Reference Clock. 3.3V 14.318-MHz clock output.
1, 2, 7, 8, 9 FS_A, FS_B, FS_C,
FS_D, FS_E
I
3.3V LVTTL latched input for CPU frequency selection.
4
XIN
I
Crystal Connection or External Reference Frequency Input. This pin
has dual functions. It can be used as an external 14.318-MHz crystal
connection or as an external reference frequency input.
5
XOUT
O, SE
Crystal Connection. Connection for an external 14.318-MHz crystal
output.
39, 42, 45
CPUT(0:1,ITP)
O, DIF
CPU Clock Output. Differential CPU clock outputs.
38, 41, 44
CPUC(0:1,ITP)
O, DIF
CPU Clock Output. Differential CPU clock outputs.
36, 35
DNC
30, 29
3V66(0:1)
O, SE
66-MHz Clock Output. 3.3V 66-MHz clock from internal VCO.
25
3V66_3/VCH/SELVCH
I/O, SE
PD
48- or 66-MHz Clock Output. 3.3V selectable through external SELVCH
strapping resistor and SMBus to be 66-MHz or 48-MHz. Default is 66-MHz.
0 = 66 MHz, 1 = 48 MHz
26
3V66_2/MODE
I/O, SE
PU
66-MHz Clock Output. 3.3V 66-MHz clock from internal VCO. Reset or
Power-down Mode Select. Selects between RESET# output or PWRDWN#
input for the PWRDWN#/RESET# pin. Default is RESET#. 0 = PD#, 1 =
RESET
7, 8, 9
PCIF(0:2)
O, SE
Free Running PCI Output. 33-MHz clocks divided down from 3V66.
12, 13, 14, PCI(0:5)
15, 18, 19
O, SE
PCI Clock Output. 33-MHz clocks divided down from 3V66.
Do Not Connect.
22
USB_48
O, SE
Fixed 48-MHz clock output.
21
DOT_48
O, SE
Fixed 48-MHz clock output.
46
IREF
20
RESET#/PD#
33
VTT_PWRGD#
I
Current Reference. A precision resistor is attached to this pin which is
connected to the internal current reference.
I/O, PU
3.3V LVTTL input for Power-down# active LOW. Watchdog Timeout
Reset Output
I
3.3V LVTTL input is a level sensitive strobe used to latch the FS[A:E]
input (active LOW).
32
SDATA
I/O
31
SCLK
I
48
VDDA
PWR
3.3V Power supply for PLL.
47
VSSA
GND
Ground for PLL.
3, 10, 16, VDD(REF,PCI,48,3V66,C
24, 27, 34, PU,ITP)
40
PWR
3.3V Power supply for outputs.
6, 11, 17, VSS(REF,PCI,48,3V66,
23, 28, 37, CPU,ITP)
43
GND
Ground for outputs.
Document #: 38-07512 Rev. *B
SMBus compatible SDATA.
SMBus compatible SCLOCK.
Page 2 of 19
CY28405
MODE Select
Frequency Select Pins
The hardware strapping MODE input pin can be used to select
the functionality of the RESET#/PD# pin. The default (internal
pull up) configuration is for this pin to function as a RESET#
Watchdog output. When pulled LOW during device power-up,
the RESET#/PD# pin will be configured to function as a Power
Down input pin.
Host clock frequency selection is achieved by applying the
appropriate logic levels to FS_A through FS_E inputs prior to
VTT_PWRGD# assertion (as seen by the clock synthesizer).
Upon VTT_PWRGD# being sampled low by the clock chip
(indicating processor VTT voltage is stable), the clock chip
samples the FS_A through FS_E input values. For all logic
levels of FS_A through FS_E, VTT_PWRGD# employs a
one-shot functionality in that once a valid low on
VTT_PWRGD# has been sampled, all further VTT_PWRGD#
and FS_A through FS_E transitions will be ignored.
Table 1. Frequency Selection Table
Input Conditions
Output Frequency
FS_E
FS_D
FS_C
FS_B
FS_A
FSEL_4
FSEL_3
FSEL_2
FSEL_1
FSEL_0
CPU
3V66
PCI
VCO Freq.
