0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
S29GL256P10TFI020

S29GL256P10TFI020

  • 厂商:

    EUPEC(英飞凌)

  • 封装:

    TFSOP56

  • 描述:

    IC FLASH 256MBIT PARALLEL 56TSOP

  • 详情介绍
  • 数据手册
  • 价格&库存
S29GL256P10TFI020 数据手册
S29GL01GP S29GL512P S29GL256P S29GL128P 1 Gbit, 512, 256, 128 Mbit, 3 V, Page Flash with 90 nm MirrorBit Process Technology General Description The Cypress S29GL01G/512/256/128P are Mirrorbit® Flash products fabricated on 90 nm process technology. These devices offer a fast page access time of 25 ns with a corresponding random access time as fast as 90 ns. They feature a Write Buffer that allows a maximum of 32 words/64 bytes to be programmed in one operation, resulting in faster effective programming time than standard programming algorithms. This makes these devices ideal for today’s embedded applications that require higher density, better performance and lower power consumption. Distinctive Characteristics  Single 3V read/program/erase (2.7-3.6 V)  20-year data retention typical  Enhanced VersatileI/O™ control – All input levels (address, control, and DQ input levels) and outputs are determined by voltage on VIO input. VIO range is 1.65 to VCC  Offered Packages – 56-pin TSOP – 64-ball Fortified BGA  Suspend and Resume commands for Program and Erase operations  90 nm MirrorBit process technology  8-word/16-byte page read buffer  Write operation status bits indicate program and erase operation completion  32-word/64-byte write buffer reduces overall programming time for multiple-word updates  Unlock Bypass Program command to reduce programming time  Secured Silicon Sector region – 128-word/256-byte sector for permanent, secure identification through an 8-word/16-byte random Electronic Serial Number – Can be programmed and locked at the factory or by the customer  Support for CFI (Common Flash Interface)  Persistent and Password methods of Advanced Sector Protection  WP#/ACC input – Accelerates programming time (when VHH is applied) for greater throughput during system production – Protects first or last sector regardless of sector protection settings  Uniform 64 Kword/128 Kbyte Sector Architecture – S29GL01GP: One thousand twenty-four sectors – S29GL512P: Five hundred twelve sectors – S29GL256P: Two hundred fifty-six sectors – S29GL128P: One hundred twenty-eight sectors  Hardware reset input (RESET#) resets device  Ready/Busy# output (RY/BY#) detects program or erase cycle completion  100,000 erase cycles per sector typical Performance Characteristics Maximum Read Access Times (ns) Density 128 & 256 Mb 512 Mb 1 Gb Random Access Time (tACC) Voltage Range (1) Regulated VCC 90 Full VCC 100/110 Page Access Time (tPACC) CE# Access Time OE# Access Time (tCE) (tOE) 90 25 100/110 VersatileIO VIO 110 110 Regulated VCC 100 100 Full VCC 110 VersatileIO VIO 120 Regulated VCC 110 Full VCC 120 VersatileIO VIO 130 25 110 25 25 120 110 25 120 25 130 Notes 1. Access times are dependent on VCC and VIO operating ranges. See Ordering Information page for further details. Regulated VCC: VCC = 3.0–3.6 V. Full VCC: VCC = VIO = 2.7–3.6 V. VersatileIO VIO: VIO = 1.65–VCC, VCC = 2.7–3.6 V. 2. Contact a sales representative for availability. Cypress Semiconductor Corporation Document Number: 002-00886 Rev. *B • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised May 22, 2017 S29GL01GP S29GL512P S29GL256P S29GL128P Current Consumption (typical values) Random Access Read (f = 5 MHz) 30 mA 8-Word Page Read (f = 10 MHz) 1 mA Program/Erase 50 mA Standby 1 µA Program & Erase Times (typical values) Single Word Programming 60 µs Effective Write Buffer Programming (VCC) Per Word 15 µs Effective Write Buffer Programming (VHH) Per Word 13.5 µs Sector Erase Time (64 Kword Sector) Document Number: 002-00886 Rev. *B 0.5 s Page 2 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Contents 1. Ordering Information ................................................... 4 11.7 AC Characteristics ........................................................ 53 2. Input/Output Descriptions & Logic Symbol .............. 6 3. Block Diagram.............................................................. 7 4. 4.1 4.2 4.3 4.4 Physical Dimensions/Connection Diagrams............. 8 Related Documents ....................................................... 8 Special Handling Instructions for BGA Package............ 8 LAA064—64 ball Fortified Ball Grid Array, 11 x 13 mm. 9 TS056—56-Pin Standard Thin Small Outline Package (TSOP)......................................................................... 11 12. Appendix ..................................................................... 64 12.1 Command Definitions.................................................... 64 12.2 Common Flash Memory Interface................................. 73 5. 5.1 5.2 5.3 5.4 Additional Resources ................................................ Application Notes ......................................................... Specification Bulletins .................................................. Hardware and Software Support.................................. Contacting Cypress...................................................... 6. 6.1 Product Overview ...................................................... 13 Memory Map ................................................................ 13 7. 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 Device Operations ..................................................... Device Operation Table ............................................... Word/Byte Configuration.............................................. Versatile IOTM (VIO) Control ......................................... Read ............................................................................ Page Read Mode ......................................................... Autoselect .................................................................... Program/Erase Operations .......................................... Write Operation Status................................................. Writing Commands/Command Sequences.................. 15 15 16 16 16 16 17 21 32 36 8. 8.1 8.2 8.3 8.4 8.5 8.6 Advanced Sector Protection/Unprotection ............. Lock Register ............................................................... Persistent Protection Bits............................................. Persistent Protection Bit Lock Bit................................. Password Protection Method ....................................... Advanced Sector Protection Software Examples ........ Hardware Data Protection Methods............................. 38 39 39 41 41 44 44 9. 9.1 9.2 9.3 9.4 Power Conservation Modes...................................... Standby Mode.............................................................. Automatic Sleep Mode................................................. Hardware RESET# Input Operation............................. Output Disable (OE#)................................................... 45 45 45 45 45 10. 10.1 10.2 10.3 Secured Silicon Sector Flash Memory Region ....... Factory Locked Secured Silicon Sector ....................... Customer Lockable Secured Silicon Sector................. Secured Silicon Sector Entry/Exit Command Sequences ................................................................... 46 46 47 Electrical Specifications............................................ Absolute Maximum Ratings ......................................... Operating Ranges........................................................ Test Conditions ............................................................ Key to Switching Waveforms ....................................... Switching Waveforms .................................................. DC Characteristics ....................................................... 49 49 50 50 51 51 52 11. 11.1 11.2 11.3 11.4 11.5 11.6 Document Number: 002-00886 Rev. *B 13. Advance Information on S29GL-S Eclipse 65 nm MirrorBit Power-On and Warm Reset Timing ........... 77 14. Document History ....................................................... 79 12 12 12 12 12 47 Page 3 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 1. Ordering Information The ordering part number is formed by a valid combination of the following: S29GL01GP 12 F F I 01 0 PACKING TYPE 0 = Tray (standard (Note 5)) 2 = 7” Tape and Reel 3 = 13” Tape and Reel MODEL NUMBER (VIO range, protection when WP# =VIL) 01 = VIO = VCC = 2.7 to 3.6 V, highest address sector protected 02 = VIO = VCC = 2.7 to 3.6 V, lowest address sector protected V1 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6 V, highest address sector protected V2 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6 V, lowest address sector protected R1= VIO = VCC = 3.0 to 3.6 V, highest address sector protected R2= VIO = VCC = 3.0 to 3.6 V, lowest address sector protected TEMPERATURE RANGE I = Industrial (–40°C to +85°C) C = Commercial (0°C to +85°C) PACKAGE MATERIALS SET A = Pb (Note 1) F = Pb-free PACKAGE TYPE T = 56-pin Thin Small Outline Package (TSOP) Standard Pinout(TSO56) F = 64-ball Fortified Ball Grid Array, 1.0 mm pitch package (LAA064) SPEED OPTION 90 = 90 ns 10 = 100 ns 11 = 110 ns 12 = 120 ns 13 = 130 ns DEVICE NUMBER/DESCRIPTION S29GL01GP, S29GL512P, S29GL256P, S29GL128P 3.0 Volt-only, 1024, 512, 256 and 128 Megabit Page-Mode Flash Memory, manufactured on 90 nm MirrorBit® process technology Recommended Combinations Recommended Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to confirm availability of specific recommended combinations and to check on newly released combinations. Document Number: 002-00886 Rev. *B Page 4 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P S29GL-P Valid Combinations Base Part Number Speed Package (2)(3) 11 12 S29GL01GP TA (1), TF 13 11 12 10 S29GL512P TA (1), TF 10 FA (1), FF 90 10, 11 I I I I I, C TA (1), TF 11 90 10, 11 R1, R2 I, C 12 S29GL128P, S29GL256P I, C I, C 12 11 Model Number I, C FA (1), FF 13 11 Temperature (4) I I, C FA (1), FF 11 I 01, 02 Packing Type (5) 0, 3 V1, V2 R1, R2 01, 02 0, 2, 3 V1, V2 R1, R2 01, 02 0, 3 V1, V2 R1, R2 01, 02 0, 2, 3 V1, V2 R1, R2 01, 02 0, 3 V1, V2 R1, R2 01, 02 0, 2, 3 V1, V2 Notes 1. Contact a local sales representative for availability. 2. TSOP package marking omits packing type designator from ordering part number. 3. BGA package marking omits leading “S29” and packing type designator from ordering part number. 4. Operating Temperature range: I = Industrial (–40°C to +85°C) C = Commercial (0°C to +85°C) 5. Type 0 is standard. Specify other options as required. Document Number: 002-00886 Rev. *B Page 5 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 2. Input/Output Descriptions & Logic Symbol Table identifies the input and output package connections provided on the device. Input/Output Descriptions Symbol Type Description Address lines for GL01GP A24–A0 for GL512P A23–A0 for GL256P, A22–A0 for GL128P. A25–A0 Input DQ14–DQ0 I/O Data input/output. DQ15/A-1 I/O DQ15: Data input/output in word mode. A-1: LSB address input in byte mode. CE# Input Chip Enable. OE# Input Output Enable. WE# Input Write Enable. VCC Supply Device Power Supply. VIO Supply Versatile IO Input. VSS Supply Ground. NC No Connect Not connected internally. RY/BY# Output Ready/Busy. Indicates whether an Embedded Algorithm is in progress or complete. At VIL, the device is actively erasing or programming. At High Z, the device is in ready. BYTE# Input Selects data bus width. At VIL, the device is in byte configuration and data I/O pins DQ0-DQ7 are active and DQ15/A-1 becomes the LSB address input. At VIH, the device is