S29GL256N90TFIR23

S29GL512N S29GL256N S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit This product family has been retired and is not recommended for designs. For new and current designs, S29GL128S, S29GL256S, and S29GL512T supersede the S29GL128N, S29GL256N, and S29GL512N respectively. These are the factory-recommended migration paths. Please refer to the S29GL-S and S29GL-T Family data sheets for specifications and ordering information. Distinctive Characteristics  Package Options – 56-pin TSOP – 64-ball Fortified BGA Architectural Advantages  Single Power Supply Operation – 3 volt read, erase, and program operations  Enhanced VersatileI/O Control – All input levels (address, control, and DQ input levels) and outputs are determined by voltage on VIO input. VIO range is 1.65 to VCC Software & Hardware Features ig n  Software Features – Program Suspend and Resume: read other sectors before programming operation is completed – Erase Suspend and Resume: read/program other sectors before an erase operation is completed – Data# polling and toggle bits provide status – Unlock Bypass Program command reduces overall multiple-word programming time – CFI (Common Flash Interface) compliant: allows host system to identify and accommodate multiple flash devices  Manufactured on 110 nm MirrorBit Process Technology  20-year Data Retention typical Performance Characteristics om m en  100,000 Erase Cycles per sector typical D ew rN de d  Compatibility with JEDEC Standards – Provides pinout and software compatibility for single-power supply flash, and superior inadvertent write protection  Hardware Features – Advanced Sector Protection – WP#/ACC input accelerates programming time (when high voltage is applied) for greater throughput during system production. Protects first or last sector regardless of sector protection settings – Hardware reset input (RESET#) resets device – Ready/Busy# output (RY/BY#) detects program or erase cycle completion fo  Flexible Sector Architecture – S29GL512N: Five hundred twelve 64 Kword (128 Kbyte) sectors – S29GL256N: Two hundred fifty-six 64 Kword (128 Kbyte) sectors – S29GL128N: One hundred twenty-eight 64 Kword (128 Kbyte) sectors es  Secured Silicon Sector Region – 128-word/256-byte sector for permanent, secure identification through an 8-word/16-byte random Electronic Serial Number, accessible through a command sequence – May be programmed and locked at the factory or by the customer N ot R ec  High Performance – 90 ns access time (S29GL128N, S29GL256N) – 100 ns (S29GL512N) – 8-word/16-byte page read buffer – 25 ns page read times – 16-word/32-byte write buffer reduces overall programming time for multiple-word updates  Low Power Consumption (typical values at 3.0 V, 5 MHz) – 25 mA typical active read current; – 50 mA typical erase/program current – 1 µA typical standby mode current Cypress Semiconductor Corporation Document Number: 002-01522 Rev. *B • 198 Champion Court Product Availability Table Density 512 Mb 256 Mb 128 Mb • Init. Access VCC Availability 110 ns Full Now 100 ns Full Now 110 ns Full Now 100 ns Full Now 90 ns Regulated Now 110 ns Full Now 100 ns Full Now 90 ns Regulated Now San Jose, CA 95134-1709 • 408-943-2600 Revised January 08, 2016 S29GL512N S29GL256N S29GL128N General Description The S29GL512/256/128N family of devices are 3.0V single power flash memory manufactured using 110 nmMirrorBit technology. The S29GL512N is a 512 Mbit, organized as 33,554,432 words or 67,108,864 bytes. The S29GL256N is a 256 Mbit, organized as 16,777,216 words or 33,554,432 bytes. The S29GL128N is a 128 Mbit, organized as 8,388,608 words or 16,777,216 bytes. The devices have a 16-bit wide data bus that can also function as an 8-bit wide data bus by using the BYTE# input. The device can be programmed either in the host system or in standard EPROM programmers. Access times as fast as 90 ns (S29GL128N, S29GL256N), 100 ns (S29GL512N) are available. Note that each access time has a specific operating voltage range (VCC) and an I/O voltage range (VIO), as specified in the Product Selector Guide on page 4 and the Ordering Information on page 9. The devices are offered in a 56-pin TSOP or 64-ball Fortified BGA package. Each device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. ig n Each device requires only a single 3.0 volt power supply for both read and write functions. In addition to a VCC input, a highvoltage accelerated program (WP#/ACC) input provides shorter programming times through increased current. This feature is intended to facilitate factory throughput during system production, but may also be used in the field if desired. D es The devices are entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the device using standard microprocessor write timing. Write cycles also internally latch addresses and data needed for the programming and erase operations. ew The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. d fo rN Device programming and erasure are initiated through command sequences. Once a program or erase operation has begun, the host system need only poll the DQ7 (Data# Polling) or DQ6 (toggle) status bits or monitor the Ready/Busy# (RY/BY#) output to determine whether the operation is complete. To facilitate programming, an Unlock Bypass mode reduces command sequence overhead by requiring only two write cycles to program data instead of four. om m en de The Enhanced VersatileI/O™ (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on all input levels (address, chip control, and DQ input levels) to the same voltage level that is asserted on the VIO pin. This allows the device to operate in a 1.8 V or 3 V system environment as required. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. Persistent Sector Protection provides in-system, command-enabled protection of any combination of sectors using a single power supply at VCC. Password Sector Protection prevents unauthorized write and erase operations in any combination of sectors through a user-defined 64-bit password. R ec The Erase Suspend/Erase Resume feature allows the host system to pause an erase operation in a given sector to read or program any other sector and then complete the erase operation. The Program Suspend/Program Resume feature enables the host system to pause a program operation in a given sector to read any other sector and then complete the program operation. N ot The hardware RESET# pin terminates any operation in progress and resets the device, after which it is then ready for a new operation. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the device, enabling the host system to read boot-up firmware from the Flash memory device. The device reduces power consumption in the standby mode when it detects specific voltage levels on CE# and RESET#, or when addresses have been stable for a specified period of time. The Secured Silicon Sector provides a 128-word/256-byte area for code or data that can be permanently protected. Once this sector is protected, no further changes within the sector can occur. The Write Protect (WP#/ACC) feature protects the first or last sector by asserting a logic low on the WP# pin. MirrorBit flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via hot-hole assisted erase. The data is programmed using hot electron injection. Document Number: 002-01522 Rev. *B Page 2 of 92 S29GL512N S29GL256N S29GL128N Contents Product Selector Guide ............................................... 4 S29GL512N ................................................................... 4 S29GL256N, S29GL128N ............................................. 4 9.15 Secured Silicon Sector Entry Command....................... 54 9.16 Secured Silicon Sector Exit Command ......................... 54 9.17 Command Definitions.................................................... 54 2. Block Diagram.............................................................. 5 3. 3.1 Connection Diagrams.................................................. 6 Special Package Handling Instructions.......................... 7 4. Pin Description............................................................. 7 5. Logic Symbol ............................................................... 7 6. Ordering Information ................................................... 9 7. 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 7.21 Device Bus Operations.............................................. Word/Byte Configuration.............................................. VersatileIOTM (VIO) Control .......................................... Requirements for Reading Array Data......................... Writing Commands/Command Sequences.................. Standby Mode.............................................................. Automatic Sleep Mode................................................. RESET#: Hardware Reset Pin..................................... Output Disable Mode ................................................... Autoselect Mode .......................................................... Sector Protection ......................................................... Advanced Sector Protection ........................................ Lock Register ............................................................... Persistent Sector Protection ........................................ Persistent Protection Mode Lock Bit ............................ Password Sector Protection......................................... Password and Password Protection Mode Lock Bit .... 64-bit Password ........................................................... Persistent Protection Bit Lock (PPB Lock Bit).............. Secured Silicon Sector Flash Memory Region ............ Write Protect (WP#) ..................................................... Hardware Data Protection............................................ 10. 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 Write Operation Status ............................................... 59 DQ7: Data# Polling ....................................................... 59 RY/BY#: Ready/Busy#.................................................. 60 DQ6: Toggle Bit I .......................................................... 60 DQ2: Toggle Bit II ......................................................... 62 Reading Toggle Bits DQ6/DQ2..................................... 62 DQ5: Exceeded Timing Limits ...................................... 62 DQ3: Sector Erase Timer.............................................. 63 DQ1: Write-to-Buffer Abort............................................ 63 11. Absolute Maximum Ratings....................................... 64 12. Operating Ranges ....................................................... 65 8. Common Flash Memory Interface (CFI) ................... 40 9. 9.1 9.2 9.3 9.4 Command Definitions................................................ Reading Array Data ..................................................... Reset Command .......................................................... Autoselect Command Sequence ................................. Enter Secured Silicon Sector/Exit Secured Silicon Sector Command Sequence........................................ Word Program Command Sequence........................... Program Suspend/Program Resume Command Sequence..................................................................... Chip Erase Command Sequence ................................ Sector Erase Command Sequence ............................. Erase Suspend/Erase Resume Commands ................ Lock Register Command Set Definitions ..................... Password Protection Command Set Definitions .......... Non-Volatile Sector Protection Command Set Definitions .................................................................... Global Volatile Sector Protection Freeze Command Set............................................................................... Volatile Sector Protection Command Set..................... 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 9.14 rN 14. Test Conditions ........................................................... 66 14.1 Key to Switching Waveforms ........................................ 67 15. 15.1 15.2 15.3 15.4 AC Characteristics...................................................... 68 Read-Only Operations .................................................. 68 Hardware Reset (RESET#)........................................... 69 Erase and Program Operations .................................... 71 Alternate CE# Controlled Erase and Program Operations: S29GL128N, S29GL256N, S29GL512N....................... 75 16. Erase And Programming Performance..................... 77 17. TSOP Pin and BGA Package Capacitance................ 77 fo de om m en ec R ot N Document Number: 002-01522 Rev. *B 43 43 43 44 es ew D 13. DC Characteristics...................................................... 65 13.1 CMOS Compatible ........................................................ 65 d 10 10 10 10 11 11 12 12 13 34 34 35 35 36 37 38 38 38 38 39 40 40 ig n 1. 1.1 1.2 18. Physical Dimensions .................................................. 78 18.1 TS056—56-Pin Standard Thin Small Outline Package (TSOP).......................................................................... 78 18.2 LAA064—64-Ball Fortified Ball Grid Array (FBGA)....... 79 19. Advance Information on S29GL-P Hardware Reset (RESET#) and Power-up Sequence ................................... 80 20. Advance Information on S29GL-R 65 nm MirrorBit ..... Hardware Reset (RESET#) and Power-up Sequence ....... 82 21. Document History Page ............................................. 84 44 44 48 49 50 51 51 52 52 53 53 Page 3 of 92 S29GL512N S29GL256N S29GL128N 1. 1.1 Product Selector Guide S29GL512N Part Number S29GL512N VIO = 2.7–3.6 V 10 11 Max. Access Time (ns) 100 110 110 Max. CE# Access Time (ns) 100 110 110 Max. Page access time (ns) 25 25 30 Max. OE# Access Time (ns) 25 35 35 VCC = 2.7–3.6 V VIO = 1.65–3.6 V 11 S29GL256N, S29GL128N D 1.2 es ig n Speed Option VIO = 2.7–3.6 V VCC = 2.7–3.6 V VIO = 1.65–3.6 V VCC = Regulated (3.0–3.6 V) rN Speed Option S29GL256N, S29GL128N ew Part Number VIO = Regulated (3.0–3.6 V) fo Max. Access Time (ns) d Max. CE# Access Time (ns) de Max. Page access time (ns) 11 11 90 90 100 110 110 90 100 110 110 25 25 25 30 25 25 35 35 N ot R ec om m en Max. OE# Access Time (ns) 10 Document Number: 002-01522 Rev. *B Page 4 of 92 S29GL512N S29GL256N S29GL128N 2. Block Diagram DQ15–DQ0 (A-1) RY/BY# VCC Sector Switches VSS VIO Erase Voltage Generator RESET# WE# WP#/ACC Input/Output Buffers State Control Command Register ig n BYTE# Data Latch Y-Decoder Y-Gating X-Decoder Cell Matrix R ec AMax**–A0 Address Latch om m en Timer de VCC Detector d fo STB rN ew OE# STB D Chip Enable Output Enable Logic CE# es PGM Voltage Generator N ot Note ** AMax GL512N = A24, AMax GL256N = A23, AMax GL128N = A22 Document Number: 002-01522 Rev. *B Page 5 of 92 S29GL512N S29GL256N S29GL128N 3. Connection Diagrams Figure 3.1 56-Pin Standard TSOP 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 A24 NC A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 NC VIO NC for S29GL256N and S29GL128N rN ew D es ig n 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 fo A23 A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 NC NC d NC for S29GL128N de Figure 3.2 64-ball Fortified BGA A8 B8 C8 D8 E8 F8 G8 H8 A22 A231 VIO VSS A242 NC NC ec NC om m en Top View, Balls Facing Down R A7 N ot A13 B7 C7 D7 E7 F7 G7 H7 A12 A14 A15 A16 BYTE# DQ15/A-1 VSS A6 B6 C6 D6 E6 F6 G6 H6 A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 A5 B5 C5 D5 E5 F5 G5 H5 WE# RESET# A21 A19 DQ5 DQ12 VCC DQ4 A4 B4 RY/BY# WP#/ACC C4 D4 E4 F4 G4 H4 A18 A20 DQ2 DQ10 DQ11 DQ3 A3 B3 C3 D3 E3 F3 G3 H3 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1 A2 B2 C2 D2 E2 F2 G2 H2 A3 A4 A2 A1 A0 CE# OE# VSS A1 B1 C1 D1 E1 F1 G1 H1 NC NC NC NC NC VIO NC NC Notes 1. Ball C8 is NC on S29GL128N 2. Ball F8 is NC on S29GL256N and S29GL128N Document Number: 002-01522 Rev. *B Page 6 of 92 S29GL512N S29GL256N S29GL128N 3.1 Special Package Handling Instructions Special handling is required for Flash Memory products in molded packages (TSOP, BGA). The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150C for prolonged periods of time. 4. Pin Description A24–A0 25 Address inputs (512 Mb) A23–A0 24 Address inputs (256 Mb) A22–A0 23 Address inputs (128 Mb) Output Enable input WE# Write Enable input WP#/ACC RESET# es Chip Enable input OE# ig n DQ15 (Data input/output, word mode), A-1 (LSB Address input, byte mode) CE# Hardware Write Protect input; Acceleration input D DQ15/A-1 15 Data inputs/outputs Hardware Reset Pin input BYTE# Selects 8-bit or 16-bit mode RY/BY# Ready/Busy output ew DQ14–DQ0 3.0 volt-only single power supply (see Product Selector Guide on page 4 for speed options and voltage supply tolerances) rN VCC Output Buffer power Device Ground NC Pin Not Connected Internally 5. Logic Symbol om m en de d fo VIO VSS Figure 5.1 S29GL512N N ot R ec 25 A24–A0 CE# 16 or 8 DQ15–DQ0 (A-1) OE# WE# WP#/ACC RESET# VIO RY/BY# BYTE# Document Number: 002-01522 Rev. *B Page 7 of 92 S29GL512N S29GL256N S29GL128N Figure 5.2 S29GL256N 24 A23–A0 16 or 8 DQ15–DQ0 (A-1) CE# OE# WE# WP#/ACC RESET# VIO ig n RY/BY# ew D es BYTE# rN Figure 5.3 S29GL128N 23 fo A22–A0 DQ15–DQ0 (A-1) om m en de d CE# OE# 16 or 8 WE# WP#/ACC VIO RY/BY# BYTE# N ot R ec RESET# This product family has been retired and is not recommended for designs. For new and current designs, S29GL128P, S29GL256P, and S29GL512P supersede S29GL128N, S29GL256N, and S29GL512N respectively. These are the factory-recommended migration paths. Please refer to the S29GL-P Family data sheets for specifications and ordering information. Document Number: 002-01522 Rev. *B Page 8 of 92 S29GL512N S29GL256N S29GL128N 6. Ordering Information The ordering part number is formed by a valid combination of the following: S29GL512N 11 F F I 01 0 PACKING TYPE 0 = Tray (standard; see note 1) 2 = 7” Tape and Reel 3 = 13” Tape and Reel ig n MODEL NUMBER (VIO range, protection when WP# =VIL) 01 = VIO = VCC = 2.7 to 3.6 V, highest address sector protected 02 = VIO = VCC = 2.7 to 3.6 V, lowest address sector protected V1 = VIO = 1.65 to 3.6 V, VCC = 2.7 to 3.6 V, highest address sector protected V2 = VIO = 1.65 to 3.6 V, VCC = 2.7 to 3.6 V, lowest address sector protected R1 = VIO = VCC = 3.0 to 3.6 V, highest address sector protected R2 = VIO = VCC = 3.0 to 3.6 V, lowest address sector protected es TEMPERATURE RANGE I = Industrial (–40°C to +85°C) D PACKAGE MATERIALS SET A = SnPb F = Pb-free (Recommended) rN ew PACKAGE TYPE T = Thin Small Outline Package (TSOP) Standard Pinout (TS056) F = Fortified Ball Grid Array, 1.0 mm pitch package (LAA064) d fo SPEED OPTION 90 = 90 ns (Note 4) 10 = 100 ns (Note 4) 11 = 110 ns (Recommended) om m en de DEVICE NUMBER/DESCRIPTION S29GL128N, S29GL256N, S29GL512N 3.0 Volt-only, 512 Megabit (32 M x 16-Bit/64 M x 8-Bit) Page-Mode Flash Memory Manufactured on 110 nm MirrorBit process technology Valid Combinations 90 S29GL128N ot Speed (ns) N Base Part Number R ec Valid Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to confirm availability of specific valid combinations and to check on newly released combinations. 10, 11 S29GL-N Valid Combinations Package Temperature TA, TF (Note 2); FA, FF (Note 3) Model Number I 11 10, 11 S29GL512N 11 0, 2, 3 (Note 1) R1, R2 TA, TF (Note 2); FA, FF (Note 3) I 11 10, 11 01, 02 V1, V2 90 S29GL256N Packing Type R1, R2 01, 02 0, 2, 3 (Note 1) V1, V2 TA, TF (Note 2); FA, FF (Note 3) I 01, 02 V1, V2 0, 2, 3 (Note 1) Notes 1. Type 0 is standard. Specify other options as required. TSOP can be packed in Types 0 and 3; BGA can be packed in Types 0, 2, 3. 2. TSOP package marking omits packing type designator from ordering part number. 3. BGA package marking omits leading “S29” and packing type designator from ordering part number. 4. Contact a local sales representative for availability. Document Number: 002-01522 Rev. *B Page 9 of 92 S29GL512N S29GL256N S29GL128N 7. Device Bus Operations This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The contents of the register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. Device Bus Operations DQ8–DQ15 CE# Read Write (Program/Erase) L WE# L L H L H L H L WP#/ACC H X AIN DOUT DOUT H (Note 2) AIN (Note 3) (Note 3) H VHH AIN (Note 3) (Note 3) H X High-Z RESET# BYTE# = VIH BYTE# = VIL DQ8–DQ14 = High-Z, DQ15 = A-1 VCC ± 0.3 V X X VCC ± 0.3 V es Accelerated Program OE# DQ0– DQ7 ig n Operation Addresses (Note 1) High-Z Output Disable L H H H X X High-Z High-Z High-Z Reset X X X L X X High-Z High-Z High-Z High-Z D ew Standby rN Legend L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5V, X = Don’t Care, SA = Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out fo Notes 1. Addresses are AMax:A0 in word mode; AMax:A-1 in byte mode. Sector addresses are AMax:A16 in both modes. de d 2. If WP# = VIL, the first or last sector group remains protected. If WP# = VIH, the first or last sector is protected or unprotected as determined by the method described in “Write Protect (WP#)”. All sectors are unprotected when shipped from the factory (The Secured Silicon Sector may be factory protected depending on version ordered.) 7.1 om m en 3. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 9.2 on page 48, Figure 9.4 on page 50, and Figure 10.1 on page 60). Word/Byte Configuration ec The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0–DQ15 are active and controlled by CE# and OE#. 7.2 N ot R If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ0–DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8–DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. VersatileIOTM (VIO) Control The VersatileIOTM (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on CE# and DQ I/Os to the same voltage level that is asserted on VIO. See Ordering Information for VIO options on this device. For example, a VI/O of 1.65–3.6 volts allows for I/O at the 1.8 or 3 volt levels, driving and receiving signals to and from other 1.8 or 3 V devices on the same data bus. 7.3 Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. Document Number: 002-01522 Rev. *B Page 10 of 92 S29GL512N S29GL256N S29GL128N See Reading Array Data on page 43 for more information. Refer to the AC Read-Only Operations table for timing specifications and to Figure 15.1 on page 68 for the timing diagram. Refer to the DC Characteristics table for the active current specification on reading array data. 7.3.1 Page Mode Read The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. The page size of the device is 8 words/16 bytes. The appropriate page is selected by the higher address bits A(max)–A3. Address bits A2–A0 in word mode (A2–A-1 in byte mode) determine the specific word within a page. This is an asynchronous operation; the microprocessor supplies the specific word location. Writing Commands/Command Sequences es 7.4 ig n The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is de-asserted and reasserted for a subsequent access, the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the “read-page addresses” constant and changing the “intra-read page” addresses. ew D To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. rN The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The “Word Program Command Sequence” section has details on programming data to the device using both standard and Unlock Bypass command sequences. fo An erase operation can erase one sector, multiple sectors, or the entire device. Table on page 13, Table on page 31, and Table on page 34 indicate the address space that each sector occupies. 7.4.1 om m en de d Refer to the DC Characteristics table for the active current specification for the write mode. The AC Characteristics section contains timing specification tables and timing diagrams for write operations. Write Buffer 7.4.2 ec Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. See Write Buffer on page 11 for more information. Accelerated Program Operation ot R The device offers accelerated program operations through the ACC function. This is one of two functions provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput at the factory. N If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sector groups, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. WP# has an internal pull-up; when unconnected, WP# is at VIH. 7.4.3 Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. Refer to the Autoselect Mode on page 34 and Autoselect Command Sequence on page 44, for more information. 