RL104FG

RL101FG THRU RL107FG Features · High reliability · Low leakage current · Low forward voltage drop · High current capability · Glass passivated junction · High switching capagility CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts A-405 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data · Case : A-405 molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.008 ounce, 0.22 gram 0.025(0.6) 0.021(0.5) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length TA=55℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage at TA=25℃ Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TA=125℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF RL RL RL RL RL RL RL 101FG 102FG 103FG 104FG 105FG 106FG 107FG 50 35 50 100 70 100 200 140 200 400 280 400 1.0 30.0 1.3 5.0 600 420 600 800 560 800 1000 700 1000 Units Volts Volts Volts Amp Amps Volts μA 100 Trr CJ TJ TSTG 150 15.0 -65 to +150 250 500 ns pF ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. RATINGS AND CHARACTERISTIC CURVES RF101FG THRU RF107FG FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NON INDUCTIVE 10W NON INDUCTIVE +0.5A Trr (+) 25Vdc (APPROX) D.U.T. PULSE GENERATOR (NOTE2) 0 -0.25A ( ) NON INDUCTIVE 1W OSCILLOSCOPE (NOTE1) -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.3-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) 50 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 1.50 AVERAGE FORWARD CURRENT(A) 1.25 1.00 0.75 0.50 0.25 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ℃) SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 40 30 20 10 0 1 2 4 6 8 10 20 NUMBER OF CYCLES AT 60Hz 40 60 100 FIG.4-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.5-TYPICAL JUNCTION CAPACITANCE 10 INSTANTANEOUS FORWARD CURRENT(AMPERES) 200 100 JUNCTION CAPACITANCE(pF) 3 1 60 40 20 10 6 4 2 TJ=25℃ TJ=25℃ 0.3 0.1 0.03 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) Pulse Width=300mS 1% Duty Cycle 1 0.1 0.2 0.4 1 2 4 10 20 40 100 REVERSE VOLTAGE. (V)