PLL Gear
Constants
(G)
0
0
0
0
0
100.7
67.1
33.6
805.6
24004009.32
0
0
0
0
1
100.2
66.8
33.4
801.6
24004009.32
0
0
0
1
0
108.0
72.0
36.0
864.0
24004009.32
0
0
0
1
1
101.2
67.5
33.7
809.6
24004009.32
0
0
1
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
1
0
1
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
1
1
0
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
1
1
1
Reserved
Reserved
Reserved
Reserved
Reserved
0
1
0
0
0
125.7
62.9
31.4
754.2
32005345.76
0
1
0
0
1
130.3
65.1
32.6
781.6
32005345.76
0
1
0
1
0
133.6
66.8
33.4
801.6
32005345.76
0
1
0
1
1
134.2
67.1
33.6
805.2
32005345.76
0
1
1
0
0
134.5
67.3
33.6
807.0
32005345.76
0
1
1
0
1
148.0
74.0
37.0
888.0
32005345.76
0
1
1
1
0
Reserved
Reserved
Reserved
Reserved
Reserved
0
1
1
1
1
Reserved
Reserved
Reserved
Reserved
Reserved
1
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
1
0
0
0
1
Reserved
Reserved
Reserved
Reserved
Reserved
1
0
0
1
0
167.4
55.8
27.9
669.6
48008018.65
1
0
0
1
1
170.0
56.7
28.3
680.0
48008018.65
1
0
1
0
0
175.0
58.3
29.2
700.0
48008018.65
1
0
1
0
1
180.0
60.0
30.0
720.0
48008018.65
1
0
1
1
0
185.0
61.7
30.8
740.0
48008018.65
1
0
1
1
1
190.0
63.3
31.7
760.0
48008018.65
1
1
0
0
0
100.9
67.3
33.6
807.2
24004009.32
1
1
0
0
1
133.9
67.0
33.5
803.4
32005345.76
1
1
0
1
0
200.9
67.0
33.5
803.6
48008018.65
1
1
0
1
1
Reserved
Reserved
Reserved
Reserved
Reserved
1
1
1
0
0
100.0
66.7
33.3
800.0
24004009.32
1
1
1
0
1
133.3
66.7
33.3
800.0
32005345.76
1
1
1
1
0
200.0
66.7
33.3
800.0
48008018.65
1
1
1
1
1
Reserved
Reserved
Reserved
Reserved
Reserved
Document #: 38-07512 Rev. *B
Page 3 of 19
CY28405
Serial Data Interface
Data Protocol
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions, such as individual
clock output buffers, can be individually enabled or disabled.
The registers associated with the Serial Data Interface
initializes to their default setting upon power-up, and therefore
use of this interface is optional. The interface can also be
accessed during power-down operation.
The clock driver serial protocol accepts Byte Write, Byte Read,
Block Write and Block Read operation from any external I2C
controller. For Block Write/Read operation, the bytes must be
accessed in sequential order from lowest to highest byte (most
significant bit first) with the ability to stop after any complete
byte has been transferred. For Byte Write and Byte Read
operations, the system controller can access individual
indexed bytes. The offset of the indexed byte is encoded in the
command code, as described in Table 2.
The Block Write and Block Read protocol is outlined in Table 3
while Table 4 outlines the corresponding Byte Write and Byte
Read protocol. The slave receiver address is 11010010 (D2h).
Table 2. Command Code Definition
Bit
Description
7
0 = Block Read or Block Write operation
1 = Byte Read or Byte Write operation
(6:0)
Byte offset for Byte Read or Byte Write operation. For Block Read or Block Write operations, these bits
should be ‘0000000’
Table 3. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
Block Read Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
11:18
19
20:27
28
29:36
37
38:45
Command Code – 8-bit ‘00000000’ stands for
block operation
11:18
Command Code – 8-bit ‘00000000’ stands for
block operation
Acknowledge from slave
19
Acknowledge from slave
Byte Count – 8 bits
20
Repeat start
Acknowledge from slave
Data byte 0 – 8 bits
Acknowledge from slave
Data byte 1 – 8 bits
46
Acknowledge from slave
....
Data Byte N/Slave Acknowledge...
....
Data Byte N – 8 bits
....
Acknowledge from slave
....
Stop
Document #: 38-07512 Rev. *B
21:27
Slave address – 7 bits
28
Read
29
Acknowledge from slave
30:37
38
39:46
47
48:55
Byte count from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
56
Acknowledge
....
Data bytes from slave/Acknowledge
....
Data byte N from slave – 8 bits
....
Not Acknowledge
....
