19-1105; Rev 0; 8/96
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
________________________Applications
____________________________Features
♦ +4.5V to +5.5V Single-Supply Operation
♦ Ultra-Low Supply Current:
0.8mA while Operating
2.5µA in Shutdown Mode
♦ Ultra-Small 16-Pin QSOP Package
♦ Ground to VDD Reference Input Range
♦ Output Buffer Amplifiers Swing Rail to Rail
♦ 10MHz Serial Interface Compatible with SPI, QSPI
(CPOL = CPHA = 0 or CPOL = CPHA = 1), and
Microwire
♦ Double-Buffered Registers for Synchronous
Updating
♦ Serial Data Output for Daisy Chaining
♦ Power-On Reset Clears Serial Interface and Sets
All Registers to Zero
♦ Software Shutdown
♦ Software-Programmable Logic Output (µC I/O
Extender)
♦ Asynchronous Hardware Clear Resets All Internal
Registers to Zero
______________Ordering Information
Digital Gain and Offset Adjustments
Programmable Attenuators
Programmable Current Sources
Portable Instruments
__________________Pin Configuration
TOP VIEW
OUTB 1
16 OUTC
OUTA 2
15 OUTD
14 AGND
REF 3
UPO 4
MAX534
PDE 5
13 VDD
12 DGND
LDAC 6
11 DIN
CLR 7
10 SCLK
DOUT 8
9
CS
PART
TEMP. RANGE
PIN-PACKAGE
MAX534ACPE
MAX534BCPE
MAX534ACEE
MAX534BCEE
MAX534BC/D
MAX534AEPE
MAX534BEPE
MAX534AEEE
MAX534BEEE
MAX534AMJE
MAX534BMJE
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
-55°C to +125°C
16 Plastic DIP
16 Plastic DIP
16 QSOP
16 QSOP
Dice*
16 Plastic DIP
16 Plastic DIP
16 QSOP
16 QSOP
16 CERDIP**
16 CERDIP**
INL
(LSB)
±1
±2
±1
±2
±2
±1
±2
±1
±2
±1
±2
*Dice are tested at TA = +25°C.
**Contact factory for availability and processing to MIL-STD-883.
Functional Diagram appears at end of data sheet.
DIP/QSOP
SPI and QSPI are trademarks of Motorola, Inc. Microwire is a trademark of National Semiconductor Corp.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800
MAX534
_______________General Description
The MAX534 serial-input, voltage-output, 8-bit quad digital-to-analog converter (DAC) operates from a single
+4.5V to +5.5V supply. Internal precision buffers swing
rail to rail, and the reference input range includes both
ground and the positive rail. The MAX534 features a
2.5µA shutdown mode.
The serial interface is double buffered: a 12-bit input
shift register is followed by four 8-bit buffer registers and
four 8-bit DAC registers. The 12-bit serial word consists
of eight data bits and four control bits (for DAC selection
and special programming commands). Both the input
and DAC registers can be updated independently or
simultaneously with a single software command. Two
additional asynchronous control pins, LDAC and CLR,
provide simultaneous updating or clearing of the input
and DAC registers.
The interface is compatible with SPI™, QSPI™ (CPOL =
CPHA = 0 or CPOL = CPHA = 1), and Microwire™. A
buffered data output allows daisy chaining of serial
devices.
In addition to 16-pin DIP and CERDIP packages, the
MAX534 is available in a 16-pin QSOP that occupies the
same area as an 8-pin SO.
For operation guaranteed to 2.7V, see the MAX533
data sheet.
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
ABSOLUTE MAXIMUM RATINGS
VDD to DGND ..............................................................-0.3V, +6V
VDD to AGND...............................................................-0.3V, +6V
Digital Input Voltage to DGND ....................................-0.3V, +6V
Digital Output Voltage to DGND....................-0.3V, (VDD + 0.3V)
AGND to DGND ..................................................................±0.3V
REF ................................................................-0.3V, (VDD + 0.3V)
OUT_ ...........................................................................-0.3V, VDD
Maximum Current into Any Pin............................................50mA
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 10.53mW/°C above +70°C) .........842mW
QSOP (derate 8.3mW/°C above +70°C) .....................667mW
CERDIP (derate 10.00mW/°C above +70°C) ..............800mW
Operating Temperature Ranges
MAX534 _ C_ E ..................................................0°C to +70°C
MAX534 _ E_ E ...............................................-40°C to +85°C
MAX534 _ MJE .............................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = +4.5V to +5.5V, VREF = 4.096V, AGND = DGND = 0V, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted.
