19-1516; Rev 0; 7/99
2.5Ω, Quad, SPST,
CMOS Analog Switches
Features
♦ Low On-Resistance (2.5Ω max)
♦ Guaranteed RON Match Between Channels
(0.5Ω max)
♦ Guaranteed RON Flatness over Specified Signal
Range (0.5Ω max)
♦ Rail-to-Rail Signal Handling
♦ Guaranteed Break-Before-Make (MAX4663)
♦ > 2kV ESD Protection per Method 3015.7
♦ +4.5V to +36V Single-Supply Operation
±4.5V to ±20V Dual-Supply Operation
♦ TTL/CMOS-Compatible Control Inputs
Ordering Information
Applications
Reed Relay Replacement
Avionics
Test Equipment
ADC Systems
Communication Systems
Sample-and-Hold Circuits
PBX, PABX Systems
Data Acquisition Systems
PART
TEMP. RANGE
MAX4661CAE
0°C to +70°C
MAX4661CWE
MAX4661CPE
MAX4661EAE
MAX4661EWE
MAX4661EPE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PIN-PACKAGE
16 SSOP
16 Wide SO
16 Plastic DIP
16 SSOP
16 Wide SO
16 Plastic DIP
Ordering Information continued at end of data sheet.
Audio-Signal Routing
Pin Configurations/Functional Diagrams/Truth Tables
TOP VIEW
IN1
1
16
IN2
COM1
2
15
COM2
NC1
3
14
NC2
13
12
V-
4
GND
5
MAX4661
1
16
COM1
2
15
COM2
NO1
3
14
NC2
V+
V-
4
13
V+
VL
GND
5
12
VL
1
16
IN2
COM1
2
15
COM2
NO1
3
14
NO2
V+
V-
4
13
VL
GND
5
12
NC4
6
11
NC3
COM4
7
10
COM3
IN4
8
9
IN3
MAX4662
NO4
6
11
NO3
COM4
7
10
COM3
IN4
8
9
SSOP/SO/DIP
SSOP/SO/DIP
MAX4661
LOGIC
SWITCH
MAX4662
LOGIC
SWITCH
0
1
IN1
IN1
ON
OFF
0
1
IN3
OFF
ON
MAX4663
IN2
NO4
6
11
NC3
COM4
7
10
COM3
IN4
8
9
IN3
SSOP/SO/DIP
LOGIC
MAX4663
SWITCHES
1, 4
SWITCHES
2, 3
0
1
OFF
ON
ON
OFF
SWITCHES SHOWN FOR LOGIC “0” INPUT
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX4661/MAX4662/MAX4663
General Description
The MAX4661/MAX4662/MAX4663 quad analog switches
feature low on-resistance of 2.5Ω max. On-resistance is
matched between switches to 0.5Ω max and is flat
(0.5Ω max) over the specified signal range. Each
switch can handle Rail-to-Rail ® analog signals. Offleakage current is only 5nA max at TA = +85°C. These
analog switches are ideal in low-distortion applications
and are the preferred solution over mechanical relays in
automatic test equipment or applications where current
switching is required. They have lower power requirements, use less board space, and are more reliable
than mechanical relays.
The MAX4661 has four normally closed (NC) switches,
and the MAX4662 has four normally open (NO) switches.
The MAX4663 has two NC and two NO switches, and features guaranteed break-before-make switching.
These devices operate from a single +4.5V to +36V supply or from dual ±4.5V to ±20V supplies. A separate logic
supply pin guarantees TTL/CMOS-logic compatibility
when operating across the entire supply voltage range.