in word configuration and data I/O pins DQ0-DQ15 are active. RESET# Input Hardware Reset. Low = device resets and returns to reading array data. Input Write Protect/Acceleration Input. At VIL, disables program and erase functions in the outermost sectors. At VHH, accelerates programming; automatically places device in unlock bypass mode. Should be at VIH for all other conditions. WP# has an internal pull-up; when unconnected, WP# is at VIH. WP#/ACC Document Number: 002-00886 Rev. *B Page 6 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 3. Block Diagram Figure 3.1 S29GL-P Block Diagram DQ15–DQ0 RY/BY# VCC Sector Switches VSS VIO Erase Voltage Generator RESET# WE# WP#/ACC BYTE# Input/Output Buffers State Control Command Register PGM Voltage Generator Chip Enable Output Enable CE# STB Data OE# VCC Detector AMax**–A0 (A- Timer Address Latch STB Y-Decoder Y-Gating X-Decoder Cell Matrix ** AMax GL01GP=A25, AMax GL512P = A24, AMax GL256P = A23, AMax GL128P = A22 Document Number: 002-00886 Rev. *B Page 7 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 4. Physical Dimensions/Connection Diagrams This section shows the I/O designations and package specifications for the S29GL-P family. 4.1 Related Documents The following documents contain information relating to the S29GL-P devices. Click on the title or go to www.cypress.com download the PDF file, or request a copy from your sales office.  Considerations for X-ray Inspection of Surface-Mounted Flash Integrated Circuits 4.2 Special Handling Instructions for BGA Package Special handling is required for Flash Memory products in BGA packages. Flash memory devices in BGA packages may be damaged if exposed to ultrasonic cleaning methods. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. Figure 4.1 64-ball Fortified Ball Grid Array Top View, Balls Facing Down NC on S29GL128P NC on S29GL256P NC on S29GL512P A8 B8 C8 D8 E8 F8 G8 H8 NC A22 A23 VIO VSS A24 A25 NC A7 B7 C7 D7 E7 F7 G7 H7 A13 A12 A14 A15 A16 BYTE# DQ15/A-1 VSS A6 B6 C6 D6 E6 F6 G6 H6 A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 A5 B5 C5 D5 E5 F5 G5 H5 WE# RESET# A21 A19 DQ5 DQ12 VCC DQ4 A4 B4 C4 D4 E4 F4 G4 H4 A18 A20 DQ2 DQ10 DQ11 DQ3 RY/BY# WP#/ACC A3 B3 C3 D3 E3 F3 G3 H3 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1 A2 B2 C2 D2 E2 F2 G2 H2 A3 A4 A2 A1 A0 CE# OE# VSS A1 B1 C1 D1 E1 F1 G1 H1 NC NC NC NC NC VIO NC NC Document Number: 002-00886 Rev. *B Page 8 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 4.3 LAA064—64 ball Fortified Ball Grid Array, 11 x 13 mm Figure 4.2 LAA064—64ball Fortified Ball Grid Array (FBGA), 11 x 13 mm NOTES: PACKAGE LAA 064 JEDEC 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. N/A 2. ALL DIMENSIONS ARE IN MILLIMETERS. 13.00 mm x 11.00 mm PACKAGE 3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT AS NOTED). SYMBOL MIN NOM MAX NOTE A --- --- 1.40 A1 0.40 --- --- STANDOFF A2 0.60 --- --- BODY THICKNESS PROFILE HEIGHT D 13.00 BSC. BODY SIZE E 11.00 BSC. BODY SIZE D1 7.00 BSC. MATRIX FOOTPRINT E1 7.00 BSC. MATRIX FOOTPRINT MD 8 MATRIX SIZE D DIRECTION ME 8 MATRIX SIZE E DIRECTION N 64 BALL COUNT φb 0.50 0.60 0.70 BALL DIAMETER eD 1.00 BSC. BALL PITCH - D DIRECTION eE 1.00 BSC. BALL PITCH - E DIRECTION SD / SE 0.50 BSC. SOLDER BALL PLACEMENT NONE DEPOPULATED SOLDER BALLS 4. e REPRESENTS THE SOLDER BALL GRID PITCH. 5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE "D" DIRECTION. SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE "E" DIRECTION. N IS THE TOTAL NUMBER OF SOLDER BALLS. 6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 7 SD AND SE ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW PARALLEL TO THE D OR E DIMENSION, RESPECTIVELY, SD OR SE = 0.000. WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, SD OR SE = e/2 8. NOT USED. 9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS. 3354 \ 16-038.12d Document Number: 002-00886 Rev. *B Page 9 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Figure 4.3 56-pin Standard TSOP (Top View) NC on S29GL128P NC on S29GL256P NC on S29GL512P A23 A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Document Number: 002-00886 Rev. *B 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 A24 A25 A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 NC VIO Page 10 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 4.4 TS056—56-Pin Standard Thin Small Outline Package (TSOP) Figure 4.4 56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm PACKAGE JEDEC SYMBOL NOTES: TS 56 MO-142 (B) EC MIN. NOM. MAX. 1 CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm). (DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.) A --- --- 1.20 2 PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP). A1 0.05 --- 0.15 3 A2 0.95 1.00 1.05 b1 0.17 0.20 0.23 TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE. b c1 0.17 0.10 0.22 --- 0.27 0.16 4 DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS 0.15 mm PER SIDE. 5 c 0.10 --- 0.21 DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm. 6 THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10 mm AND 0.25 mm FROM THE LEAD TIP. 7 LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE SEATING PLANE. 