Typical values are at VDD = +5V and TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
8
Bits
STATIC ACCURACY
Resolution
MAX534A
±1
MAX534B
±2
Integral Nonlinearity
(Note 1)
INL
Differential Nonlinearity (Note 1)
DNL
Guaranteed monotonic (all codes)
±1.0
LSB
Zero-Code Error
ZCE
Code = 00 hex
±20
mV
1
LSB
Zero-Code-Error Supply
Rejection
Code = 00 hex, VDD = 4.5V to 5.5V
Zero-Code Temperature
Coefficient
Code = 00 hex
Full-Scale Error
Code = FF hex
Full-Scale Error Supply
Rejection
Code = FF hex, VDD = 4.5V to 5.5V
Full-Scale Temperature
Coefficient
Code = FF hex
±10
LSB
µV/°C
±30
mV
1
LSB
±10
µV/°C
REFERENCE INPUTS
Input Voltage Range
0
Input Resistance
322
Input Capacitance
460
VDD
V
598
kΩ
10
pF
Channel-to-Channel Isolation
(Note 2)
-60
dB
AC Feedthrough
(Note 3)
-60
dB
DAC OUTPUTS
Output Voltage Range
RL = open
Load Regulation
Code = FF hex, measured with IL = 0mA to
1.6mA
2
0
_______________________________________________________________________________________
VREF
V
0.156
LSB/mA
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
(VDD = +4.5V to +5.5V, VREF = 4.096V, AGND = DGND = 0V, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted.
Typical values are at VDD = +5V and TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL INPUTS
Input High Voltage
VIH
Input Low Voltage
VIL
0.7VDD
Input Current
IIN
VIN = 0V or VDD
Input Capacitance
CIN
(Note 4)
Output High Voltage
VOH
ISOURCE = 0.2mA
Output Low Voltage
VOL
ISINK = 1.6mA
V
0.3VDD
V
±1.0
µA
10
pF
DIGITAL OUTPUTS
VDD - 0.5
V
0.4
V
DYNAMIC PERFORMANCE
Voltage-Output Slew Rate
CODE = FF hex
0.6
V/µs
Output Settling Time
To 1/2LSB, from code 00 to code FF hex
(Note 5)
8
µs
Digital Feedthrough and
Crosstalk
VREF = 0V, code 00 to code FF hex (Note 6)
5
nV-s
Digital-to-Analog Glitch Impulse
Code 80 hex to code 7F hex
50
nV-s
Signal-to-Noise Plus
Distortion Ratio
VREF = 4Vp-p at 1kHz, code = FF hex
80
VREF = 4Vp-p at 10kHz
70
VREF = 0.5Vp-p, 3dB bandwidth
380
kHz
60
µVRMS
SINAD
Multiplying Bandwidth
Wideband Amplifier Noise
dB
POWER SUPPLIES
Power-Supply Voltage
Supply Current
VDD
IDD
4.5
5.5
MAX534C/E
0.8
1.3
MAX534M
0.8
1.5
2.5
10
Shutdown Current
V
mA
µA
TIMING CHARACTERISTICS
(VDD = +4.5V to +5.5V, VREF = 4.096V, AGND = DGND = 0V, CDOUT = 100pF, TA = TMIN to TMAX, unless otherwise noted.
Typical values are at VDD = +5V and TA = +25°C.)
PARAMETER
SYMBOL
VDD Rise to CS Fall Setup Time
(Note 4)
tVDCS
LDAC Pulse Width Low
tLDAC
CS Rise to LDAC Fall Setup
Time (Note 7)
tCLL
CLR Pulse Width Low
tCLW
CS Pulse Width High
tCSW
CONDITIONS
MIN
TYP
MAX
MAX534C/E
50
MAX534M
60
MAX534C/E
40
20
MAX534M
50
25
MAX534C/E
40
MAX534M
50
MAX534C/E
40
20
MAX534M
50
25
MAX534C/E
90
MAX534M
100
UNITS
µs
ns
ns
ns
ns
_______________________________________________________________________________________
3
MAX534
ELECTRICAL CHARACTERISTICS (continued)
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
TIMING CHARACTERISTICS (continued)
(VDD = +4.5V to +5.5V, VREF = 4.096V, AGND = DGND = 0V, CDOUT = 100pF, TA = TMIN to TMAX, unless otherwise noted.