Stop
Page 4 of 19
CY28405
Table 4. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
1
2:8
9
10
11:18
19
20:27
Byte Read Protocol
Description
Bit
Start
1
Slave address – 7 bits
2:8
Write = 0
Acknowledge from slave
Command Code – 8 bits
‘1xxxxxxx’ stands for byte operation, bits[6:0] of
the command code represents the offset of the
byte to be accessed
Acknowledge from slave
29
Stop
Write = 0
10
Acknowledge from slave
19
Data byte from master – 8 bits
28
Slave address – 7 bits
9
11:18
Acknowledge from slave
Description
Start
20
21:27
Command Code – 8 bits
‘1xxxxxxx’ stands for byte operation, bits[6:0]
of the command code represents the offset of
the byte to be accessed
Acknowledge from slave
Repeat start
Slave address – 7 bits
28
Read = 1
29
Acknowledge from slave
30:37
Data byte from slave – 8 bits
38
Not Acknowledge
39
Stop
Byte 0: Control Register 0
Bit
@Pup
7
0
Name
Description
6
1
PCIF
PCI
PCI Drive Strength Override
0 = Force All PCI and PCIF Outputs to Low Drive Strength
1= Force All PCI and PCIF Outputs to High Drive Strength
5
0
Reserved
Reserved, Set= 0
4
HW
FS_E
Power up latched value of FS_E pin
3
HW
FS_D
Power up latched value of FS_D pin
2
HW
FS_C
Power up latched value of FS_C pin
1
HW
FS_B
Power up latched value of FS_B pin
0
HW
FS_A
Power up latched value of FS_A pin
Reserved, Set= 0
Byte 1: Control Register 1
Bit
@Pup
Name
7
0
Reserved
Reserved, set = 0
6
1
Reserved
Reserved, set = 1
5
1
Reserved
Reserved, set = 1
4
1
Reserved
Reserved, set = 1
3
1
Reserved
Reserved, set = 1
2
1
CPUT_ITP, CPUC_ITP
CPUT/C_ITP Output Enable
0 = Disabled (three-state), 1 = Enabled
1
1
CPUT1, CPUC1
CPU(T/C)1 Output Enable,
0 = Disabled (three-state), 1 = Enabled
0
1
CPUT0, CPUC0
CPU(T/C)0 Output Enable
0 = Disabled (three-state), 1 = Enabled
Document #: 38-07512 Rev. *B
Description
Page 5 of 19
CY28405
Byte 2: Control Register 2
Bit
@Pup
7
0
Reserved
Name
Description
6
0
Reserved
Reserved, set = 0
5
0
CPUT_ITP, CPUC_ITP
CPUT/C_ITP Pwrdwn drive mode
0 = Driven in power- down, 1 = three-state
4
0
CPUT1, CPUC1
CPU(T/C)1 Pwrdwn drive mode
0 = Driven in power-down, 1 = three-state
3
0
CPUT0, CPUC0
CPU(T/C)0 Pwrdwn drive mode
0 = Driven in power-down, 1 = three-state
2
0
Reserved
Reserved
1
0
Reserved
Reserved
0
0
Reserved
Reserved
Reserved, set = 0
Byte 3: Control Register 3
Bit
@Pup
Name
Description
7
1
SW PCI_STP Function
0= PCI_STP assert, 1= PCI_STP deassert
When this bit is set to 0, all STOPPABLE PCI and PCIF outputs will be
stopped in a synchronous manner with no short pulses.
When this bit is set to 1, all STOPPED PCI and PCIF outputs will resume
in a synchronous manner with no short pulses.
6
1
Reserved
Reserved
5
1
PCI5
PCI5 Output Enable
0 = Disabled, 1 = Enabled
4
1
PCI4
PCI4 Output Enable
0 = Disabled, 1 = Enabled
3
1
PCI3
PCI3 Output Enable
0 = Disabled, 1 = Enabled
2
1
PCI2
PCI2 Output Enable
0 = Disabled, 1 = Enabled
1
1
PCI1
PCI1 Output Enable
0 = Disabled, 1 = Enabled
0
1
PCI0
PCI0 Output Enable
0 = Disabled, 1 = Enabled
Byte 4: Control Register 4
Bit
@Pup
Name
7
0
USB_48
USB 48 Drive Strength Control
0 = High Drive Strength, 1 = Low Drive Strength
6
1
USB_48
USB_48 Output Enable
0 = Disabled, 1 = Enabled
5
0
PCIF2
Allow control of PCIF2 with assertion of SW PCI_STP
0 = Free Running, 1 = Stopped with SW PCI_STP
4
0
PCIF1
Allow control of PCIF1 with assertion of SW PCI_STP
0 = Free Running, 1 = Stopped with SW PCI_STP
3
0
PCIF0
Allow control of PCIF0 with assertion of SW PCI_STP
0 = Free Running, 1 = Stopped with SW PCI_STP
2
1
PCIF2
PCIF2 Output Enable
0 = Disabled, 1 = Enabled
1
1
PCIF1
PCIF1 Output Enable
0 = Disabled, 1 = Enabled
0
1
PCIF0
PCIF0 Output Enable
0 = Disabled, 1 = Enabled
Document #: 38-07512 Rev. *B
Description
Page 6 of 19
CY28405
Byte 5: Control Register 5
Bit
@Pup
Name
Description
7
1
DOT_48
6
1
Reserved
Reserved
5
HW
3V66_3/VCH/SELVCH
3V66_3/VCH/SELVCH Frequency Select
0 = 3V66 mode, 1 = VCH (48MHz) mode
May be written to override the power-up value.