MAX4661/MAX4662/MAX4663
2.5Ω, Quad, SPST,
CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS
V+ to GND ..............................................................-0.3V to +44V
V- to GND ..............................................................+0.3V to -44V
V+ to V-...................................................................-0.3V to +44V
VL to GND .......................................(GND - 0.3V) to (V+ + 0.3V)
All Other Pins to GND (Note 1) .............(V- - 0.3V) to (V+ + 0.3V)
Continuous Current (COM_, NO_, NC_) ........................±200mA
Peak Current (COM_, NO_, NC_)
(pulsed at 1ms, 10% duty cycle)................................ ±300mA
Continuous Power Dissipation (TA = +70°C)
SSOP (derate 7.1mW/°C above +70°C) .......................571mW
Wide SO (derate 9.52mW/°C above +70°C).................762mW
Plastic DIP (derate 10.53mW/°C above +70°C) ...........842mW
Operating Temperature Ranges
MAX466_C_E ......................................................0°C to +70°C
MAX466_E_E ....................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum
current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = +15V, V- = -15V, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
V+
V
ANALOG SWITCH
Input Voltage Range (Note 3)
COM_ to NO or NC_
On-Resistance
COM_ to NO_ or NC_
On-Resistance Match Between
Channels (Notes 3, 4)
VCOM_,
VNO_, VNC_
RON
∆RON
VTA = +25°C
ICOM_ = 10mA,
VNO_ or VNC_ = ±10V TA = TMIN to TMAX
ICOM_ = 10mA,
VNO_ or VNC_= ±10V
0.1
TA = TMIN to TMAX
RFLAT(ON)
Off-Leakage Current
(NO_ or NC_) (Note 6)
INO_, INC_
VCOM_ = ±10V,
– 10V
VNO_ or VNC_= +
COM Off-Leakage Current
(Note 6)
ICOM_(OFF)
TA = +25°C
VCOM_ = ±10V,
– 10V T = T
VNO_ or VNC_ = +
A
MIN to TMAX
COM On-Leakage Current
(Note 6)
ICOM_(ON)
VCOM_ = ±10V,
VNO_ or VNC_= ±10V
or floating
0.1
TA = TMIN to TMAX
TA = TMIN to TMAX
0.5
Ω
Ω
0.6
TA = +25°C
TA = +25°C
2.5
2.7
TA = +25°C
COM_ to NO_ or NC_
On-Resistance Flatness
(Notes 3, 5)
ICOM_ = 10mA; VNO_
or VNC_ = -5V, 0, 5V
1.7
0.5
Ω
0.6
-0.5
0.01
-5
-0.5
5
0.01
-5
TA = +25°C
-1
TA = TMIN to TMAX
-20
0.5
0.5
5
0.01
nA
nA
1
nA
20
LOGIC INPUT
Input Current with Input Voltage
High
IIN_H
IN_ = 2.4V, all others = 0.8V
-0.5
0.001
0.5
µA
Input Current with Input Voltage
Low
IIN_L
IN_ = 0.8V, all others = 2.4V
-0.5
0.001
0.5
µA
Logic Input Voltage High
VIN_H
Logic Input Voltage Low
VIN_L
2
2.4
_______________________________________________________________________________________
V
0.8
V
2.5Ω, Quad, SPST,
CMOS Analog Switches
(V+ = +15V, V- = -15V, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
±20.0
V
POWER SUPPLY
Power-Supply Range
±4.5
Positive Supply Current
I+
VIN = 0 or 5V
Negative Supply Current
I-
VIN = 0 or 5V
Logic Supply Current
IL
VIN = 0 or 5V
IGND
VIN = 0 or 5V
Ground Current
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
-0.5
0.001
-5
-0.5
5
0.001
-5
-0.5
0.5
5
0.001
-5
-0.5
0.5
0.5
5
0.001
-5
0.5
5
µA
µA
µA
µA
SWITCH DYNAMIC CHARACTERISTICS
Turn-On Time
tON
VCOM_ = ±10V,
Figure 2
TA = +25°C
Turn-Off Time
tOFF
VCOM_ = ±10V,
Figure 2
TA = +25°C
Break-Before-Make Time
(MAX4663 only)
Charge Injection