Typical values are at VDD = +5V and TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SERIAL-INTERFACE TIMING
SCLK Clock Frequency (Note 8)
fCLK
SCLK Pulse Width High
tCH
SCLK Pulse Width Low
tCL
CS Fall to SCLK Rise Setup
Time
tCSS
SCLK Rise to CS Rise Hold Time
tCSH
DIN to SCLK Rise to Setup Time
tDS
DIN to SCLK Rise to Hold Time
tDH
SCLK Rise to DOUT Valid
Propagation Delay (Note 9)
tDO1
SCLK Fall to DOUT Valid
Propagation Delay (Note 10)
tDO2
SCLK Rise to CS Fall Delay
tCS0
CS Rise to SCLK Rise Setup
Time
tCS1
MAX534C/E
10
MAX534M
8.3
MAX534C/E
40
MAX534M
50
MAX534C/E
40
MAX534M
50
MAX534C/E
40
MAX534M
50
ns
ns
ns
0
MAX534C/E
40
MAX534M
50
ns
ns
0
ns
MAX534C/E
200
MAX534M
230
MAX534C/E
210
MAX534M
250
MAX534C/E
40
MAX534M
50
MAX534C/E
40
MAX534M
50
MHz
ns
ns
ns
ns
Note 1: INL and DNL are measured with RL referenced to ground. Nonlinearity is measured from the first code that is greater than
or equal to the maximum offset specification to code FF hex (full scale). See DAC Linearity and Voltage Offset section.
Note 2: VREF = 4Vp-p, 10kHz. Channel-to-channel isolation is measured by setting one DAC’s code to FF hex and setting all other
DAC’s codes to 00 hex.
Note 3: VREF = 4Vp-p, 10kHz. DAC code = 00 hex.
Note 4: Guaranteed by design, not production tested.
Note 5: Output settling time is measured from the 50% point of the rising edge of CS to 1/2LSB of VOUT’s final value.
Note 6: Digital crosstalk is defined as the glitch energy at any DAC output in response to a full-scale step change on any other
DAC.
Note 7: If LDAC is activated prior to CS’s rising edge, it must stay low for tLDAC or longer after CS goes high.
Note 8: When DOUT is not used. If DOUT is used, fCLK max is 4MHz, due to the SCLK to DOUT propagation delay.
Note 9: Serial data clocked out at SCLK’s rising edge (measured from 50% of the clock edge to 20% or 80% of VDD).
Note 10: Serial data clocked out at SCLK’s falling edge (measured from 50% of the clock edge to 20% or 80% of VDD).
4
_______________________________________________________________________________________
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
0.75
0.50
0.25
0
800
4.0
3.5
3.0
VREF = 5V
DAC CODE = FF HEX
LOAD TO GND
2.5
1
2
4
3
5
6
7
8
600
DAC CODE = 00 HEX
400
200
VREF = 4.5V
0
2.0
0
DAC OUTPUT SINK CURRENT (mA)
2
4
6
8
12
10
SHUTDOWN SUPPLY CURRENT vs.
TEMPERATURE
5
-55 -35 -15
5
25
65 85 105 125
45
TEMPERATURE (°C)
DAC OUTPUT SOURCE CODE (mA)
SUPPLY CURRENT vs.
REFERENCE VOLTAGE
1000
MAX534-TOC4
3
ALL DAC CODES = FF HEX
800
SUPPLY CURRENT (µA)
0
DAC CODE = FF HEX
MAX534-TOC3
MAX534-TOC2
4.5
3
2
1
MAX534-TOC6
1.00
1000
SUPPLY CURRENT (µA)
DAC FULL-SCALE OUTPUT VOLTAGE (V)
1.25
5.0
MAX534-TOC1
VREF = 5V
DAC CODE = 00 HEX
LOAD TO VDD
SHUTDOWN SUPPLY CURRENT (µA)
DAC ZERO-CODE OUTPUT VOLTAGE (V)
1.50
SUPPLY CURRENT vs.