4
1
3V66_3/VCH/SELVCH
3V66_3/VCH/SELVCH Output Enable
0 = Disabled,1 = Enabled
DOT_48 Output Enable
0 = Disabled, 1 = Enabled
3
1
Reserved
Reserved
2
1
3V66_2
3V66_2 Output Enable
0 = Disabled, 1 = Enabled
1
1
3V66_1
3V66_1 Output Enable
0 = Disabled, 1 = Enabled
0
1
3V66_0
3V66_0 Output Enable
0 = Disabled, 1 = Enabled
Byte 6: Control Register 6
Bit
@Pup
7
0
Name
Description
REF
PCIF
PCI
3V66
3V66_3/VCH/SELVCH
USB_48
DOT_48
CPUT, CPUT_ITP
CPUC,CPUC_ITP
Test Clock Mode
0 = Disabled, 1 = Enabled
When Test Clock Mode is enabled, the FS_A/REF_0 pin reverts to a
dedicated FS_A input, allowing asynchronous selection between Hi-Z and
REF/N mode.
6
0
Reserved
Reserved, Set = 0
5
0
Reserved
Reserved, Set = 0
4
0
Reserved
Reserved, Set = 0
3
0
Reserved
Reserved, Set = 0
2
0
PCIF
PCI
3V66
CPUT,CPUT_ITP
CPUC,CPUC_ITP
Spread Spectrum Enable
0 = Spread Off, 1 = Spread On
1
1
REF_1
REF_1 Output Enable
0 = Disabled, 1 = Enabled
0
1
REF_0
REF_0 Output Enable
0 = Disabled, 1 = Enabled
Byte 7: Vendor ID
Bit
@Pup
Name
Description
7
0
Revision Code Bit 3
6
1
Revision Code Bit 2
5
0
Revision Code Bit 1
4
0
Revision Code Bit 0
3
1
Vendor ID Bit 3
2
0
Vendor ID Bit 2
1
0
Vendor ID Bit 1
0
0
Vendor ID Bit 0
Document #: 38-07512 Rev. *B
Page 7 of 19
CY28405
Byte 8: Control Register 8
Bit
@Pup
7
0
6
1
5
Name
Description
1
CPU
PCIF
PCI
3V66
Spread Spectrum Selection
‘000’ = ±0.20% triangular
‘001’ = + 0.12, – 0.62%
‘010’ = + 0.25, – 0.75%
‘011’ = –0.05, – 0.45% triangular
‘100’ = ± 0.25%
‘101’ = + 0.00, – 0.50%
‘110’ = ± 0.5%
‘111’ = ± 0.38%
4
0
FSEL_4
SW Frequency selection bits. See Table 1.
3
0
FSEL_3
2
0
FSEL_2
1
0
FSEL_1
0
0
FSEL_0
Byte 9: Control Register 9
Bit
@Pup
Name
Description
7
0
PCIF
PCIF Clock Output Drive Strength Control
0 = Low Drive strength, 1 = High Drive strength
6
0
PCI
PCI Clock Output Drive Strength
0 = Low Drive strength, 1 = High Drive strength
5
0
3V66
3V66 Clock Output Drive Strength
0 = Low Drive strength, 1 = High Drive strength
4
1
REF
REF Clock Output Drive Strength
0 = Low Drive strength, 1 = High Drive strength
3
1
Reserved
Reserved
2
1
Reserved
Reserved
1
0
Reserved
Vendor Test Mode (always program to 0)
0
0
Reserved
Vendor Test Mode (always program to 0)
Byte 10: Control Register 10
Bit
@Pup
7
0
PCI_Skew1
Name
6
0
PCI_Skew0
5
0
3V66_Skew1
4
0
3V66_Skew0
3
1
Reserved
Description
PCI skew control
00 = Normal
01 = –500 ps
10 = Reserved
11 = +500 ps
3V66 skew control
00 = Normal
01 = –150 ps
10 = +150 ps
11 = +300 ps
Reserved, Set = 1
2
1
Reserved
Reserved, Set = 1
1
1
Reserved
Reserved, Set = 1
0
1
Reserved
Reserved, Set = 1
Document #: 38-07512 Rev. *B
Page 8 of 19
CY28405
Byte 11: Control Register 11
Bit
@Pup
Name
Description
7
0
Reserved
Vendor Test Mode (always program to 0)
6
0
Recovery_Frequency
This bit allows selection of the frequency setting that the clock will be
restored to once the system is rebooted
0: Use Hardware settings
1: Use Last SW table Programmed values
5
0
Watchdog Time Stamp
Reload
To enable this function the register bit must first be set to “0” before toggling
to “1”.
0: Do not reload
1: Reset timer but continue to count.
4
0
WD_Alarm
This bit is set to “1” when the Watchdog times out. It is reset to “0” when
the system clears the WD_TIMER time stamp
3
0
WD_TIMER3
2
0
WD_TIMER2
1
0
WD_TIMER1
0
0
WD_TIMER0
Watchdog timer time stamp selection:
0000: Off
0001: 2 second
0010: 4 seconds
0011: 6 seconds
.
.
.