8 DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS. D 19.80 20.00 20.20 D1 18.30 18.40 18.50 E 13.90 14.00 14.10 e L 0.50 BASIC 0.50 0.60 0.70 O 0˚ - 8˚ R 0.08 --- 0.20 N 56 Document Number: 002-00886 Rev. *B 3160\38.10A Page 11 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 5. Additional Resources Visit www.cypress.com to obtain the following related documents: 5.1 Application Notes The following is a list of application notes related to this product. All Cypress application notes are available at http:// www.cypress.com/Support/TechnicalDocuments/Pages/ApplicationNotes.aspx  Using the Operation Status Bits in AMD Devices  Understanding Page Mode Flash Memory Devices  MirrorBit® Flash Memory Write Buffer Programming and Page Buffer Read  Common Flash Interface Version 1.4 Vendor Specific Extensions  MirrorBit® Flash Memory Write Buffer Programming and Page Buffer Read  Taking Advantage of Page Mode Read on the MCF5407 Coldfire  Migration to S29GL128N and S29GL256N based on 110nm MirrorBit® Technology  Optimizing Program/Erase Times  Practical Guide to Endurance and Data Retention  Configuring FPGAs using Cypress S29GL-N Flash  Connecting Cypress™ Flash Memory to a System Address Bus  Connecting Unused Data Lines of MirrorBit® Flash  Reset Voltage and Timing Requirements for MirrorBit® Flash  Versatile IO: DQ and Enhanced 5.2 Specification Bulletins Contact your local sales office for details. 5.3 Hardware and Software Support Downloads and related information on Flash device support is available at http://www.cypress.com/Support/Pages/DriversSoftware.aspx  Cypress low-level drivers  Enhanced Flash drivers  Flash file system Downloads and related information on simulation modeling and CAD modeling support is available at http://www.cypress.com/Support/Pages/SimulationModels.aspx  VHDL and Verilog  IBIS  ORCAD 5.4 Contacting Cypress Obtain the latest list of company locations and contact information on our web site at http://www.cypress.com/About/Pages/Locations.aspx Document Number: 002-00886 Rev. *B Page 12 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 6. Product Overview The S29GL-P family consists of 1 Gb, 512 Mb, 256 Mb and 128 Mb, 3.0-volt-only, page mode Flash devices optimized for today’s embedded designs that demand a large storage array and rich functionality. These devices are manufactured using 90 nm MirrorBit technology. These products offer uniform 64 Kword (128 Kbyte) uniform sectors and feature VersatileIO control, allowing control and I/O signals to operate from 1.65 V to VCC. Additional features include:  Single word programming or a 32-word programming buffer for an increased programming speed  Program Suspend/Resume and Erase Suspend/Resume  Advanced Sector Protection methods for protecting sectors as required  128 words/256 bytes of Secured Silicon area for storing customer and factory secured information. The Secured Silicon Sector is One Time Programmable. 6.1 Memory Map The S29GL-P devices consist of uniform 64 Kword (128 Kbyte) sectors organized as shown in Table –Table . S29GL01GP Sector & Memory Address Map Uniform Sector Size Sector Count Sector Range 64 Kword/128 Kbyte 1024 Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA1023 3FF0000H - 3FFFFFFh Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA1022) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. S29GL512P Sector & Memory Address Map Uniform Sector Size Sector Count 64 Kword/128 Kbyte 512 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA511 1FF0000H - 1FFFFFFh Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sector starting and ending addresses that the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. S29GL256P Sector & Memory Address Map Uniform Sector Size 64 Kword/ 128 Kbyte Sector Count 256 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA255 0FF0000H - 0FFFFFFh Document Number: 002-00886 Rev. *B Sector Ending Address Page 13 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA254) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. S29GL128P Sector & Memory Address Map Uniform Sector Size 64 Kword/ 128 Kbyte Sector Count 128 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA127 07F0000 - 7FFFFF Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. Document Number: 002-00886 Rev. *B Page 14 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 7. Device Operations This section describes the read, program, erase, handshaking, and reset features of the Flash devices. Operations are initiated by writing specific commands or a sequence with specific address and data patterns into the command registers (see Table through Table ). The command register itself does not occupy any addressable memory location; rather, it is composed of latches that store the commands, along with the address and data information needed to execute the command. The contents of the register serve as input to the internal state machine and the state machine outputs dictate the function of the device. Writing incorrect address and data values or writing them in an improper sequence may place the device in an unknown state, in which case the system must pull the RESET# pin low or power cycle the device to return the device to the reading array data mode. 7.1 Device Operation Table The device must be setup appropriately for each operation. Table describes the required state of each control pin for any particular operation. Device Operations Operation DQ8–DQ15 Addresses WP#/ACC (Note 1) DQ0–DQ7 BYTE#= VIH BYTE#= VIL CE# OE# WE# RESET# Read L L H H X AIN DOUT DOUT Write (Program/ Erase) L H L H (Note 2) AIN (Note 3) (Note 3) Accelerated Program L H L H VHH AIN (Note 3) (Note 3) VCC ± 0.3 V X X VCC ± 0.3 V H X High-Z High-Z High-Z Output Disable L H H H X X High-Z High-Z High-Z Reset X X X L X X High-Z High-Z High-Z Standby DQ8–DQ14 = High-Z, DQ15 = A-1 Legend L = Logic Low = VIL, H = Logic High = VIH, VHH = 11.5–12.5V, X = Don’t Care, AIN = Address In, DIN = Data In, DOUT = Data Out Notes 1. Addresses are AMax:A0 in word mode; AMax:A-1 in byte mode. 2. If WP# = VIL, on the outermost sector remains protected. If WP# = VIH, the outermost sector is unprotected. WP# has an internal pull-up; when unconnected, WP# is at VIH. All sectors are unprotected when shipped from the factory (The Secured Silicon Sector can be factory protected depending on version ordered.) 3. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm. Document Number: 002-00886 Rev. *B Page 15 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 7.2 Word/Byte Configuration The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0-DQ15 are active and controlled by CE# and OE#. If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ0-DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8-DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. 7.3 Versatile IOTM (VIO) Control The VersatileIOTM (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on all inputs and outputs (address, control, and DQ signals). VIO range is 1.65 to VCC. See Ordering Information on page 4 for VIO options on this device. For example, a VIO of 1.65-3.6 volts allows for I/O at the 1.8 or 3 volt levels, driving and receiving signals to and from other 1.8 or 3 V devices on the same data bus. 7.4 Read All memories require access time to output array data. In a read operation, data is read from one memory location at a time. Addresses are presented to the device in random order, and the propagation delay through the device causes the data on its outputs to arrive with the address on its inputs. The device defaults to reading array data after device power-up or hardware reset. To read data from the memory array, the system must first assert a valid address on Amax-A0, while driving OE# and CE# to VIL. WE# must remain at VIH. All addresses are latched on the falling edge of CE#. Data will appear on DQ15-DQ0 after address access time (tACC), which is equal to the delay from stable addresses to valid output data. The OE# signal must be driven to VIL. Data is output on DQ15-DQ0 pins after the access time (tOE) has elapsed from the falling edge of OE#, assuming the tACC access time has been meet. 7.5 Page Read Mode The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. The page size of the device is 8 words/16 bytes. The appropriate page is selected by the higher address bits A(max)-A3. Address bits A2-A0 in word mode (A2 to A-1 in byte mode) determine the specific word within a page. The microprocessor supplies the specific word location. The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is de-asserted and reasserted for a subsequent access, the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the “read-page addresses” constant and changing the “intra-read page” addresses. Document Number: 002-00886 Rev. *B Page 16 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 7.6 Autoselect The Autoselect mode provides manufacturer ID, Device identification, and sector protection information, through identifier codes output from the internal register (separate from the memory array) on DQ7-DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm (see Table ). The Autoselect codes can also be accessed in-system. There are two methods to access autoselect codes. One uses the autoselect command, the other applies VID on address pin A9. When using programming equipment, the autoselect mode requires VID (11.5 V to 12.5 V) on address pin A9. Address pins must be as shown in Table .  To access Autoselect mode without using high voltage on A9, the host system must issue the Autoselect command.  The Autoselect command sequence may be written to an address within a sector that is either in the read or erase-suspend-read mode.  The Autoselect command may not be written while the device is actively programming or erasing.  The system must write the reset command to return to the read mode (or erase-suspend-read mode if the sector was previously in Erase Suspend).  It is recommended that A9 apply VID after power-up sequence is completed. In addition, it is recommended that A9 apply from VID to VIH/VIL before power-down the VCC/VIO.  See Table on page 65 for command sequence details.  When verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table to Table ). The remaining address bits are don't care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ15-DQ0. The Autoselect codes can also be accessed in-system through the command register. Document Number: 002-00886 Rev. *B Page 17 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Autoselect Codes, (High Voltage Method) Description Device ID Device ID Device ID Device ID S29GL128P S29GL256P S29GL512P S29GL01GP Manufacturer ID: Cypress Product Ama x to CE# OE# WE# A16 L L H A1 4 to A1 0 X X DQ8 to DQ15 A9 A8 to A7 VID X A6 A5 to A4 A3 to A2 A1 A0 L X L L L 00 X 01h L L H 22 X 7Eh H H L 22 X 28h H H H 22 X 01h Cycle 1 Cycle 2 L L H X X VID X L X Cycle 3 BYTE BYTE #= VIH # = VIL DQ7 to DQ0 Cycle 1 L L H 22 X 7Eh Cycle 2 H H L 22 X 23h Cycle 3 H H H 22 X 01h Cycle 1 L L H 22 X 7Eh H H L 22 X 22h Cycle 3 H H H 22 X 01h Cycle 1 L L H 22 X 7Eh H H L 22 X 21h H H H 22 X 01h L H L X X 01h (protected), 00h (unprotected) Cycle 2 Cycle 2 L L L L L L H X H X H X X X X VID VID VID X X X L L L X X X Cycle 3 Sector Group Protection Verification L L H SA X VID X L X Secured Silicon Sector Indicator Bit (DQ7), WP# protects highest address sector L L H X X VID X L X L H H X X 99h (factory locked), 19h (not factory locked) Secured Silicon Sector Indicator Bit (DQ7), WP# protects lowest address sector L L H X X VID X L X L H H X X 89h (factory locked), 09h (not factory locked) Legend L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care. VID = 11.5V to 12.5V Autoselect Addresses in System Description Address Read Data (word/byte mode) Manufacturer ID Base + 00h xx01h/1h Device ID, Word 1 Base + 01h 227Eh/7Eh Device ID, Word 2 Base + 0Eh 2228h/28h (GL01GP) 2223h/23h (GL512P) 2222h/22h (GL256P) 2221h/21h (GL128P) Document Number: 002-00886 Rev. *B Page 18 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Autoselect Addresses in System Description Address Read Data (word/byte mode) Device ID, Word 3 Base + 0Fh 2201h/01h Secure Device Verify Base + 03h For S29GLxxxPH: XX19h/19h = Not Factory Locked. XX99h/99h = Factory Locked. For S29GLxxxPL: XX09h/09h = Not Factory Locked. XX89h/89h = Factory Locked. Sector Protect Verify (SA) + 02h xx01h/01h = Locked, xx00h/00h = Unlocked Software Functions and Sample Code Autoselect Entry in System (LLD Function = lld_AutoselectEntryCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 0x00AAh Unlock Cycle 2 Write Base + 555h Base + 2AAh 0x0055h Autoselect Command Write Base + AAAh Base + 555h 0x0090h Autoselect Exit (LLD Function = lld_AutoselectExitCmd) Cycle Operation Byte Address Word Address Data Autoselect Exit Command Write base + XXXh base + XXXh 0x00F0h Note 1. Any offset within the device works. 