TEMPERATURE
DAC FULL-SCALE OUTPUT VOLTAGE vs.
OUTPUT SOURCE CURRENT
DAC ZERO-CODE OUTPUT VOLTAGE vs.
OUTPUT SINK CURRENT
600
ALL DAC CODES = 00 HEX
400
200
0
0
-55 -35 -15
5
25
45
65 85 105 125
TEMPERATURE (°C)
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
REFERENCE VOLTAGE (V)
_______________________________________________________________________________________
5
MAX534
__________________________________________Typical Operating Characteristics
(VDD = +5V, TA = +25°C, unless otherwise noted.)
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
______________________________________________________________Pin Description
6
PIN
NAME
1
OUTB
DAC B Voltage Output
FUNCTION
2
OUTA
DAC A Voltage Output
3
REF
Reference-Voltage Input
4
UPO
Software-Programmable Logic Output
5
PDE
Power-Down Enable. Must be high to allow software shutdown mode.
6
LDAC
Load DAC Input (active low). Driving this asynchronous input low (level sensitive) transfers the contents
of each input latch to its respective DAC latch.
7
CLR
Clear DAC Input (active low). Driving CLR low asynchronously clears the input and DAC registers, and
sets all DAC outputs to zero.
8
DOUT
Serial Data Output. Sinks and sources current. Data at DOUT can be clocked out on the rising or falling
edge of SCLK (Table 1).
9
CS
Chip-Select Input (active low). Data is shifted in and out when CS is low. Programming commands are
executed when CS returns high.
10
SCLK
Serial Clock Input. Data is clocked in on the rising edge and clocked out on the falling (default) or rising
edge (A0 = A1 = 1, see Table 1).
11
DIN
12
DGND
Serial Data Input. Data is clocked in on the rising edge of SCLK.
13
VDD
14
AGND
Analog Ground
15
OUTD
DAC D Voltage Output
16
OUTC
DAC C Voltage Output
Digital Ground
Power Supply, +4.5V to +5.5V
_______________________________________________________________________________________
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
MAX534
INSTRUCTION
EXECUTED
CS
•••
•••
SCLK
•••
DIN
A1 A0 C1 C0
A1 A0 C1 C0
D7 D6 D5 D4 D3 D2 D1 D0
MSB
D7 D6 D5 D4 D3 D2
MSB
LSB
LSB
DACD
DACA
•••
DOUT
MODE 1
A1
A0 C1 C0
D7
D6 D5 D4 D3 D2 D1 D0
A1
A1
A0 C1 C0
DATA FROM PREVIOUS DATA INPUT
DOUT
MODE 0
(DEFAULT)
D1 D0
D6 D5 D4 D3 D2 D1 D0
D7
A1
DATA FROM PREVIOUS DATA INPUT
•••
A1 A0 C1 C0
D7
D6 D5 D4 D3 D2 D1 D0
A1
A1
A0 C1 C0
D6 D5 D4 D3 D2 D1 D0
D7
A1
Figure 1. 3-Wire Interface Timing
CS
tCSW
tCS0
tCSS
tCH
tCSH
tCP
tCS1
tCL
SCLK
tDS
tDH
DIN
tD02
tD01
DOUT
tCLL
tLDAC
LDAC
Figure 2. Detailed Serial-Interface Timing Diagram
_______________________________________________________________________________________
7
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
_______________Detailed Description
Serial Interface
At power-on, the serial interface and all digital-toanalog converters (DACs) are cleared and set to code
zero. The serial data output (DOUT) is set to transition
on SCLK’s falling edge.
The MAX534 communicates with microprocessors
through a synchronous, full-duplex, 3-wire interface
(Figure 1). Data is sent MSB first and can be transmitted in one 4-bit and one 8-bit (byte) packet or in one
12-bit word. If a 16-bit word is used, the first four bits
are ignored. A 4-wire interface adds a line for LDAC
and allows asynchronous updating. The serial clock
(SCLK) synchronizes the data transfer. Data is transmitted and received simultaneously.