tOPEN
Q
130
TA = TMIN to TMAX
100
175
300
TA = TMIN to TMAX
VCOM_ = ±10V, Figure 3, TA = +25°C
275
400
5
ns
ns
30
ns
CL = 1.0nF, VGEN = 0, RGEN = 0,
Figure 4
300
pC
Off-Isolation (Note 7)
VISO
RL = 50Ω, CL = 5pF, f = 1MHz,
Figure 5
-56
dB
Crosstalk (Note 8)
VCT
RL = 50Ω, CL = 5pF, f = 1MHz,
Figure 6
-59
dB
NC_ or NO_ Capacitance
COFF
f = 1MHz, Figure 7
55
pF
COM_ Off-Capacitance
CCOM
f = 1MHz, Figure 7
55
pF
On-Capacitance
CCOM
f = 1MHz, Figure 8
250
pF
_______________________________________________________________________________________
3
MAX4661/MAX4662/MAX4663
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)
MAX4661/MAX4662/MAX4663
2.5Ω, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply
(V+ = +12V, V- = 0, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
V+
V
ANALOG SWITCH
Input Voltage Range (Note 3)
COM_ to NO or NC_
On-Resistance
COM_ to NO_ or NC_
On-Resistance Match Between
Channels (Notes 3, 4)
COM_ to NO_ or NC_
On-Resistance Flatness
(Notes 3, 5)
VCOM_, VNO_,
VNC_
RON
∆RON
RFLAT(ON)
GND
ICOM_ = 10mA,
VNO_ or VNC_ = 10V
ICOM_ = 10mA,
VNO_ or = VNC_= 10V
ICOM_ = 10mA; VNO_
or VNC_ = 3V, 6V, 9V
TA = +25°C
3
TA = TMIN to TMAX
4
5
TA = +25°C
0.03
TA = TMIN to TMAX
0.4
Ω
Ω
0.5
TA = +25°C
0.1
TA = TMIN to TMAX
0.7
Ω
0.8
Off-Leakage Current
(NO_ or NC_) (Notes 6, 9)
INO_
INC_
VCOM_ = 1V, 10V;
VNO_ or VNC_ = 10V,
1V
TA = +25°C
COM Off-Leakage Current
(Notes 6, 9)
ICOM_(OFF)
VNO_ or VNC_ = 10V,
1V; VCOM_ = 1V, 10V
TA = +25°C
TA = TMIN to TMAX
-5
COM On-Leakage Current
(Notes 6, 9)
VCOM_ = 1V ,10V;
VNO_ or VNC_ = 1V,
10V, or floating
TA = +25°C
-1
ICOM_(ON)
TA = TMIN to TMAX
-20
-0.5
0.01
0.5
nA
TA = TMIN to TMAX
-5
-0.5
5
0.01
0.5
5
0.01
nA
1
nA
20
LOGIC INPUT
Input Current with Input Voltage
High
IIN_H
IN_ = 2.4V, all others = 0.8V
-0.5
0.001
0.5
µA
Input Current with Input Voltage
Low
IIN_L
IN_ = 0.8V, all others = 2.4V
-0.5
0.001
0.5
µA
Logic Input Voltage High
VIN_H
Logic Input Voltage Low
VIN_L
2.4
V
0.8
V
+36.0
V
POWER SUPPLY
Power-Supply Range
+4.5
Positive Supply Current
I+
VIN = 0 or 5V
Logic Supply Current
IL
VIN = 0 or 5V
IGND
VIN = 0 or 5V
Ground Current
4
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
-0.5
0.001
-5
-0.5
5
0.001
-5
-0.5
0.5
0.5
5
0.001
-5
_______________________________________________________________________________________
0.5
5
µA
µA
µA
2.5Ω, Quad, SPST,
CMOS Analog Switches
(V+ = +12V, V- = 0, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
200
400
UNITS
SWITCH DYNAMIC CHARACTERISTICS
Turn-On Time (Note 3)
tON
VCOM_ = 10V,
Figure 2
TA = +25°C
Turn-Off Time (Note 3)
tOFF
VCOM_ = 10V,
Figure 2
TA = +25°C
Break-Before-Make Time
(MAX4663 only) (Note 3)
Charge Injection
tOPEN
Q
Crosstalk (Note 8)
VCT
TA = TMIN to TMAX
500
100
TA = TMIN to TMAX
VCOM_ = 10V, Figure 3, TA = +25°C
250
350
5
ns
ns
125
ns
CL = 1.0nF, VGEN = 0, RGEN = 0,
Figure 4
20
pC
RL = 50Ω, CL = 5pF, f = 1MHz,
Figure 6
-60
dB
85
pF
NC_ or NO_ Capacitance
COFF
f = 1MHz, Figure 7
COM Off-Capacitance
CCOM
f = 1MHz, Figure 7
85
pF
On-Capacitance
CCOM
f = 1MHz, Figure 8
140
pF
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆RON = RON(MAX) - RON(MIN).