2. base = base address. The following is a C source code example of using the autoselect function to read the manufacturer ID. Refer to the Cypress Low Level Driver User’s Guide (available on www.cypress.com) for general information on Cypress Flash memory software development guidelines. /* Here is an example of Autoselect mode (getting manufacturer ID) */ /* Define UINT16 example: typedef unsigned short UINT16; */ UINT16 manuf_id; /* Auto Select Entry */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)base_addr + 0x555 ) = 0x0090; /* write autoselect command */ /* multiple reads can be performed after entry */ manuf_id = *( (UINT16 *)base_addr + 0x000 ); /* read manuf. id */ /* Autoselect exit */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* exit autoselect (write reset command) */ Document Number: 002-00886 Rev. *B Page 19 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P 7.7 Program/Erase Operations These devices are capable of several modes of programming and or erase operations which are described in detail in the following sections. During a write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Note the following:  When the Embedded Program algorithm is complete, the device returns to the read mode.  The system can determine the status of the program operation by reading the DQ status bits. Refer to the Write Operation Status on page 32 for information on these status bits.  An “0” cannot be programmed back to a “1.” A succeeding read shows that the data is still “0.”  Only erase operations can convert a “0” to a “1.”  Any commands written to the device during the Embedded Program/Erase are ignored except the Suspend commands.  Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress.  A hardware reset and/or power removal immediately terminates the Program/Erase operation and the Program/Erase command sequence should be reinitiated once the device has returned to the read mode to ensure data integrity.  Programming is allowed in any sequence and across sector boundaries for single word programming operation. See Write Buffer Programming on page 23 when using the write buffer.  Programming to the same word address multiple times without intervening erases is permitted. 7.7.1 Single Word Programming Single word programming mode is one method of programming the Flash. In this mode, four Flash command write cycles are used to program an individual Flash address. The data for this programming operation could be 8 or 16-bits wide. While the single word programming method is supported by most Cypress devices, in general Single Word Programming is not recommended for devices that support Write Buffer Programming. See Table on page 65 for the required bus cycles and Figure 7.1 for the flowchart. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by reading the DQ status bits. Refer to Write Operation Status on page 32 for information on these status bits.  During programming, any command (except the Suspend Program command) is ignored.  The Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress.  A hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity.  Programming to the same address multiple times continuously (for example, “walking” a bit within a word) is permitted. Document Number: 002-00886 Rev. *B Page 20 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Figure 7.1 Single Word Program Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Program Command: Address 555h, Data A0h Setup Command Program Address (PA), Program Data (PD) Program Data to Address: PA, PD Perform Polling Algorithm (see Write Operation Status flowchart) Yes Polling Status = Busy? No Yes Polling Status = Done? Error condition (Exceeded Timing Limits) No PASS. Device is in read mode. FAIL. Issue reset command to return to read array mode. Software Functions and Sample Code Single Word/Byte Program (LLD Function = lld_ProgramCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Unlock Cycle 2 Write Base + AAAh Base + 555h 00AAh Base + 555h Base + 2AAh 0055h Program Setup Write Base + AAAh Base + 555h 00A0h Program Write Byte Address Word Address Data Note Base = Base Address. Document Number: 002-00886 Rev. *B Page 21 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P The following is a C source code example of using the single word program function. Refer to the Cypress Low Level Driver User’s Guide (available on www.cypress.com) for general information on Cypress Flash memory software development guidelines. /* Example: Program Command */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)base_addr + 0x555 ) = 0x00A0; /* write program setup command */ *( (UINT16 *)pa ) /* write data to be programmed */ = data; /* Poll for program completion */ 7.7.2 Write Buffer Programming Write Buffer Programming allows the system to write a maximum of 32 words in one programming operation. This results in a faster effective word programming time than the standard “word” programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming occurs. At this point, the system writes the number of “word locations minus 1” that are loaded into the page buffer at the Sector