Figure 2 shows the detailed serial-interface timing.
Please note that the clock should be low if it is stopped
between updates. DOUT does not go into a highimpedance state if the clock idles or CS is high.
Serial data is clocked into the data registers in MSB-first
format, with the address and configuration information
preceding the actual DAC data. Data is clocked in on
SCLK’s rising edge while CS is low. Data at DOUT is
clocked out 12 clock cycles later, either at SCLK’s falling
edge (default or mode 0) or rising edge (mode 1).
Chip select (CS) must be low to enable the DAC. If CS
is high, the interface is disabled and DOUT remains
unchanged. CS must go low at least 40ns before the
first rising edge of the clock pulse to properly clock in
the first bit. With CS low, data is clocked into the
MAX534’s internal shift register on the rising edge of
the external serial clock. Always clock in the full 12 bits
because each time CS goes high the bits currently in
the input shift register are interpreted as a command.
SCLK can be driven at rates up to 10MHz.
Serial Input Data Format and Control Codes
The 12-bit serial input format shown in Figure 3 comprises two DAC address bits (A1, A0), two control bits
(C1, C0), and eight bits of data (D7...D0).
The 4-bit address/control code configures the DAC as
shown in Table 1.
Load Input Register, DAC Registers Unchanged
(Single Update Operation)
A1 A0
Address
C1
0
C0
1
D7
D6
D5
D4 D3 D2
8-Bit Data
D1
D0
(LDAC = H)
When performing a single update operation, A1 and A0
select the respective input register. At the rising edge
of CS, the selected input register is loaded with the current shift-register data. All DAC outputs remain
unchanged. This preloads individual data in the input
register without changing the DAC outputs.
Load Input and DAC Registers
A1 A0
Address
C1
1
C0
1
D7
D6
D5
D4 D3 D2
8-Bit Data
D1
D0
(LDAC = H)
This command directly loads the selected DAC register
at CS’s rising edge. A1 and A0 set the DAC address.
Current shift-register data is placed in the selected
input and DAC registers.
For example, to load all four DAC registers simultaneously
with individual settings (DAC A = 1V, DAC B = 2V,
DAC C = 3V, and DAC D = 4V), four commands are
required. First, perform three single input register
update operations for DACs A, B, and C (C1 = 0). The
final command loads input register D and updates all
four DAC registers from their respective input registers.
Software “LDAC ” Command
THIS IS THE FIRST BIT SHIFTED IN
MSB
DOUT
A1 A0 C1 C0 D7 D6
CONTROL AND
ADDRESS BITS
...
LSB
D1
D0
8-BIT DAC DATA
DIN
A1
A0
C1
C0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
0
0
x
x
x
x
x
x
x
x
(LDAC = 1)
When this command is initiated, all DAC registers are
updated with the contents of their respective input registers at CS’s rising edge. With the exception of using
CS to execute, this performs the same function as the
asynchronous LDAC.
Figure 3. Serial Input Format
8
_______________________________________________________________________________________
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
MAX534
Table 1. Serial-Interface Programming Commands
12-BIT SERIAL WORD
A1
A0
C1
C0
D7 . . . . . . . . D0
LDAC
0
0
1
1
0
1
0
1
0
0
0
0
1
1
1
1
8-bit DAC data
8-bit DAC data
8-bit DAC data
8-bit DAC data
1
1
1
1
Load input register A; all DAC outputs unchanged.
Load input register B; all DAC outputs unchanged.
Load input register C; all DAC outputs unchanged.
Load input register D; all DAC outputs unchanged.
0
0
1
1
0
1
0
1
1
1
1
1
1
1
1
1
8-bit DAC data
8-bit DAC data
8-bit DAC data
8-bit DAC data
1
1
1
1
Load input register A; all DAC outputs updated
Load input register B; all DAC outputs updated
Load input register C; all DAC outputs updated
Load input register D; all DAC outputs updated.
0
1
0
0
XXXXXXXX
1
Software LDAC commands. Update all DACs from
their respective input registers. Also bring the part out
of shutdown mode.
1
0
0
0
8-bit DAC data
X
Load all DACs with shift-register data. Also bring the
part out of shutdown mode.