7.5 Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VIO ± 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VIO ± 0.3 V, the device is in the standby mode, Document Number: 002-01522 Rev. *B Page 11 of 92 S29GL512N S29GL256N S29GL128N but the standby current is greater. The device requires standard access time (tCE) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. Refer to DC Characteristics on page 65 for the standby current specification. 7.6 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. Refer to DC Characteristics on page 65 for the automatic sleep mode current specification. RESET#: Hardware Reset Pin ig n 7.7 ew D es The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/ write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. rN Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the device draws CMOS standby current (ICC5). If RESET# is held at VIL but not within VSS±0.3 V, the standby current is greater. fo The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. N ot R ec om m en de d Refer to the AC Characteristics tables for RESET# parameters and to Figure 15.3 on page 70 for the timing diagram. Document Number: 002-01522 Rev. *B Page 12 of 92 S29GL512N S29GL256N S29GL128N 7.8 Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state. Sector Address Table–S29GL512N (Sheet 1 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0 0 0 0 0 0 0 0 0 128/64 0000000–001FFFF 0000000–000FFFF SA1 0 0 0 0 0 0 0 0 1 128/64 0020000–003FFFF 0010000–001FFFF SA2 0 0 0 0 0 0 0 1 0 128/64 0040000–005FFFF 0020000–002FFFF SA3 0 0 0 0 0 0 0 1 1 128/64 0060000–007FFFF 0030000–003FFFF SA4 0 0 0 0 0 0 1 0 0 128/64 0080000–009FFFF 0040000–004FFFF SA5 0 0 0 0 0 0 1 0 1 128/64 00A0000–00BFFFF 0050000–005FFFF SA6 0 0 0 0 0 0 1 1 0 128/64 00C0000–00DFFFF SA7 0 0 0 0 0 0 1 1 1 128/64 00E0000–00FFFFF SA8 0 0 0 0 0 1 0 0 0 128/64 0100000–011FFFF SA9 0 0 0 0 0 1 0 0 1 128/64 0120000–013FFFF ig n SA0 0060000–006FFFF es 0070000–007FFFF D 0080000–008FFFF 0 0 0 0 1 0 1 0 128/64 0140000–015FFFF 00A0000–00AFFFF 0 0 0 0 0 1 0 1 1 128/64 0160000–017FFFF 00B0000–00BFFFF SA12 0 0 0 0 0 1 1 0 0 128/64 SA13 0 0 0 0 0 1 1 0 1 128/64 SA14 0 0 0 0 0 1 1 1 0 128/64 SA15 0 0 0 0 0 1 1 1 1 128/64 SA16 0 0 0 0 1 0 0 0 0 128/64 0200000–021FFFF SA17 0 0 0 0 1 0 0 0 1 128/64 0220000–023FFFF 0110000–011FFFF SA18 0 0 0 0 1 0 0 1 0 128/64 0240000–025FFFF 0120000–012FFFF SA19 0 0 0 0 1 0 0 1 1 128/64 0260000–027FFFF 0130000–013FFFF SA20 0 0 0 0 1 0 1 0 0 128/64 0280000–029FFFF 0140000–014FFFF SA21 0 0 0 0 1 0 1 0 1 128/64 02A0000–02BFFFF 0150000–015FFFF SA22 0 0 0 0 1 0 1 1 0 128/64 02C0000–02DFFFF 0160000–016FFFF SA23 0 0 0 0 1 0 1 1 1 128/64 02E0000–02FFFFF 0170000–017FFFF SA24 0 0 0 0 1 1 0 0 0 128/64 0300000–031FFFF 0180000–018FFFF SA25 0 0 0 0 1 1 0 0 1 128/64 0320000–033FFFF 0190000–019FFFF SA26 0 0 0 0 1 0 1 0 128/64 0340000–035FFFF 01A0000–01AFFFF SA27 0 0 0 0360000–037FFFF 01B0000–01BFFFF SA28 0 0 SA29 0 0 SA30 0 SA31 0 SA32 SA33 R ot N 1 ew 0 SA11 ec SA10 om m en 0090000–009FFFF 00C0000–00CFFFF 00D0000–00DFFFF 01C0000–01DFFFF 00E0000–00EFFFF 01E0000–01FFFFF 00F0000–00FFFFF de d fo rN 0180000–019FFFF 01A0000–01BFFFF 0100000–010FFFF 0 1 1 0 1 1 128/64 0 0 1 1 1 0 0 128/64 0380000–039FFFF 01C0000–01CFFFF 0 0 1 1 1 0 1 128/64 03A0000–03BFFFF 01D0000–01DFFFF 0 0 0 1 1 1 1 0 128/64 03C0000–03DFFFF 01E0000–01EFFFF 0 0 0 1 1 1 1 1 128/64 03E0000–0EFFFFF 01F0000–01FFFFF 0 0 0 1 0 0 0 0 0 128/64 0400000–041FFFF 0200000–020FFFF 0 0 0 1 0 0 0 0 1 128/64 0420000–043FFFF 0210000–021FFFF SA34 0 0 0 1 0 0 0 1 0 128/64 0440000–045FFFF 0220000–022FFFF SA35 0 0 0 1 0 0 0 1 1 128/64 0460000–047FFFF 0230000–023FFFF SA36 0 0 0 1 0 0 1 0 0 128/64 0480000–049FFFF 0240000–024FFFF SA37 0 0 0 1 0 0 1 0 1 128/64 04A0000–04BFFFF 0250000–025FFFF SA38 0 0 0 1 0 0 1 1 0 128/64 04C0000–04DFFFF 0260000–026FFFF SA39 0 0 0 1 0 0 1 1 1 128/64 04E0000–04FFFFF 0270000–027FFFF SA40 0 0 0 1 0 1 0 0 0 128/64 0500000–051FFFF 0280000–028FFFF SA41 0 0 0 1 0 1 0 0 1 128/64 0520000–053FFFF 0290000–029FFFF Document Number: 002-01522 Rev. *B Page 13 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 2 of 12) Sector SA42 A24–A16 0 0 0 1 0 1 0 1 0 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 128/64 0540000–055FFFF 02A0000–02AFFFF 0 0 0 1 0 1 0 1 1 128/64 0560000–057FFFF 02B0000–02BFFFF SA44 0 0 0 1 0 1 1 0 0 128/64 0580000–059FFFF 02C0000–02CFFFF SA45 0 0 0 1 0 1 1 0 1 128/64 05A0000–05BFFFF 02D0000–02DFFFF SA46 0 0 0 1 0 1 1 1 0 128/64 05C0000–05DFFFF 02E0000–02EFFFF SA47 0 0 0 1 0 1 1 1 1 128/64 05E0000–05FFFFF 02F0000–02FFFFF SA48 0 0 0 1 1 0 0 0 0 128/64 0600000–061FFFF 0300000–030FFFF SA49 0 0 0 1 1 0 0 0 1 128/64 0620000–063FFFF 0310000–031FFFF SA50 0 0 0 1 1 0 0 1 0 128/64 0640000–065FFFF 0320000–032FFFF SA51 0 0 0 1 1 0 0 1 1 128/64 0660000–067FFFF SA52 0 0 0 1 1 0 1 0 0 128/64 0680000–069FFFF SA53 0 0 0 1 1 0 1 0 1 128/64 06A0000–06BFFFF SA54 0 0 0 1 1 0 1 1 0 128/64 06C0000–06DFFFF SA55 0 0 0 1 1 0 1 1 1 128/64 06E0000–06FFFFF 0370000–037FFFF SA56 0 0 0 1 1 1 0 0 0 128/64 0700000–071FFFF 0380000–038FFFF SA57 0 0 0 1 1 1 0 0 1 128/64 0720000–073FFFF 0390000–039FFFF SA58 0 0 0 1 1 1 0 1 0 128/64 0740000–075FFFF 03A0000–03AFFFF 1 1 0 1 1 128/64 1 1 1 1 0 0 128/64 SA61 0 0 0 1 1 1 1 0 1 SA62 0 0 0 1 1 1 1 1 0 SA63 0 0 0 1 1 1 1 1 1 SA64 0 0 1 0 0 0 0 0 0 SA65 0 0 1 0 0 0 0 0 SA66 0 0 1 0 0 0 0 SA67 0 0 1 0 0 0 SA68 0 0 1 0 0 0 SA69 0 0 1 0 0 SA70 0 0 1 0 SA71 0 0 1 0 SA72 0 0 1 SA73 0 0 SA74 0 0 es 0350000–035FFFF D ew rN fo 1 0 0360000–036FFFF 0760000–077FFFF 03B0000–03BFFFF 0780000–079FFFF 03C0000–03CFFFF 128/64 07A0000–07BFFFF 03D0000–03DFFFF 128/64 07C0000–07DFFFF 03E0000–03EFFFF 128/64 07E0000–07FFFFF 03F0000–03FFFFF 128/64 0800000–081FFFF 0400000–040FFFF 1 128/64 0820000–083FFFF 0410000–041FFFF 1 0 128/64 0840000–085FFFF 0420000–042FFFF 0 1 1 128/64 0860000–087FFFF 0430000–043FFFF 1 0 0 128/64 0880000–089FFFF 0440000–044FFFF de d 0 0 0340000–034FFFF om m en 0 0 ec 0 SA60 0330000–033FFFF R SA59 ig n SA43 1 0 1 128/64 08A0000–08BFFFF 0450000–045FFFF 0 0 1 1 0 128/64 08C0000–08DFFFF 0460000–046FFFF ot 0 0 1 1 1 128/64 08E0000–08FFFFF 0470000–047FFFF 0 1 0 0 0 128/64 0900000–091FFFF 0480000–048FFFF 1 0 0 1 0 0 1 128/64 0920000–093FFFF 0490000–049FFFF 1 0 0 1 0 1 0 128/64 0940000–095FFFF 04A0000–04AFFFF N 0 0 SA75 0 0 1 0 0 1 0 1 1 128/64 0960000–097FFFF 04B0000–04BFFFF SA76 0 0 1 0 0 1 1 0 0 128/64 0980000–099FFFF 04C0000–04CFFFF SA77 0 0 1 0 0 1 1 0 1 128/64 09A0000–09BFFFF 04D0000–04DFFFF SA78 0 0 1 0 0 1 1 1 0 128/64 09C0000–09DFFFF 04E0000–04EFFFF SA79 0 0 1 0 0 1 1 1 1 128/64 09E0000–09FFFFF 04F0000–04FFFFF SA80 0 0 1 0 1 0 0 0 0 128/64 0A00000–0A1FFFF 0500000–050FFFF SA81 0 0 1 0 1 0 0 0 1 128/64 0A20000–0A3FFFF 0510000–051FFFF SA82 0 0 1 0 1 0 0 1 0 128/64 0A40000–0A5FFFF 0520000–052FFFF SA83 0 0 1 0 1 0 0 1 1 128/64 0A60000–0A7FFFF 0530000–053FFFF SA84 0 0 1 0 1 0 1 0 0 128/64 0A80000–0A9FFFF 0540000–054FFFF SA85 0 0 1 0 1 0 1 0 1 128/64 0AA0000–0ABFFFF 0550000–055FFFF SA86 0 0 1 0 1 0 1 1 0 128/64 0AC0000–0ADFFFF 0560000–056FFFF Document Number: 002-01522 Rev. *B Page 14 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 3 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0 0 1 0 1 0 1 1 1 128/64 0AE0000–0AFFFFF 0570000–057FFFF SA88 0 0 1 0 1 1 0 0 0 128/64 0B00000–0B1FFFF 0580000–058FFFF SA89 0 0 1 0 1 1 0 0 1 128/64 0B20000–0B3FFFF 0590000–059FFFF SA90 0 0 1 0 1 1 0 1 0 128/64 0B40000–0B5FFFF 05A0000–05AFFFF SA91 0 0 1 0 1 1 0 1 1 128/64 0B60000–0B7FFFF 05B0000–05BFFFF SA92 0 0 1 0 1 1 1 0 0 128/64 0B80000–0B9FFFF 05C0000–05CFFFF SA93 0 0 1 0 1 1 1 0 1 128/64 0BA0000–0BBFFFF 05D0000–05DFFFF SA94 0 0 1 0 1 1 1 1 0 128/64 0BC0000–0BDFFFF 05E0000–05EFFFF SA95 0 0 1 0 1 1 1 1 1 128/64 0BE0000–0BFFFFF 05F0000–05FFFFF SA96 0 0 1 1 0 0 0 0 0 128/64 0C00000–0C1FFFF SA97 0 0 1 1 0 0 0 0 1 128/64 0C20000–0C3FFFF SA98 0 0 1 1 0 0 0 1 0 128/64 0C40000–0C5FFFF SA99 0 0 1 1 0 0 0 1 1 128/64 0C60000–0C7FFFF 0630000–063FFFF SA100 0 0 1 1 0 0 1 0 0 128/64 0C80000–0C9FFFF 0640000–064FFFF SA101 0 0 1 1 0 0 1 0 1 128/64 0CA0000–0CBFFFF 0650000–065FFFF SA102 0 0 1 1 0 0 1 1 0 128/64 0CC0000–0CDFFFF 0660000–066FFFF SA103 0 0 1 1 0 0 1 1 1 128/64 0CE0000–0CFFFFF 0670000–067FFFF SA104 0 0 1 1 0 1 0 0 0 128/64 SA105 0 0 1 1 0 1 0 0 1 128/64 SA106 0 0 1 1 0 1 0 1 0 SA107 0 0 1 1 0 1 0 1 1 SA108 0 0 1 1 0 1 1 0 0 SA109 0 0 1 1 0 1 1 0 1 SA110 0 0 1 1 0 1 1 1 SA111 0 0 1 1 0 1 1 SA112 0 0 1 1 1 0 SA113 0 0 1 1 1 0 SA114 0 0 1 1 1 SA115 0 0 1 1 SA116 0 0 1 1 SA117 0 0 1 SA118 0 0 SA119 0 0 SA120 0 SA121 0 SA122 ig n SA87 0600000–060FFFF es 0610000–061FFFF fo rN ew D 0620000–062FFFF 0680000–068FFFF 0690000–069FFFF 128/64 0D40000–0D5FFFF 06A0000–06AFFFF 128/64 0D60000–0D7FFFF 06B0000–06BFFFF 128/64 0D80000–0D9FFFF 06C0000–06CFFFF 128/64 0DA0000–0DBFFFF 06D0000–06DFFFF 0 128/64 0DC0000–0DDFFFF 06E0000–06EFFFF 1 1 128/64 0DE0000–0DFFFFF 06F0000–06FFFFF 0 0 0 128/64 0E00000–0E1FFFF 0700000–070FFFF 0 0 1 128/64 0E20000–0E3FFFF 0710000–071FFFF ec om m en de d 0D20000–0D3FFFF R 0D00000–0D1FFFF 0 1 0 128/64 0E40000–0E5FFFF 0720000–072FFFF 1 0 0 1 1 128/64 0E60000–0E7FFFF 0730000–073FFFF ot 0 0 1 0 0 128/64 0E80000–0E9FFFF 0740000–074FFFF 1 0 1 0 1 128/64 0EA0000–0EBFFFF 0750000–075FFFF 1 1 1 0 1 1 0 128/64 0EC0000–0EDFFFF 0760000–076FFFF 1 1 1 0 1 1 1 128/64 0EE0000–0EFFFFF 0770000–077FFFF 0 1 1 1 1 0 0 0 128/64 0F00000–0F1FFFF 0780000–078FFFF 0 1 1 1 1 0 0 1 128/64 0F20000–0F3FFFF 0790000–079FFFF 0 0 1 1 1 1 0 1 0 128/64 0F40000–0F5FFFF 07A0000–07AFFFF SA123 0 0 1 1 1 1 0 1 1 128/64 0F60000–0F7FFFF 07B0000–07BFFFF SA124 0 0 1 1 1 1 1 0 0 128/64 0F80000–0F9FFFF 07C0000–07CFFFF SA125 0 0 1 1 1 1 1 0 1 128/64 0FA0000–0FBFFFF 07D0000–07DFFFF SA126 0 0 1 1 1 1 1 1 0 128/64 0FC0000–0FDFFFF 07E0000–07EFFFF SA127 0 0 1 1 1 1 1 1 1 128/64 0FE0000–0FFFFFF 07F0000–07FFFFF SA128 0 1 0 0 0 0 0 0 0 128/64 1000000–101FFFF 0800000–080FFFF SA129 0 1 0 0 0 0 0 0 1 128/64 1020000–103FFFF 0810000–081FFFF SA130 0 1 0 0 0 0 0 1 0 128/64 1040000–105FFFF 0820000–082FFFF SA131 0 1 0 0 0 0 0 1 1 128/64 1060000–017FFFF 0830000–083FFFF N 1 1 Document Number: 002-01522 Rev. *B Page 15 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 4 of 12) Sector SA132 A24–A16 0 1 0 0 0 0 1 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1080000–109FFFF 0840000–084FFFF 0 0 128/64 SA133 0 1 0 0 0 0 1 0 1 128/64 10A0000–10BFFFF 0850000–085FFFF SA134 0 1 0 0 0 0 1 1 0 128/64 10C0000–10DFFFF 0860000–086FFFF SA135 0 1 0 0 0 0 1 1 1 128/64 10E0000–10FFFFF 0870000–087FFFF SA136 0 1 0 0 0 1 0 0 0 128/64 1100000–111FFFF 0880000–088FFFF SA137 0 1 0 0 0 1 0 0 1 128/64 1120000–113FFFF 0890000–089FFFF SA138 0 1 0 0 0 1 0 1 0 128/64 1140000–115FFFF 08A0000–08AFFFF 0 1 0 0 0 1 0 1 1 128/64 1160000–117FFFF 08B0000–08BFFFF SA140 0 1 0 0 0 1 1 0 0 128/64 1180000–119FFFF 08C0000–08CFFFF SA141 0 1 0 0 0 1 1 0 1 128/64 11A0000–11BFFFF 08D0000–08DFFFF SA142 0 1 0 0 0 1 1 1 0 128/64 11C0000–11DFFFF 08E0000–08EFFFF SA143 0 1 0 0 0 1 1 1 1 128/64 11E0000–11FFFFF SA144 0 1 0 0 1 0 0 0 0 128/64 1200000–121FFFF 0900000–090FFFF SA145 0 1 0 0 1 0 0 0 1 128/64 1220000–123FFFF 0910000–091FFFF SA146 0 1 0 0 1 0 0 1 0 128/64 1240000–125FFFF 0920000–092FFFF SA147 0 1 0 0 1 0 0 1 1 128/64 1260000–127FFFF 0930000–093FFFF SA148 0 1 0 0 1 0 1 0 0 128/64 1280000–129FFFF 0940000–094FFFF es ig n SA139 1 0 0 1 0 1 0 1 128/64 0 1 0 0 1 0 1 1 0 128/64 SA151 0 1 0 0 1 0 1 1 1 128/64 12E0000–12FFFFF 0970000–097FFFF SA152 0 1 0 0 1 1 0 0 0 128/64 1300000–131FFFF 0980000–098FFFF SA153 0 1 0 0 1 1 0 0 1 128/64 1320000–133FFFF 0990000–099FFFF SA154 0 1 0 0 1 1 0 1 0 128/64 1340000–135FFFF 09A0000–09AFFFF SA155 0 1 0 0 1 1 0 1 1 128/64 1360000–137FFFF 09B0000–09BFFFF SA156 0 1 0 0 1 1 1 0 0 128/64 1380000–139FFFF 09C0000–09CFFFF SA157 0 1 0 0 1 1 om m en 12A0000–12BFFFF 0950000–095FFFF 12C0000–12DFFFF 0960000–096FFFF 1 0 1 128/64 13A0000–13BFFFF 09D0000–09DFFFF SA158 0 1 0 0 1 1 1 1 0 128/64 13C0000–13DFFFF 09E0000–09EFFFF SA159 0 1 0 0 1 SA160 0 1 0 1 SA161 0 1 0 1 SA162 0 1 0 SA163 0 1 SA164 0 1 de d 0 SA150 ec SA149 R fo rN ew D 08F0000–08FFFFF 1 1 1 128/64 13E0000–13FFFFF 09F0000–09FFFFF 0 0 0 0 0 128/64 1400000–141FFFF 0A00000–0A0FFFF ot 1 0 0 0 1 128/64 1420000–143FFFF 0A10000–0A1FFFF 0 0 0 1 0 128/64 1440000–145FFFF 0A20000–0A2FFFF 0 1 0 0 0 1 1 128/64 1460000–147FFFF 0A30000–0A3FFFF 0 1 0 0 1 0 0 128/64 1480000–149FFFF 0A40000–0A4FFFF N 0 1 SA165 0 1 0 1 0 0 1 0 1 128/64 14A0000–14BFFFF 0A50000–0A5FFFF SA166 0 1 0 1 0 0 1 1 0 128/64 14C0000–14DFFFF 0A60000–0A6FFFF SA167 0 1 0 1 0 0 1 1 1 128/64 14E0000–14FFFFF 0A70000–0A7FFFF SA168 0 1 0 1 0 1 0 0 0 128/64 1500000–151FFFF 0A80000–0A8FFFF SA169 0 1 0 1 0 1 0 0 1 128/64 1520000–153FFFF 0A90000–0A9FFFF SA170 0 1 0 1 0 1 0 1 0 128/64 1540000–155FFFF 0AA0000–0AAFFFF SA171 0 1 0 1 0 1 0 1 1 128/64 1560000–157FFFF 0AB0000–0ABFFFF SA172 0 1 0 1 0 1 1 0 0 128/64 1580000–159FFFF 0AC0000–0ACFFFF SA173 0 1 0 1 0 1 1 0 1 128/64 15A0000–15BFFFF 0AD0000–0ADFFFF SA174 0 1 0 1 0 1 1 1 0 128/64 15C0000–15DFFFF 0AE0000–0AEFFFF SA175 0 1 0 1 0 1 1 1 1 128/64 15E0000–15FFFFF 0AF0000–0AFFFFF SA176 0 1 0 1 1 0 0 0 0 128/64 160000–161FFFF 0B00000–0B0FFFF Document Number: 002-01522 Rev. *B Page 16 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 5 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0 1 0 1 1 0 0 0 1 128/64 1620000–163FFFF 0B10000–0B1FFFF SA178 0 1 0 1 1 0 0 1 0 128/64 1640000–165FFFF 0B20000–0B2FFFF SA179 0 1 0 1 1 0 0 1 1 128/64 1660000–167FFFF 0B30000–0B3FFFF SA180 0 1 0 1 1 0 1 0 0 128/64 1680000–169FFFF 0B40000–0B4FFFF SA181 0 1 0 1 1 0 1 0 1 128/64 16A0000–16BFFFF 0B50000–0B5FFFF SA182 0 1 0 1 1 0 1 1 0 128/64 16C0000–16DFFFF 0B60000–0B6FFFF SA183 0 1 0 1 1 0 1 1 1 128/64 16E0000–16FFFFF 0B70000–0B7FFFF SA184 0 1 0 1 1 1 0 0 0 128/64 1700000–171FFFF 0B80000–0B8FFFF SA185 0 1 0 1 1 1 0 0 1 128/64 1720000–173FFFF 0B90000–0B9FFFF SA186 0 1 0 1 1 1 0 1 0 128/64 1740000–175FFFF SA187 0 1 0 1 1 1 0 1 1 128/64 1760000–177FFFF SA188 0 1 0 1 1 1 1 0 0 128/64 1780000–179FFFF SA189 0 1 0 1 1 1 1 0 1 128/64 17A0000–17BFFFF 0BD0000–0BDFFFF 0BE0000–0BEFFFF ig n SA177 0BA0000–0BAFFFF es 0BB0000–0BBFFFF 1 0 1 1 1 1 1 0 128/64 17C0000–17DFFFF 0 1 0 1 1 1 1 1 1 128/64 17E0000–17FFFFF 0BF0000–0BFFFFF SA192 0 1 1 0 0 0 0 0 0 128/64 1800000–181FFFF 0C00000–0C0FFFF SA193 0 1 1 0 0 0 0 0 1 128/64 1820000–183FFFF 0C10000–0C1FFFF SA194 0 1 1 0 0 0 0 1 0 128/64 SA195 0 1 1 0 0 0 0 1 1 128/64 SA196 0 1 1 0 0 0 1 0 0 128/64 1880000–189FFFF 0C40000–0C4FFFF SA197 0 1 1 0 0 0 1 0 1 128/64 18A0000–18BFFFF 0C50000–0C5FFFF SA198 0 1 1 0 0 0 1 1 0 128/64 0C60000–0C6FFFF 0 1 1 0 0 0 1 1 1 128/64 18E0000–18FFFFF 0C70000–0C7FFFF SA200 0 1 1 0 0 1 0 0 0 128/64 1900000–191FFFF 0C80000–0C8FFFF SA201 0 1 1 0 0 1 0 0 1 128/64 1920000–193FFFF 0C90000–0C9FFFF SA202 0 1 1 0 0 1 om m en 18C0000–18DFFFF SA199 0 1 0 128/64 1940000–195FFFF 0CA0000–0CAFFFF SA203 0 1 1 0 0 1 0 1 1 128/64 1960000–197FFFF 0CB0000–0CBFFFF SA204 0 1 1 0 0 SA205 0 1 1 0 SA206 0 1 1 0 SA207 0 1 1 SA208 0 1 SA209 0 1 de d fo rN ew 0 SA191 ec SA190 R D 0BC0000–0BCFFFF 1840000–185FFFF 0C20000–0C2FFFF 1860000–187FFFF 0C30000–0C3FFFF 1 0 0 128/64 1980000–199FFFF 0CC0000–0CCFFFF 0 1 1 0 1 128/64 19A0000–19BFFFF 0CD0000–0CDFFFF ot 1 1 1 1 0 128/64 19C0000–19DFFFF 0CE0000–0CEFFFF 0 1 1 1 1 128/64 19E0000–19FFFFF 0CF0000–0CFFFFF 1 0 1 0 0 0 0 128/64 1A00000–1A1FFFF 0D00000–0D0FFFF 1 0 1 0 0 0 1 128/64 1A20000–1A3FFFF 0D10000–0D1FFFF N 0 0 SA210 0 1 1 0 1 0 0 1 0 128/64 1A40000–1A5FFFF 0D20000–0D2FFFF SA211 0 1 1 0 1 0 0 1 1 128/64 1A60000–1A7FFFF 0D30000–0D3FFFF SA212 0 1 1 0 1 0 1 0 0 128/64 1A80000–1A9FFFF 0D40000–0D4FFFF SA213 0 1 1 0 1 0 1 0 1 128/64 1AA0000–1ABFFFF 0D50000–0D5FFFF SA214 0 1 1 0 1 0 1 1 0 128/64 1AC0000–1ADFFFF 0D60000–0D6FFFF SA215 0 1 1 0 1 0 1 1 1 128/64 1AE0000–1AFFFFF 0D70000–0D7FFFF SA216 0 1 1 0 1 1 0 0 0 128/64 1B00000–1B1FFFF 0D80000–0D8FFFF SA217 0 1 1 0 1 1 0 0 1 128/64 1B20000–1B3FFFF 0D90000–0D9FFFF SA218 0 1 1 0 1 1 0 1 0 128/64 1B40000–1B5FFFF 0DA0000–0DAFFFF SA219 0 1 1 0 1 1 0 1 1 128/64 1B60000–1B7FFFF 0DB0000–0DBFFFF SA220 0 1 1 0 1 1 1 0 0 128/64 1B80000–1B9FFFF 0DC0000–0DCFFFF SA221 0 1 1 0 1 1 1 0 1 128/64 1BA0000–1BBFFFF 0DD0000–0DDFFFF Document Number: 002-01522 Rev. *B Page 17 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 6 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0 1 1 0 1 1 1 1 0 128/64 1BC0000–1BDFFFF 0DE0000–0DEFFFF SA223 0 1 1 0 1 1 1 1 1 128/64 1BE0000–1BFFFFF 0DF0000–0DFFFFF SA224 0 1 1 1 0 0 0 0 0 128/64 1C00000–1C1FFFF 0E00000–0E0FFFF SA225 0 1 1 1 0 0 0 0 1 128/64 1C20000–1C3FFFF 0E10000–0E1FFFF SA226 0 1 1 1 0 0 0 1 0 128/64 1C40000–1C5FFFF 0E20000–0E2FFFF SA227 0 1 1 1 0 0 0 1 1 128/64 1C60000–1C7FFFF 0E30000–0E3FFFF SA228 0 1 1 1 0 0 1 0 0 128/64 1C80000–1C9FFFF 0E40000–0E4FFFF SA229 0 1 1 1 0 0 1 0 1 128/64 1CA0000–1CBFFFF 0E50000–0E5FFFF SA230 0 1 1 1 0 0 1 1 0 128/64 1CC0000–1CDFFFF 0E60000–0E6FFFF SA231 0 1 1 1 0 0 1 1 1 128/64 1CE0000–1CFFFFF SA232 0 1 1 1 0 1 0 0 0 128/64 1D00000–1D1FFFF SA233 0 1 1 1 0 1 0 0 1 128/64 1D20000–1D3FFFF SA234 0 1 1 1 0 1 0 1 0 128/64 1D40000–1D5FFFF ig n SA222 0E70000–0E7FFFF es 0E80000–0E8FFFF D 0E90000–0E9FFFF 0EA0000–0EAFFFF 0 1 1 1 0 1 0 1 1 128/64 1D60000–1D7FFFF 0EB0000–0EBFFFF SA236 0 1 1 1 0 1 1 0 0 128/64 1D80000–1D9FFFF 0EC0000–0ECFFFF SA237 0 1 1 1 0 1 1 0 1 128/64 1DA0000–1DBFFFF 0ED0000–0EDFFFF SA238 0 1 1 1 0 1 1 1 0 128/64 1DC0000–1DDFFFF 0EE0000–0EEFFFF SA239 0 1 1 1 0 1 1 1 1 128/64 SA240 0 1 1 1 1 0 0 0 0 128/64 SA241 0 1 1 1 1 0 0 0 1 SA242 0 1 1 1 1 0 0 1 0 SA243 0 1 1 1 1 0 0 1 1 SA244 0 1 1 1 1 0 1 0 0 SA245 0 1 1 1 1 0 1 0 SA246 0 1 1 1 1 0 1 1 0EF0000–0EFFFFF 1E00000–1E1FFFF 0F00000–0F0FFFF 128/64 1E20000–1E3FFFF 0F10000–0F1FFFF 128/64 1E40000–1E5FFFF 0F20000–0F2FFFF 128/64 1E60000–1E7FFFF 0F30000–0F3FFFF 128/64 1E80000–1E9FFFF 0F40000–0F4FFFF 1 128/64 1EA0000–1EBFFFF 0F50000–0F5FFFF 0 128/64 1EC0000–1EDFFFF 0F60000–0F6FFFF 0 1 1 1 1 0 1 1 1 128/64 1EE0000–1EFFFFF 0F70000–0F7FFFF SA248 0 1 1 1 1 1 0 0 0 128/64 1F00000–1F1FFFF 0F80000–0F8FFFF SA249 0 1 1 1 1 SA250 0 1 1 1 SA251 0 1 1 1 SA252 0 1 1 SA253 0 1 SA254 0 1 SA255 0 SA256 1 SA257 ec SA247 R de d 1DE0000–1DFFFFF om m en fo rN ew SA235 0 0 1 128/64 1F20000–1F3FFFF 0F90000–0F9FFFF 1 1 0 1 0 128/64 1F40000–1F5FFFF 0FA0000–0FAFFFF ot 1 1 0 1 1 128/64 1F60000–1F7FFFF 0FB0000–0FBFFFF 1 1 1 0 0 128/64 1F80000–1F9FFFF 0FC0000–0FCFFFF 1 1 1 1 1 0 1 128/64 1FA0000–1FBFFFF 0FD0000–0FDFFFF 1 1 1 1 1 1 0 128/64 1FC0000–1FDFFFF 0FE0000–0FEFFFF 1 1 1 1 1 1 1 1 128/64 1FE0000–1FFFFFF 0FF0000–0FFFFFF 0 0 0 0 0 0 0 0 128/64 2000000–201FFFF 1000000–100FFFF 1 0 0 0 0 0 0 0 1 128/64 2020000–203FFFF 1010000–101FFFF SA258 1 0 0 0 0 0 0 1 0 128/64 2040000–205FFFF 1020000–102FFFF SA259 1 0 0 0 0 0 0 1 1 128/64 2060000–207FFFF 1030000–103FFFF SA260 1 0 0 0 0 0 1 0 0 128/64 2080000–209FFFF 1040000–104FFFF SA261 1 0 0 0 0 0 1 0 1 128/64 20A0000–20BFFFF 1050000–105FFFF SA262 1 0 0 0 0 0 1 1 0 128/64 20C0000–20DFFFF 1060000–106FFFF SA263 1 0 0 0 0 0 1 1 1 128/64 20E0000–20FFFFF 1070000–107FFFF SA264 1 0 0 0 0 1 0 0 0 128/64 2100000–211FFFF 1080000–108FFFF SA265 1 0 0 0 0 1 0 0 1 128/64 2120000–213FFFF 1090000–109FFFF SA266 1 0 0 0 0 1 0 1 0 128/64 2140000–215FFFF 10A0000–10AFFFF N 1 1 Document Number: 002-01522 Rev. *B Page 18 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 7 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 2160000–217FFFF 10B0000–10BFFFF SA267 1 0 0 0 0 1 0 1 1 128/64 SA268 1 0 0 0 0 1 1 0 0 128/64 2180000–219FFFF 10C0000–10CFFFF SA269 1 0 0 0 0 1 1 0 1 128/64 21A0000–21BFFFF 10D0000–10DFFFF 1 0 0 0 0 1 1 1 0 128/64 21C0000–21DFFFF 10E0000–10EFFFF SA271 1 0 0 0 0 1 1 1 1 128/64 21E0000–21FFFFF 10F0000–10FFFFF SA272 1 0 0 0 1 0 0 0 0 128/64 2200000–221FFFF 1100000–110FFFF SA273 1 0 0 0 1 0 0 0 1 128/64 2220000–223FFFF 1110000–111FFFF SA274 1 0 0 0 1 0 0 1 0 128/64 2240000–225FFFF 1120000–112FFFF SA275 1 0 0 0 1 0 0 1 1 128/64 2260000–227FFFF 1130000–113FFFF SA276 1 0 0 0 1 0 1 0 0 128/64 2280000–229FFFF SA277 1 0 0 0 1 0 1 0 1 128/64 22A0000–22BFFFF SA278 1 0 0 0 1 0 1 1 0 128/64 22C0000–22DFFFF SA279 1 0 0 0 1 0 1 1 1 128/64 22E0000–22FFFFF 1170000–117FFFF SA280 1 0 0 0 1 1 0 0 0 128/64 2300000–231FFFF 1180000–118FFFF SA281 1 0 0 0 1 1 0 0 1 128/64 2320000–233FFFF 1190000–119FFFF SA282 1 0 0 0 1 1 0 1 0 128/64 2340000–235FFFF 11A0000–11AFFFF SA283 1 0 0 0 1 1 0 1 1 128/64 2360000–237FFFF 11B0000–11BFFFF SA284 1 0 0 0 1 1 1 0 0 128/64 SA285 1 0 0 0 1 1 1 0 1 128/64 1 1 1 1 0 0 1 1 1 1 1 SA288 1 0 0 1 0 0 0 0 0 SA289 1 0 0 1 0 0 0 0 1 SA290 1 0 0 1 0 0 0 1 SA291 1 0 0 1 0 0 0 SA292 1 0 0 1 0 0 SA293 1 0 0 1 0 0 SA294 1 0 0 1 0 0 SA295 1 0 0 1 0 0 SA296 1 0 0 1 SA297 1 0 0 SA298 1 0 SA299 1 SA300 SA301 es D ew rN fo 2380000–239FFFF 11C0000–11CFFFF 23A0000–23BFFFF 11D0000–11DFFFF d 0 0 128/64 23C0000–23DFFFF 11E0000–11EFFFF 128/64 23E0000–23FFFFF 11F0000–11FFFFF 128/64 2400000–241FFFF 1200000–120FFFF 128/64 2420000–243FFFF 1210000–121FFFF 0 128/64 2440000–245FFFF 1220000–122FFFF 1 1 128/64 2460000–247FFFF 1230000–123FFFF 1 0 0 128/64 2480000–249FFFF 1240000–124FFFF 1 0 1 128/64 24A0000–24BFFFF 1250000–125FFFF 1 1 0 128/64 24C0000–24DFFFF 1260000–126FFFF 1 1 1 128/64 24E0000–24FFFFF 1270000–127FFFF 1280000–128FFFF ot de 0 0 1160000–116FFFF om m en 0 1 ec 1 SA287 1140000–114FFFF 1150000–115FFFF R SA286 ig n SA270 1 0 0 0 128/64 2500000–251FFFF 0 1 0 0 1 128/64 2520000–253FFFF 1290000–129FFFF 0 1 0 1 0 1 0 128/64 2540000–255FFFF 12A0000–12AFFFF 0 0 1 0 1 0 1 1 128/64 2560000–257FFFF 12B0000–12BFFFF 1 0 0 1 0 1 1 0 0 128/64 2580000–259FFFF 12C0000–12CFFFF 1 0 0 1 0 1 1 0 1 128/64 25A0000–25BFFFF 12D0000–12DFFFF N 0 1 SA302 1 0 0 1 0 1 1 1 0 128/64 25C0000–25DFFFF 12E0000–12EFFFF SA303 1 0 0 1 0 1 1 1 1 128/64 25E0000–25FFFFF 12F0000–12FFFFF SA304 1 0 0 1 1 0 0 0 0 128/64 2600000–261FFFF 1300000–130FFFF SA305 1 0 0 1 1 0 0 0 1 128/64 2620000–263FFFF 1310000–131FFFF SA306 1 0 0 1 1 0 0 1 0 128/64 2640000–265FFFF 1320000–132FFFF SA307 1 0 0 1 1 0 0 1 1 128/64 2660000–267FFFF 1330000–133FFFF SA308 1 0 0 1 1 0 1 0 0 128/64 2680000–269FFFF 1340000–134FFFF SA309 1 0 0 1 1 0 1 0 1 128/64 26A0000–26BFFFF 1350000–135FFFF SA310 1 0 0 1 1 0 1 1 0 128/64 26C0000–26DFFFF 1360000–136FFFF SA311 1 0 0 1 1 0 1 1 1 128/64 26E0000–26FFFFF 1370000–137FFFF Document Number: 002-01522 Rev. *B Page 19 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 8 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1380000–138FFFF 1 0 0 1 1 1 0 0 0 128/64 2700000–271FFFF SA313 1 0 0 1 1 1 0 0 1 128/64 2720000–273FFFF 1390000–139FFFF SA314 1 0 0 1 1 1 0 1 0 128/64 2740000–275FFFF 13A0000–13AFFFF SA315 1 0 0 1 1 1 0 1 1 128/64 2760000–277FFFF 13B0000–13BFFFF SA316 1 0 0 1 1 1 1 0 0 128/64 2780000–279FFFF 13C0000–13CFFFF SA317 1 0 0 1 1 1 1 0 1 128/64 27A0000–27BFFFF 13D0000–13DFFFF SA318 1 0 0 1 1 1 1 1 0 128/64 27C0000–27DFFFF 13E0000–13EFFFF SA319 1 0 0 1 1 1 1 1 1 128/64 27E0000–27FFFFF 13F0000–13FFFFF SA320 1 0 1 0 0 0 0 0 0 128/64 2800000–281FFFF 1400000–140FFFF SA321 1 0 1 0 0 0 0 0 1 128/64 2820000–283FFFF SA322 1 0 1 0 0 0 0 1 0 128/64 2840000–285FFFF SA323 1 0 1 0 0 0 0 1 1 128/64 2860000–287FFFF SA324 1 0 1 0 0 0 1 0 0 128/64 2880000–289FFFF 1440000–144FFFF ig n SA312 1410000–141FFFF es 1420000–142FFFF 1 0 1 0 0 0 1 0 1 128/64 28A0000–28BFFFF 1450000–145FFFF SA326 1 0 1 0 0 0 1 1 0 128/64 28C0000–28DFFFF 1460000–146FFFF SA327 1 0 1 0 0 0 1 1 1 128/64 28E0000–28FFFFF 1470000–147FFFF SA328 1 0 1 0 0 1 0 0 0 128/64 2900000–291FFFF 1480000–148FFFF SA329 1 0 1 0 0 1 0 0 1 128/64 SA330 1 0 1 0 0 1 0 1 0 128/64 SA331 1 0 1 0 0 1 0 1 1 128/64 2960000–297FFFF 14B0000–14BFFFF SA332 1 0 1 0 0 1 1 0 0 128/64 2980000–299FFFF 14C0000–14CFFFF SA333 1 0 1 0 0 1 1 0 1 128/64 29A0000–29BFFFF 14D0000–14DFFFF SA334 1 0 1 0 0 1 1 1 0 128/64 29C0000–29DFFFF 14E0000–14EFFFF SA335 1 0 1 0 0 1 1 1 1 128/64 29E0000–29FFFFF 14F0000–14FFFFF SA336 1 0 1 0 1 0 0 0 0 128/64 2A00000–2A1FFFF 1500000–150FFFF SA337 1 0 1 0 1 0 0 0 1 128/64 2A20000–2A3FFFF 1510000–151FFFF SA338 1 0 1 0 1 0 0 1 0 128/64 2A40000–2A5FFFF 1520000–152FFFF SA339 1 0 1 0 1 SA340 1 0 1 0 1 0 1 1 0 1 SA343 1 0 SA344 1 SA345 SA346 0 rN fo d de om m en ec 2920000–293FFFF 1490000–149FFFF 2940000–295FFFF 14A0000–14AFFFF 0 0 1 1 128/64 2A60000–2A7FFFF 1530000–153FFFF 0 1 0 0 128/64 2A80000–2A9FFFF 1540000–154FFFF ot 1 SA342 1 0 1 0 1 128/64 2AA0000–2ABFFFF 1550000–155FFFF 0 1 0 1 1 0 128/64 2AC0000–2ADFFFF 1560000–156FFFF 1 0 1 0 1 1 1 128/64 2AE00000–2EFFFFF 1570000–157FFFF 0 1 0 1 1 0 0 0 128/64 2B00000–2B1FFFF 1580000–158FFFF 1 0 1 0 1 1 0 0 1 128/64 2B20000–2B3FFFF 1590000–159FFFF 1 0 1 0 1 1 0 1 0 128/64 2B40000–2B5FFFF 15A0000–15AFFFF SA347 1 0 1 0 1 1 0 1 1 128/64 2B60000–2B7FFFF 15B0000–15BFFFF SA348 1 0 1 0 1 1 1 0 0 128/64 2B80000–2B9FFFF 15C0000–15CFFFF N SA341 ew SA325 R D 1430000–143FFFF SA349 1 0 1 0 1 1 1 0 1 128/64 2BA0000–2BBFFFF 15D0000–15DFFFF SA350 1 0 1 0 1 1 1 1 0 128/64 2BC0000–2DFFFFF 15E0000–15EFFFF SA351 1 0 1 0 1 1 1 1 1 128/64 2BE0000–2BFFFFF 15F0000–15FFFFF SA352 1 0 1 1 0 0 0 0 0 128/64 2C00000–2C1FFFF 1600000–160FFFF SA353 1 0 1 1 0 0 0 0 1 128/64 2C20000–2C3FFFF 1610000–161FFFF SA354 1 0 1 1 0 0 0 1 0 128/64 