1110: 28seconds
1111: 30seconds
Byte 12: Control Register 12
Bit
@Pup
Name
7
0
CPU_FSEL_N8
6
0
CPU_FSEL_N7
5
0
CPU_FSEL_N6
4
0
CPU_FSEL_N5
3
0
CPU_FSEL_N4
2
0
CPU_FSEL_N3
1
0
CPU_FSEL_N2
0
0
CPU_FSEL_N1
Description
If Prog_Freq_EN is set, the values programmed in CPU_FSEL_N[8:0] and
CPU_FSEL_M[6:0] will be used to determine the CPU output frequency.
The setting of FS_Override bit determines the frequency ratio for CPU and
other output clocks. When it is cleared, the same frequency ratio stated in
the Latched FS[E:A] register will be used. When it is set, the frequency
ratio stated in the SEL[4:0] register will be used.
Byte 13: Control Register 13
Bit
@Pup
7
0
CPU_FSEL_N0
Name
6
0
CPU_FSEL_M6
5
0
CPU_FSEL_M5
4
0
CPU_FSEL_M4
3
0
CPU_FSEL_M3
2
0
CPU_FSEL_M2
1
0
CPU_FSEL_M1
0
0
CPU_FSEL_M0
Description
If Prog_Freq_EN is set, the values programmed in CPU_FSEL_N[8:0] and
CPU_FSEL_M[6:0] will be used to determine the CPU output frequency.
The setting of FS_Override bit determines the frequency ratio for CPU and
other output clocks. When it is cleared, the same frequency ratio stated in
the Latched FS[E:A] register will be used. When it is set, the frequency
ratio stated in the SEL[4:0] register will be used.
Byte 14: Control Register 14
Bit
@Pup
7
0
FS_(E:A)
Name
FS_Override
0 = Select operating frequency by FS(E:A) input pins
1 = Select operating frequency by FSEL(4:0) settings
6
1
Reserved
Reserved, Set = 1
5
0
Reserved
Reserved, Set = 0
Document #: 38-07512 Rev. *B
Description
Page 9 of 19
CY28405
Byte 14: Control Register 14 (continued)
Bit
@Pup
Name
Description
4
0
Reserved
Reserved, Set = 0
3
0
Reserved
Reserved, Set = 0
2
0
Reserved
Reserved, Set = 0
1
0
Reserved
Reserved, Set = 0
0
0
Pro_Freq_EN
Programmable output frequencies enabled
0 = Disabled, 1 = Enabled
Dial-a-Frequency Programming
Crystal Recommendations
When the programmable output frequency feature is enabled
(Pro_Freq_EN bit is set), the CPU output frequency is determined by the following equation:
The CY28405 requires a Parallel Resonance Crystal.
Substituting a series resonance crystal will cause the
CY28405 to operate at the wrong frequency and violate the
ppm specification. For most applications there is a 300-ppm
frequency shift between series and parallel crystals due to
incorrect loading.
Fcpu = G * N/M
“N” and “M” are the values programmed in Programmable
Frequency Select N-Value Register and M-Value Register,
respectively.
“G” stands for the PLL Gear Constant, which is determined by
the programmed value of FS[E:A] or SEL[4:0]. The value is
listed in Table 1.
The ratio of N and M need to be greater than “1” [N/M> 1].
The following table lists set of N and M values for different
frequency output ranges. This example use a fixed value for
the M-Value Register and select the CPU output frequency by
changing the value of the N-Value Register.
Table 5. Examples of N and M Value for Different CPU
Frequency Range
Range of N-Value
Register for
Different CPU
Frequency
Frequency
Ranges
Gear
Constants
Fixed Value
for M-Value
Register
100 –125
24004009.32
48
200 – 250
126 – 166 32005345.76
48
189 – 249
167 – 200 48008018.65
48
167 – 200
Crystal Loading
Crystal loading plays a critical role in achieving low ppm performance. To realize low ppm performance, the total capacitance
the crystal will see must be considered to calculate the appropriate capacitive loading (CL).
Figure 1 shows a typical crystal configuration using the two
trim capacitors. An important clarification for the following
discussion is that the trim capacitors are in series with the
crystal not parallel. It’s a common misconception that load
capacitors are in parallel with the crystal and should be
approximately equal to the load capacitance of the crystal.
This is not true.
Table 6. Crystal Recommendations
Frequency
(Fund)
Cut
Loading Load Cap
Drive
(max.)
Shunt Cap
(max.)
Motional
(max.)
Tolerance
(max.)
Stability
(max.)
Aging
(max.)
14.31818 MHz
AT
Parallel
0.1 mW
5 pF
0.016 pF
50 ppm
50 ppm
5 ppm
Document #: 38-07512 Rev. *B
20 pF
Page 10 of 19
CY28405
As mentioned previously, the capacitance on each side of the
crystal is in series with the crystal. This mean the total capacitance on each side of the crystal must be twice the specified
load capacitance (CL). While the capacitance on each side of
the crystal is in series with the crystal, trim capacitors
(Ce1,Ce2) should be calculated to provide equal capacitative
loading on both sides.