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7: Off-isolation = 20log10 [VCOM / (VNC or VNO)], VCOM = output, VNC or VNO = input to off switch.
Note 8: Between any two switches.
Note 9: Leakage testing at single supply is guaranteed by testing with dual supplies.
_______________________________________________________________________________________
5
MAX4661/MAX4662/MAX4663
ELECTRICAL CHARACTERISTICS—Single Supply (continued)
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
ON-RESISTANCE vs. VCOM AND
TEMPERATURE (DUAL SUPPLIES)
TA = +85°C
7
1.50
6
RON (Ω)
1.75
2.5
1.25
2.0
1.00
1.5
0.75
1.0
0.50
V+, V- = ±15V
TA = +25°C
-15
-10
-5
0
5
10
15
20
1
V+, V- = ±15V
0
-15
-10
-5
0
5
10
15
0
2
4
6
8 10 12 14 16 18 20 22 24
VCOM (V)
VCOM (V)
ON-RESISTANCE vs. VCOM AND
TEMPERATURE (SINGLE SUPPLY)
ON/OFF-LEAKAGE CURRENT
vs. TEMPERATURE
CHARGE INJECTION
vs. VCOM
TA = +25°C
1.50
300
ON-LEAKAGE
200
100
LEAKAGE (pA)
TA = -40°C
10
1
-100
1m
-200
0.1m
2
3
4
5
6
7
8
9 10 11 12
-40
-20
0
VCOM (V)
20
40
60
80
0
V+ = +15V
V- = -15V
FREQUENCY RESPONSE
MAX4661/2/3-08
-10
-0
-30
LOSS (dB)
100
I+
I-
1
-90
ON-PHASE
-40
-180
-50
-270
-60
V+ = +15V
V- = -15V
INPUT = OdBm
50Ω IN AND OUT
-80
0.01
-90
0.001
-100
-40
-20
0
20
40
60
TEMPERATURE (°C)
80
100
-360
OFF-ISOLATION
-70
0.1
180
90
ON-RESPONSE
-20
1k
10
5
VCOM (V)
0
MAX4661/2/3-07
100k
I+, I- (nA)
-10 -5
TEMPERATURE (°C)
POWER-SUPPLY CURRENT
vs. TEMPERATURE
10k
-20 -15
100
0.1
1
10
-450
-540
-630
-720
100
FREQUENCY (MHz)
_______________________________________________________________________________________
PHASE (degrees)
0
1
V- = GND
V+ = 12V
OFF-LEAKAGE
0.01
V+ = +12V
V- = GND
V- = -15V
V+ = +15V
100
0
0.1
1.00
MAX4661/2/3-06
1k
2.50
2.00
V+ = +15V
V- = -15V
Q (pC)
3.00
10k
400
MAX4661/2/3-05
3.50
100k
MAX4661/2/3-04
TA = +85°C
0
V+ = 24V
2
VCOM (V)
4.00
0.50
V+ = 12V
3
TA = -40°C
0
-20
5
4
0.25
V+, V- = ±20V
0
V+ = 5V
8
3.0
0.5
6
9
3.5
RON (Ω)
RON (Ω)
V+, V- = ±5V
2.25
2.00
10
MAX4661/2/3-02
4.5
4.0
2.50
MAX4661/2/3-01
5.0
ON-RESISTANCE vs. VCOM
(SINGLE SUPPLY)
MAX4661/2/3-03
ON-RESISTANCE vs. VCOM
(DUAL SUPPLIES)
RON (Ω)
MAX4661/MAX4662/MAX4663
2.5Ω, Quad, SPST,
CMOS Analog Switches
10
15
20
2.5Ω, Quad, SPST,
CMOS Analog Switches
PIN
NAME
FUNCTION
MAX4661
MAX4662
MAX4663
1, 16, 9, 8
1, 16, 9, 8
1, 16, 9, 8
IN1, IN2,
IN3, IN4
2, 15,
10, 7
2, 15,
10, 7
2, 15,
10, 7
COM1, COM2,
COM3, COM4
3, 14, 11, 6
—
—
NC1, NC2,
NC3, NC4
Analog Switch Normally Closed Terminals
—
3, 14, 11, 6
—
NO1, NO2,
NO3, NO4
Analog Switch Normally Open Terminals
—
—
3, 6
NO1, NO4
Analog Switch Normally Open Terminals
—
—
14, 11