2C40000–2C5FFFF 1620000–162FFFF SA355 1 0 1 1 0 0 0 1 1 128/64 2C60000–2C7FFFF 1630000–163FFFF SA356 1 0 1 1 0 0 1 0 0 128/64 2C80000–2C9FFFF 1640000–164FFFF Document Number: 002-01522 Rev. *B Page 20 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 9 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1650000–165FFFF 1 0 1 1 0 0 1 0 1 128/64 2CA0000–2CBFFFF SA358 1 0 1 1 0 0 1 1 0 128/64 2CC0000–2CDFFFF 1660000–166FFFF SA359 1 0 1 1 0 0 1 1 1 128/64 2CE0000–2CFFFFF 1670000–167FFFF SA360 1 0 1 1 0 1 0 0 0 128/64 2D00000–2D1FFFF 1680000–168FFFF SA361 1 0 1 1 0 1 0 0 1 128/64 2D20000–2D3FFFF 1690000–169FFFF SA362 1 0 1 1 0 1 0 1 0 128/64 2D40000–2D5FFFF 16A0000–16AFFFF SA363 1 0 1 1 0 1 0 1 1 128/64 2D60000–2D7FFFF 16B0000–16BFFFF SA364 1 0 1 1 0 1 1 0 0 128/64 2D80000–2D9FFFF 16C0000–16CFFFF SA365 1 0 1 1 0 1 1 0 1 128/64 2DA0000–2DBFFFF 16D0000–16DFFFF SA366 1 0 1 1 0 1 1 1 0 128/64 2DC0000–2DDFFFF 16E0000–16EFFFF SA367 1 0 1 1 0 1 1 1 1 128/64 2DE0000–2DFFFFF SA368 1 0 1 1 1 0 0 0 0 128/64 2E00000–2E1FFFF SA369 1 0 1 1 1 0 0 0 1 128/64 2E20000–2E3FFFF 1710000–171FFFF SA370 1 0 1 1 1 0 0 1 0 128/64 2E40000–2E5FFFF 1720000–172FFFF SA371 1 0 1 1 1 0 0 1 1 128/64 2E60000–2E7FFFF 1730000–173FFFF SA372 1 0 1 1 1 0 1 0 0 128/64 2E80000–2E9FFFF 1740000–174FFFF SA373 1 0 1 1 1 0 1 0 1 128/64 2EA0000–2EBFFFF 1750000–175FFFF SA374 1 0 1 1 1 0 1 1 0 128/64 SA375 1 0 1 1 1 0 1 1 1 128/64 SA376 1 0 1 1 1 1 0 0 0 SA377 1 0 1 1 1 1 0 0 1 SA378 1 0 1 1 1 1 0 1 0 SA379 1 0 1 1 1 1 0 1 1 SA380 1 0 1 1 1 1 1 0 SA381 1 0 1 1 1 1 1 SA382 1 0 1 1 1 1 SA383 1 0 1 1 1 1 SA384 1 1 0 0 0 SA385 1 1 0 0 SA386 1 1 0 0 SA387 1 1 0 SA388 1 1 SA389 1 SA390 SA391 ig n SA357 es 16F0000–16FFFFF 1770000–177FFFF 128/64 2F00000–2F1FFFF 1780000–178FFFF 128/64 2F20000–2F3FFFF 1790000–179FFFF 128/64 om m en 2F40000–2F5FFFF 17A0000–17AFFFF 128/64 2F60000–2F7FFFF 17B0000–17BFFFF 0 128/64 2F80000–2F9FFFF 17C0000–17CFFFF 0 1 128/64 2FA0000–2FBFFFF 17D0000–17DFFFF 1 1 0 128/64 2FC0000–2FDFFFF 17E0000–17EFFFF 1 1 1 128/64 3FE0000–3FFFFFF 17F0000–17FFFFF de d 1760000–176FFFF 2EE0000–2EFFFFF ec 2EC0000–2EDFFFF R fo rN ew D 1700000–170FFFF 0 0 0 128/64 3000000–301FFFF 1800000–180FFFF 0 0 0 0 1 128/64 3020000–303FFFF 1810000–181FFFF ot 0 0 0 1 0 128/64 3040000–305FFFF 1820000–182FFFF 0 0 0 1 1 128/64 3060000–307FFFF 1830000–183FFFF 0 0 0 0 1 0 0 128/64 3080000–309FFFF 1840000–184FFFF 1 0 0 0 0 1 0 1 128/64 30A0000–30BFFFF 1850000–185FFFF 1 1 0 0 0 0 1 1 0 128/64 30C0000–30DFFFF 1860000–186FFFF 1 1 0 0 0 0 1 1 1 128/64 30E0000–30FFFFF 1870000–187FFFF SA392 1 1 0 0 0 1 0 0 0 128/64 3100000–311FFFF 1880000–188FFFF SA393 1 1 0 0 0 1 0 0 1 128/64 3120000–313FFFF 1890000–189FFFF SA394 1 1 0 0 0 1 0 1 0 128/64 3140000–315FFFF 18A0000–18AFFFF SA395 1 1 0 0 0 1 0 1 1 128/64 3160000–317FFFF 18B0000–18BFFFF SA396 1 1 0 0 0 1 1 0 0 128/64 3180000–319FFFF 18C0000–18CFFFF SA397 1 1 0 0 0 1 1 0 1 128/64 31A0000–31BFFFF 18D0000–18DFFFF N 0 0 SA398 1 1 0 0 0 1 1 1 0 128/64 31C0000–31DFFFF 18E0000–18EFFFF SA399 1 1 0 0 0 1 1 1 1 128/64 31E0000–31FFFFF 18F0000–18FFFFF SA400 1 1 0 0 1 0 0 0 0 128/64 3200000–321FFFF 1900000–190FFFF SA401 1 1 0 0 1 0 0 0 1 128/64 3220000–323FFFF 1910000–191FFFF Document Number: 002-01522 Rev. *B Page 21 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 10 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1 1 0 0 1 0 0 1 0 128/64 3240000–325FFFF 1920000–192FFFF SA403 1 1 0 0 1 0 0 1 1 128/64 3260000–327FFFF 1930000–193FFFF SA404 1 1 0 0 1 0 1 0 0 128/64 3280000–329FFFF 1940000–194FFFF SA405 1 1 0 0 1 0 1 0 1 128/64 32A0000–32BFFFF 1950000–195FFFF SA406 1 1 0 0 1 0 1 1 0 128/64 32C0000–32DFFFF 1960000–196FFFF SA407 1 1 0 0 1 0 1 1 1 128/64 32E0000–32FFFFF 1970000–197FFFF SA408 1 1 0 0 1 1 0 0 0 128/64 3300000–331FFFF 1980000–198FFFF SA409 1 1 0 0 1 1 0 0 1 128/64 3320000–333FFFF 1990000–199FFFF SA410 1 1 0 0 1 1 0 1 0 128/64 3340000–335FFFF 19A0000–19AFFFF ig n SA402 SA411 1 1 0 0 1 1 0 1 1 128/64 3360000–337FFFF SA412 1 1 0 0 1 1 1 0 0 128/64 3380000–339FFFF 19B0000–19BFFFF SA413 1 1 0 0 1 1 1 0 1 128/64 33A0000–33BFFFF SA414 1 1 0 0 1 1 1 1 0 128/64 33C0000–33DFFFF SA415 1 1 0 0 1 1 1 1 1 128/64 33E0000–33FFFFF 19F0000–19FFFFF SA416 1 1 0 1 0 0 0 0 0 128/64 3400000–341FFFF 1A00000–1A0FFFF SA417 1 1 0 1 0 0 0 0 1 128/64 3420000–343FFFF 1A10000–1A1FFFF SA418 1 1 0 1 0 0 0 1 0 128/64 3440000–345FFFF 1A20000–1A2FFFF SA419 1 1 0 1 0 0 0 1 1 128/64 SA420 1 1 0 1 0 0 1 0 0 128/64 SA421 1 1 0 1 0 0 1 0 1 SA422 1 1 0 1 0 0 1 1 0 SA423 1 1 0 1 0 0 1 1 1 SA424 1 1 0 1 0 1 0 0 0 SA425 1 1 0 1 0 1 0 0 1 128/64 3520000–353FFFF 1A90000–1A9FFFF SA426 1 1 0 1 0 1 0 1 0 128/64 3540000–355FFFF 1AA0000–1AAFFFF es 19C0000–19CFFFF fo rN ew D 19D0000–19DFFFF 1A30000–1A3FFFF 1A40000–1A4FFFF 128/64 34A0000–34BFFFF 1A50000–1A5FFFF 128/64 34C0000–34DFFFF 1A60000–1A6FFFF 128/64 34E0000–34FFFFF 1A70000–1A7FFFF 128/64 3500000–351FFFF 1A80000–1A8FFFF 1 1 0 1 0 1 0 1 1 128/64 3560000–357FFFF 1AB0000–1ABFFFF SA428 1 1 0 1 0 1 1 0 0 128/64 3580000–359FFFF 1AC0000–1ACFFFF SA429 1 1 0 1 0 1 1 0 1 128/64 35A0000–35BFFFF 1AD0000–1ADFFFF SA430 1 1 0 1 0 1 1 1 0 128/64 35C0000–35DFFFF 1AE0000–1AEFFFF SA431 1 1 0 1 SA432 1 1 0 SA433 1 1 SA434 1 SA435 SA436 ot ec SA427 R de d 3480000–349FFFF om m en 3460000–347FFFF 19E0000–19EFFFF 1 1 1 1 128/64 35E0000–35FFFFF 1AF0000–1AFFFFF 1 0 0 0 0 128/64 3600000–361FFFF 1B00000–1B0FFFF 0 1 1 0 0 0 1 128/64 3620000–363FFFF 1B10000–1B1FFFF 1 0 1 1 0 0 1 0 128/64 3640000–365FFFF 1B20000–1B2FFFF 1 1 0 1 1 0 0 1 1 128/64 3660000–367FFFF 1B30000–1B3FFFF 1 1 0 1 1 0 1 0 0 128/64 3680000–369FFFF 1B40000–1B4FFFF SA437 1 1 0 1 1 0 1 0 1 128/64 36A0000–36BFFFF 1B50000–1B5FFFF SA438 1 1 0 1 1 0 1 1 0 128/64 36C0000–36DFFFF 1B60000–1B6FFFF SA439 1 1 0 1 1 0 1 1 1 128/64 36E0000–36FFFFF 1B70000–1B7FFFF SA440 1 1 0 1 1 1 0 0 0 128/64 3700000–371FFFF 1B80000–1B8FFFF SA441 1 1 0 1 1 1 0 0 1 128/64 3720000–373FFFF 1B90000–1B9FFFF SA442 1 1 0 1 1 1 0 1 0 128/64 3740000–375FFFF 1BA0000–1BAFFFF N 0 1 SA443 1 1 0 1 1 1 0 1 1 128/64 3760000–377FFFF 1BB0000–1BBFFFF SA444 1 1 0 1 1 1 1 0 0 128/64 3780000–379FFFF 1BC0000–1BCFFFF SA445 1 1 0 1 1 1 1 0 1 128/64 37A0000–37BFFFF 1BD0000–1BDFFFF SA446 1 1 0 1 1 1 1 1 0 128/64 37C0000–37DFFFF 1BE0000–1BEFFFF Document Number: 002-01522 Rev. *B Page 22 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 11 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1 1 0 1 1 1 1 1 1 128/64 37E0000–37FFFFF 1BF0000–1BFFFFF SA448 1 1 1 0 0 0 0 0 0 128/64 3800000–381FFFF 1C00000–1C0FFFF SA449 1 1 1 0 0 0 0 0 1 128/64 3820000–383FFFF 1C10000–1C1FFFF SA450 1 1 1 0 0 0 0 1 0 128/64 3840000–385FFFF 1C20000–1C2FFFF SA451 1 1 1 0 0 0 0 1 1 128/64 3860000–387FFFF 1C30000–1C3FFFF SA452 1 1 1 0 0 0 1 0 0 128/64 3880000–389FFFF 1C40000–1C4FFFF SA453 1 1 1 0 0 0 1 0 1 128/64 38A0000–38BFFFF 1C50000–1C5FFFF SA454 1 1 1 0 0 0 1 1 0 128/64 38C0000–38DFFFF 1C60000–1C6FFFF SA455 1 1 1 0 0 0 1 1 1 128/64 38E0000–38FFFFF 1C70000–1C7FFFF SA456 1 1 1 0 0 1 0 0 0 128/64 3900000–391FFFF 1C80000–1C8FFFF SA457 1 1 1 0 0 1 0 0 1 128/64 3920000–393FFFF SA458 1 1 1 0 0 1 0 1 0 128/64 3940000–395FFFF SA459 1 1 1 0 0 1 0 1 1 128/64 3960000–397FFFF SA460 1 1 1 0 0 1 1 0 0 128/64 3980000–399FFFF 1CC0000–1CCFFFF SA461 1 1 1 0 0 1 1 0 1 128/64 39A0000–39BFFFF 1CD0000–1CDFFFF SA462 1 1 1 0 0 1 1 1 0 128/64 39C0000–39DFFFF 1CE0000–1CEFFFF SA463 1 1 1 0 0 1 1 1 1 128/64 39E0000–39FFFFF 1CF0000–1CFFFFF SA464 1 1 1 0 1 0 0 0 0 128/64 SA465 1 1 1 0 1 0 0 0 1 128/64 SA466 1 1 1 0 1 0 0 1 0 SA467 1 1 1 0 1 0 0 1 1 SA468 1 1 1 0 1 0 1 0 0 SA469 1 1 1 0 1 0 1 0 1 SA470 1 1 1 0 1 0 1 1 SA471 1 1 1 0 1 0 1 SA472 1 1 1 0 1 1 SA473 1 1 1 0 1 1 SA474 1 1 1 0 1 SA475 1 1 1 0 1 SA476 1 1 1 SA477 1 1 1 SA478 1 1 SA479 1 1 SA480 1 SA481 1 SA482 es 1C90000–1C9FFFF 1CB0000–1CBFFFF 1D10000–1D1FFFF 128/64 3A40000–3A5FFFF 1D20000–1D2FFFF 128/64 3A60000–3A7FFFF 1D30000–1D3FFFF 128/64 3A80000–3A9FFFF 1D40000–1D4FFFF 128/64 3AA0000–3ABFFFF 1D50000–1D5FFFF 0 128/64 3AC0000–3ADFFFF 1D60000–1D6FFFF 1 1 128/64 3AE0000–3AFFFFF 1D70000–1D7FFFF 0 0 0 128/64 3B00000–3B1FFFF 1D80000–1D8FFFF 0 0 1 128/64 3B20000–3B3FFFF 1D90000–1D9FFFF ec om m en de d 1D00000–1D0FFFF 3A20000–3A3FFFF R fo rN ew D 1CA0000–1CAFFFF 3A00000–3A1FFFF 0 1 0 128/64 3B40000–3B5FFFF 1DA0000–1DAFFFF 1 0 1 1 128/64 3B60000–3B7FFFF 1DB0000–1DBFFFF ot 1 1 1 1 0 0 128/64 3B80000–3B9FFFF 1DC0000–1DCFFFF 0 1 1 1 0 1 128/64 3BA0000–3BBFFFF 1DD0000–1DDFFFF 1 0 1 1 1 1 0 128/64 3BC0000–3BDFFFF 1DE0000–1DEFFFF 1 0 1 1 1 1 1 128/64 3BE0000–3BFFFFF 1DF0000–1DFFFFF 1 1 1 0 0 0 0 0 128/64 3C00000–3C1FFFF 1E00000–1E0FFFF 1 1 1 0 0 0 0 1 128/64 3C20000–3C3FFFF 1E10000–1E1FFFF 1 1 1 1 0 0 0 1 0 128/64 3C40000–3C5FFFF 1E20000–1E2FFFF SA483 1 1 1 1 0 0 0 1 1 128/64 3C60000–3C7FFFF 1E30000–1E3FFFF SA484 1 1 1 1 0 0 1 0 0 128/64 3C80000–3C9FFFF 1E40000–1E4FFFF SA485 1 1 1 1 0 0 1 0 1 128/64 3CA0000–3CBFFFF 1E50000–1E5FFFF SA486 1 1 1 1 0 0 1 1 0 128/64 3CC0000–3CDFFFF 1E60000–1E6FFFF SA487 1 1 1 1 0 0 1 1 1 128/64 3CE0000–3CFFFFF 1E70000–1E7FFFF SA488 1 1 1 1 0 1 0 0 0 128/64 3D00000–3D1FFFFF 1E80000–1E8FFFF SA489 1 1 1 1 0 1 0 0 1 128/64 3D20000–3D3FFFF 1E90000–1E9FFFF SA490 1 1 1 1 0 1 0 1 0 128/64 3D40000–3D5FFFF 1EA0000–1EAFFFF SA491 1 1 1 1 0 1 0 1 1 128/64 3D60000–3D7FFFF 1EB0000–1EBFFFF N 0 ig n SA447 Document Number: 002-01522 Rev. *B Page 23 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL512N (Sheet 12 of 12) Sector A24–A16 Sector Size (Kbytes/ Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 3D80000–3D9FFFF 1EC0000–1ECFFFF 1 1 1 1 0 1 1 0 0 128/64 SA493 1 1 1 1 0 1 1 0 1 128/64 3DA0000–3DBFFFF 1ED0000–1EDFFFF SA494 1 1 1 1 0 1 1 1 0 128/64 3DC0000–3DDFFFF 1EE0000–1EEFFFF SA495 1 1 1 1 0 1 1 1 1 128/64 3DE0000–3DFFFFF 1EF0000–1EFFFFF SA496 1 1 1 1 1 0 0 0 0 128/64 3E00000–3E1FFFF 1F00000–1F0FFFF SA497 1 1 1 1 1 0 0 0 1 128/64 3E20000–3E3FFFF 1F10000–1F1FFFF SA498 1 1 1 1 1 0 0 1 0 128/64 3E40000–3E5FFFF 1F20000–1F2FFFF SA499 1 1 1 1 1 0 0 1 1 128/64 3E60000–3E7FFFF 1F30000–1F3FFFF SA500 1 1 1 1 1 0 1 0 0 128/64 3E80000–3E9FFFF 1F40000–1F4FFFF ig n SA492 SA501 1 1 1 1 1 0 1 0 1 128/64 3EA0000–3EBFFFF SA502 1 1 1 1 1 0 1 1 0 128/64 3EC00000–3EDFFFF 1F50000–1F5FFFF SA503 1 1 1 1 1 0 1 1 1 128/64 3EE0000–3EFFFFF SA504 1 1 1 1 1 1 0 0 0 128/64 3F00000–3F1FFFF SA505 1 1 1 1 1 1 0 0 1 128/64 3F20000–3F3FFFF 1F90000–1F9FFFF SA506 1 1 1 1 1 1 0 1 0 128/64 3F40000–3F5FFFF 1FA0000–1FAFFFF SA507 1 1 1 1 1 1 0 1 1 128/64 3F60000–3F7FFFF 1FB0000–1FBFFFF SA508 1 1 1 1 1 1 1 0 0 128/64 3F80000–3F9FFFF 1FC0000–1FCFFFF SA509 1 1 1 1 1 1 1 0 1 128/64 SA510 1 1 1 1 1 1 1 1 0 128/64 SA511 1 1 1 1 1 1 1 1 1 128/64 es 1F60000–1F6FFFF fo rN ew D 1F70000–1F7FFFF 1FD0000–1FDFFFF 1FE0000–1FEFFFF 3FE0000–3FFFFFF 1FF0000–1FFFFFF d 3FA0000–3FBFFFF 3FC0000–3FDFFFF N ot R ec om m en de 1F80000–1F8FFFF Document Number: 002-01522 Rev. *B Page 24 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL256N (Sheet 1 of 6) Sector A23–A16 Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0 0 0 0 0 0 0 0 128/64 0000000–001FFFF 0000000–000FFFF SA1 0 0 0 0 0 0 0 1 128/64 0020000–003FFFF 0010000–001FFFF SA2 0 0 0 0 0 0 1 0 128/64 0040000–005FFFF 0020000–002FFFF SA3 0 0 0 0 0 0 1 1 128/64 0060000–007FFFF 0030000–003FFFF SA4 0 0 0 0 0 1 0 0 128/64 0080000–009FFFF 0040000–004FFFF SA5 0 0 0 0 0 1 0 1 128/64 00A0000–00BFFFF 0050000–005FFFF SA6 0 0 0 0 0 1 1 0 128/64 00C0000–00DFFFF 0060000–006FFFF SA7 0 0 0 0 0 1 1 1 128/64 00E0000–00FFFFF 0070000–007FFFF SA8 0 0 0 0 1 0 0 0 128/64 0100000–011FFFF 0080000–008FFFF ig n SA0 0 0 0 0 1 0 0 1 128/64 0120000–013FFFF 0090000–009FFFF 0 0 0 0 1 0 1 0 128/64 0140000–015FFFF 00A0000–00AFFFF es SA9 SA10 0 0 0 0 1 0 1 1 128/64 0160000–017FFFF 0 0 0 0 1 1 0 0 128/64 0180000–019FFFF 00B0000–00BFFFF SA13 0 0 0 0 1 1 0 1 128/64 01A0000–01BFFFF 00D0000–00DFFFF SA14 0 0 0 0 1 1 1 0 128/64 01C0000–01DFFFF 00E0000–00EFFFF SA15 0 0 0 0 1 1 1 1 128/64 01E0000–01FFFFF 00F0000–00FFFFF SA16 0 0 0 1 0 0 0 0 128/64 0200000–021FFFF 0100000–010FFFF SA17 0 0 0 1 0 0 0 1 128/64 SA18 0 0 0 1 0 0 1 0 128/64 SA19 0 0 0 1 0 0 1 1 SA20 0 0 0 1 0 1 0 0 SA21 0 0 0 1 0 1 0 1 128/64 02A0000–02BFFFF 0150000–015FFFF SA22 0 0 0 1 0 1 1 0 128/64 02C0000–02DFFFF 0160000–016FFFF SA23 0 0 0 1 0 1 1 1 128/64 02E0000–02FFFFF 0170000–017FFFF SA24 0 0 0 1 1 0 0 0 128/64 0300000–031FFFF 0180000–018FFFF SA25 0 0 0 1 1 0 SA26 0 0 0 1 1 SA27 0 0 0 1 1 SA28 0 0 0 1 1 SA29 0 0 0 1 SA30 0 0 0 1 SA31 0 0 0 SA32 0 0 SA33 0 SA34 0 SA35 fo rN ew D SA11 SA12 00C0000–00CFFFF 0110000–011FFFF 0240000–025FFFF 0120000–012FFFF 128/64 0260000–027FFFF 0130000–013FFFF 128/64 0280000–029FFFF 0140000–014FFFF 1 128/64 0320000–033FFFF 0190000–019FFFF 1 0 128/64 0340000–035FFFF 01A0000–01AFFFF 0 1 1 128/64 0360000–037FFFF 01B0000–01BFFFF 1 0 0 128/64 0380000–039FFFF 01C0000–01CFFFF 1 1 0 1 128/64 03A0000–03BFFFF 01D0000–01DFFFF 1 1 1 0 128/64 03C0000–03DFFFF 01E0000–01EFFFF 1 1 1 1 1 128/64 03E0000–03FFFFF 01F0000–01FFFFF 1 0 0 0 0 0 128/64 0400000–041FFFF 0200000–020FFFF 0 1 0 0 0 0 1 128/64 0420000–043FFFF 0210000–021FFFF 0 1 0 0 0 1 0 128/64 0440000–045FFFF 0220000–022FFFF 0 0 1 0 0 0 1 1 128/64 0460000–047FFFF 0230000–023FFFF SA36 0 0 1 0 0 1 0 0 128/64 0480000–049FFFF 0240000–024FFFF SA37 0 0 1 0 0 1 0 1 128/64 04A0000–04BFFFF 0250000–025FFFF SA38 0 0 1 0 0 1 1 0 128/64 04C0000–04DFFFF 0260000–026FFFF SA39 0 0 1 0 0 1 1 1 128/64 04E0000–04FFFFF 0270000–027FFFF SA40 0 0 1 0 1 0 0 0 128/64 0500000–051FFFF 0280000–028FFFF SA41 0 0 1 0 1 0 0 1 128/64 0520000–053FFFF 0290000–029FFFF SA42 0 0 1 0 1 0 1 0 128/64 0540000–055FFFF 02A0000–02AFFFF SA43 0 0 1 0 1 0 1 1 128/64 0560000–057FFFF 02B0000–02BFFFF N ot ec 0 0 R om m en de d 0220000–023FFFF Document Number: 002-01522 Rev. *B Page 25 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL256N (Sheet 2 of 6) Sector A23–A16 Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0580000–059FFFF 02C0000–02CFFFF 0 0 1 0 1 1 0 0 128/64 SA45 0 0 1 0 1 1 0 1 128/64 05A0000–05BFFFF 02D0000–02DFFFF SA46 0 0 1 0 1 1 1 0 128/64 05C0000–05DFFFF 02E0000–02EFFFF SA47 0 0 1 0 1 1 1 1 128/64 05E0000–05FFFFF 02F0000–02FFFFF SA48 0 0 1 1 0 0 0 0 128/64 0600000–061FFFF 0300000–030FFFF SA49 0 0 1 1 0 0 0 1 128/64 0620000–063FFFF 0310000–031FFFF SA50 0 0 1 1 0 0 1 0 128/64 0640000–065FFFF 0320000–032FFFF SA51 0 0 1 1 0 0 1 1 128/64 0660000–067FFFF 0330000–033FFFF SA52 0 0 1 1 0 1 0 0 128/64 0680000–069FFFF 0340000–034FFFF SA53 0 0 1 1 0 1 0 1 128/64 06A0000–06BFFFF 0350000–035FFFF SA54 0 0 1 1 0 1 1 0 128/64 06C0000–06DFFFF 0360000–036FFFF SA55 0 0 1 1 0 1 1 1 128/64 06E0000–06FFFFF SA56 0 0 1 1 1 0 0 0 128/64 0700000–071FFFF SA57 0 0 1 1 1 0 0 1 128/64 0720000–073FFFF 0390000–039FFFF SA58 0 0 1 1 1 0 1 0 128/64 0740000–075FFFF 03A0000–03AFFFF SA59 0 0 1 1 1 0 1 1 128/64 0760000–077FFFF 03B0000–03BFFFF SA60 0 0 1 1 1 1 0 0 128/64 0780000–079FFFF 03C0000–03CFFFF SA61 0 0 1 1 1 1 0 1 128/64 SA62 0 0 1 1 1 1 1 0 128/64 SA63 0 0 1 1 1 1 1 1 128/64 SA64 0 1 0 0 0 0 0 0 128/64 SA65 0 1 0 0 0 0 SA66 0 1 0 0 0 0 SA67 0 1 0 0 0 0 SA68 0 1 0 0 0 1 SA69 0 1 0 0 0 1 SA70 0 1 0 0 0 SA71 0 1 0 0 0 SA72 0 1 0 0 1 SA73 0 1 0 0 SA74 0 1 0 0 SA75 0 1 0 SA76 0 1 0 SA77 0 1 SA78 0 1 SA79 0 SA80 es ig n SA44 fo rN ew D 0370000–037FFFF 07A0000–7BFFFF 03D0000–03DFFFF 07C0000–07DFFFF 03E0000–03EFFFF 07E0000–07FFFFF0 03F0000–03FFFFF 0800000–081FFFF 0400000–040FFFF d de om m en 0380000–038FFFF 1 128/64 0820000–083FFFF 0410000–041FFFF 1 0 128/64 0840000–085FFFF 0420000–042FFFF 1 1 128/64 0860000–087FFFF 0430000–043FFFF 0 0 128/64 0880000–089FFFF 0440000–044FFFF 1 128/64 08A0000–08BFFFF 0450000–045FFFF 1 0 128/64 08C0000–08DFFFF 0460000–046FFFF 1 1 1 128/64 08E0000–08FFFFF 0470000–047FFFF 0 0 0 128/64 0900000–091FFFF 0480000–048FFFF 1 0 0 1 128/64 0920000–093FFFF 0490000–049FFFF 1 0 1 0 128/64 0940000–095FFFF 04A0000–04AFFFF 0 1 0 1 1 128/64 0960000–097FFFF 04B0000–04BFFFF 0 1 1 0 0 128/64 0980000–099FFFF 04C0000–04CFFFF 0 0 1 1 0 1 128/64 09A0000–09BFFFF 04D0000–04DFFFF 0 0 1 1 1 0 128/64 09C0000–09DFFFF 04E0000–04EFFFF 1 0 0 1 1 1 1 128/64 09E0000–09FFFFF 04F0000–04FFFFF 0 1 0 1 0 0 0 0 128/64 0A00000–0A1FFFF 0500000–050FFFF SA81 0 1 0 1 0 0 0 1 128/64 0A20000–0A3FFFF 0510000–051FFFF SA82 0 1 0 1 0 0 1 0 128/64 0A40000–045FFFF 0520000–052FFFF SA83 0 1 0 1 0 0 1 1 128/64 0A60000–0A7FFFF 0530000–053FFFF SA84 0 1 0 1 0 1 0 0 128/64 0A80000–0A9FFFF 0540000–054FFFF SA85 0 1 0 1 0 1 0 1 128/64 0AA0000–0ABFFFF 0550000–055FFFF SA86 0 1 0 1 0 1 1 0 128/64 0AC0000–0ADFFFF 0560000–056FFFF SA87 0 1 0 1 0 1 1 1 128/64 0AE0000–AEFFFFF 0570000–057FFFF SA88 0 1 0 1 1 0 0 0 128/64 0B00000–0B1FFFF 0580000–058FFFF N ot ec 0 1 R 0 Document Number: 002-01522 Rev. *B Page 26 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL256N (Sheet 3 of 6) Sector A23–A16 Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0 1 0 1 1 0 0 1 128/64 0B20000–0B3FFFF 0590000–059FFFF SA90 0 1 0 1 1 0 1 0 128/64 0B40000–0B5FFFF 05A0000–05AFFFF SA91 0 1 0 1 1 0 1 1 128/64 0B60000–0B7FFFF 05B0000–05BFFFF SA92 0 1 0 1 1 1 0 0 128/64 0B80000–0B9FFFF 05C0000–05CFFFF SA93 0 1 0 1 1 1 0 1 128/64 0BA0000–0BBFFFF 05D0000–05DFFFF SA94 0 1 0 1 1 1 1 0 128/64 0BC0000–0BDFFFF 05E0000–05EFFFF SA95 0 1 0 1 1 1 1 1 128/64 0BE0000–0BFFFFF 05F0000–05FFFFF SA96 0 1 1 0 0 0 0 0 128/64 0C00000–0C1FFFF 0600000–060FFFF SA97 0 1 1 0 0 0 0 1 128/64 0C20000–0C3FFFF 0610000–061FFFF SA98 0 1 1 0 0 0 1 0 128/64 0C40000–0C5FFFF 0620000–062FFFF SA99 0 1 1 0 0 0 1 1 128/64 0C60000–0C7FFFF 0630000–063FFFF SA100 0 1 1 0 0 1 0 0 128/64 0C80000–0C9FFFF SA101 0 1 1 0 0 1 0 1 128/64 0CA0000–0CBFFFF 0650000–065FFFF SA102 0 1 1 0 0 1 1 0 128/64 0CC0000–0CDFFFF 0660000–066FFFF SA103 0 1 1 0 0 1 1 1 128/64 0CE0000–0CFFFFF 0670000–067FFFF SA104 0 1 1 0 1 0 0 0 128/64 0D00000–0D1FFFF 0680000–068FFFF SA105 0 1 1 0 1 0 0 1 128/64 0D20000–0D3FFFF 0690000–069FFFF SA106 0 1 1 0 1 0 1 0 128/64 SA107 0 1 1 0 1 0 1 1 128/64 SA108 0 1 1 0 1 1 0 0 128/64 SA109 0 1 1 0 1 1 0 1 128/64 SA110 0 1 1 0 1 1 SA111 0 1 1 0 1 1 SA112 0 1 1 1 0 0 SA113 0 1 1 1 0 0 SA114 0 1 1 1 0 0 SA115 0 1 1 1 0 SA116 0 1 1 1 0 SA117 0 1 1 1 SA118 0 1 1 SA119 0 1 1 SA120 0 1 SA121 0 SA122 SA123 es ig n SA89 fo rN ew D 0640000–064FFFF 0D40000–0D5FFFF 06B0000–06BFFFF 0D80000–0D9FFFF 06C0000–06CFFFF 0DA0000–0DBFFFF 06D0000–06DFFFF d de om m en 06A0000–06AFFFF 0D60000–0D7FFFF 0 128/64 0DC0000–0DDFFFF 06E0000–06EFFFF 1 1 128/64 0DE0000–0DFFFFF 06F0000–06FFFFF 0 0 128/64 0E00000–0E1FFFF 0700000–070FFFF 0 1 128/64 0E20000–0E3FFFF 0710000–071FFFF 0 128/64 0E40000–0E5FFFF 0720000–072FFFF 1 1 128/64 0E60000–0E7FFFF 0730000–073FFFF 1 0 0 128/64 0E80000–0E9FFFF 0740000–074FFFF 0 1 0 1 128/64 0EA0000–0EBFFFF 0750000–075FFFF 1 0 1 1 0 128/64 0EC0000–0EDFFFF 0760000–076FFFF 1 0 1 1 1 128/64 0EE0000–0EFFFFF 0770000–077FFFF 1 1 1 0 0 0 128/64 0F00000–0F1FFFF 0780000–078FFFF 1 1 1 1 0 0 1 128/64 0F20000–0F3FFFF 0790000–079FFFF 0 1 1 1 1 0 1 0 128/64 0F40000–0F5FFFF 07A0000–07AFFFF 0 1 1 1 1 0 1 1 128/64 0F60000–0F7FFFF 07B0000–07BFFFF SA124 0 1 1 1 1 1 0 0 128/64 0F80000–0F9FFFF 07C0000–07CFFFF SA125 0 1 1 1 1 1 0 1 128/64 0FA0000–0FBFFFF 07D0000–07DFFFF SA126 0 1 1 1 1 1 1 0 128/64 0FC0000–0FDFFFF 07E0000–07EFFFF SA127 0 1 1 1 1 1 1 1 128/64 0FE0000–0FFFFFF 07F0000–07FFFFF SA128 1 0 0 0 0 0 0 0 128/64 1000000–101FFFF 0800000–080FFFF SA129 1 0 0 0 0 0 0 1 128/64 1020000–103FFFF 0810000–081FFFF SA130 1 0 0 0 0 0 1 0 128/64 1040000–105FFFF 0820000–082FFFF SA131 1 0 0 0 0 0 1 1 128/64 1060000–107FFFF 0830000–083FFFF SA132 1 0 0 0 0 1 0 0 128/64 1080000–109FFFF 0840000–084FFFF SA133 1 0 0 0 0 1 0 1 128/64 10A0000–10BFFFF 0850000–085FFFF N ot ec 1 0 R 1 Document Number: 002-01522 Rev. *B Page 27 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL256N (Sheet 4 of 6) Sector A23–A16 Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1 0 0 0 0 1 1 0 128/64 10C0000–10DFFFF 0860000–086FFFF SA135 1 0 0 0 0 1 1 1 128/64 10E0000–10FFFFF 0870000–087FFFF SA136 1 0 0 0 1 0 0 0 128/64 1100000–111FFFF 0880000–088FFFF SA137 1 0 0 0 1 0 0 1 128/64 1120000–113FFFF 0890000–089FFFF SA138 1 0 0 0 1 0 1 0 128/64 1140000–115FFFF 08A0000–08AFFFF SA139 1 0 0 0 1 0 1 1 128/64 1160000–117FFFF 08B0000–08BFFFF SA140 1 0 0 0 1 1 0 0 128/64 1180000–119FFFF 08C0000–08CFFFF SA141 1 0 0 0 1 1 0 1 128/64 11A0000–11BFFFF 08D0000–08DFFFF SA142 1 0 0 0 1 1 1 0 128/64 11C0000–11DFFFF 08E0000–08EFFFF SA143 1 0 0 0 1 1 1 1 128/64 11E0000–11FFFFF 08F0000–08FFFFF SA144 1 0 0 1 0 0 0 0 128/64 1200000–121FFFF 0900000–090FFFF SA145 1 0 0 1 0 0 0 1 128/64 1220000–123FFFF SA146 1 0 0 1 0 0 1 0 128/64 1240000–125FFFF 0920000–092FFFF SA147 1 0 0 1 0 0 1 1 128/64 1260000–127FFFF 0930000–093FFFF SA148 1 0 0 1 0 1 0 0 128/64 1280000–129FFFF 0940000–094FFFF SA149 1 0 0 1 0 1 0 1 128/64 12A0000–12BFFFF 0950000–095FFFF SA150 1 0 0 1 0 1 1 0 128/64 12C0000–12DFFFF 0960000–096FFFF SA151 1 0 0 1 0 1 1 1 128/64 SA152 1 0 0 1 1 0 0 0 128/64 SA153 1 0 0 1 1 0 0 1 128/64 SA154 1 0 0 1 1 0 1 0 128/64 SA155 1 0 0 1 1 0 SA156 1 0 0 1 1 1 SA157 1 0 0 1 1 1 SA158 1 0 0 1 1 1 SA159 1 0 0 1 1 1 SA160 1 0 1 0 0 SA161 1 0 1 0 0 SA162 1 0 1 0 0 SA163 1 0 1 0 SA164 1 0 1 0 SA165 1 0 1 SA166 1 0 SA167 1 SA168 1 SA169 es ig n SA134 fo rN ew D 0910000–091FFFF 0970000–097FFFF 1300000–131FFFF 0980000–098FFFF om m en de d 12E0000–12FFFFF 1320000–133FFFF 0990000–099FFFF 1340000–135FFFF 09A0000–09AFFFF 1 128/64 1360000–137FFFF 09B0000–09BFFFF 0 0 128/64 1380000–139FFFF 09C0000–09CFFFF 0 1 128/64 13A0000–13BFFFF 09D0000–09DFFFF 1 0 128/64 13C0000–13DFFFF 09E0000–09EFFFF 1 128/64 13E0000–13FFFFF 09F0000–09FFFFF 0 0 128/64 1400000–141FFFF 0A00000–0A0FFFF 0 0 1 128/64 1420000–143FFFF 0A10000–0A1FFFF 0 1 0 128/64 1440000–145FFFF 0A20000–0A2FFFF 0 0 1 1 128/64 1460000–147FFFF 0A30000–0A3FFFF 0 1 0 0 128/64 1480000–149FFFF 0A40000–0A4FFFF 0 0 1 0 1 128/64 14A0000–14BFFFF 0A50000–0A5FFFF 1 0 0 1 1 0 128/64 14C0000–14DFFFF 0A60000–0A6FFFF 0 1 0 0 1 1 1 128/64 14E0000–14FFFFF 0A70000–0A7FFFF 0 1 0 1 0 0 0 128/64 1500000–151FFFF 0A80000–0A8FFFF 1 0 1 0 1 0 0 1 128/64 1520000–153FFFF 0A90000–0A9FFFF SA170 1 0 1 0 1 0 1 0 128/64 1540000–155FFFF 0AA0000–0AAFFFF SA171 1 0 1 0 1 0 1 1 128/64 1560000–157FFFF 0AB0000–0ABFFFF SA172 1 0 1 0 1 1 0 0 128/64 1580000–159FFFF 0AC0000–0ACFFFF SA173 1 0 1 0 1 1 0 1 128/64 15A0000–15BFFFF 0AD0000–0ADFFFF SA174 1 0 1 0 1 1 1 0 128/64 15C0000–15DFFFF 0AE0000–0AEFFFF SA175 1 0 1 0 1 1 1 1 128/64 15E0000–15FFFFF 0AF0000–0AFFFFF SA176 1 0 1 1 0 0 0 0 128/64 1600000–161FFFF 0B00000–0B0FFFF SA177 1 0 1 1 0 0 0 1 128/64 1620000–163FFFF 0B10000–0B1FFFF SA178 1 0 1 1 0 0 1 0 128/64 1640000–165FFFFF 0B20000–0B2FFFF N ot ec 1 0 R 1 Document Number: 002-01522 Rev. *B Page 28 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL256N (Sheet 5 of 6) Sector A23–A16 Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1660000–167FFFF 0B30000–0B3FFFF 0B40000–0B4FFFF 1 0 1 1 0 0 1 1 128/64 SA180 1 0 1 1 0 1 0 0 128/64 1680000–169FFFF SA181 1 0 1 1 0 1 0 1 128/64 16A0000–16BFFFF 0B50000–0B5FFFF SA182 1 0 1 1 0 1 1 0 128/64 16C0000–16DFFFF 0B60000–0B6FFFF SA183 1 0 1 1 0 1 1 1 128/64 16E0000–16FFFFF 0B70000–0B7FFFF SA184 1 0 1 1 1 0 0 0 128/64 1700000–171FFFF 0B80000–0B8FFFF SA185 1 0 1 1 1 0 0 1 128/64 1720000–173FFFF 0B90000–0B9FFFF SA186 1 0 1 1 1 0 1 0 128/64 1740000–175FFFF 0BA0000–0BAFFFF SA187 1 0 1 1 1 0 1 1 128/64 1760000–177FFFF 0BB0000–0BBFFFF SA188 1 0 1 1 1 1 0 0 128/64 1780000–179FFFF 0BC0000–0BCFFFF SA189 1 0 1 1 1 1 0 1 128/64 17A0000–17BFFFF 0BD0000–0BDFFFF SA190 1 0 1 1 1 1 1 0 128/64 17C0000–17DFFFF SA191 1 0 1 1 1 1 1 1 128/64 17E0000–17FFFFF 0BF0000–0BFFFFF SA192 1 1 0 0 0 0 0 0 128/64 1800000–181FFFF 0C00000–0C0FFFF SA193 1 1 0 0 0 0 0 1 128/64 1820000–183FFFF 0C10000–0C1FFFF SA194 1 1 0 0 0 0 1 0 128/64 1840000–185FFFF SA195 1 1 0 0 0 0 1 1 128/64 1860000–187FFFF 0C30000–0C3FFFF SA196 1 1 0 0 0 1 0 0 128/64 SA197 1 1 0 0 0 1 0 1 128/64 SA198 1 1 0 0 0 1 1 0 128/64 SA199 1 1 0 0 0 1 1 1 128/64 SA200 1 1 0 0 1 0 SA201 1 1 0 0 1 0 SA202 1 1 0 0 1 0 SA203 1 1 0 0 1 0 SA204 1 1 0 0 1 1 SA205 1 1 0 0 1 SA206 1 1 0 0 1 SA207 1 1 0 0 1 SA208 1 1 0 1 SA209 1 1 0 1 SA210 1 1 0 SA211 1 1 SA212 1 SA213 1 SA214 es ig n SA179 0C20000–0C2FFFF 1880000–189FFFF 0C40000–0C4FFFF 18A0000–18BFFFF 0C50000–0C5FFFF 18C0000–18DFFFF 0C60000–0C6FFFF 18E0000–18FFFFF 0C70000–0C7FFFF 0C80000–0C8FFFF om m en de d fo rN ew D 0BE0000–0BEFFFF 0 128/64 1900000–191FFFF 0 1 128/64 1920000–193FFFF 0C90000–0C9FFFF 1 0 128/64 1940000–195FFFF 0CA0000–0CAFFFF 1 1 128/64 1960000–197FFFF 0CB0000–0CBFFFF 0 128/64 1980000–199FFFF 0CC0000–0CCFFFF 0 1 128/64 19A0000–19BFFFF 0CD0000–0CDFFFF 1 1 0 128/64 19C0000–19DFFFF 0CE0000–0CEFFFF 1 1 1 128/64 19E0000–19FFFF 0CF0000–0CFFFFF 0 0 0 0 128/64 1A00000–1A1FFFF 0D00000–0D0FFFF 0 0 0 1 128/64 1A20000–1A3FFFF 0D10000–0D1FFFF 1 0 0 1 0 128/64 1A40000–1A5FFFF 0D20000–0D2FFFF 0 1 0 0 1 1 128/64 1A60000–1A7FFFF 0D30000–0D3FFFF 1 0 1 0 1 0 0 128/64 1A80000–1A9FFFF 0D40000–0D4FFFF 1 0 1 0 1 0 1 128/64 1AA0000–1ABFFFF 0D50000–0D5FFFF 1 1 0 1 0 1 1 0 128/64 1AC0000–1ADFFFF 