Use the following formulas to calculate the trim capacitor
values for Ce1 and Ce2.
Load Capacitance (each side)
Figure 1. Crystal Capacitive Clarification
Ce = 2 * CL - (Cs + Ci)
Calculating Load Capacitors
Total Capacitance (as seen by the crystal)
In addition to the standard external trim capacitors, trace
capacitance and pin capacitance must also be considered to
correctly calculate crystal loading. As mentioned previously,
the capacitance on each side of the crystal is in series with the
crystal. This means the total capacitance on each side of the
crystal must be twice the specified crystal load capacitance
(CL). While the capacitance on each side of the crystal is in
series with the crystal, trim capacitors (Ce1,Ce2) should be
calculated to provide equal capacitive loading on both sides.
Cs2
Trace
2.8pF
XTAL
Ce1
1
Ce2 + Cs2 + Ci2
)
CL ....................................................Crystal load capacitance
CLe ......................................... Actual loading seen by crystal
...................................... using standard value trim capacitors
Ce ..................................................... External trim capacitors
Cs ............................................. Stray capacitance (trace,etc)
The PD# pin is used to shut off all clocks and PLLs without
having to remove power from the device. All clocks are shut
down in a synchronous manner so has not to cause glitches
while transitioning to the power down state.
PD# – Assertion
X2
X1
1
1
( Ce1 + Cs1
+ Ci1 +
PD# (Power-down) Clarification
Ci2
Pin
3 to 6p
Cs1
=
Ci ............. Internal capacitance (lead frame, bond wires etc)
Clock Chip
Ci1
CLe
Ce2
Trim
33pF
Figure 2. Crystal Loading Example
When PD# is sampled LOW by two consecutive rising edges
of the CPUC clock then all clock outputs (except CPUT) clocks
must be held LOW on their next HIGH to LOW transition. CPU
clocks must be held with CPUT clock pin driven HIGH with a
value of 2x Iref and CPUC undriven as the default condition.
There exists an I2C bit that allows for the CPUT/C outputs to
be three-stated during power-down. Due to the state of internal
logic, stopping and holding the REF clock outputs in the LOW
state may require more than one clock cycle to complete
PWRDWN#
CPUT, 133MHz
CPUC, 133MHz
3V66, 66MHz
USB, 48MHz
PCI, 33MHz
REF, 14.31818
Figure 3. Power-down Assertion Timing Waveforms
Document #: 38-07512 Rev. *B
Page 11 of 19
CY28405
PD# Deassertion
The power-up latency between PD# rising to a valid logic ‘1’
level and the starting of all clocks is less than 1.8 ms. The
CPUT/C outputs must be driven to greater than 200 mV is less
than 300 µs.
Tstable
0.25mS
VTT_PWRGD# = Low
Sample
Inputs straps
VDDA = 2.0V
Wait for 1.146ms
S0
Power Off
S3
VDDA = off
Normal
Operation
Enable Outputs
VTT_PWRGD# = toggle
Figure 6. Clock Generator Power-up/Run State Diagram
Document #: 38-07512 Rev. *B
Page 13 of 19
CY28405
Absolute Maximum Conditions
Parameter
Description
Condition
Min.
Max.
Unit
VDD
Core Supply Voltage
–0.5
4.6
V
VDDA
Analog Supply Voltage
–0.5
4.6
V
VIN
Input Voltage
Relative to V SS
–0.5
VDD + 0.5
VDC
TS
Temperature, Storage
Non-functional
–65
+150
°C
TA
Temperature, Operating Ambient
Functional
0
70
°C
TJ
Temperature, Junction
Functional
–
150
°C
ESDHBM
ESD Protection (Human Body Model)
MIL-STD-883, Method 3015
ØJC
Dissipation, Junction to Case
Mil-Spec 883E Method 1012.1
ØJA
Dissipation, Junction to Ambient
JEDEC (JESD 51)
UL–94
Flammability Rating
At 1/8 in.
MSL
Moisture Sensitivity Level
2000
–
V
15
°C/W
45
°C/W
V–0
1
Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing
is NOT required.
DC Electrical Specifications
Parameter
Description
Conditions
Min.
Max.