Address in which programming occurs. This tells the device how many write buffer addresses are loaded with data and therefore when to expect the “Program Buffer to Flash” confirm command. The number of locations to program cannot exceed the size of the write buffer or the operation aborts. (Number loaded = the number of locations to program minus 1. For example, if the system programs 6 address locations, then 05h should be written to the device.) The system then writes the starting address/data combination. This starting address is the first address/data pair to be programmed, and selects the “write-buffer-page” address. All subsequent address/data pairs must fall within the elected write-buffer-page. The “write-buffer-page” is selected by using the addresses AMAX–A5. The “write-buffer-page” addresses must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple “write-buffer-pages.” This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected “write-buffer-page”, the operation ABORTs.) After writing the Starting Address/Data pair, the system then writes the remaining address/data pairs into the write buffer. Note that if a Write Buffer address location is loaded multiple times, the “address/data pair” counter is decremented for every data load operation. Also, the last data loaded at a location before the “Program Buffer to Flash” confirm command is the data programmed into the device. It is the software's responsibility to comprehend ramifications of loading a write-buffer location more than once. The counter decrements for each data load operation, NOT for each unique write-buffer-address location. Once the specified number of write buffer locations have been loaded, the system must then write the “Program Buffer to Flash” command at the Sector Address. Any other address/data write combinations abort the Write Buffer Programming operation. The Write Operation Status bits should be used while monitoring the last address location loaded into the write buffer. This eliminates the need to store an address in memory because the system can load the last address location, issue the program confirm command at the last loaded address location, and then check the write operation status at that same address. DQ7, DQ6, DQ5, DQ2, and DQ1 should be monitored to determine the device status during Write Buffer Programming. The write-buffer “embedded” programming operation can be suspended using the standard suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device returns to READ mode. The Write Buffer Programming Sequence is ABORTED under any of the following conditions:  Load a value that is greater than the page buffer size during the “Number of Locations to Program” step.  Write to an address in a sector different than the one specified during the Write-Buffer-Load command.  Write an Address/Data pair to a different write-buffer-page than the one selected by the “Starting Address” during the “write buffer data loading” stage of the operation.  Writing anything other than the Program to Buffer Flash Command after the specified number of “data load” cycles. The ABORT condition is indicated by DQ1 = 1, DQ7 = DATA# (for the “last address location loaded”), DQ6 = TOGGLE, DQ5 = 0. This indicates that the Write Buffer Programming Operation was ABORTED. A “Write-to-Buffer-Abort reset” command sequence is required when using the write buffer Programming features in Unlock Bypass mode. Note that the Secured Silicon sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Document Number: 002-00886 Rev. *B Page 22 of 83 S29GL01GP S29GL512P S29GL256P S29GL128P Write buffer programming is allowed in any sequence of memory (or address) locations. These flash devices are capable of handling multiple write buffer programming operations on the same write buffer address range without intervening erases. Use of the write buffer is strongly recommended for programming when multiple words are to be programmed. Software Functions and Sample Code Write Buffer Program (LLD Functions Used = lld_WriteToBufferCmd, lld_ProgramBufferToFlashCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write 2 Unlock Write Base + AAAh Base + 555h 00AAh Base + 555h Base + 2AAh 0055h 3 Write Buffer Load Command Write Sector Address 0025h 4 Write Word Count Write Sector Address Word Count (N–1)h 5 to 36 Load Buffer Word N Write Program Address, Word N Word N Last Write Buffer to Flash Write Sector Address 0029h Number of words (N) loaded into the write buffer can be from 1 to 32 words (1 to 64 bytes). Notes 1. Base = Base Address. 2. Last = Last cycle of write buffer program operation; depending on number of words written, the total number of cycles may be from 6 to 37. 3. For maximum efficiency, it is recommended that the write buffer be loaded with the highest number of words (N words) possible. The following is a C source code example of using the write buffer program function. Refer to the Cypress Low Level Driver User’s Guide (available on www.cypress.com) for general information on Cypress Flash memory software development guidelines. /* Example: Write Buffer Programming Command */ /* NOTES: Write buffer programming limited to 16 words. */ /* All addresses to be written to the flash in /* one operation must be within the same flash /* page. A flash page begins at addresses /* evenly divisible by 0x20. */ */ */ UINT16 *src = source_of_data; /* address of source data UINT16 *dst = destination_of_data; UINT16 wc */ */ /* flash destination address = words_to_program -1; */ /* word count (minus 1) */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)sector_address ) = 0x0025; /* write write buffer load command */ *( (UINT16 *)sector_address ) = wc; /* write word count (minus 1) */ for (i=0;i
S29GL256P10TFI020
物料型号: - S29GL01GP - S29GL512P - S29GL256P - S29GL128P