0D60000–0D6FFFF SA215 1 1 0 1 0 1 1 1 128/64 1AE0000–1AFFFFF 0D70000–0D7FFFF SA216 1 1 0 1 1 0 0 0 128/64 1B00000–1B1FFFF 0D80000–0D8FFFF SA217 1 1 0 1 1 0 0 1 128/64 1B20000–1B3FFFF 0D90000–0D9FFFF SA218 1 1 0 1 1 0 1 0 128/64 1B40000–1B5FFFF 0DA0000–0DAFFFF SA219 1 1 0 1 1 0 1 1 128/64 1B60000–1B7FFFF 0DB0000–0DBFFFF SA220 1 1 0 1 1 1 0 0 128/64 1B80000–1B9FFFF 0DC0000–0DCFFFF SA221 1 1 0 1 1 1 0 1 128/64 1BA0000–1BBFFFF 0DD0000–0DDFFFF SA222 1 1 0 1 1 1 1 0 128/64 1BC0000–1BDFFFF 0DE0000–0DEFFFF SA223 1 1 0 1 1 1 1 1 128/64 1BE0000–1BFFFFF 0DF0000–0DFFFFF N ot ec 0 1 R 0 Document Number: 002-01522 Rev. *B Page 29 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL256N (Sheet 6 of 6) Sector A23–A16 Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 1 1 1 0 0 0 0 0 128/64 1C00000–1C1FFFF 0E00000–0E0FFFF SA225 1 1 1 0 0 0 0 1 128/64 1C20000–1C3FFFF 0E10000–0E1FFFF SA226 1 1 1 0 0 0 1 0 128/64 1C40000–1C5FFFF 0E20000–0E2FFFF SA227 1 1 1 0 0 0 1 1 128/64 1C60000–1C7FFFF 0E30000–0E3FFFF SA228 1 1 1 0 0 1 0 0 128/64 1C80000–1C9FFFF 0E40000–0E4FFFF SA229 1 1 1 0 0 1 0 1 128/64 1CA0000–1CBFFFF 0E50000–0E5FFFF SA230 1 1 1 0 0 1 1 0 128/64 1CC0000–1CDFFFF 0E60000–0E6FFFF SA231 1 1 1 0 0 1 1 1 128/64 1CE0000–1CFFFFF 0E70000–0E7FFFF SA232 1 1 1 0 1 0 0 0 128/64 1D00000–1D1FFFF 0E80000–0E8FFFF SA233 1 1 1 0 1 0 0 1 128/64 1D20000–1D3FFFF 0E90000–0E9FFFF SA234 1 1 1 0 1 0 1 0 128/64 1D40000–1D5FFFF 0EA0000–0EAFFFF SA235 1 1 1 0 1 0 1 1 128/64 1D60000–1D7FFFF SA236 1 1 1 0 1 1 0 0 128/64 1D80000–1D9FFFF 0EC0000–0ECFFFF SA237 1 1 1 0 1 1 0 1 128/64 1DA0000–1DBFFFF 0ED0000–0EDFFFF SA238 1 1 1 0 1 1 1 0 128/64 1DC0000–1DDFFFF 0EE0000–0EEFFFF SA239 1 1 1 0 1 1 1 1 128/64 1DE0000–1DFFFFF 0EF0000–0EFFFFF SA240 1 1 1 1 0 0 0 0 128/64 1E00000–1E1FFFF 0F00000–0F0FFFF SA241 1 1 1 1 0 0 0 1 128/64 SA242 1 1 1 1 0 0 1 0 128/64 SA243 1 1 1 1 0 0 1 1 128/64 SA244 1 1 1 1 0 1 0 0 128/64 SA245 1 1 1 1 0 1 SA246 1 1 1 1 0 1 SA247 1 1 1 1 0 1 SA248 1 1 1 1 1 0 SA249 1 1 1 1 1 0 SA250 1 1 1 1 1 SA251 1 1 1 1 1 SA252 1 1 1 1 1 SA253 1 1 1 1 SA254 1 1 1 1 SA255 1 1 1 1 es ig n SA224 fo rN ew D 0EB0000–0EBFFFF 0F10000–0F1FFFF 1E40000–1E5FFFF 0F20000–0F2FFFF om m en de d 1E20000–1E3FFFF 1E60000–137FFFF 0F30000–0F3FFFF 1E80000–1E9FFFF 0F40000–0F4FFFF 1 128/64 1EA0000–1EBFFFF 0F50000–0F5FFFF 1 0 128/64 1EC0000–1EDFFFF 0F60000–0F6FFFF 1 1 128/64 1EE0000–1EFFFFF 0F70000–0F7FFFF 0 0 128/64 1F00000–1F1FFFF 0F80000–0F8FFFF 1 128/64 1F20000–1F3FFFF 0F90000–0F9FFFF 1 0 128/64 1F40000–1F5FFFF 0FA0000–0FAFFFF 0 1 1 128/64 1F60000–1F7FFFF 0FB0000–0FBFFFF 1 0 0 128/64 1F80000–1F9FFFF 0FC0000–0FCFFFF 1 1 0 1 128/64 1FA0000–1FBFFFF 0FD0000–0FDFFFF 1 1 1 0 128/64 1FC0000–1FDFFFF 0FE0000–0FEFFFF 1 1 1 1 128/64 1FE0000–1FFFFFF 0FF0000–0FFFFFF N ot ec 0 0 R 0 Document Number: 002-01522 Rev. *B Page 30 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL128N (Sheet 1 of 3) Sector A22–A16 Sector Size (Kbytes/ Kwords) 8-Bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) SA0 0 0 0 0 0 0 0 128/64 0000000–001FFFF 0000000–000FFFF SA1 0 0 0 0 0 0 1 128/64 0020000–003FFFF 0010000–001FFFF SA2 0 0 0 0 0 1 0 128/64 0040000–005FFFF 0020000–002FFFF SA3 0 0 0 0 0 1 1 128/64 0060000–007FFFF 0030000–003FFFF SA4 0 0 0 0 1 0 0 128/64 0080000–009FFFF 0040000–004FFFF 0050000–005FFFF 0 0 0 0 1 0 1 128/64 00A0000–00BFFFF SA6 0 0 0 0 1 1 0 128/64 00C0000–00DFFFF 0060000–006FFFF SA7 0 0 0 0 1 1 1 128/64 00E0000–00FFFFF 0070000–007FFFF SA8 0 0 0 1 0 0 0 128/64 0100000–011FFFF 0080000–008FFFF 0 0 1 0 0 1 128/64 0120000–013FFFF 0 0 0 1 0 1 0 128/64 0140000–015FFFF 0090000–009FFFF es 0 00A0000–00AFFFF 0 0 0 1 0 1 1 128/64 0160000–017FFFF 00B0000–00BFFFF 0 0 0 1 1 0 0 128/64 0180000–019FFFF 00C0000–00CFFFF SA13 0 0 0 1 1 0 1 128/64 01A0000–01BFFFF 00D0000–00DFFFF SA14 0 0 0 1 1 1 0 128/64 01C0000–01DFFFF 00E0000–00EFFFF SA15 0 0 0 1 1 1 1 128/64 01E0000–01FFFFF 00F0000–00FFFFF SA16 0 0 1 0 0 0 0 128/64 0200000–021FFFF 0100000–010FFFF SA17 0 0 1 0 0 0 1 128/64 SA18 0 0 1 0 0 1 0 128/64 SA19 0 0 1 0 0 1 1 128/64 SA20 0 0 1 0 1 0 1 0 1 0 0 1 0 1 SA23 0 0 1 0 1 SA24 0 0 1 1 0 0 0 1 1 SA26 0 0 1 1 0 1 0 0 1 SA29 0 0 SA30 0 0 SA31 0 SA32 0 0 fo 0110000–011FFFF 0240000–025FFFF 0120000–012FFFF 0260000–027FFFF 0130000–013FFFF 0280000–029FFFF 0140000–014FFFF 0150000–015FFFF d de 128/64 0220000–023FFFF 0 1 128/64 02A0000–02BFFFF 1 0 128/64 02C0000–02DFFFF 0160000–016FFFF 1 1 128/64 02E0000–02FFFFF 0170000–017FFFF 0 0 128/64 0300000–031FFFF 0180000–018FFFF 0 1 128/64 0320000–033FFFF 0190000–019FFFF 1 0 128/64 0340000–035FFFF 01A0000–01AFFFF 1 0 1 1 128/64 0360000–037FFFF 01B0000–01BFFFF 1 1 0 0 128/64 0380000–039FFFF 01C0000–01CFFFF 1 1 1 0 1 128/64 03A0000–03BFFFF 01D0000–01DFFFF 1 1 1 1 0 128/64 03C0000–03DFFFF 01E0000–01EFFFF 0 1 1 1 1 1 128/64 03E0000–03FFFFF 01F0000–01FFFFF 0 1 0 0 0 0 0 128/64 0400000–041FFFF 0200000–020FFFF SA33 0 1 0 0 0 0 1 128/64 0420000–043FFFF 0210000–021FFFF SA34 0 1 0 0 0 1 0 128/64 0440000–045FFFF 0220000–022FFFF SA35 0 1 0 0 0 1 1 128/64 0460000–047FFFF 0230000–023FFFF SA36 0 1 0 0 1 0 0 128/64 0480000–049FFFF 0240000–024FFFF 0250000–025FFFF ot 0 SA28 N SA27 0 R SA25 om m en 0 SA22 0 ec SA21 ew SA11 SA12 rN D SA9 SA10 ig n SA5 SA37 0 1 0 0 1 0 1 128/64 04A0000–04BFFFF SA38 0 1 0 0 1 1 0 128/64 04C0000–04DFFFF 0260000–026FFFF SA39 0 1 0 0 1 1 1 128/64 04E0000–04FFFFF 0270000–027FFFF SA40 0 1 0 1 0 0 0 128/64 0500000–051FFFF 0280000–028FFFF SA41 0 1 0 1 0 0 1 128/64 0520000–053FFFF 0290000–029FFFF SA42 0 1 0 1 0 1 0 128/64 0540000–055FFFF 02A0000–02AFFFF SA43 0 1 0 1 0 1 1 128/64 0560000–057FFFF 02B0000–02BFFFF Document Number: 002-01522 Rev. *B Page 31 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL128N (Sheet 2 of 3) Sector A22–A16 Sector Size (Kbytes/ Kwords) 8-Bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0580000–059FFFF 02C0000–02CFFFF 0 1 0 1 1 0 0 128/64 SA45 0 1 0 1 1 0 1 128/64 05A0000–05BFFFF 02D0000–02DFFFF SA46 0 1 0 1 1 1 0 128/64 05C0000–05DFFFF 02E0000–02EFFFF SA47 0 1 0 1 1 1 1 128/64 05E0000–05FFFFF 02F0000–02FFFFF SA48 0 1 1 0 0 0 0 128/64 0600000–061FFFF 0300000–030FFFF SA49 0 1 1 0 0 0 1 128/64 0620000–063FFFF 0310000–031FFFF SA50 0 1 1 0 0 1 0 128/64 0640000–065FFFF 0320000–032FFFF SA51 0 1 1 0 0 1 1 128/64 0660000–067FFFF 0330000–033FFFF SA52 0 1 1 0 1 0 0 128/64 0680000–069FFFF 0340000–034FFFF 0350000–035FFFF 1 1 0 1 0 1 128/64 06A0000–06BFFFF 0 1 1 0 1 1 0 128/64 06C0000–06DFFFF SA55 0 1 1 0 1 1 1 128/64 06E0000–06FFFFF SA56 0 1 1 1 0 0 0 128/64 0700000–071FFFF es 0 SA54 0360000–036FFFF 0370000–037FFFF ew D SA53 ig n SA44 0380000–038FFFF 0 1 1 1 0 0 1 128/64 0720000–073FFFF 0390000–039FFFF SA58 0 1 1 1 0 1 0 128/64 0740000–075FFFF 03A0000–03AFFFF rN SA57 0 1 1 1 0 1 1 128/64 0760000–077FFFF 03B0000–03BFFFF SA60 0 1 1 1 1 0 0 128/64 0780000–079FFFF 03C0000–03CFFFF SA61 0 1 1 1 1 0 1 128/64 07A0000–07BFFFF 03D0000–03DFFFF SA62 0 1 1 1 1 1 0 128/64 SA63 0 1 1 1 1 1 1 SA64 1 0 0 0 0 0 SA65 1 0 0 0 0 SA66 1 0 0 0 0 SA67 1 0 0 0 0 SA68 1 0 0 0 1 d fo SA59 03E0000–03EFFFF 128/64 07E0000–07FFFFF 03F0000–03FFFFF 0 128/64 0800000–081FFFF 0400000–040FFFF 0 1 128/64 0820000–083FFFF 0410000–041FFFF 1 0 128/64 0840000–085FFFF 0420000–042FFFF 1 1 128/64 0860000–087FFFF 0430000–043FFFF 0 0 128/64 0880000–089FFFF 0440000–044FFFF 0450000–045FFFF ec om m en de 07C0000–07DFFFF 1 0 0 0 1 0 1 128/64 08A0000–08BFFFF SA70 1 0 0 0 1 1 0 128/64 08C0000–08DFFFF 0460000–046FFFF SA71 1 0 0 0 1 1 1 128/64 08E0000–08FFFFF 0470000–047FFFF SA72 1 0 0 0 0 128/64 0900000–091FFFF 0480000–048FFFF 1 0 SA74 1 0 ot 1 N SA73 R SA69 0 0 1 0 0 1 128/64 0920000–093FFFF 0490000–049FFFF 0 1 0 1 0 128/64 0940000–095FFFF 04A0000–04AFFFF SA75 1 0 0 1 0 1 1 128/64 0960000–097FFFF 04B0000–04BFFFF SA76 1 0 0 1 1 0 0 128/64 0980000–099FFFF 04C0000–04CFFFF SA77 1 0 0 1 1 0 1 128/64 09A0000–09BFFFF 04D0000–04DFFFF SA78 1 0 0 1 1 1 0 128/64 09C0000–09DFFFF 04E0000–04EFFFF SA79 1 0 0 1 1 1 1 128/64 09E0000–09FFFFF 04F0000–04FFFFF SA80 1 0 1 0 0 0 0 128/64 0A00000–0A1FFFF 0500000–050FFFF SA81 1 0 1 0 0 0 1 128/64 0A20000–0A3FFFF 0510000–051FFFF SA82 1 0 1 0 0 1 0 128/64 0A40000–0A5FFFF 0520000–052FFFF SA83 1 0 1 0 0 1 1 128/64 0A60000–0A7FFFF 0530000–053FFFF SA84 1 0 1 0 1 0 0 128/64 0A80000–0A9FFFF 0540000–054FFFF SA85 1 0 1 0 1 0 1 128/64 0AA0000–0ABFFFF 0550000–055FFFF SA86 1 0 1 0 1 1 0 128/64 0AC0000–0ADFFFF 0560000–056FFFF SA87 1 0 1 0 1 1 1 128/64 0AE0000–0AFFFFF 0570000–057FFFF Document Number: 002-01522 Rev. *B Page 32 of 92 S29GL512N S29GL256N S29GL128N Sector Address Table–S29GL128N (Sheet 3 of 3) Sector A22–A16 Sector Size (Kbytes/ Kwords) 8-Bit Address Range (in hexadecimal) 16-bit Address Range (in hexadecimal) 0580000–058FFFF SA88 1 0 1 1 0 0 0 128/64 0B00000–0B1FFFF SA89 1 0 1 1 0 0 1 128/64 0B20000–0B3FFFF 0590000–059FFFF SA90 1 0 1 1 0 1 0 128/64 0B40000–0B5FFFF 05A0000–05AFFFF SA91 1 0 1 1 0 1 1 128/64 0B60000–0B7FFFF 05B0000–05BFFFF SA92 1 0 1 1 1 0 0 128/64 0B80000–0B9FFFF 05C0000–05CFFFF 1 0 1 1 1 0 1 128/64 0BA0000–0BBFFFF 05D0000–05DFFFF SA94 1 0 1 1 1 1 0 128/64 0BC0000–0BDFFFF 05E0000–05EFFFF SA95 1 0 1 1 1 1 1 128/64 0BE0000–0BFFFFF 05F0000–05FFFFF SA96 1 1 0 0 0 0 0 128/64 0C00000–0C1FFFF 0600000–060FFFF SA97 1 1 0 0 0 0 1 128/64 0C20000–0C3FFFF 0610000–061FFFF SA98 1 1 0 0 0 1 0 128/64 0C40000–0C5FFFF SA99 1 1 0 0 0 1 1 128/64 0C60000–0C7FFFF SA100 1 1 0 0 1 0 0 128/64 0C80000–0C9FFFF es ig n SA93 0620000–062FFFF ew D 0630000–063FFFF 0640000–064FFFF 1 1 0 0 1 0 1 128/64 0CA0000–0CBFFFF 0650000–065FFFF SA102 1 1 0 0 1 1 0 128/64 0CC0000–0CDFFFF 0660000–066FFFF SA103 1 1 0 0 1 1 1 128/64 0CE0000–0CFFFFF 0670000–067FFFF SA104 1 1 0 1 0 0 0 128/64 0D00000–0D1FFFF 0680000–068FFFF SA105 1 1 0 1 0 0 1 128/64 SA106 1 1 0 1 0 1 0 128/64 fo rN SA101 0D40000–0D5FFFF 0690000–069FFFF 06A0000–06AFFFF 1 1 0 1 0 1 1 128/64 0D60000–0D7FFFF 06B0000–06BFFFF SA108 1 1 0 1 1 0 0 128/64 0D80000–0D9FFFF 06C0000–06CFFFF SA109 1 1 0 1 1 0 1 128/64 0DA0000–0DBFFFF 06D0000–06DFFFF SA110 1 1 0 1 1 1 0 128/64 0DC0000–0DDFFFF 06E0000–06EFFFF SA111 1 1 0 1 1 1 1 128/64 0DE0000–0DFFFFF 06F0000–06FFFFF SA112 1 1 1 0 0 0 0 128/64 0E00000–0E1FFFF 0700000–070FFFF SA113 1 1 1 0 0 0 1 128/64 0E20000–0E3FFFF 0710000–071FFFF SA114 1 1 1 0 0 1 0 128/64 0E40000–0E5FFFF 0720000–072FFFF SA115 1 1 1 0 0 1 1 128/64 0E60000–0E7FFFF 0730000–073FFFF SA116 1 1 1 1 0 0 128/64 0E80000–0E9FFFF 0740000–074FFFF SA117 1 1 1 0 1 0 1 128/64 0EA0000–0EBFFFF 0750000–075FFFF SA118 1 1 1 0 1 1 0 128/64 0EC0000–0EDFFFF 0760000–076FFFF SA119 1 1 1 0 1 1 1 128/64 0EE0000–0EFFFFF 0770000–077FFFF SA120 1 1 1 1 0 0 0 128/64 0F00000–0F1FFFF 0780000–078FFFF ot R om m en SA107 ec de d 0D20000–0D3FFFF N 0 SA121 1 1 1 1 0 0 1 128/64 0F20000–0F3FFFF 0790000–079FFFF SA122 1 1 1 1 0 1 0 128/64 0F40000–0F5FFFF 07A0000–07AFFFF SA123 1 1 1 1 0 1 1 128/64 0F60000–0F7FFFF 07B0000–07BFFFF SA124 1 1 1 1 1 0 0 128/64 0F80000–0F9FFFF 07C0000–07CFFFF SA125 1 1 1 1 1 0 1 128/64 0FA0000–0FBFFFF 07D0000–07DFFFF SA126 1 1 1 1 1 1 0 128/64 0FC0000–0FDFFFF 07E0000–07EFFFF SA127 1 1 1 1 1 1 1 128/64 0FE0000–0FFFFFF 07F0000–07FFFFF Document Number: 002-01522 Rev. *B Page 33 of 92 S29GL512N S29GL256N S29GL128N 7.9 Autoselect Mode The autoselect mode provides manufacturer and device identification, and sector group protection verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command register. When using programming equipment, the autoselect mode requires VID on address pin A9. Address pins A6, A3, A2, A1, and A0 must be as shown in Table . In addition, when verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table on page 13). Table on page 34 shows the remaining address bits that are don’t care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ7– DQ0. ig n To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Table on page 54 and Table on page 57. This method does not require VID. Refer to the Autoselect Command Sequence on page 44 for more information. WE# L L H X X A9 VID X A6 A5 to A4 A3 to A2 L X L Cycle 1 L H X X VID X L X H fo L Cycle 3 H L L H Cycle 3 Cycle 1 Cycle 2 L L H Cycle 3 L L Secured Silicon Sector Indicator Bit (DQ7), WP# protects highest address sector L L Secured Silicon Sector Indicator Bit (DQ7), WP# protects lowest address sector L X VID X X X VID X L L X X A0 BYTE# = VIL DQ7 to DQ0 L L 00 X 01h L H 22 X 7Eh H L 22 X 23h H H 22 X 01h L L H 22 X 7Eh H H L 22 X 22h H H H 22 X 01h L L H 22 X 7Eh H H L 22 X 21h H H H 22 X 01h X X L X L H L X X 01h (protected), 00h (unprotected) VID H X X VID X L X L H H X X 98h (factory locked), 18h (not factory locked) H X X VID X L X L H H X X 88h (factory locked), 08h (not factory locked) H SA N ot R Sector Group Protection Verification X om m en Cycle 2 de d Cycle 1 A1 rN L Cycle 2 DQ8 to DQ15 BYTE#= VIH D OE# A8 to A7 ec Device ID Device ID Device ID S29GL128N S29GL256N S29GL512N Manufacturer ID: Spansion Product CE# A14 to A10 ew Description A22t o A15 es Autoselect Codes (High Voltage Method) L Legend L = Logic Low = VIL H = Logic High = VIH SA = Sector Address X = Don’t care 7.10 Sector Protection The device features several levels of sector protection, which can disable both the program and erase operations in certain sectors or sector groups: 7.10.1 Persistent Sector Protection A command sector protection method that replaces the old 12 V controlled protection method. Document Number: 002-01522 Rev. *B Page 34 of 92 S29GL512N S29GL256N S29GL128N 7.10.2 Password Sector Protection A highly sophisticated protection method that requires a password before changes to certain sectors or sector groups are permitted 7.10.3 WP# Hardware Protection A write protect pin that can prevent program or erase operations in the outermost sectors. The WP# Hardware Protection feature is always available, independent of the software managed protection method chosen. 7.10.4 Selecting a Sector Protection Mode es ig n All parts default to operate in the Persistent Sector Protection mode. The customer must then choose if the Persistent or Password Protection method is most desirable. There are two one-time programmable non-volatile bits that define which sector protection method is used. If the customer decides to continue using the Persistent Sector Protection method, they must set the Persistent Sector Protection Mode Locking Bit. This permanently sets the part to operate only using Persistent Sector Protection. If the customer decides to use the password method, they must set the Password Mode Locking Bit. This permanently sets the part to operate only using password sector protection. rN ew D It is important to remember that setting either the Persistent Sector Protection Mode Locking Bit or the Password Mode Locking Bit permanently selects the protection mode. It is not possible to switch between the two methods once a locking bit is set. It is important that one mode is explicitly selected when the device is first programmed, rather than relying on the default mode alone. This is so that it is not possible for a system program or virus to later set the Password Mode Locking Bit, which would cause an unexpected shift from the default Persistent Sector Protection Mode into the Password Protection Mode. fo The device is shipped with all sectors unprotected. The factory offers the option of programming and protecting sectors at the factory prior to shipping the device through the ExpressFlash™ Service. Contact your sales representative for details. Advanced Sector Protection om m en 7.11 de d It is possible to determine whether a sector is protected or unprotected. See Autoselect Command Sequence on page 44 for details. Advanced Sector Protection features several levels of sector protection, which can disable both the program and erase operations in certain sectors. Persistent Sector Protection is a method that replaces the old 12V controlled protection method. Lock Register ot 7.12 R ec Password Sector Protection is a highly sophisticated protection method that requires a password before changes to certain sectors are permitted. N The Lock Register consists of 3 bits (DQ2, DQ1, and DQ0). These DQ2, DQ1, DQ0 bits of the Lock Register are programmable by the user. Users are not allowed to program both DQ2 and DQ1 bits of the Lock Register to the 00 state. If the user tries to program DQ2 and DQ1 bits of the Lock Register to the 00 state, the device aborts the Lock Register back to the default 11 state. The programming time of the Lock Register is same as the typical word programming time without utilizing the Write Buffer of the device. During a Lock Register programming sequence execution, the DQ6 Toggle Bit I toggles until the programming of the Lock Register has completed to indicate programming status. All Lock Register bits are readable to allow users to verify Lock Register statuses. The Customer Secured Silicon Sector Protection Bit is DQ0, Persistent Protection Mode Lock Bit is DQ1, and Password Protection Mode Lock Bit is DQ2 are accessible by all users. Each of these bits are non-volatile. DQ15-DQ3 are reserved and must be 1's when the user tries to program the DQ2, DQ1, and DQ0 bits of the Lock Register. The user is not required to program DQ2, DQ1 and DQ0 bits of the Lock Register at the same time. This allows users to lock the Secured Silicon Sector and then set the device either permanently into Password Protection Mode or Persistent Protection Mode and then lock the Secured Silicon Sector at separate instances and time frames.  Secured Silicon Sector Protection allows the user to lock the Secured Silicon Sector area  Persistent Protection Mode Lock Bit allows the user to set the device permanently to operate in the Persistent Protection Mode  Password Protection Mode Lock Bit allows the user to set the device permanently to operate in the Password Protection Mode Document Number: 002-01522 Rev. *B Page 35 of 92 S29GL512N S29GL256N S29GL128N Lock Register 7.13 DQ15-3 DQ2 DQ1 DQ0 Don’t Care Password Protection Mode Lock Bit Persistent Protection Mode Lock Bit Secured Silicon Sector Protection Bit Persistent Sector Protection The Persistent Sector Protection method replaces the old 12 V controlled protection method while at the same time enhancing flexibility by providing three different sector protection states:  Dynamically Locked-The sector is protected and can be changed by a simple command  Persistently Locked-A sector is protected and cannot be changed ig n  Unlocked-The sector is unprotected and can be changed by a simple command Dynamic Protection Bit (DYB) D 7.13.1 es In order to achieve these states, three types of “bits” are going to be used: rN ew A volatile protection bit is assigned for each sector. After power-up or hardware reset, the contents of all DYB bits are in the “unprotected state”. Each DYB is individually modifiable through the DYB Set Command and DYB Clear Command. When the parts are first shipped, all of the Persistent Protect Bits (PPB) are cleared into the unprotected state. The DYB bits and PPB Lock bit are defaulted to power up in the cleared state or unprotected state - meaning the all PPB bits are changeable. om m en de d fo The Protection State for each sector is determined by the logical OR of the PPB and the DYB related to that sector. For the sectors that have the PPB bits cleared, the DYB bits control whether or not the sector is protected or unprotected. By issuing the DYB Set and DYB Clear command sequences, the DYB bits is protected or unprotected, thus placing each sector in the protected or unprotected state. These are the so-called Dynamic Locked or Unlocked states. They are called dynamic states because it is very easy to switch back and forth between the protected and un-protected conditions. This allows software to easily protect sectors against inadvertent changes yet does not prevent the easy removal of protection when changes are needed. The DYB bits maybe set or cleared as often as needed. The PPB bits allow for a more static, and difficult to change, level of protection. The PPB bits retain their state across power cycles because they are Non-Volatile. Individual PPB bits are set with a program command but must all be cleared as a group through an erase command. N ot R ec The PPB Lock Bit adds an additional level of protection. Once all PPB bits are programmed to the desired settings, the PPB Lock Bit may be set to the “freeze state”. Setting the PPB Lock Bit to the “freeze state” disables all program and erase commands to the NonVolatile PPB bits. In effect, the PPB Lock Bit locks the PPB bits into their current state. The only way to clear the PPB Lock Bit to the “unfreeze state” is to go through a power cycle, or hardware reset. The Software Reset command does not clear the PPB Lock Bit to the “unfreeze state”. System boot code can determine if any changes to the PPB bits are needed e.g. to allow new system code to be downloaded. If no changes are needed then the boot code can set the PPB Lock Bit to disable any further changes to the PPB bits during system operation. The WP# write protect pin adds a final level of hardware protection. When this pin is low it is not possible to change the contents of the WP# protected sectors. These sectors generally hold system boot code. So, the WP# pin can prevent any changes to the boot code that could override the choices made while setting up sector protection during system initialization. It is possible to have sectors that have been persistently locked, and sectors that are left in the dynamic state. The sectors in the dynamic state are all unprotected. If there is a need to protect some of them, a simple DYB Set command sequence is all that is necessary. The DYB Set and DYB Clear commands for the dynamic sectors switch the DYB bits to signify protected and unprotected, respectively. If there is a need to change the status of the persistently locked sectors, a few more steps are required. First, the PPB Lock Bit must be disabled to the “unfreeze state” by either putting the device through a power-cycle, or hardware reset. The PPB bits can then be changed to reflect the desired settings. Setting the PPB Lock Bit once again to the “freeze state” locks the PPB bits, and the device operates normally again. To achieve the best protection, execute the PPB Lock Bit Set command early in the boot code, and protect the boot code by holding WP# = VIL. Document Number: 002-01522 Rev. *B Page 36 of 92 S29GL512N S29GL256N S29GL128N 7.13.2 Persistent Protection Bit (PPB) A single Persistent (non-volatile) Protection Bit is assigned to each sector. If a PPB is programmed to the protected state through the “PPB Program” command, that sector is protected from program or erase operations is read-only. If a PPB requires erasure, all of the sector PPB bits must first be erased in parallel through the “All PPB Erase” command. The “All PPB Erase” command preprograms all PPB bits prior to PPB erasing. All PPB bits erase in parallel, unlike programming where individual PPB bits are programmable. The PPB bits have the same endurance as the flash memory. 