Unit
3.135
3.465
V
VDD, VDDA
3.3 Operating Voltage
3.3V ± 5%
VILI2C
Input Low Voltage
SDATA, SCLK
–
–
1.0
VIHI2C
Input High Voltage
SDATA, SCLK
2.2
–
–
VIL
Input Low Voltage
VSS – 0.5
0.8
V
VIH
Input High Voltage
2.0
VDD + 0.5
V
IIL
Input Leakage Current
Except Pull-ups or Pull-downs
0 < VIN < VDD
–5
5
µA
VOL
Output Low Voltage
IOL = 1 mA
–
0.4
V
VOH
Output High Voltage
IOH = –1 mA
IOZ
High-impedance Output Current
CIN
2.4
–
V
–10
10
µA
Input Pin Capacitance
2
5
pF
COUT
Output Pin Capacitance
3
6
pF
LIN
Pin Inductance
–
7
nH
VXIH
Xin High Voltage
0.7VDD
VDD
V
VXIL
Xin Low Voltage
0
0.3VDD
V
IDD
Dynamic Supply Current
At 200 MHz and all outputs
loaded per Table 9 and Figure 7
–
280
mA
IPD
Power-down Supply Current
PD# Asserted
–
1
mA
Document #: 38-07512 Rev. *B
Page 14 of 19
CY28405
AC Electrical Specifications
Parameter
Crystal
TDC
Description
XIN Duty Cycle
Conditions
Min.
Max.
Unit
The device will operate
reliably with input duty cycles
up to 30/70 but the REF clock
duty cycle will not be within
specification
47.5
52.5
%
TPERIOD
XIN period
When Xin is driven from an
external clock source
69.841
71.0
ns
TR / TF
XIN Rise and Fall Times
Measured between 0.3VDD
and 0.7VDD
–
10.0
ns
TCCJ
XIN Cycle to Cycle Jitter
As an average over 1 µs
duration
–
500
ps
LACC
Long-term Accuracy
Over 150ms
300
ppm
CPU at 0.7V
TDC
CPUT and CPUC Duty Cycle
Measured at crossing point VOX
45
55
%
TPERIOD
100-MHz CPUT and CPUC Period
Measured at crossing point VOX
9.9970
10.003
ns
TPERIOD
133-MHz CPUT and CPUC Period
Measured at crossing point VOX
7.4978
7.5023
ns
TPERIOD
200-MHz CPUT and CPUC Period
Measured at crossing point VOX
4.9985
5.0015
ns
TSKEW
Any CPU to CPU Clock Skew
Measured at crossing point VOX
–
100
ps
TCCJ
CPU Cycle to Cycle Jitter
Measured at crossing point VOX
–
125
ps
TR / TF
CPUT and CPUC Rise and Fall Times
Measured from VOL = 0.175
to VOH = 0.525V
175
700
ps
TRFM
Rise/Fall Matching
Determined as a fraction of
2*(TR – TF)/ (TR + TF)
–
20
%
∆TR
Rise Time Variation
–
125
ps
∆TF
Fall Time Variation
–
125
ps
VHIGH
Voltage High
Math average, see Figure 7
660
850
mv
Math average,see Figure 7
–150
–
mv
250
550
mv
VLOW
Voltage Low
VOX
Crossing Point Voltage at 0.7V Swing
VOVS
Maximum Overshoot Voltage
–
VHIGH+0.3
V
VUDS
Minimum Undershoot Voltage
–0.3
–
V
VRB
Ring Back Voltage
See Figure 7. Measure SE
–
0.2
V
3V66
TDC
3V66 Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Spread Disabled 3V66 Period
Measurement at 1.5V
14.9955
15.0045
ns
TPERIOD
Spread Enabled 3V66 Period
Measurement at 1.5V
14.9955
15.0799
ns
THIGH
3V66 High Time
Measurement at 2.4V
4.9500
–
ns
TLOW
3V66 Low Time
Measurement at 0.4V
4.5500
–
ns
TR / TF
3V66 Rise and Fall Times
Measured between 0.4V and
2.4V
0.5
2.0
ns
TSKEW
Any 3V66 to Any 3V66 Clock Skew
Measurement at 1.5V
–
250
ps
TCCJ
3V66 Cycle to Cycle Jitter
Measurement at 1.5V
–
250
ps
PCI/PCIF
TDC
PCIF and PCI Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Spread Disabled PCIF/PCI Period
Measurement at 1.5V
29.9910
30.0009
ns
TPERIOD
Spread Enabled PCIF/PCI Period
Measurement at 1.5V
29.9910
30.1598
ns
THIGH
PCIF and PCI High Time
Measurement at 2.4V
12.0
–
ns
Document #: 38-07512 Rev. *B
Page 15 of 19
CY28405
AC Electrical Specifications (continued)
Min.
Max.