NC2, NC3
Analog Switch Normally Closed Terminals
4
4
4
V-
5
5
5
GND
12
12
12
VL
Logic-Supply Input
13
13
13
V+
Positive Analog Supply Input
Logic-Control Digital Inputs
Analog Switch Common Terminals
Negative Analog Supply-Voltage Input. Connect to GND for singlesupply operation.
Ground
Applications Information
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maximum ratings because stresses beyond the listed ratings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, NO, or COM. If power-supply sequencing
is not possible, add two small-signal diodes (D1, D2)
in series with the supply pins and a Schottky diode
between V+ and VL for overvoltage protection (Figure
1). Adding diodes reduces the analog signal range to
one diode drop below V+ and one diode drop above V-,
but does not affect the devices’ low switch resistance
and low leakage characteristics. Device operation is
unchanged, and the difference between V+ and Vshould not exceed 44V.
Above 5MHz, circuit board layout becomes critical and
it becomes difficult to characterize the response of the
switch independent of the circuit. The graphs shown in
the Typical Operating Characteristics were taken using
a 50Ω source and load connected with BNC connectors to a circuit board deemed “average”; that is,
designed with isolation in mind, but not using stripline
or other special RF circuit techniques. For critical applications above 5MHz, use the MAX440, MAX441, and
MAX442, which are fully characterized up to 160MHz.
+15V
D1
*
*
*
*
MAX4661
MAX4662
MAX4663
NO_
COM_
Off-Isolation at High Frequencies
In 50Ω systems, the high-frequency on-response of
these parts extends from DC to above 100MHz with a
typical loss of -2dB. When the switch is turned off, however, it behaves like a capacitor and off-isolation
decreases with increasing frequency. (Above 300MHz,
the switch actually passes more signal turned off than
turned on.) This effect is more pronounced with higher
source and load impedances.
VL
V+
VD2
* INTERNAL PROTECTION DIODES
-15V
Figure 1. Overvoltage Protection Using External Blocking
Diodes
_______________________________________________________________________________________
7
MAX4661/MAX4662/MAX4663
Pin Description
MAX4661/MAX4662/MAX4663
2.5Ω, Quad, SPST,
CMOS Analog Switches
+5V
LOGIC
INPUT
t r < 20ns
t f < 20ns
+3V
50%
SWITCH V COM_
INPUT
0
MAX4661
MAX4662
MAX4663
+15V
VL
COM_
IN_
VO
0
0.9V0
0.9V0
LOGIC
INPUT
GND
V-
0
-15V
t ON
VO
RL
100Ω
t OFF
SWITCH
OUTPUT
SWITCH
OUTPUT
V+
NO_
OR NC_
CL
35pF
REPEAT TEST FOR EACH SWITCH. FOR LOAD
CONDITIONS, SEE Electrical Characteristics.