7.13.3 ig n Programming the PPB bit requires the typical word programming time without utilizing the Write Buffer. During a PPB bit programming and all PPB bit erasing sequence executions, the DQ6 Toggle Bit I toggles until the programming of the PPB bit or erasing of all PPB bits has completed to indicate programming and erasing status. Erasing all of the PPB bits at once requires typical sector erase time. During the erasing of all PPB bits, the DQ3 Sector Erase Timer bit outputs a 1 to indicate the erasure of all PPB bits are in progress. When the erasure of all PPB bits has completed, the DQ3 Sector Erase Timer bit outputs a 0 to indicate that all PPB bits have been erased. Reading the PPB Status bit requires the initial access time of the device. Persistent Protection Bit Lock (PPB Lock Bit) D es A global volatile bit. When set to the “freeze state”, the PPB bits cannot be changed. When cleared to the “unfreeze state”, the PPB bits are changeable. There is only one PPB Lock Bit per device. The PPB Lock Bit is cleared to the “unfreeze state” after power-up or hardware reset. There is no command sequence to unlock or “unfreeze” the PPB Lock Bit. rN ew Configuring the PPB Lock Bit to the freeze state requires approximately 100ns. Reading the PPB Lock Status bit requires the initial access time of the device. Sector Protection Schemes Unprotect Unprotect Freeze Unprotect Protect Unfreeze Unprotect Protect Protect Unprotect Protect Unprotect Protect Protect Protect Protect Sector State d Unfreeze Unprotected – PPB and DYB are changeable de PPB Lock Bit Unprotect om m en PPB Bit Unprotect fo Protection States DYB Bit Unprotected – PPB not changeable, DYB is changeable Protected – PPB and DYB are changeable Freeze Protected – PPB not changeable, DYB is changeable Unfreeze Protected – PPB and DYB are changeable Freeze Protected – PPB not changeable, DYB is changeable ec Unfreeze Protected – PPB and DYB are changeable Protected – PPB not changeable, DYB is changeable R Freeze N ot Table contains all possible combinations of the DYB bit, PPB bit, and PPB Lock Bit relating to the status of the sector. In summary, if the PPB bit is set, and the PPB Lock Bit is set, the sector is protected and the protection cannot be removed until the next power cycle or hardware reset clears the PPB Lock Bit to “unfreeze state”. If the PPB bit is cleared, the sector can be dynamically locked or unlocked. The DYB bit then controls whether or not the sector is protected or unprotected. If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. A program command to a protected sector enables status polling for approximately 1 µs before the device returns to read mode without having modified the contents of the protected sector. An erase command to a protected sector enables status polling for approximately 50 µs after which the device returns to read mode without having erased the protected sector. The programming of the DYB bit, PPB bit, and PPB Lock Bit for a given sector can be verified by writing a DYB Status Read, PPB Status Read, and PPB Lock Status Read commands to the device. The Autoselect Sector Protection Verification outputs the OR function of the DYB bit and PPB bit per sector basis. When the OR function of the DYB bit and PPB bit is a 1, the sector is either protected by DYB or PPB or both. When the OR function of the DYB bit and PPB bit is a 0, the sector is unprotected through both the DYB and PPB. 7.14 Persistent Protection Mode Lock Bit Like the Password Protection Mode Lock Bit, a Persistent Protection Mode Lock Bit exists to guarantee that the device remain in software sector protection. Once programmed, the Persistent Protection Mode Lock Bit prevents programming of the Password Protection Mode Lock Bit. This guarantees that a hacker could not place the device in Password Protection Mode. The Password Protection Mode Lock Bit resides in the “Lock Register”. Document Number: 002-01522 Rev. *B Page 37 of 92 S29GL512N S29GL256N S29GL128N 7.15 Password Sector Protection The Password Sector Protection method allows an even higher level of security than the Persistent Sector Protection method. There are two main differences between the Persistent Sector Protection and the Password Sector Protection methods:  When the device is first powered on, or comes out of a reset cycle, the PPB Lock Bit is set to the locked state, or the freeze state, rather than cleared to the unlocked state, or the unfreeze state.  The only means to clear and unfreeze the PPB Lock Bit is by writing a unique 64-bit Password to the device. The Password Sector Protection method is otherwise identical to the Persistent Sector Protection method. A 64-bit password is the only additional tool utilized in this method. Password and Password Protection Mode Lock Bit ew 7.16 D es ig n The password is stored in a one-time programmable (OTP) region outside of the flash memory. Once the Password Protection Mode Lock Bit is set, the password is permanently set with no means to read, program, or erase it. The password is used to clear and unfreeze the PPB Lock Bit. The Password Unlock command must be written to the flash, along with a password. The flash device internally compares the given password with the pre-programmed password. If they match, the PPB Lock Bit is cleared to the unfreezed state, and the PPB bits can be altered. If they do not match, the flash device does nothing. There is a built-in 2 µs delay for each password check after the valid 64-bit password is entered for the PPB Lock Bit to be cleared to the “unfreezed state”. This delay is intended to thwart any efforts to run a program that tries all possible combinations in order to crack the password. d fo rN In order to select the Password Sector Protection method, the customer must first program the password. The factory recommends that the password be somehow correlated to the unique Electronic Serial Number (ESN) of the particular flash device. Each ESN is different for every flash device; therefore each password should be different for every flash device. While programming in the password region, the customer may perform Password Read operations. Once the desired password is programmed in, the customer must then set the Password Protection Mode Lock Bit. This operation achieves two objectives: de 1. It permanently sets the device to operate using the Password Protection Mode. It is not possible to reverse this function. om m en 2. It also disables all further commands to the password region. All program, and read operations are ignored. 64-bit Password N 7.17 ot R ec Both of these objectives are important, and if not carefully considered, may lead to unrecoverable errors. The user must be sure that the Password Sector Protection method is desired when programming the Password Protection Mode Lock Bit. More importantly, the user must be sure that the password is correct when the Password Protection Mode Lock Bit is programmed. Due to the fact that read operations are disabled, there is no means to read what the password is afterwards. If the password is lost after programming the Password Protection Mode Lock Bit, there is no way to clear and unfreeze the PPB Lock Bit. The Password Protection Mode Lock Bit, once programmed, prevents reading the 64-bit password on the DQ bus and further password programming. The Password Protection Mode Lock Bit is not erasable. Once Password Protection Mode Lock Bit is programmed, the Persistent Protection Mode Lock Bit is disabled from programming, guaranteeing that no changes to the protection scheme are allowed. The 64-bit Password is located in its own memory space and is accessible through the use of the Password Program and Password Read commands. The password function works in conjunction with the Password Protection Mode Lock Bit, which when programmed, prevents the Password Read command from reading the contents of the password on the pins of the device. 7.18 Persistent Protection Bit Lock (PPB Lock Bit) A global volatile bit. The PPB Lock Bit is a volatile bit that reflects the state of the Password Protection Mode Lock Bit after power-up reset. If the Password Protection Mode Lock Bit is also programmed after programming the Password, the Password Unlock command must be issued to clear and unfreeze the PPB Lock Bit after a hardware reset (RESET# asserted) or a power-up reset. Successful execution of the Password Unlock command clears and unfreezes the PPB Lock Bit, allowing for sector PPB bits to be modified. Without issuing the Password Unlock command, while asserting RESET#, taking the device through a power-on reset, or issuing the PPB Lock Bit Set command sets the PPB Lock Bit to a the “freeze state”. If the Password Protection Mode Lock Bit is not programmed, the device defaults to Persistent Protection Mode. In the Persistent Protection Mode, the PPB Lock Bit is cleared to the unfreeze state after power-up or hardware reset. The PPB Lock Bit is set to the freeze state by issuing the PPB Lock Bit Set command. Once set to the freeze state the only means for clearing the PPB Lock Bit to Document Number: 002-01522 Rev. *B Page 38 of 92 S29GL512N S29GL256N S29GL128N the “unfreeze state” is by issuing a hardware or power-up reset. The Password Unlock command is ignored in Persistent Protection Mode. Reading the PPB Lock Bit requires a 200ns access time. 7.19 Secured Silicon Sector Flash Memory Region The Secured Silicon Sector feature provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The Secured Silicon Sector is 256 bytes in length, and uses a Secured Silicon Sector Indicator Bit (DQ7) to indicate whether or not the Secured Silicon Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. 000000h–000007h ExpressFlash Factory Locked ESN Factory Locked rN Customer Lockable Determined by customer ESN or determined by customer Determined by customer Unavailable d 000008h–00007Fh ESN fo Secured Silicon Sector Address Range ew The Secured Silicon sector address space in this device is allocated as follows: D es ig n The factory offers the device with the Secured Silicon Sector either customer lockable (standard shipping option) or factory locked (contact an AMD sales representative for ordering information). The customer-lockable version is shipped with the Secured Silicon Sector unprotected, allowing customers to program the sector after receiving the device. The customer-lockable version also has the Secured Silicon Sector Indicator Bit permanently set to a 0. The factory-locked version is always protected when shipped from the factory, and has the Secured Silicon Sector Indicator Bit permanently set to a 1. Thus, the Secured Silicon Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. Customer Lockable: Secured Silicon Sector NOT Programmed or Protected At the Factory ec 7.19.1 om m en de The system accesses the Secured Silicon Sector through a command sequence (see Write Protect (WP#) on page 40). After the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the addresses normally occupied by the first sector (SA0). This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending commands to sector SA0. ot R Unless otherwise specified, the device is shipped such that the customer may program and protect the 256-byte Secured Silicon sector. N The system may program the Secured Silicon Sector using the write-buffer, accelerated and/or unlock bypass methods, in addition to the standard programming command sequence. See Command Definitions on page 43. Programming and protecting the Secured Silicon Sector must be used with caution since, once protected, there is no procedure available for unprotecting the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. The Secured Silicon Sector area can be protected using one of the following procedures:  Write the three-cycle Enter Secured Silicon Sector Region command.  To verify the protect/unprotect status of the Secured Silicon Sector, follow the algorithm. Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence to return to reading and writing within the remainder of the array. Document Number: 002-01522 Rev. *B Page 39 of 92 S29GL512N S29GL256N S29GL128N 7.19.2 Factory Locked: Secured Silicon Sector Programmed and Protected At the Factory In devices with an ESN, the Secured Silicon Sector is protected when the device is shipped from the factory. The Secured Silicon Sector cannot be modified in any way. An ESN Factory Locked device has an 16-byte random ESN at addresses 000000h–000007h. Please contact your sales representative for details on ordering ESN Factory Locked devices. Customers may opt to have their code programmed by the factory through the ExpressFlash service (Express Flash Factory Locked). The devices are then shipped from the factory with the Secured Silicon Sector permanently locked. Contact your sales representative for details on using the ExpressFlash service. 7.20 Write Protect (WP#) ig n The Write Protect function provides a hardware method of protecting the first or last sector group without using VID. Write Protect is one of two functions provided by the WP#/ACC input. ew D es If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the first or last sector group independently of whether those sector groups were protected or unprotected using the method described inAdvanced Sector Protection on page 35. Note that if WP#/ACC is at VIL when the device is in the standby mode, the maximum input load current is increased. See the table in DC Characteristics on page 65. Hardware Data Protection fo 7.21 rN If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was previously set to be protected or unprotected. Note that WP# has an internal pull-up; when unconnected, WP# is at VIH. 7.21.1 om m en de d The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes (refer to Table on page 54 and Table on page 57 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. Low VCC Write Inhibit Write Pulse Glitch Protection N 7.21.2 ot R ec When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO. Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. 7.21.3 Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. 7.21.4 Power-Up Write Inhibit If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. 8. Common Flash Memory Interface (CFI) The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device- Document Number: 002-01522 Rev. *B Page 40 of 92 S29GL512N S29GL256N S29GL128N independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any time the device is ready to read array data. The system can read CFI information at the addresses given in Table , Table on page 41, and Table on page 42. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Table , Table , Table , and Table on page 42. The system must write the reset command to return the device to reading array data. For further information, please refer to the CFI Specification and CFI Publication 100, available via the World Wide Web at http:// www.amd.com/flash/cfi. Alternatively, contact your sales representative for copies of these documents. CFI Query Identification String Addresses (x8) Data Description 10h 11h 12h 20h 22h 24h 0051h 0052h 0059h Query Unique ASCII string “QRY” 13h 14h 26h 28h 0002h 0000h Primary OEM Command Set 15h 16h 2Ah 2Ch 0040h 0000h Address for Primary Extended Table 17h 18h 2Eh 30h 0000h 0000h Alternate OEM Command Set (00h = none exists) 19h 1Ah 32h 34h 0000h 0000h Address for Alternate OEM Extended Table (00h = none exists) d fo rN ew D es ig n Addresses (x16) Addresses (x8) Data Description 1Bh 36h 0027h 1Ch 38h 0036h 1Dh 3Ah 0000h 1Eh 3Ch 0000h 1Fh 3Eh 0007h 20h 40h 0007h Typical timeout for Min. size buffer write 2N µs (00h = not supported) 21h 42h 000Ah Typical timeout per individual block erase 2N ms 22h 44h 0000h Typical timeout for full chip erase 2N ms (00h = not supported) 23h 46h 0003h Max. timeout for byte/word write 2N times typical 24h 48h 0005h Max. timeout for buffer write 2N times typical 25h 4Ah 0004h Max. timeout per individual block erase 2N times typical 26h 4Ch 0000h Max. timeout for full chip erase 2N times typical (00h = not supported) om m en Addresses (x16) R de System Interface String VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt VPP Min. voltage (00h = no VPP pin present) N ot ec VPP Max. voltage (00h = no VPP pin present) Document Number: 002-01522 Rev. *B Typical timeout per single byte/word write 2N µs Page 41 of 92 S29GL512N S29GL256N S29GL128N Device Geometry Definition Addresses (x8) Data 27h 4Eh 001Ah 0019h 0018h Description 28h 29h 50h 52h 0002h 0000h Flash Device Interface description (refer to CFI publication 100) 2Ah 2Bh 54h 56h 0005h 0000h Max. number of byte in multi-byte write = 2N (00h = not supported) 2Ch 58h 0001h Number of Erase Block Regions within device (01h = uniform device, 02h = boot device) 2Dh 2Eh 2Fh 30h 5Ah 5Ch 5Eh 60h 00xxh 000xh 0000h 000xh Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 00FFh, 001h, 0000h, 0002h = 512 Mb 00FFh, 0000h, 0000h, 0002h = 256 Mb 007Fh, 0000h, 0000h, 0002h = 128 Mb 31h 32h 33h 34h 62h 64h 66h 68h 0000h 0000h 0000h 0000h Erase Block Region 2 Information (refer to CFI publication 100) 35h 36h 37h 38h 6Ah 6Ch 6Eh 70h 0000h 0000h 0000h 0000h Erase Block Region 3 Information (refer to CFI publication 100) 39h 3Ah 3Bh 3Ch 72h 74h 76h 78h 0000h 0000h 0000h 0000h Erase Block Region 4 Information (refer to CFI publication 100) Device Size = 2N byte Data 80h 82h 84h 0050h 0052h 0049h 43h 86h 0031h 44h 88h 0033h 45h 8Ah es D ew rN fo d Description Query-unique ASCII string “PRI” Major version number, ASCII Minor version number, ASCII R ec Addresses (x8) 40h 41h 42h om m en Primary Vendor-Specific Extended Query Addresses (x16) ig n 1A = 512 Mb, 19 = 256 Mb, 18 = 128 Mb de Addresses (x16) ot 0010h Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Process Technology (Bits 7-2) 0100b = 110 nm MirrorBit 0002h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 8Eh 0001h Sector Protect 0 = Not Supported, X = Number of sectors in per group 48h 90h 0000h Sector Temporary Unprotect 00 = Not Supported, 01 = Supported 49h 92h 0008h Sector Protect/Unprotect scheme 0008h = Advanced Sector Protection 4Ah 94h 0000h Simultaneous Operation 00 = Not Supported, X = Number of Sectors in Bank 4Bh 96h 0000h Burst Mode Type 00 = Not Supported, 01 = Supported 4Ch 98h 0002h Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page 4Dh 9Ah 00B5h 4Eh 9Ch 00C5h 8Ch 47h N 46h Document Number: 002-01522 Rev. *B ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Page 42 of 92 S29GL512N S29GL256N S29GL128N Primary Vendor-Specific Extended Query Addresses (x16) Addresses (x8) Data Description WP# Protection 9. 4Fh 9Eh 00xxh 50h A0h 0001h 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top WP# protect Program Suspend 00h = Not Supported, 01h = Supported Command Definitions ig n Writing specific address and data commands or sequences into the command register initiates device operations. Table on page 54 and Table on page 57 define the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is then required to return the device to reading array data. 9.1 ew D es All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE#, whichever happens first. Refer to the AC Characteristics section for timing diagrams. Reading Array Data rN The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. de d fo After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after which the system can read data from any non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See the Erase Suspend/Erase Resume Commands section for more information. om m en The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See the next section, Reset Command, for more information. Reset Command R 9.2 ec See also Requirements for Reading Array Data on page 10 for more information. The Read-Only Operations subsection in the AC Characteristics on page 68 section provides the read parameters, and Figure 15.1 on page 68 shows the timing diagram. N ot Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to the read mode. If the program command sequence is written while the device is in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the read mode (or erasesuspend-read mode if the device was in Erase Suspend). Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the Write-to-Buffer-Abort Reset command sequence to reset the device for the next operation. Document Number: 002-01522 Rev. *B Page 43 of 92 S29GL512N S29GL256N S29GL128N 9.3 Autoselect Command Sequence The autoselect command sequence allows the host system to access the manufacturer and device codes, and determine whether or not a sector is protected. Table on page 54 and Table on page 57 show the address and data requirements. This method is an alternative to that shown in Table on page 34, which is intended for PROM programmers and requires VID on address pin A9. The autoselect command sequence may be written to an address that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The system may read at any address any number of times without initiating another autoselect command sequence:  A read cycle at address XX00h returns the manufacturer code.  Three read cycles at addresses 01h, 0Eh, and 0Fh return the device code. ig n  A read cycle to an address containing a sector address (SA), and the address 02h on A7–A0 in word mode returns 01h if the sector is protected, or 00h if it is unprotected. ew Enter Secured Silicon Sector/Exit Secured Silicon Sector Command Sequence rN 9.4 D es The system must write the reset command to return to the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend). 9.5 om m en de d fo The Secured Silicon Sector region provides a secured data area containing an 8-word/16-byte random Electronic Serial Number (ESN). The system can access the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured Silicon Sector command sequence. The Exit Secured Silicon Sector command sequence returns the device to normal operation. Table on page 54 shows the address and data requirements for both command sequences. See also “Secured Silicon Sector Flash Memory Region” for further information. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled. Word Program Command Sequence ot R ec Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Table on page 54 and Table on page 57 show the address and data requirements for the word program command sequence. N When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming is allowed in any sequence of address locations and across sector boundaries. Programming to the same word address multiple times without intervening erases (incremental bit programming) is permitted. Word programming is supported for backward compatibility with existing Flash driver software and for occasional writing of individual words. Use of Write Buffer Programming is strongly recommended for general programming use when more than a few words are to be programmed. The effective word programming time using Write Buffer Programming is much shorter than the single word programming time. Any bit cannot be programmed from 0 back to a 1. Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read shows that the data is still 0. Only erase operations can convert a 0 to a 1. Document Number: 002-01522 Rev. *B Page 44 of 92 S29GL512N S29GL256N S29GL128N 9.5.1 Unlock Bypass Command Sequence The unlock bypass feature allows the system to program words to the device faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Table on page 54 and Table on page 57 show the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. (See Table on page 54 and Table on page 57). Write Buffer Programming ig n 9.5.2 rN ew D es Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming occurs. The fourth cycle writes the sector address and the number of word locations, minus one, to be programmed. For example, if the system programs six unique address locations, then 05h should be written to the device. This tells the device how many write buffer addresses are loaded with data and therefore when to expect the Program Buffer to Flash command. The number of locations to program cannot exceed the size of the write buffer or the operation aborts. fo The fifth cycle writes the first address location and data to be programmed. The write-buffer-page is selected by address bits AMAX– A4. All subsequent address/data pairs must fall within the selected-write-buffer-page. The system then writes the remaining address/ data pairs into the write buffer. Write buffer locations may be loaded in any order. om m en de d The write-buffer-page address must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple write-buffer pages. This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected write-buffer page, the operation aborts.) ec Note that if a Write Buffer address location is loaded multiple times, the address/data pair counter is decremented for every data load operation. The host system must therefore account for loading a write-buffer location more than once. The counter decrements for each data load operation, not for each unique write-buffer-address location. Note also that if an address location is loaded more than once into the buffer, the final data loaded for that address is programmed. ot R Once the specified number of write buffer locations have been loaded, the system must then write the Program Buffer to Flash command at the sector address. Any other address and data combination aborts the Write Buffer Programming operation. The device then begins programming. Data polling should be used while monitoring the last address location loaded into the write buffer. DQ7, DQ6, DQ5, and DQ1 should be monitored to determine the device status during Write Buffer Programming. N The write-buffer programming operation can be suspended using the standard program suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device is ready to execute the next command. The Write Buffer Programming Sequence can be aborted in the following ways:  Load a value that is greater than the page buffer size during the Number of Locations to Program step.  Write to an address in a sector different than the one specified during the Write-Buffer-Load command.  Write an Address/Data pair to a different write-buffer-page than the one selected by the Starting Address during the write buffer data loading stage of the operation.  