Unit
TLOW
Parameter
PCIF and PCI Low Time
Description
Measurement at 0.4V
Conditions
12.0
–
ns
TR / TF
PCIF and PCI Rise and Fall Times
Measured between 0.4V and
2.4V
0.5
2.0
ns
TSKEW
Any PCI Clock to Any PCI Clock Skew
Measurement at 1.5V
–
500
ps
TCCJ
PCIF and PCI Cycle to Cycle Jitter
Measurement at 1.5V
–
250
ps
DOT
TDC
Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Period
Measurement at 1.5V
20.8257
20.8340
ns
THIGH
DOT High Time
Measurement at 2.4V
8.994
10.486
ns
TLOW
DOT Low Time
Measurement at 0.4V
8.794
10.386
ns
TR / TF
Rise and Fall Times
Measured between 0.4V and
2.4V
0.5
1.0
ns
TCCJ
Cycle to Cycle Jitter
10-µs period
–
350
ps
USB
TDC
Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Period
Measurement at 1.5V
20.8257
20.8340
ns
THIGH
USB High Time
Measurement at 2.4V
8.094
10.036
ns
TLOW
USB Low Time
Measurement at 0.4V
7.694
9.836
ns
TR / TF
Rise and Fall Times
Measured between 0.4V and
2.4V
1.0
2.0
ns
TCCJ
Cycle to Cycle Jitter
125-µs period
–
350
ps
REF
TDC
REF Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
REF Period
Measurement at 1.5V
69.827
69.855
ns
TR / TF
REF Rise and Fall Times
Measured between 0.4V and
2.4V
1.0
4.0
V/ns
TCCJ
REF Cycle to Cycle Jitter
Measurement at 1.5V
–
1000
ps
–
1.5
ms
10.0
–
ns
0
–
ns
ENABLE/DISABLE and SET-UP
TSTABLE
All Clock Stabilization from Power-up
TSS
Stopclock Set-up Time
TSH
Stopclock Hold Time
Table 7. Group Timing Relationship and Tolerances
Offset
Group
Conditions
Min.
Max.
3V66 to PCI
3V66 Leads PCI
1.5 ns
3.5 ns
Table 8. USB to DOT Phase Offset
Parameter
Typical
Value
Tolerance
DOT Skew
0°
0.0 ns
1000 ps
USB Skew
180°
0.0 ns
1000 ps
VCH SKew
0°
0.0 ns
1000 ps
Document #: 38-07512 Rev. *B
Page 16 of 19
CY28405
Test and Measurement Set-up
Table 9. Maximum Lumped Capacitive Output Loads
Clock
Max Load
Units
PCI Clocks
30
pF
3V66 Clocks
30
pF
USB Clock
20
pF
DOT Clock
10
pF
REF Clock
30
pF
CPUT
CPUC
For Differential CPU and SRC Output Signals
The following diagram shows lumped test load configurations
for the differential Host Clock Outputs.
M e a s u re m e n t
P o in t
TPCB
33Ω
4 9 .9 Ω
2pF
M e a s u re m e n t
P o in t
TPCB
33Ω
4 9 .9 Ω
IR E F
2pF
475Ω
Figure 7. 0.7V Load Configuration
O u tp u t u n d e r T e s t
P ro b e
Load Cap
3 .3 V s ig n a l s
tD C
-
-
3 .3 V
2 .4 V
1 .5 V
0 .4 V
0V
Tr
Tf
Figure 8. Lumped Load For Single-Ended Output Signals (for AC Parameter Measurement)
Table 10.CPU Clock Current Select Function
Board Target Trace/Term Z
Reference R, IREF – VDD (3*RREF)
Output Current
VOH @ Z
50 Ohms
RREF = 475 1%, IREF = 2.32 mA
IOH = 6*IREF
0.7V @ 50
Ordering Information
Part Number
Package Type
Product Flow
CY28405OC
48-pin Shrunk Small Outline package (SSOP)
Commercial, 0° to 70°C
CY28405OCT
48-pin Shrunk Small Outline package (SSOP) – Tape and Reel
Commercial, 0° to 70°C
CY28405OXC
48-pin Shrunk Small Outline package (SSOP)
Commercial, 0° to 70°C
CY28405OXCT
48-pin Shrunk Small Outline package (SSOP) – Tape and Reel
Commercial, 0° to 70°C
Lead Free
Document #: 38-07512 Rev. *B
Page 17 of 19
CY28405
Package Drawing and Dimensions
48-Lead Shrunk Small Outline Package O48
51-85061-*C
Purchase of I2C components from Cypress, or one of its sublicensed Associated Companies, conveys a license under the Philips
I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification
as defined by Philips. Intel and Pentium are registered trademarks of Intel Corporation. Dial-a-Frequency is a registered
trademark of Cypress Semiconductor. All product and company names mentioned in this document are trademarks of their
respective holders.
Document #: 38-07512 Rev. *B
Page 18 of 19
© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
CY28405
Document History Page
Document Title: CY28405 CK409-Compliant Clock Synthesizer
Document Number: 38-07512
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
125354
04/15/03
RGL
New Data Sheet
*A
127159
06/16/03
RGL
Removed SRC functionality
Modified the title to CK409-Compliant Clock Synthesizer
*B
235894
See ECN
RGL
Removed all items referencing to 166MHz
Added Lead Free devices in the ordering information table
Document #: 38-07512 Rev. *B
Page 19 of 19
工商网监
湘ICP备2023018690号