器件简介: 赛普拉斯(Cypress)S29GL系列是采用90纳米MirrorBit工艺技术制造的嵌入式闪存产品。这些设备提供1Gbit、512Mbit、256Mbit和128Mbit的存储容量,并且是3.0伏特单电源供电。它们具有快速的页面访问时间(25纳秒)和随机访问时间(最快90纳秒),适用于需要高密度、高性能和低功耗的嵌入式应用。

引脚分配: - A25-A0:地址输入引脚,根据型号不同,地址线数量有所变化。 - DQ14-DQ0:数据输入/输出引脚。 - DQ15/A-1:数据输入/输出或字节模式下的最低位地址输入。 - CE#:芯片使能。 - OE#:输出使能。 - WE#:写使能。 - VIO:多功能I/O输入,用于确定所有输入电平和输出。 - Vcc:电源。 - Vss:地。 - RY/BY#:就绪/忙信号输出,指示编程或擦除周期的完成。 - BYTE#:数据总线宽度选择。 - RESET#:硬件复位输入。 - WP#/ACC:写保护/加速输入。

参数特性: - 工作电压:2.7-3.6V - 数据保留时间:典型值20年 - 增强的多功能I/O控制 - 提供的封装:56引脚TSOP、64球FBGA - 编程/擦除操作的挂起和恢复命令 - 90纳米MirrorBit工艺技术 - 8字/16字节的页面读取缓冲 - 编程和擦除操作状态位

功能详解: - 支持单3V读/编程/擦除 - 20年数据保留 - 增强的多功能I/O控制 - 提供多种封装选项 - 编程和擦除操作可挂起和恢复 - 支持CFI(通用闪存接口)

应用信息: S29GL系列闪存产品适用于需要高存储密度、快速数据访问和高可靠性的应用,如工业控制、汽车电子、医疗设备和高端消费电子产品。

封装信息: - 56引脚TSOP封装 - 64球加固BGA封装
S29GL256P10TFI020 价格&库存

很抱歉,暂时无法提供与“S29GL256P10TFI020”相匹配的价格&库存,您可以联系我们找货

免费人工找货