Write data other than the Confirm Command after the specified number of data load cycles. The abort condition is indicated by DQ1 = 1, DQ7 = DATA# (for the last address location loaded), DQ6 = toggle, and DQ5=0. A Write-to-Buffer-Abort Reset command sequence must be written to reset the device for the next operation. Write buffer programming is allowed in any sequence. Note that the Secured Silicon sector, autoselect, and CFI functions are unavailable when a program operation is in progress. This flash device is capable of handling multiple write buffer programming operations on the same write buffer address range without intervening erases. Any bit in a write buffer address range cannot be programmed from 0 back to a 1. Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits Document Number: 002-01522 Rev. *B Page 45 of 92 S29GL512N S29GL256N S29GL128N to indicate the operation was successful. However, a succeeding read shows that the data is still 0. Only erase operations can convert a 0 to a 1. 9.5.3 Accelerated Program The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. WP# has an internal pullup; when unconnected, WP# is at VIH. N ot R ec om m en de d fo rN ew D es ig n Figure 9.2 on page 48 illustrates the algorithm for the program operation. Refer to Erase and Program Operations on page 71 for parameters, and Figure 15.4 on page 72 for timing diagrams. Document Number: 002-01522 Rev. *B Page 46 of 92 S29GL512N S29GL256N S29GL128N Figure 9.1 Write Buffer Programming Operation Write “Write to Buffer” command and Sector Address Part of “Write to Buffer” Command Sequence Write number of addresses to program minus 1(WC) and Sector Address Write first address/data Yes ig n WC = 0 ? No Write to a different sector address es Yes Write to buffer ABORTED. Must write “Write-to-buffer Abort Reset” command sequence to return to read mode. D Abort Write to Buffer Operation? No Write next address/data pair ew (Note 1) fo de d Write program buffer to flash sector address rN WC = WC - 1 om m en Read DQ15 - DQ0 at Last Loaded Address ec DQ7 = Data? No No DQ1 = 1? DQ5 = 1? ot R No Yes Yes N Yes Read DQ15 - DQ0 with address = Last Loaded Address (Note 2) DQ7 = Data? Yes No (Note 3) FAIL or ABORT PASS Notes 1. When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address locations with data, all addresses must fall within the selected Write-Buffer Page. 2. DQ7 may change simultaneously with DQ5. Therefore, DQ7 should be verified. 3. If this flowchart location was reached because DQ5= 1, then the device FAILED. If this flowchart location was reached because DQ1= 1, then the Write to Buffer operation was ABORTED. In either case, the proper reset command must be written before the device can begin another operation. If DQ1=1, write the Write-BufferProgramming-Abort-Reset command. if DQ5=1, write the Reset command. 4. See Table on page 54 and Table on page 57 for command sequences required for write buffer programming. Document Number: 002-01522 Rev. *B Page 47 of 92 S29GL512N S29GL256N S29GL128N Figure 9.2 Program Operation START Write Program Command Sequence Embedded Program algorithm in progress Verify Data? No es Last Address? rN Increment Address D ew Yes No ig n Data Poll from System Programming Completed de d fo Yes 9.6 om m en Note See Table on page 54 and Table on page 57 for program command sequence. Program Suspend/Program Resume Command Sequence R ec The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer programming operation so that data can be read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15 µs maximum (5µs typical) and updates the status bits. Addresses are not required when writing the Program Suspend command. N ot After the programming operation is suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area (One-time Program area), then user must use the proper command sequences to enter and exit this region. Note that the Secured Silicon Sector autoselect, and CFI functions are unavailable when program operation is in progress. The system may also write the autoselect command sequence when the device is in the Program Suspend mode. The system can read as many autoselect codes as required. When the device exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See Autoselect Command Sequence on page 44 for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See Write Operation Status on page 59 for more information. The system must write the Program Resume command (address bits are don’t care) to exit the Program Suspend mode and continue the programming operation. Further writes of the Resume command are ignored. Another Program Suspend command can be written after the device has resume programming. Document Number: 002-01522 Rev. *B Page 48 of 92 S29GL512N S29GL256N S29GL128N Figure 9.3 Program Suspend/Program Resume Program Operation or Write-to-Buffer Sequence in Progress Write Program Suspend Command Sequence Write address/data XXXh/B0h Command is also valid for Erase-suspended-program operations Wait 15 μs Autoselect and SecSi Sector read operations are also allowed ig n Read data as required D es Data cannot be read from erase- or program-suspended sectors ew Done reading? No rN Yes Write Program Resume Command Sequence de d fo Write address/data XXXh/30h 9.7 om m en Device reverts to operation prior to Program Suspend Chip Erase Command Sequence N ot R ec Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table on page 54 and Table on page 57 show the address and data requirements for the chip erase command sequence. When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, or DQ2. Refer to Write Operation Status on page 59 for information on these status bits. Any commands written during the chip erase operation are ignored, including erase suspend commands. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. Figure 9.4 on page 50 illustrates the algorithm for the erase operation. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable when an erase operation in is progress. Refer to Erase and Program Operations on page 71 for parameters, and Figure 15.6 on page 73 for timing diagrams. Document Number: 002-01522 Rev. *B Page 49 of 92 S29GL512N S29GL256N S29GL128N 9.8 Sector Erase Command Sequence Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Table on page 54 and Table on page 57 shows the address and data requirements for the sector erase command sequence. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. D es ig n After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise erasure may begin. Any sector erase address and command following the exceeded time-out may or may not be accepted. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. Any command other than Sector Erase or Erase Suspend during the time-out period resets the device to the read mode. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable when an erase operation in is progress. The system must rewrite the command sequence and any additional addresses and commands. ew The system can monitor DQ3 to determine if the sector erase timer has timed out (See DQ3: Sector Erase Timer on page 63.). The time-out begins from the rising edge of the final WE# pulse in the command sequence. fo rN When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7, DQ6, or DQ2 in the erasing sector. Refer to the Write Operation Status section for information on these status bits. de d Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. om m en Figure 9.4 illustrates the algorithm for the erase operation. Refer to Erase and Program Operations on page 71 for parameters, and Figure 15.6 on page 73 for timing diagrams. ec Figure 9.4 Erase Operation R START N ot Write Erase Command Sequence (Notes 1, 2) Data Poll to Erasing Bank from System Embedded Erase algorithm in progress No Data = FFh? Yes Erasure Completed Notes 1. See Table on page 54 and Table on page 57 for program command sequence. 2. See the section on DQ3 for information on the sector erase timer. Document Number: 002-01522 Rev. *B Page 50 of 92 S29GL512N S29GL256N S29GL128N 9.9 Erase Suspend/Erase Resume Commands The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a typical of 5 smaximum of 20 s) to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. ig n After the erase operation is suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device erase suspends all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to the Write Operation Status section for information on these status bits. es After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard word program operation. Refer to Write Operation Status on page 59 for more information. ew D In the erase-suspend-read mode, the system can also issue the autoselect command sequence. Refer to the Autoselect Mode on page 34 section and Autoselect Command Sequence on page 44 for details. Lock Register Command Set Definitions de 9.10 d fo rN To resume the sector erase operation, the system must write the Erase Resume command. The address of the erase-suspended sector is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. It is important to allow an interval of at least 5 ms between Erase Resume and Erase Suspend. om m en The Lock Register Command Set permits the user to one-time program the Secured Silicon Sector Protection Bit, Persistent Protection Mode Lock Bit, and Password Protection Mode Lock Bit. The Lock Register bits are all readable after an initial access delay. The Lock Register Command Set Entry command sequence must be issued prior to any of the following commands listed, to enable proper command execution. ec Note that issuing the Lock Register Command Set Entry command disables reads and writes for the flash memory. R  Lock Register Program Command ot  Lock Register Read Command N The Lock Register Command Set Exit command must be issued after the execution of the commands to reset the device to read mode. Otherwise the device hangs. If this happens, the flash device must be reset. Please refer to RESET# for more information. It is important to note that the device is in either Persistent Protection mode or Password Protection mode depending on the mode selected prior to the device hang. For either the Secured Silicon Sector to be locked, or the device to be permanently set to the Persistent Protection Mode or the Password Protection Mode, the associated Lock Register bits must be programmed. Note that only the Persistent Protection Mode Lock Bit or the Password Protection Mode Lock Bit can be programmed. The Lock Register Program operation aborts if there is an attempt to program both the Persistent Protection Mode and the Password Protection Mode Lock bits. The Lock Register Command Set Exit command must be initiated to re-enable reads and writes to the main memory. Document Number: 002-01522 Rev. *B Page 51 of 92 S29GL512N S29GL256N S29GL128N 9.11 Password Protection Command Set Definitions The Password Protection Command Set permits the user to program the 64-bit password, verify the programming of the 64-bit password, and then later unlock the device by issuing the valid 64-bit password. The Password Protection Command Set Entry command sequence must be issued prior to any of the commands listed following to enable proper command execution. Note that issuing the Password Protection Command Set Entry command disabled reads and writes the main memory.  Password Program Command  Password Read Command  Password Unlock Command ig n The Password Program command permits programming the password that is used as part of the hardware protection scheme. The actual password is 64-bits long. There is no special addressing order required for programming the password. The password is programmed in 8-bit or 16-bit portions. Each portion requires a Password Program Command. ew D es Once the Password is written and verified, the Password Protection Mode Lock Bit in the Lock Register must be programmed in order to prevent verification. The Password Program command is only capable of programming 0s. Programming a 1 after a cell is programmed as a 0 results in a time-out by the Embedded Program AlgorithmTM with the cell remaining as a 0. The password is all F’s when shipped from the factory. All 64-bit password combinations are valid as a password. rN The Password Read command is used to verify the Password. The Password is verifiable only when the Password Protection Mode Lock Bit in the Lock Register is not programmed. If the Password Protection Mode Lock Bit in the Lock Register is programmed and the user attempts to read the Password, the device always drives all F’s onto the DQ data bus. d fo The lower two address bits (A1–A0) for word mode and (A1–A-1) for by byte mode are valid during the Password Read, Password Program, and Password Unlock commands. Writing a 1 to any other address bits (AMAX-A2) aborts the Password Read and Password Program commands. om m en de The Password Unlock command is used to clear the PPB Lock Bit to the unfreeze state so that the PPB bits can be modified. The exact password must be entered in order for the unlocking function to occur. This 64-bit Password Unlock command sequence takes at least 2 µs to process each time to prevent a hacker from running through the all 64-bit combinations in an attempt to correctly match the password. If another password unlock is issued before the 64-bit password check execution window is completed, the command is ignored. If the wrong address or data is given during password unlock command cycle, the device may enter the writeto-buffer abort state. In order to exit the write-to-abort state, the write-to-buffer-abort-reset command must be given. Otherwise the device hangs. N ot R ec The Password Unlock function is accomplished by writing Password Unlock command and data to the device to perform the clearing of the PPB Lock Bit to the unfreeze state. The password is 64 bits long. A1 and A0 are used for matching in word mode and A1, A0, A-1 in byte mode. Writing the Password Unlock command does not need to be address order specific. An example sequence is starting with the lower address A1-A0=00, followed by A1-A0=01, A1-A0=10, and A1-A0=11 if the device is configured to operate in word mode. Approximately 2 µs is required for unlocking the device after the valid 64-bit password is given to the device. It is the responsibility of the microprocessor to keep track of the entering the portions of the 64-bit password with the Password Unlock command, the order, and when to read the PPB Lock bit to confirm successful password unlock. In order to re-lock the device into the Password Protection Mode, the PPB Lock Bit Set command can be re-issued. Note: The Password Protection Command Set Exit command must be issued after the execution of the commands listed previously to reset the device to read mode. Otherwise the device hangs. Note: Issuing the Password Protection Command Set Exit command re-enables reads and writes for the main memory. 9.12 Non-Volatile Sector Protection Command Set Definitions The Non-Volatile Sector Protection Command Set permits the user to program the Persistent Protection Bits (PPB bits), erase all of the Persistent Protection Bits (PPB bits), and read the logic state of the Persistent Protection Bits (PPB bits). The Non-Volatile Sector Protection Command Set Entry command sequence must be issued prior to any of the commands listed following to enable proper command execution. Document Number: 002-01522 Rev. *B Page 52 of 92 S29GL512N S29GL256N S29GL128N Note that issuing the Non-Volatile Sector Protection Command Set Entry command disables reads and writes for the main memory.  PPB Program Command The PPB Program command is used to program, or set, a given PPB bit. Each PPB bit is individually programmed (but is bulk erased with the other PPB bits). The specific sector address (A24-A16 for S29GL512N, A23-A16 for S29GL256N, A22-A16 for S29GL128N) is written at the same time as the program command. If the PPB Lock Bit is set to the freeze state, the PPB Program command does not execute and the command times-out without programming the PPB bit.  All PPB Erase Command The All PPB Erase command is used to erase all PPB bits in bulk. There is no means for individually erasing a specific PPB bit. Unlike the PPB program, no specific sector address is required. However, when the All PPB Erase command is issued, all Sector PPB bits are erased in parallel. If the PPB Lock Bit is set to freeze state, the ALL PPB Erase command does not execute and the command times-out without erasing the PPB bits. ig n The device preprograms all PPB bits prior to erasing when issuing the All PPB Erase command. Also note that the total number of PPB program/erase cycles has the same endurance as the flash memory array. es  PPB Status Read Command ew D The programming state of the PPB for a given sector can be verified by writing a PPB Status Read Command to the device. This requires an initial access time latency. rN The Non-Volatile Sector Protection Command Set Exit command must be issued after the execution of the commands listed previously to reset the device to read mode. Global Volatile Sector Protection Freeze Command Set de 9.13 d fo Note that issuing the Non-Volatile Sector Protection Command Set Exit command re-enables reads and writes for the main memory. om m en The Global Volatile Sector Protection Freeze Command Set permits the user to set the PPB Lock Bit and reading the logic state of the PPB Lock Bit. The Global Volatile Sector Protection Freeze Command Set Entry command sequence must be issued prior to any of the commands listed following to enable proper command execution. ec Reads and writes from the main memory are not allowed.  PPB Lock Bit Set Command N ot R The PPB Lock Bit Set command is used to set the PPB Lock Bit to the freeze state if it is cleared either at reset or if the Password Unlock command was successfully executed. There is no PPB Lock Bit Clear command. Once the PPB Lock Bit is set to the freeze state, it cannot be cleared unless the device is taken through a power-on clear (for Persistent Protection Mode) or the Password Unlock command is executed (for Password Protection Mode). If the Password Protection Mode Lock Bit is programmed, the PPB Lock Bit status is reflected as set to the freeze state, even after a power-on reset cycle.  PPB Lock Bit Status Read Command The programming state of the PPB Lock Bit can be verified by executing a PPB Lock Bit Status Read command to the device. The Global Volatile Sector Protection Freeze Command Set Exit command must be issued after the execution of the commands listed previously to reset the device to read mode. 9.14 Volatile Sector Protection Command Set The Volatile Sector Protection Command Set permits the user to set the Dynamic Protection Bit (DYB) to the protected state, clear the Dynamic Protection Bit (DYB) to the unprotected state, and read the logic state of the Dynamic Protection Bit (DYB). The Volatile Sector Protection Command Set Entry command sequence must be issued prior to any of the commands listed following to enable proper command execution. Note that issuing the Volatile Sector Protection Command Set Entry command disables reads and writes from main memory.  DYB Set Command Document Number: 002-01522 Rev. *B Page 53 of 92 S29GL512N S29GL256N S29GL128N  DYB Clear Command The DYB Set and DYB Clear commands are used to protect or unprotect a given sector. The high order address bits are issued at the same time as the code 00h or 01h on DQ7-DQ0. All other DQ data bus pins are ignored during the data write cycle. The DYB bits are modifiable at any time, regardless of the state of the PPB bit or PPB Lock Bit. The DYB bits are cleared to the unprotected state at power-up or hardware reset.  DYB Status Read Command The programming state of the DYB bit for a given sector can be verified by writing a DYB Status Read command to the device. This requires an initial access delay. The Volatile Sector Protection Command Set Exit command must be issued after the execution of the commands listed previously to reset the device to read mode. Secured Silicon Sector Entry Command es 9.15 ig n Note that issuing the Volatile Sector Protection Command Set Exit command re-enables reads and writes to the main memory. D The Secured Silicon Sector Entry command allows the following commands to be executed ew  Read from Secured Silicon Sector  Program to Secured Silicon Sector fo rN Once the Secured Silicon Sector Entry Command is issued, the Secured Silicon Sector Exit command has to be issued to exit Secured Silicon Sector Mode. Secured Silicon Sector Exit Command d 9.16 9.17 om m en de The Secured Silicon Sector Exit command may be issued to exit the Secured Silicon Sector Mode. Command Definitions 1 ot Asynchronous Read (6) 1 Autoselect Manufacturer ID N Reset (7) First Bus Cycles (Notes 1–5) Second Addr Data RA RD XXX F0 R Command Sequence (Notes) ec Cycles Memory Array Commands (x16) Addr Data Third Addr Fourth Data Addr Fifth Data 4 555 AA 2AA 55 555 90 X00 01 Device ID (8) 6 555 AA 2AA 55 555 90 X01 227E Sector Protect Verify (9) 4 555 AA 2AA 55 555 90 [SA]X02 Data Secure Device Verify (10)) 4 555 AA 2AA 55 555 90 X03 Data Sixth Addr Data Addr Data X0E Data X0F Data 1 55 98 Program 4 555 AA 2AA 55 555 A0 PA PD Write to Buffer (12) 6 555 AA 2AA 55 PA 25 SA WC PA PD WBL PD Program Buffer to Flash 1 SA 29 Write to Buffer Abort Reset (13) 555 AA 2AA 55 555 10 Unlock Bypass Mode CFI Query (11) 3 555 AA 2AA 55 555 F0 Entry 3 555 AA 2AA 55 555 20 Program (14) 2 XXX A0 PA PD Sector Erase (14) 2 XXX 80 SA 30 Chip Erase (14) 2 XXX 80 SA 10 Reset 2 XXX 90 XXX 00 6 555 AA 2AA 55 555 80 Chip Erase Document Number: 002-01522 Rev. *B Page 54 of 92 S29GL512N S29GL256N S29GL128N Memory Array Commands (x16) Cycles Bus Cycles (Notes 1–5) Command Sequence (Notes) First Second Fifth Sixth Addr Data Addr Data Addr Data Addr Data Addr Data 2AA 55 555 80 555 AA 2AA 55 SA 30 6 555 AA Erase/Program Suspend (15) 1 XXX B0 XXX 30 3 555 AA 2AA 55 555 88 2AA 55 555 A0 PA PD 2AA 55 555 90 XXX 00 Program (17) 4 555 AA Read (17) 1 00 Data Exit (17) 4 555 AA ew D Legend X = Don’t care. RA = Read Address. RD = Read Data. PA = Program Address. Addresses latch on the falling edge of WE# or CE# pulse, whichever occurs later. PD = Program Data. Data latches on the rising edge of WE# or CE# pulse, whichever occurs first. SA = Sector Address. Any address that falls within a specified sector. See Tables – for sector address ranges. WBL = Write Buffer Location. Address must be within the same write buffer page as PA. WC = Word Count. Number of write buffer locations to load minus 1. ig n 1 Entry es Secured Silicon Sector Fourth Data Sector Erase Erase/Program Resume (16) Third Addr N ot R ec om m en de d fo rN Notes 1. See Table on page 10 for description of bus operations. 2. All values are in hexadecimal. 3. Shaded cells indicate read cycles. 4. Address and data bits not specified in table, legend, or notes are don’t cares (each hex digit implies 4 bits of data). 5. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return reading array data. 6. No unlock or command cycles required when bank is reading array data. 7. Reset command is required to return to reading array data in certain cases. See Reset Command on page 43 for details. 8. Data in cycles 5 and 6 are listed in Table on page 34. 9. The data is 00h for an unprotected sector and 01h for a protected sector. PPB Status Read provides the same data but in inverted form. 10. If DQ7 = 1, region is factory serialized and protected. If DQ7 = 0, region is unserialized and unprotected when shipped from factory. See Secured Silicon Sector Flash Memory Region on page 39 for more information. 11. Command is valid when device is ready to read array data or when device is in autoselect mode. 12. Total number of cycles in the command sequence is determined by the number of words written to the write buffer. 13. Command sequence resets device for next command after write-to-buffer operation. 