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
RL
VO = VCOM
RL + RON
LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES
THAT HAVE THE OPPOSITE LOGIC SENSE.
(
)
Figure 2. Switching-Time Test Circuit
+15V
MAX4663
VCOM1
VCOM2
COM1
V+
GND
NO
VOUT1
NC
COM2
VOUT2
RL2
IN1, 2
LOGIC
INPUT
LOGIC
INPUT
CL2
CL1
50%
0V
SWITCH
OUTPUT 1
(VOUT1)
0.9 · V0UT1
0V
SWITCH
OUTPUT 2
(VOUT2)
V-15V
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
RL1
+3V
RL = 100Ω
CL = 35pF
0.9 · VOUT2
0V
tD
Figure 3. Break-Before-Make Interval (MAX4663 only)
8
_______________________________________________________________________________________
tD
2.5Ω, Quad, SPST,
CMOS Analog Switches
RGEN
+5V
+15V
VL
V+
MAX4661/MAX4662/MAX4663
MAX4661
MAX4662
MAX4663
∆VO
VO
NC OR
NO
COM
VO
VIN
CL
V GEN
GND
OFF
-15V
VIN
VIN = +3V
OFF
ON
V-
IN
ON
OFF
OFF
Q = (∆V O )(C L )
VIN DEPENDS ON SWITCH CONFIGURATION;
INPUT POLARITY DETERMINED BY SENSE OF SWITCH.
Figure 4. Charge-Injection Test Circuit
+15V
+5V
V+
VL
SIGNAL
GENERATOR 0dBm
MAX4661
MAX4662
MAX4663
SIGNAL
GENERATOR 0dBm
+15V
+5V
V+
VL
COM1
MAX4661
MAX4662
MAX4663
N_1
50Ω
COM
IN
COM
ANALYZER
NC OR NO
GND
3.0V
V-
0 OR 3.0V
COM2
N_2
ANALYZER
RL
IN2
IN1
0 OR 3.0V
GND
RL
-15V
-15V
Figure 5. Off-Isolation Test Circuit
N.C.
V-
Figure 6. Crosstalk Test Circuit
_______________________________________________________________________________________
9
MAX4661/MAX4662/MAX4663
2.5Ω, Quad, SPST,
CMOS Analog Switches
+15V
+5V
V+
VL
COM
MAX4661
MAX4662
MAX4663
+15V
+5V
V+
VL
COM
MAX4661
MAX4662
MAX4663
CAPACITANCE
METER
IN
CAPACITANCE
METER
IN
0 OR
3.0V
GND
V-
GND
Figure 7. Switch Off-Capacitance Test Circuit
Figure 8. Switch On-Capacitance Test Circuit
Chip Information
Ordering Information (continued)
10
TEMP. RANGE
0°C to +70°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PIN-PACKAGE
16 SSOP
16 Wide SO
16 Plastic DIP
16 SSOP
16 Wide SO
16 Plastic DIP
16 SSOP
16 Wide SO
16 Plastic DIP
16 SSOP
16 Wide SO
16 Plastic DIP
V-
-15V
-15V
PART
MAX4662CAE
MAX4662CWE
MAX4662CPE
MAX4662EAE
MAX4662EWE
MAX4662EPE
MAX4663CAE
MAX4663CWE
MAX4663CPE
MAX4663EAE
MAX4663EWE
MAX4663EPE
0 OR
3.0V
NC OR NO
NC OR NO
f = 1MHz
f = 1MHz
TRANSISTOR COUNT: 108
______________________________________________________________________________________
2.5Ω, Quad, SPST,
CMOS Analog Switches
SSOP.EPS
______________________________________________________________________________________
11
MAX4661/MAX4662/MAX4663
Package Information
2.5Ω, Quad, SPST,
CMOS Analog Switches
SOICW.EPS
MAX4661/MAX4662/MAX46663
Package Information (continued)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
工商网监
湘ICP备2023018690号