14. Requires Entry command sequence prior to execution. Unlock Bypass Reset command is required to return to reading array data. 15. System may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 16. Erase Resume command is valid only during the Erase Suspend mode. 17. Requires Entry command sequence prior to execution. Secured Silicon Sector Exit Reset command is required to exit this mode; device may otherwise be placed in an unknown state. Document Number: 002-01522 Rev. *B Page 55 of 92 S29GL512N S29GL256N S29GL128N Sector Protection Commands (x16) Cycles Bus Cycles (Notes 1–4) Command Sequence (Notes) Volatile Sector Protection (DYB) Addr Fourth Data Addr Data 555 40 555 60 Fifth Addr Data 3 555 AA 2AA 55 Program (6) 2 XX A0 XXX Data Read (6) 1 00 Data Command Set Exit (7) 2 XX 90 XX 00 Command Set Entry (5) 3 555 AA 2AA 55 Program (8) 2 XX A0 PWAx PWDx Read (9) 4 XXX PWD 0 01 PWD1 02 PWD 2 03 PWD 3 Unlock (10) 7 00 25 00 03 00 PWD 0 01 PWD 1 Command Set Exit (7) 2 XX 90 XX 00 Command Set Entry (5) 3 555 AA 2AA 55 555 C0 PPB Program (11) 2 XX A0 SA 00 00 30 XX 80 SA RD(0) Command Set Exit (7) 2 XX 90 XX 00 Command Set Entry (5) 3 555 AA 2AA 55 XX 00 XX XX A0 XXX RD(0) Command Set Exit (7) 2 XX Command Set Entry (5) 3 555 90 fo 2 1 AA 2AA 55 2 XX A0 SA 00 DYB Clear 2 XX A0 SA 01 XX 00 1 SA RD(0) Command Set Exit (7) 2 XX 90 es PWD 3 00 29 D 03 555 50 00 DYB Set DYB Status Read PWD 2 Data Seventh Add r Data ew 2 1 PPB Lock Bit Status Read 02 Sixth Add r rN All PPB Erase (11, 12) PPB Status Read PPB Lock Bit Set Data ig n Command Set Entry (5) Add r d Global Volatile Sector Protection Freeze (PPB Lock) Data de Non-Volatile Sector Protection (PPB) Addr Third om m en Password Protection Second ec Lock Register Bits First 555 E0 N ot R Legend X = Don’t care. RA = Address of the memory location to be read. SA = Sector Address. Any address that falls within a specified sector. See Tables – for sector address ranges. PWA = Password Address. Address bits A1 and A0 are used to select each 16-bit portion of the 64-bit entity. PWD = Password Data. RD(0) = DQ0 protection indicator bit. If protected, DQ0 = 0. If unprotected, DQ0 = 1. Notes 1. All values are in hexadecimal. 2. Shaded cells indicate read cycles. 3. Address and data bits not specified in table, legend, or notes are don’t cares (each hex digit implies 4 bits of data). 4. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return the device to reading array data. 5. Entry commands are required to enter a specific mode to enable instructions only available within that mode. 6. No unlock or command cycles required when bank is reading array data. 7. Exit command must be issued to reset the device into read mode; device may otherwise be placed in an unknown state. 8. Entire two bus-cycle sequence must be entered for each portion of the password. 9. Full address range is required for reading password. 10. Password may be unlocked or read in any order. Unlocking requires the full password (all seven cycles). 11. ACC must be at VIH when setting PPB or DYB. 12. “All PPB Erase” command pre-programs all PPBs before erasure to prevent over-erasure. Document Number: 002-01522 Rev. *B Page 56 of 92 S29GL512N S29GL256N S29GL128N Memory Array Commands (x8) Cycles Bus Cycles (Notes 1–5) Command Sequence (Notes) First Second Addr Data RD Addr Third Data Addr Fourth Data Addr Fifth Data RA 1 XXX F0 Manufacturer ID 4 AAA AA 555 55 AAA 90 X00 01 Device ID (8) 6 AAA AA 555 55 AAA 90 X02 XX7E Sector Protect Verify (9) 4 AAA AA 555 55 AAA 90 [SA]X04 Data Secure Device Verify (10) 4 AAA AA 555 55 AAA 90 X06 Data PD 1 AA 98 Program 4 AAA AA 555 55 AAA A0 PA Write to Buffer (12) 6 AAA AA 555 55 PA 25 SA Program Buffer to Flash 1 SA 29 AA PA 55 555 F0 AAA AA 555 55 AAA 20 2 XXX A0 PA PD 2 XXX 80 SA 30 Chip Erase (14) 2 XXX 80 SA 10 Reset 2 XXX 90 XXX 00 AAA AA 555 55 6 AAA AA 555 55 Erase/Program Suspend (15) 1 XXX B0 Erase/Program Resume (16) 1 XXX 30 X1E Data WC PD WBL PD PA AAA 80 AAA AA 555 55 AAA 10 AAA 80 AAA AA 555 55 SA 30 om m en de d 6 Sector Erase Secured Silicon Sector Chip Erase Data rN Program (14) Sector Erase (14) X1C D AAA 3 Data ew 3 Entry fo Unlock Bypass Mode Write to Buffer Abort Reset (13) Addr es CFI Query (11) Data ig n 1 Reset (7) Autoselect Asynchronous Read (6) Sixth Addr Entry 3 AAA AA 555 55 AAA 88 Program (17) 4 AAA AA 555 55 AAA A0 PA PD Read (17) 1 00 Data Exit (17) 4 AAA AA 555 55 AAA 90 XXX 00 N ot R ec Legend X = Don’t care. RA = Read Address. RD = Read Data. PA = Program Address. Addresses latch on the falling edge of WE# or CE# pulse, whichever occurs later. PD = Program Data. Data latches on the rising edge of WE# or CE# pulse, whichever occurs first. SA = Sector Address. Any address that falls within a specified sector. See Tables – for sector address ranges. WBL = Write Buffer Location. Address must be within the same write buffer page as PA. WC = Word Count. Number of write buffer locations to load minus 1. Notes 1. See Table on page 10 for description of bus operations. 2. All values are in hexadecimal. 3. Shaded cells indicate read cycles. 4. Address and data bits not specified in table, legend, or notes are don’t cares (each hex digit implies 4 bits of data). 5. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return reading array data. 6. No unlock or command cycles required when bank is reading array data. 7. Reset command is required to return to reading array data in certain cases. See Reset Command on page 43 for details. 8. Data in cycles 5 and 6 are listed in Table on page 34. 9. The data is 00h for an unprotected sector and 01h for a protected sector. PPB Status Read provides the same data but in inverted form. 10. If DQ7 = 1, region is factory serialized and protected. If DQ7 = 0, region is unserialized and unprotected when shipped from factory. See Secured Silicon Sector Flash Memory Region on page 39 for more information. 11. Command is valid when device is ready to read array data or when device is in autoselect mode. 12. Total number of cycles in the command sequence is determined by the number of words written to the write buffer. 13. Command sequence resets device for next command after write-to-buffer operation. 14. Requires Entry command sequence prior to execution. Unlock Bypass Reset command is required to return to reading array data. Document Number: 002-01522 Rev. *B Page 57 of 92 S29GL512N S29GL256N S29GL128N 15. System may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 16. Erase Resume command is valid only during the Erase Suspend mode. 17. Requires Entry command sequence prior to execution. Secured Silicon Sector Exit Reset command is required to exit this mode; device may otherwise be placed in an unknown state. Sector Protection Commands (x8) Data Addr Data Addr Data AA 555 55 AAA 40 XXX Data 00 AAA 60 PWD 2 Command Set Entry (5) 3 AAA Program (6) 2 XXX A0 Read (6) 1 00 Data 2 XXX 90 XXX 3 AAA AA 555 55 Program (8) 2 XXX A0 PWAx PWDx 00 PWD 0 01 PWD1 02 07 PWD 7 00 25 00 03 00 PWD 0 05 PWD 5 06 PWD6 07 PWD 7 1 1 Unlock (10) 90 XX 00 AAA AA 555 55 PPB Program (11) 2 XXX A0 SA 2 XXX 80 1 SA RD(0) 00 30 2 XXX 90 XXX 00 3 AAA AA 555 55 PPB Lock Bit Set 2 XXX A0 XXX 00 PPB Lock Bit Status Read 1 XXX RD(0) XXX 90 XX 00 ec Command Set Exit (7) Command Set Entry (5) Command Set Exit (7) 2 AAA AA 555 55 XXX A0 SA 00 DYB Clear 2 XXX A0 SA 01 DYB Status Read 1 SA RD(0) Command Set Exit (7) 2 XXX 90 XXX 00 N 3 2 DYB Set AAA C0 AAA 50 AAA E0 5th Data Add r Data 6th Add r Data 7th Add r Data PWD 3 04 PWD 4 05 PWD 5 06 PWD 6 01 PWD 1 02 PWD 2 03 PWD 3 04 PWD 4 00 29 03 00 om m en All PPB Erase (11, 12) PPB Status Read Command Set Entry (5) Volatile Sector Protection (DYB) d XX 3 ot Global Volatile Sector Protection Freeze (PPB Lock) 2 R Non-Volatile Sector Protection (PPB) Command Set Exit (7) Command Set Entry (5) rN 8 fo Read (9) Password Protection Addr ew Command Set Exit (7) Command Set Entry (5) 4th/11th ig n Addr de Lock Register Bits 3rd/10th es Command Sequence (Notes) 2nd/9th D Cycles Bus Cycles (Notes 1–4) 1st/8th Legend X = Don’t care. RA = Address of the memory location to be read. SA = Sector Address. Any address that falls within a specified sector. See Tables – for sector address ranges. PWA = Password Address. Address bits A1 and A0 are used to select each 16-bit portion of the 64-bit entity. PWD = Password Data. RD(0) = DQ0 protection indicator bit. If protected, DQ0 = 0. If unprotected, DQ0 = 1. Notes 1. All values are in hexadecimal. 2. Shaded cells indicate read cycles. 3. Address and data bits not specified in table, legend, or notes are don’t cares (each hex digit implies 4 bits of data). 4. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return the device to reading array data. 5. Entry commands are required to enter a specific mode to enable instructions only available within that mode. Document Number: 002-01522 Rev. *B Page 58 of 92 S29GL512N S29GL256N S29GL128N 6. No unlock or command cycles required when bank is reading array data. 7. Exit command must be issued to reset the device into read mode; device may otherwise be placed in an unknown state. 8. Entire two bus-cycle sequence must be entered for each portion of the password. 9. Full address range is required for reading password. 10. Password may be unlocked or read in any order. Unlocking requires the full password (all seven cycles). 11. ACC must be at VIH when setting PPB or DYB. 12. “All PPB Erase” command pre-programs all PPBs before erasure to prevent over-erasure. 10. Write Operation Status DQ7: Data# Polling es 10.1 ig n The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table on page 63 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/ BY#, to determine whether an Embedded Program or Erase operation is in progress or is completed. ew D The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. d fo rN During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the read mode. om m en de During the Embedded Erase algorithm, Data# Polling produces a 0 on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a 1 on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. N ot R ec Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data outputs on DQ0–DQ6 may be still invalid. Valid data on DQ0–DQ7 appears on successive read cycles. Table on page 63 shows the outputs for Data# Polling on DQ7. Figure 10.1 on page 60 shows the Data# Polling algorithm. Figure 15.4 on page 72 shows the Data# Polling timing diagram. Document Number: 002-01522 Rev. *B Page 59 of 92 S29GL512N S29GL256N S29GL128N Figure 10.1 Data# Polling Algorithm START Read DQ15–DQ0 Addr = VA Yes DQ7 = Data? DQ5 = 1 es No ig n No D Yes rN fo Yes d DQ7 = Data? ew Read DQ15–DQ0 Addr = VA de No PASS om m en FAIL Notes 1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. RY/BY#: Ready/Busy# R 10.2 ec 2. DQ7 should be rechecked even if DQ5 = 1 because DQ7 may change simultaneously with DQ5. N ot The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the read mode, the standby mode, or in the erase-suspend-read mode. Table on page 63 shows the outputs for RY/BY#. 10.3 DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. Document Number: 002-01522 Rev. *B Page 60 of 92 S29GL512N S29GL256N S29GL128N The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erasesuspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling). If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table on page 63 shows the outputs for Toggle Bit I on DQ6. Figure 10.2 shows the toggle bit algorithm. Figure 15.8 on page 74 shows the toggle bit timing diagrams. Figure 15.9 on page 74 shows the differences between DQ2 and DQ6 in graphical form. See also DQ2: Toggle Bit II on page 62. ig n Figure 10.2 Toggle Bit Algorithm D es START fo Read DQ7–DQ0 rN ew Read DQ7–DQ0 No de d Toggle Bit = Toggle? om m en Yes DQ5 = 1? Yes Read DQ7–DQ0 Twice N ot R ec No Toggle Bit = Toggle? No Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Note The system should recheck the toggle bit even if DQ5 = 1 because the toggle bit may stop toggling as DQ5 changes to 1. See the subsections on DQ6 and DQ2 for more information. Document Number: 002-01522 Rev. *B Page 61 of 92 S29GL512N S29GL256N S29GL128N 10.4 DQ2: Toggle Bit II The Toggle Bit II on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table on page 63 to compare outputs for DQ2 and DQ6. 10.5 es ig n Figure 10.2 on page 61 shows the toggle bit algorithm in flowchart form, and the section DQ2: Toggle Bit II on page 62 explains the algorithm. See also the RY/BY#: Ready/Busy# on page 60. Figure 15.8 on page 74 shows the toggle bit timing diagram. Figure 15.9 on page 74 shows the differences between DQ2 and DQ6 in graphical form. Reading Toggle Bits DQ6/DQ2 rN ew D Refer to Figure 10.2 on page 61 and Figure 15.9 on page 74 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. om m en de d fo However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. DQ5: Exceeded Timing Limits R 10.6 ec The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 10.2 on page 61). ot DQ5 indicates whether the program, erase, or write-to-buffer time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a 1, indicating that the program or erase cycle was not successfully completed. N The device may output a 1 on DQ5 if the system tries to program a 1 to a location that was previously programmed to 0. Only an erase operation can change a 0 back to a 1. Under this condition, the device halts the operation, and when the timing limit is exceeded, DQ5 produces a 1. In all these cases, the system must write the reset command to return the device to the reading the array (or to erase-suspend-read if the device was previously in the erase-suspend-program mode). Document Number: 002-01522 Rev. *B Page 62 of 92 S29GL512N S29GL256N S29GL128N 10.7 DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a 0 to a 1. If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. See also Sector Erase Command Sequence on page 50. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is 1, the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is 0, the device accepts additional sector erase commands. To ensure the command is accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. DQ1: Write-to-Buffer Abort es 10.8 ig n Table on page 63 shows the status of DQ3 relative to the other status bits. ew D DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a 1. The system must issue the Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data. See Write Buffer on page 11 for more details. EraseSuspend Read Non-Program Suspended Sector Erase-Suspended Sector Non-Erase Suspended Sector Busy (Note 3) Abort (Note 4) DQ2 (Note 2) DQ1 RY/BY# DQ7# Toggle 0 N/A No toggle 0 0 0 Toggle 1 Toggle N/A 0 fo DQ3 de 0 1 DQ7# No toggle Toggle Invalid (not allowed) 1 Data 1 0 N/A Toggle N/A Data 0 1 1 N/A N/A N/A 0 DQ7# Toggle 0 N/A N/A 0 0 DQ7# Toggle 0 N/A N/A 1 0 N Write-toBuffer ot Erase-Suspend-Program (Embedded Program) DQ5 (Note 1) om m en Erase Suspend Mode ProgramSuspend Read Program-Suspended Sector DQ6 ec Program Suspend Mode Embedded Erase Algorithm R Standard Mode Embedded Program Algorithm DQ7 (Note 2) d Status rN Write Operation Status Notes 1. DQ5 switches to 1 when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. Refer to the section on DQ5 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. DQ1 switches to 1 when the device has aborted the write-to-buffer operation Document Number: 002-01522 Rev. *B Page 63 of 92 S29GL512N S29GL256N S29GL128N 11. Absolute Maximum Ratings Storage Temperature, Plastic Packages –65°C to +150°C Ambient Temperature with Power Applied –65°C to +125°C Voltage with Respect to Ground: VCC (Note 1) –0.5 V to +4.0 V VIO –0.5 V to +4.0 V A9 and ACC (Note 2) –0.5 V to +12.5 V All other pins (Note 1) –0.5 V to VCC + 0.5V Output Short Circuit Current (Note 3) 200 mA ig n Notes 1. Minimum DC voltage on input or I/Os is –0.5 V. During voltage transitions, inputs or I/Os may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on input or I/Os is VCC + 0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 11.2. es 2. Minimum DC input voltage on pins A9 and ACC is –0.5 V. During voltage transitions, A9 and ACC may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC input voltage on pin A9 and ACC is +12.5 V which may overshoot to +14.0V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. ew D 4. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. rN Figure 11.1 Maximum Negative Overshoot Waveform de om m en –0.5 V 20 ns d +0.8 V fo 20 ns –2.0 V 20 ns ec Figure 11.2 Maximum Positive Overshoot Waveform R 20 ns N ot VCC +2.0 V VCC +0.5 V 2.0 V 20 ns Document Number: 002-01522 Rev. *B 20 ns Page 64 of 92 S29GL512N S29GL256N S29GL128N 12. Operating Ranges Industrial (I) Devices Ambient Temperature (TA) –40°C to +85°C Supply Voltages VCC VIO (Note 2) +2.7 V to +3.6 V or +3.0 V to 3.6 V +1.65 V to 1.95 V or VCC Notes 1. Operating ranges define those limits between which the functionality of the device is guaranteed. 2. See Product Selector Guide on page 4. es D Parameter Description (Notes) Test Conditions Min Input Load Current (1) VIN = VSS to VCC, VCC = VCC max ILIT A9 Input Load Current VCC = VCC max; A9 = 12.5 V ILO Output Leakage Current VOUT = VSS to VCC, VCC = VCC max fo ILI CE# = VIL; OE# = VIH, VCC = VCCmax; f = 1 MHz, Byte Mode 1 10 CE# = VIL, OE# = VIH, VCC = VCCmax; f=33 MHz 5 20 CE# = VIL, OE# = VIH, VCC = VCCmax 50 90 mA VCC = VCCmax; VIO = VCC; OE# = VIH; VIL = VSS + 0.3 V / –0.1 V; CE#, RESET# = VCC ± 0.3 V 1 5 µA 1 5 µA 1 5 µA WP#/ ACC pin 10 20 VCC pin 50 90 d CE# = VIL; OE# = VIH, VCC = VCCmax; f = 10 MHz de ICC4 VCC Standby Current ICC5 VCC Reset Current ot N µA 90 mA mA ec VCC Active Erase/Program Current (2, 3) µA 60 R ICC3 35 ±1.0 50 CE# = VIL; OE# = VIH, VCC = VCCmax; VCC Intra-Page Read Current (1) µA 30 f = 10 MHz ICC2 Others: ±1.0 Unit 20 CE# = VIL; OE# = VIH, VCC = VCCmax; f = 5 MHz, Word Mode VCC Active Read Current (1) Max WP/ACC: ±2.0 6 om m en ICC1 Typ ew Parameter Symbol CMOS Compatible rN 13.1 ig n 13. DC Characteristics VCC = VCCmax; VIO = VCC; VIL = VSS + 0.3 V / –0.1 V; RESET# = VSS ± 0.3 V VCC = VCCmax; VIO = VCC; ICC6 Automatic Sleep Mode (4) VIH = VCC ± 0.3 V; VIL = VSS + 0.3 V / –0.1 V; WP#/ACC = VIH IACC ACC Accelerated Program Current CE# = VIL, OE# = VIH, VCC = VCCmax, WP#/ACC = VIH mA VIL Input Low Voltage (5) –0.1 0.3 x VIO V VIH Input High Voltage (5) 0.7 x VIO VIO + 0.3 V VHH Voltage for ACC Erase/Program Acceleration VCC = 2.7–3.6 V 11.5 12.5 V VID Voltage for Autoselect and Temporary Sector Unprotect VCC = 2.7–3.6 V 11.5 12.5 V Document Number: 002-01522 Rev. *B Page 65 of 92 S29GL512N S29GL256N S29GL128N Parameter Symbol Parameter Description (Notes) Test Conditions VOL Output Low Voltage (5) IOL = 100 µA VOH Output High Voltage (5) IOH = -100 µA VLKO Low VCC Lock-Out Voltage (3) Min Typ Max Unit 0.15 x VIO V 0.85 x VIO V 2.3 2.5 V Notes 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. ICC active while Embedded Erase or Embedded Program or Write Buffer Programming is in progress. 3. Not 100% tested. 4. Automatic sleep mode enables the lower power mode when addresses remain stable tor tACC + 30 ns. 5. VIO = 1.65–1.95 V or 2.7–3.6 V ig n 6. VCC = 3 V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at 3V. es 14. Test Conditions D Figure 14.1 Test Setup rN ew 3.3 V 2.7 k 6.2 k om m en de CL d fo Device Under Test ot R ec Note Diodes are IN3064 or equivalent N Test Specifications Test Condition All Speeds Output Load Output Load Capacitance, CL (including jig capacitance) Input Rise and Fall Times Unit 1 TTL gate 30 pF 5 ns Input Pulse Levels 0.0–VIO V Input timing measurement reference levels (See Note) 0.5VIO V Output timing measurement reference levels 0.5 VIO V Note If VIO < VCC, the reference level is 0.5 VIO. Document Number: 002-01522 Rev. *B Page 66 of 92 S29GL512N S29GL256N S29GL128N 14.1 Key to Switching Waveforms Waveform Inputs Outputs Steady Changing from H to L Changing from L to H Changing, State Unknown Does Not Apply Center Line is High Impedance State (High Z) ig n Don’t Care, Any Change Permitted 0.5 VIO Input Measurement Level 0.5 VIO V Output ew 0.0 V D VIO es Figure 14.2 Input Waveforms and Measurement Levels N ot R ec om m en de d fo rN Note If VIO < VCC, the input measurement reference level is 0.5 VIO. Document Number: 002-01522 Rev. *B Page 67 of 92 S29GL512N S29GL256N S29GL128N 15. AC Characteristics Read-Only Operations Parameter Speed Options Std. Description Test Setup tAVAV tRC Read Cycle Time tAVQV tACC Address to Output Delay (Note 2) tELQV tCE Chip Enable to Output Delay (Note 3) VIO = VCC = 3 V 100 110 90 100 110 Min VIO = 1.8 V, VCC = 3 V VIO = VCC = 3 V Max VIO = 1.8 V, VCC = 3 V VIO = VCC = 3 V Max VIO = 1.8 V, VCC = 3 V 110 90 90 Max 25 Output Enable to Output Delay Max 25 Max Output Enable to Output High Z (Note 1) Max tAXQX tOH Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First tOEH Output Enable Hold Time (Note 1) tCEH Chip Enable Hold Time Read ns ns 30 ns 35 ns 35 20 ns 20 ns Min 0 ns Min 0 ns Min 10 ns Min 35 ns d Read ns 25 25 fo Toggle and Data# Polling 110 D Chip Enable to Output High Z (Note 1) tDF 25 ew tDF 100 Unit rN Page Access Time tEHQZ 110 110 tOE tGHQZ 100 110 tGLQV tPACC 110 ig n JEDEC 90 (Note 6) es 15.1 de Notes 1. Not 100% tested. om m en 2. CE#, OE# = VIL 3. OE# = VIL 4. See Figure 14.1 on page 66 and Table on page 66 for test specifications. 5. Unless otherwise indicated, AC specifications for 90 ns, 100 ns, and 110 ns speed options are tested with VIO = VCC = 3 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. ot R ec 6. 90 ns speed option only applicable to S29GL128N and S29GL256N. CE# tRC Addresses Stable N Addresses Figure 15.1 Read Operation Timings tACC tCEH tRH tRH tDF tOE OE# tOEH WE# tCE tOH HIGH Z HIGH Z Output Valid Outputs RESET# RY/BY# 0V Document Number: 002-01522 Rev. *B Page 68 of 92 S29GL512N S29GL256N S29GL128N Figure 15.2 Page Read Timings Same Page Amax-A2 A2-A0* Aa Ab tACC Data Bus Qa Ad Ac tPACC tPACC tPACC Qb Qc Qd CE# OE# es Hardware Reset (RESET#) D 15.2 ig n Note * Figure shows word mode. Addresses are A2–A-1 for byte mode. Description Max tReady RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode (Note 1) Max Reset High Time Before Read (Note 1) tRPD RESET# Low to Standby Mode tRB RY/BY# Recovery Time Speed (Note 2) Unit 20 ns 500 ns Min 500 ns Min 50 ns Min 20 µs Min 0 ns d RESET# Pulse Width de tRP tRH fo tReady RESET# Pin Low (During Embedded Algorithms) to Read Mode (Note 1) rN Std. om m en JEDEC ew Parameter Notes 1. Not 100% tested. If ramp rate is equal to or faster than 1V/100µs with a falling edge of the RESET# pin initiated, the RESET# pin needs to be held low only for 100µs for power-up. N ot R ec 2. Next generation devices may have different reset speeds. To increase system design considerations, please refer to Advance Information on S29GL-P Hardware Reset (RESET#) and Power-up Sequence on page 80 for advance reset speeds on S29GL-P devices. Document Number: 002-01522 Rev. *B Page 69 of 92 S29GL512N S29GL256N S29GL128N Figure 15.3 Reset Timings RY/BY# CE#, OE# tRH RESET# tRP tReady ig n Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms es tReady D RY/BY# ew tRB rN CE#, OE# fo RESET# tRH N ot R ec om m en de d tRP Document Number: 002-01522 Rev. *B Page 70 of 92 S29GL512N S29GL256N S29GL128N 15.3 Erase and Program Operations Parameter Speed Options 100 110 110 Unit 90 100 110 110 ns tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min 0 ns tASO Address Setup Time to OE# low during toggle bit polling Min 15 ns tAH Address Hold Time Min 45 ns tAHT Address Hold Time From CE# or OE# high during toggle bit polling Min 0 ns tDS Data Setup Time Min 45 ns tDH ns 20 tOEPH Output Enable High during toggle bit polling Min 20 tGHWL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 tCS CE# Setup Time Min tCH CE# Hold Time Min tWLWH tWP Write Pulse Width Min tWHDL tWPH Write Pulse Width High Min Write Buffer Program Operation (Notes 2, 3) Typ Effective Write Buffer Program Operation (Notes 2, 4) Per Word Typ Accelerated Effective Write Buffer Program Operation (Notes 2, 4) Per Word Program Operation (Note 2) Typ ns ns ns 0 ns 35 ns 30 ns 240 µs 15 µs 13.5 µs Word Typ 60 µs Word Typ 54 µs tWHWH2 Sector Erase Operation (Note 2) Typ 0.5 sec tVHH VHH Rise and Fall Time (Note 1) Min 250 ns tVCS VCC Setup Time (Note 1) Min 50 µs tBUSY Erase/Program Valid to RY/BY# Delay Max 90 ns R ot Notes 1. Not 100% tested. ec Accelerated Programming Operation (Note 2) tWHWH2 de tWHWH1 om m en tWHWH1 0 d tELWL tWHEH es 0 Min D Min CE# High during toggle bit polling ew tGHWL Data Hold Time tCEPH rN tWHDX fo tDVWH ig n Std. tWLAX Description 90 (Note 6) JEDEC N 2. See Erase And Programming Performance on page 77 for more information. 3. For 1–16 words/1–32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 5. Unless otherwise indicated, AC specifications for 90 ns, 100 ns, and 110 ns speed options are tested with VIO = VCC = 3 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. 6. 90 ns speed option only applicable to S29GL128N and S29GL256N. Document Number: 002-01522 Rev. *B Page 71 of 92 S29GL512N S29GL256N S29GL128N Figure 15.4 Program Operation Timings Program Command Sequence (last two cycles) tWC Addresses Read Status Data (last two cycles) tAS 555h PA PA PA tAH CE# tCH OE# tWHWH1 tWP WE# Data es tDH PD A0h Status DOUT D tDS ig n tWPH tCS tRB ew tBUSY rN RY/BY# VCC fo tVCS d Notes 1. PA = program address, PD = program data, DOUT is the true data at the program address. om m en de 2. Illustration shows device in word mode. Figure 15.5 Accelerated Program Timing Diagram VIL or VIH R ACC ec VHH 3. OE# = VIL N 2. CE#, OE# = VIL tVHH ot tVHH Notes 1. Not 100% tested. VIL or VIH 4. See Figure 14.1 on page 66 and Table on page 66 for test specifications. Document Number: 002-01522 Rev. *B Page 72 of 92 S29GL512N S29GL256N S29GL128N Figure 15.6 Chip/Sector Erase Operation Timings Erase Command Sequence (last two cycles) tAS tWC 2AAh Addresses Read Status Data VA SA VA 555h for chip erase tAH CE# tCH OE# tWP tWPH tCS tWHWH2 tDS tDH 55h In Progress 30h Complete es Data ig n WE# 10 for Chip Erase D tBUSY ew RY/BY# tRB tVCS rN VCC fo Notes 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write Operation Status on page 59). de d 2. These waveforms are for the word mode. om m en Figure 15.7 Data# Polling Timings (During Embedded Algorithms) tRC Addresses VA VA tCE R CE# VA ec tACC tCH N tOEH ot tOE OE# WE# tDF tOH High Z DQ7 Complement Complement Status Data Status Data True Valid Data High Z DQ6–DQ0 True Valid Data tBUSY RY/BY# Notes 1. VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. 2. tOE for data polling is 45 ns when VIO = 1.65 to 2.7 V and is 35 ns when VIO = 2.7 to 3.6 V. Document Number: 002-01522 Rev. *B Page 73 of 92 S29GL512N S29GL256N S29GL128N Figure 15.8 Toggle Bit Timings (During Embedded Algorithms) tAHT tAS Addresses tAHT tASO CE# tCEPH tOEH WE# tOEPH tDH Valid Status Valid Status (first read) (second read) (stops toggling) Valid Data es Valid Status D DQ2 and DQ6 tOE Valid Data ig n OE# ew RY/BY# fo rN Notes VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle WE# Enter Erase Suspend Program de Erase Suspend om m en Enter Embedded Erasing d Figure 15.9 DQ2 vs. DQ6 Erase Erase Suspend Read Erase Suspend Read Erase Erase Complete ot DQ2 R ec DQ6 Erase Suspend Program Erase Resume N Note DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6. Document Number: 002-01522 Rev. *B Page 74 of 92 S29GL512N S29GL256N S29GL128N 15.4 Alternate CE# Controlled Erase and Program Operations: S29GL128N, S29GL256N, S29GL512N Parameter Speed Options 100 90 100 Std. tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min 0 ns Address Setup Time to OE# low during toggle bit polling Min 15 ns tAH Address Hold Time Min 45 ns tAHT Address Hold Time From CE# or OE# high during toggle bit polling Min 0 ns tDVEH tDS Data Setup Time Min 45 ns tEHDX tDH Data Hold Time Min 0 tELAX 110 110 Unit 110 110 ns ig n JEDEC TASO Description 90 (Note 6) ns CE# High during toggle bit polling Min 20 OE# High during toggle bit polling Min 20 tGHEL tGHEL Read Recovery Time Before Write (OE# High to WE# Low) Min tWLEL tWS WE# Setup Time Min tEHWH tWH WE# Hold Time Min tELEH tCP CE# Pulse Width Min tEHEL tCPH CE# Pulse Width High Min 30 ns Write Buffer Program Operation (Notes 2, 3) Typ 240 µs µs ew D ns ns 0 ns 35 ns rN d fo Per Word 15 Effective Accelerated Write Buffer Program Operation (Notes 2, 4) Per Word Typ 13.5 µs Word Typ 60 µs Word Typ 54 µs Typ 0.5 sec Program Operation (Note 2) Accelerated Programming Operation (Note 2) tWHWH2 0 0 tWHWH2 Sector Erase Operation (Note 2) R ec Notes 1. Not 100% tested. Typ de tWHWH1 ns Effective Write Buffer Program Operation (Notes 2, 4) om m en tWHWH1 ns es tCEPH tOEPH 2. See AC Characteristics on page 68 for more information. ot 3. For 1–16 words/1–32 bytes programmed. N 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 5. Unless otherwise indicated, AC specifications for 90 ns, 100ns, and 110 ns speed options are tested with VIO = VCC = 3 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. 6. 90 ns speed option only applicable to S29GL128N and S29GL256N. Document Number: 002-01522 Rev. *B Page 75 of 92 S29GL512N S29GL256N S29GL128N Figure 15.10 Alternate CE# Controlled Write (Erase/Program) Operation Timings PA for program SA for sector erase 555 for chip erase 555 for program 2AA for erase Data# Polling Addresses PA tWC tAS tAH tWH WE# tGHEL OE# tWS tCPH es CE# ig n tWHWH1 or 2 tCP tBUSY D tDS ew tDH DQ7# tRH PD for program 30 for sector erase 10 for chip erase fo A0 for program 55 for erase DOUT rN Data de d RESET# om m en RY/BY# Notes 1. Figure indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. N ot R ec 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. Document Number: 002-01522 Rev. *B Page 76 of 92 S29GL512N S29GL256N S29GL128N 16. Erase And Programming Performance Parameter Sector Erase Time Chip Erase Time Typ (Note 1) Max (Note 2) Unit 0.5 3.5 sec S29GL128N 64 256 S29GL256N 128 512 S29GL512N 256 1024 sec Total Write Buffer Programming Time (Note 3) 240 µs Total Accelerated Effective Write Buffer Programming Time (Note 3) 200 µs 123 S29GL256N 246 S29GL512N 492 Excludes 00h programming prior to erasure (Note 4) Excludes system level overhead (Note 5) sec ig n Chip Program Time S29GL128N Comments es Notes 1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 10,000 cycles, checkerboard pattern. D 2. Under worst case conditions of 90°C, VCC = 3.0 V, 100,000 cycles. 3. Effective write buffer specification is based upon a 16-word write buffer operation. ew 4. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. fo rN 5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table on page 54 and Table on page 57 for further information on command definitions. de d 17. TSOP Pin and BGA Package Capacitance Parameter Description Test Setup CIN Input Capacitance VIN = 0 COUT Output Capacitance VOUT = 0 CIN2 Control Pin Capacitance VIN = 0 ec om m en Parameter Symbol Max Unit TSOP 6 7.5 pF BGA 4.2 5.0 pF TSOP 8.5 12 pF BGA 5.4 6.5 pF TSOP 7.5 9 pF BGA 3.9 4.7 pF ot R Notes 1. Sampled, not 100% tested. Typ N 2. Test conditions TA = 25°C, f = 1.0 MHz. Document Number: 002-01522 Rev. *B Page 77 of 92 S29GL512N S29GL256N S29GL128N 18. Physical Dimensions TS056—56-Pin Standard Thin Small Outline Package (TSOP) TS 56 JEDEC MO-142 (B) EC MIN. NOM. NOTES: 1 CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm). (DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.) MAX. ot SYMBOL R PACKAGE ec om m en de d fo rN ew D es ig n 18.1 --- --- 1.20 2 PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP). 0.05 --- 0.15 3 A2 0.95 1.00 1.05 b1 0.17 0.20 0.23 TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE. b c1 0.17 0.10 0.22 --- 0.27 0.16 4 DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS 0.15 mm PER SIDE. 5 c 0.10 --- 0.21 DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm. 6 THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10 mm AND 0.25 mm FROM THE LEAD TIP. 7 LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE SEATING PLANE. 8 DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS. N A A1 D 19.80 20.00 20.20 D1 18.30 18.40 18.50 E 13.90 14.00 14.10 e L 0.50 BASIC 0.50 0.60 0.70 O 0˚ - 8˚ R 0.08 --- 0.20 N 56 Document Number: 002-01522 Rev. *B 3160\38.10A Page 78 of 92 S29GL512N S29GL256N S29GL128N LAA064—64-Ball Fortified Ball Grid Array (FBGA) LAA 064 N/A 13.00 mm x 11.00 mm PACKAGE SYMBOL MIN NOM MAX A --- --- 1.40 A1 0.40 --- --- A2 0.60 --- --- 13.00 BSC. E 11.00 BSC. 7.00 BSC. E1 7.00 BSC. MD 8 φb 0.50 STANDOFF 2. ALL DIMENSIONS ARE IN MILLIMETERS. 3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT AS NOTED). 4. MATRIX FOOTPRINT MATRIX FOOTPRINT MATRIX SIZE D DIRECTION 8 MATRIX SIZE E DIRECTION BALL COUNT 0.70 BALL DIAMETER eD 1.00 BSC. BALL PITCH - D DIRECTION eE 1.00 BSC. BALL PITCH - E DIRECTION SD / SE 0.50 BSC. SOLDER BALL PLACEMENT NONE DEPOPULATED SOLDER BALLS e REPRESENTS THE SOLDER BALL GRID PITCH. 5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE "D" DIRECTION. SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE "E" DIRECTION. BODY THICKNESS 64 0.60 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. N IS THE TOTAL NUMBER OF SOLDER BALLS. BODY SIZE ot N N ME PROFILE HEIGHT NOTES: BODY SIZE R D1 NOTE ec D om m en JEDEC de PACKAGE d fo rN ew D es ig n 18.2 6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 7 SD AND SE ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW PARALLEL TO THE D OR E DIMENSION, RESPECTIVELY, SD OR SE = 0.000. WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, SD OR SE = e/2 8. NOT USED. 9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS. 3354 \ 16-038.12d Document Number: 002-01522 Rev. *B Page 79 of 92 S29GL512N S29GL256N S29GL128N 19. Advance Information on S29GL-P Hardware Reset (RESET#) and Powerup Sequence Hardware Reset (RESET#) Parameter Std. Description Speed Unit Min 35 µs RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode or Write mode Min 35 µs µs tReady RESET# Pin Low (During Embedded Algorithms) to Read Mode or Write mode tReady tRP RESET# Pulse Width Min 35 tRH Reset High Time Before Read Min 200 ns tRPD RESET# Low to Standby Mode Min 10 µs tRB RY/BY# Recovery Time Min 0 ns ew D es Note CE#, OE# and WE# must be at logic high during Reset Time. ig n JEDEC rN Figure 19.1 Reset Timings d fo RY/BY# de CE#, OE# om m en tRH RESET# tRP tReady Reset Timings during Embedded Algorithms R ec Reset Timings NOT during Embedded Algorithms ot tReady N RY/BY# tRB CE#, OE# RESET# tRP Document Number: 002-01522 Rev. *B tRH Page 80 of 92 S29GL512N S29GL256N S29GL128N Power-Up Sequence Timings Parameter Description Speed Unit Min 35 µs Reset Low Time from Rising Edge of VIO (or last Reset pulse) to Rising Edge of RESET# Min 35 µs Reset High Time Before Read Max 200 ns tVCS Reset Low Time from Rising Edge of VCC (or last Reset pulse) to Rising Edge of RESET# tVIOS tRH Notes 1. VIO < VCC + 200 mV. 2. VIO and VCC ramp must be in sync during power up. If RESET# is not stable for 35 µs, the following conditions may occur: the device does not permit any read and write operations, valid read operations return FFh, and a hardware reset is required. ig n 3. Maximum VCC power up current is 20 mA (RESET# =VIL). D VIO Vcc_min Vio_min t RH rN CE# ew VCC es Figure 19.2 Power-On Reset Timings fo t VIOS t VCS N ot R ec om m en de d RESET# Document Number: 002-01522 Rev. *B Page 81 of 92 S29GL512N S29GL256N S29GL128N 20. Advance Information on S29GL-R 65 nm MirrorBit Hardware Reset (RESET#) and Power-up Sequence Hardware Reset (RESET#) Parameter Description Limit Time Unit tRPH RESET# Low to CE# Low Min 35 µs tRP RESET# Pulse Width Min 200 ns tRH Time between RESET# (high) and CE# (low) Min 200 ns ig n Note CE#, OE# and WE# must be at logic high during Reset Time. es Figure 20.1 Reset Timings D tRP RESET# ew tRH rN tRPH fo CE# de d Note The sum of tRP and tRH must be equal to or greater than tRPH. om m en Power-Up Sequence Timings Parameter Description VCC Setup Time to first access tVIOS VIO Setup Time to first access tRPH RESET# Low to CE# Low tRP RESET# Pulse Width tRH Time between RESET# (high) and CE# (low) R Time Unit Min 300 µs Min 300 µs Min 35 µs Min 200 ns Min 200 ns ot Limit N Notes 1. VIO < VCC + 200 mV. ec tVCS 2. VIO and VCC ramp must be in sync during power-up. If RESET# is not stable for 300 µs, the following conditions may occur: the device does not permit any read and write operations, valid read operations return FFh, and a hardware reset is required. 3. Maximum VCC power up current is 20 mA (RESET# =VIL). Document Number: 002-01522 Rev. *B Page 82 of 92 S29GL512N S29GL256N S29GL128N Figure 20.2 Power-On Reset Timings VCC V IO t VIOS t VCS t RP RESET# t RH t RPH ig n CE# N ot R ec om m en de d fo rN ew D es Note The sum of tRP and tRH must be equal to or greater than tRPH. Document Number: 002-01522 Rev. *B Page 83 of 92 S29GL512N S29GL256N S29GL128N 21. Document History Page Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU ** - RYSU Submission Date Description of Change 09/03/2003 A:Initial release Spansion Publication Number: S29GL-N_00 10/16/2003 A1:Global Added LAA064 package. Distinctive Characteristics, Performance Characteristics Clarified fifth bullet information. Added RTSOP to Package Options. Distinctive Characteristics, Software and Hardware Features Clarified Password Sector Protection to Advanced Sector Protection Connection Diagrams Removed Note. Ordering Information Modified Package codes Device Bus Operations, Table 1 Modified Table, removed Note. Sector Address Tables All address ranges doubled in all sector address tables. Sector Protection Lock Register: Corrected text to reflect 3 bits instead of 4. Table 6, Lock Register: Corrected address range from DQ15-5 to DQ15-3; removed DQ4 and DQ3; Corrected DQ15-3 Lock Register to Don’t Care. Table 7, Sector Protection Schemes: Corrected Sector States. Command Definitions Table 12, Command Definitions, x16 Nonvolatile Sector Protection Command Set Entry Second Cycle Address corrected from 55 to 2AA. Legend: Clarified PWDx, DATA Notes: Clarified Note 19. Table 13, Command Definitions, x8 N ot R ec om m en de d fo rN ew D es ig n Rev. Password Read and Unlock Addresses and Data corrected. Legend: Clarified PWDx, DATA Notes: Clarified Note 19. Test Conditions Table Test Specifications and Figure Input Waveforms and Measurement Levels: Corrected Input Pulse Levels to 0.0–VIO; corrected Input timing measurement reference levels to 0.5VIO. Document Number: 002-01522 Rev. *B Page 84 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU ** - RYSU Submission Date Description of Change 01/22/2004 A2:Lock Register Corrected and added new text for Secured Silicon Sector Protection Bit, Persistent Protection Mode Lock Bit, and Password Protection Mode Lock Bit. Persistent Sector Protection Persistent Protection Bit (PPB): Added the second paragraph text about programming the PPB bit. Persistent Protection Bit Lock (PPB Lock Bit): Added the second paragraph text about configuring the PPB Lock Bit, and fourth paragraph on Autoselect Sector Protection Verification. Added PPB Lock Bit requirement of 200ns access time. Password Sector Protection Corrected 1 μs (built-in delay for each password check) to 2 μs. Lock Register Command Set Definitions Added new information for this section. Password Protection Command Set Definitions Added new information for this section. Non-Volatile Sector Protection Command Set Definitions Added new information for this section. Global Volatile Sector Protection Freeze Command Set Added new information for this section. Volatile Sector Protection Command Set Added new information for this section. Secured Silicon Sector Entry Command Added new information for this section. Secured Silicon Sector Exit Command Added new information for this section. R ec om m en de d fo rN ew D es ig n Rev. N ot 03/02/2004 A3:Connection Diagrams Removed 56-pin reverse TSOP diagram. Ordering Information Updated the Standard Products for the S29GL512/256/128N devices and modified the valid combinations tables. Word Program Command Sequence Added new information to this section. Lock Register Command Set Definitions Added new information to this section. Table 13 Updated this table. Document Number: 002-01522 Rev. *B Page 85 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU Submission Date Description of Change 05/13/2004 A4:Global Removed references to RTSOP. Distinctive Characteristics Removed 16-word/32-byte page read buffer from Performance Characteristics. Changed Low power consumption to 25 mA typical active read current and removed 10 mA typical intrapage active read current. Ordering Information Changed formatting of pages. Changed model numbers from 00,01,02,03 to 01, 02, V1, V2. Table Device Bus Operations Combined WP# and ACC columns. Tables CFI Query Identification String, System Interface String, Device Geometry Definition, and Primary Vendor-Specific Extended Query Added Address (x8) column. Word Program Command Sequence Added text to fourth paragraph. Figure Write Buffer Programming Operation Added note references and removed DQ15 and DQ13. Figure Program Suspend/Program Resume Changed field to read XXXh/B0h and XXXh/30h. Password Protection Command Set Definitions Replaced all text. Command Definitions Changed the first cycle address of CFI Query to 55. Memory Array Commands (x8) Table Changed the third cycle data Device ID to 90. Removed Unlock Bypass Reset. Removed Note 12 and 13. Figure Data# Polling Algorithm Removed DQ15 and DQ13. Absolute Maximum Ratings Removed VCC from All other pins with respect to Ground. CMOS Compatible Changed the Max of ICC4 to 70 mA. Added VIL to the Test conditions of ICC5, ICC6, and ICC7 Change the Min of VIL to - 0.1 V. Updated note 5. Read-Only Operations–S29GL128N Only Added tCEH parameter to table.1/8/16 Figure Read Operation Timings Added tCEH to figure. N ot R ec om m en de d fo rN ew D es ig n Rev. Document Number: 002-01522 Rev. *B Page 86 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU ** - RYSU Submission Date Description of Change 05/13/2004 Figure Page Read Timings Change A1-A0 to A2-A0. Erase and Program Operations Updated tWHWH1 and tWHWH2 with values. Figure Chip/Sector Erase Operation Timings Changed 5555h to 55h and 3030h to 30h. Figure Data# Polling Timings (During Embedded Algorithms) Removed DQ15 and DQ14-DQ8 Added Note 2 Figure Toggle Bit Timings (During Embedded Algorithms) Changed DQ6 & DQ14/DQ2 & DQ10 to DQ2 and DQ6. Alternate CE# Controlled Erase and Program Operations Updated tWHWH1 and tWHWH2 with values. Latchup Characteristics Removed Table. Erase and Programming Performance Updated TBD with values. Updated Note 1 and 2. Physical Dimensions Removed the reverse pinout information and note 3. 09/29/2004 A5:Performance Characteristics N ot R ec om m en de d fo rN ew D es ig n Rev. Document Number: 002-01522 Rev. *B Removed 80 ns. Product Selector Guide Updated values in tables. Ordering Information Created a family table. Operating Ranges Updated VIO. CMOS Characteristics Created a family table. Read-Only Operations Created a family table. Hardware Reset (RESET#) Created a family table. Figure 13, “Reset Timings,” Added tRH to waveform. Erase and Program Operations Created a family table. Alternate CE# Controlled Erase and Program Operations Created a family table. Erase and Programming Performance Created a family table. Page 87 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU ** - RYSU Submission Date Description of Change 01/24/2005 A6:Global Updated access times for S29GL512N. Product Selector Guides All tables updated. Valid Combinations Tables All tables updated. AC Characteristics Read-Only Options Table Added note for 90 ns speed options. AC Characteristics Erase and Programming Performance Table Added note for 90 ns speed options. Figure Data# Polling Timings (During Embedded Algorithms) Updated timing diagram. AC Characteristics Alternate CE# Controlled Erase and Program Operations Table Added note for 90 ns speed options. 02/14/2005 A7:Distinctive Characteristics fo rN ew D es ig n Rev. - RYSU 05/09/2005 A8:Product Availability Table Updated data in VCC and availability columns. Product Selector Guide Combined GL128N and GL256N tables. Changed upper limit of VIO voltage range to 3.6 V. Ordering Information Added wireless temperature range. Combined valid combinations table and updated for wireless temperature range part numbers. DC Characteristics table Added VIO = VCC test condition to ICC4, ICC5, ICC6 specifications. Corrected unit of measure on ICC4 to μA. Changed maximum specifications for IACC (on ACC pin) and ICC3 to 90 mA. Tables Memory Array Commands (x16) to Sector Protection Commands (x8), Memory Array and Sector Protection (x8 & x16) Re-formatted command definition tables for easier reference. Advance Information on S9GL-P AC Characteristics Changed speed specifications and units of measure for tREADY, tRP, tRH, and tRPD. Changed specifications on tREADY from maximum to minimum. N ot R ec ** om m en de d Added Product Availability Table Ordering Information Under Model Numbers, changed VIO voltage values for models V1 and V2. Physical Dimensions Updated Package Table Document Number: 002-01522 Rev. *B Page 88 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU Submission Date Description of Change 06/15/2005 A9:Ordering Information table Added note to temperature range. Valid Combinations table Replaced table. DC Characteristics table Replaced VIL lines for ICC4, ICC5, ICC6. Connection Diagrams Modified 56-Pin Standard TSOP. Modified 64-ball Fortified BGA. Advance Information on S9GL-P AC Characteristics Added second table. N ot R ec om m en de d fo rN ew D es ig n Rev. Document Number: 002-01522 Rev. *B Page 89 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ECN No. Orig. of Change ** - RYSU ** - Submission Date Description of Change 04/22/2006 B0:Global Changed document status to Full Production. Ordering Information Changed description of “A” for Package Materials Set. Modified S29GL128N Valid Combinations table. S29GL128N Sector Address Table Corrected bit range values for A22–A16. Persistent Protection Bit (PPB) Corrected typo in second sentence, second paragraph. Secured Silicon Sector Flash Memory Region Deleted note at end of second paragraph. Customer Lockable: Secured Silicon Sector NOT Programmed or Protected At the Factory Modified 1st bullet text. Write Protect (WP#) Modified third paragraph. Device Geometry Definition table Changed 1st x8 address for Erase Block Region 2. Word Program Command Sequence Modified fourth paragraph. Write Buffer Programming Deleted note from eighth paragraph. Program Suspend/Program Resume Command Sequence Corrected typos in first paragraph. Lock Register Command Set Definitions Modified fifth paragraph. Volatile Sector Protection Command Set Modified fourth paragraph. Sector Protection Commands (x16) table Changed read command address for Lock Register Bits Memory Array Commands (x8) Added Program and Unlock Bypass Mode commands to table. Write Operation Status Deleted note (second paragraph). DC Characteristics table Modified test conditions for ICC4. 05/05/2006 B1:Ordering Information N ot R ec om m en de d fo rN ew D es ig n Rev. RYSU Modified speed option, package material set, temperature range descriptions in breakout diagram. Modified Note 1. Advance Information on S29GL-P AC Characteristics Hardware Reset (RESET#) Replaced contents in section. ** - RYSU 10/03/2006 Connection Diagrams Corrected 56-pin TSOP package drawing. Document Number: 002-01522 Rev. *B Page 90 of 92 S29GL512N S29GL256N S29GL128N (Continued) Document Title:S29GL512N, S29GL256N, S29GL128N 512, 256, 128 Mbit, 3 V, Page Flash Featuring 110 nm MirrorBit Document Number: 002-01522 ** - RYSU ** - RYSU ** - RYSU ** - RYSU Submission Date Description of Change 01/19/2007 B4:Global Added obsolescence and migration notice. Product Selector Guide Changed manimum VIO for VCC = 2.7–3.6V and VIO = 1.65 V minimum. 02/06/2007 B5:Global Revised obsolescence and migration notice. 11/08/2007 B6:Advance Information on S29GL-R 65nm MirrorBit Hardware Reset (RESET#) and Power-up Sequence Added advanced information 02/12/2008 B7:Erase And Programming Performance ig n Orig. of Change es ECN No. D Rev. - RYSU *A 5043543 RYSU *B 5074572 RYSU 04/22/2008 B8:End of Life Notice Added “retired product” status text to cover page, Distinctive Characteristics page and Ordering Information sections of data sheet. 12/11/2015 Updated to Cypress Template om m en de d ** fo rN ew Chip Program Time: removed comment Advance Information on S29GL-R 65nm MirrorBit Hardware Reset (RESET#) and Power-up Sequence Power-Up Sequence Timings table: reduced timing from 500 μs to 300 μs N ot R ec 01/08/2016 Updated the suggested replacement parts in the note in blue font in page 1. Removed Spansion Revision History Document Number: 002-01522 Rev. *B Page 91 of 92 S29GL512N S29GL256N S29GL128N Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products PSoC® Solutions Automotive..................................cypress.com/go/automotive psoc.cypress.com/solutions Clocks & Buffers ................................ cypress.com/go/clocks PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP Interface......................................... cypress.com/go/interface Cypress Developer Community Lighting & Power Control............ cypress.com/go/powerpsoc Community | Forums | Blogs | Video | Training Memory........................................... cypress.com/go/memory Technical Support PSoC ....................................................cypress.com/go/psoc cypress.com/go/support ig n Touch Sensing .................................... cypress.com/go/touch USB Controllers....................................cypress.com/go/USB N ot R ec om m en de d fo rN ew D es Wireless/RF .................................... cypress.com/go/wireless © Cypress Semiconductor Corporation, 2003-2016. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 002-01522 Rev. *B ® ® ® ® Revised January 08, 2016 Page 92 of 92 Cypress , Spansion , MirrorBit , MirrorBit Eclipse™, ORNAND™, EcoRAM™, HyperBus™, HyperFlash™, and combinations thereof, are trademarks and registered trademarks of Cypress Semiconductor Corp. All products and company names mentioned in this document may be the trademarks of their respective holders.