1
1
0
0
XXXXXXXX
X
Software shutdown (provided PDE is high)
0
0
1
0
XXXXXXXX
X
UPO goes low.
0
1
1
0
XXXXXXXX
X
UPO goes high.
0
0
0
0
XXXXXXXX
X
No operation (NOP); shift data in shift registers.
1
1
1
0
XXXXXXXX
X
Set DOUT phase—SCLK rising (mode 1). DOUT
clocked out on rising edge of SCLK. All DACs updated
from their respective input registers.
1
0
1
0
XXXXXXXX
X
Set DOUT phase—SCLK falling (mode 0). DOUT
clocked out on falling edge of SCLK. All DACs updated from their respective registers (default).
FUNCTION
Load All DACs with Shift-Register Data
A1
1
A0
0
C1
0
C0
0
D7
D6
D5
D4 D3 D2
8-Bit Data
D1
D0
User-Programmable Output (UPO)
A1 A0 C1 C0 D7 D6 D5 D4 D3 D2 D1 D0
0
0
(LDAC = X)
When this command is initiated, all four DAC registers
are updated with shift-register data. This command
allows all DACs to be set to any analog value within the
reference range. It can be used to substitute CLR if
code 00 hex is programmed, which clears all DACs.
Software Shutdown
A1
A0
C1
C0
D7
D6
D5
D4
D3
D2
D1
D0
1
1
0
0
x
x
x
x
x
x
x
x
(LDAC = X, PDE = H)
This command shuts down all output buffer amplifiers,
reducing supply current to 10µA max.
0
1
1
1
0
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
UPO
Output
Low
High
(LDAC = X)
This command initiates the user-programmable logic
output for controlling another device across an isolated
interface. Example devices are gain control of an amplifier and a polarity output for a motor speed control.
No Operation (NOP)
A1
A0
C1
C0
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
x
x
x
x
x
x
x
x
(LDAC = X)
The NOP command (no operation) allows data to be
shifted through the MAX534 shift register without affecting the input or DAC registers. This is useful in daisy
chaining (also see the Daisy Chaining Devices section).
_______________________________________________________________________________________
9
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
For this command, the data bits are “Don't Cares.” As
an example, three MAX534s are daisy chained (A, B,
and C), and devices A and C need to be updated. The
36-bit-wide command would consist of one 12-bit word
for device C, followed by an NOP instruction for device
B and a third 12-bit word with data for device A. At CS’s
rising edge, device B will not change state.
Set DOUT Phase—SCLK Rising (Mode 1)
A1
A0
C1
C0
D7
D6
D5
D4
D3
D2
D1
D0
1
1
1
0
x
x
x
x
x
x
x
x
Serial Data Output
DOUT is the internal shift register’s output. DOUT can
be programmed to clock out data on SCLK’s falling
edge (mode 0) or rising edge (mode 1). In mode 0, output data lags input data by 12.5 clock cycles, maintaining compatibility with Microwire and SPI. In mode 1,
output data lags input data by 12 clock cycles. On
power-up, DOUT defaults to mode 0 timing. DOUT
never three-states; it always actively drives either high
or low and remains unchanged when CS is high.
(LDAC = x)
The mode 1 command resets the serial-output DOUT to
transition at SCLK’s rising edge. Once this command is
issued, DOUT’s phase is latched and will not change
except on power-up or if the specific command to set
the phase to falling edge is issued.
This command also loads all DAC registers with the contents of their respective input registers, and is identical to
the “LDAC” command.
SCLK
SK
MAX534 DIN
SO
MICROWIRE
PORT
CS
I/0
Set DOUT Phase—SCLK Falling (Mode 0, Default)
A1
A0
C1
C0
D7
D6
D5
D4
D3
D2
D1
D0
1
0
1
0
x
x
x
x
x
x
x
x
(LDAC = x)
This command resets DOUT to transition at SCLK’s
falling edge. The same command also updates all DAC
registers with the contents of their respective input registers, identical to the “LDAC” command.
LDAC Operation (Hardware)
LDAC is typically used in 4-wire interfaces (Figure 7).
This command is level sensitive, and allows asynchronous hardware control of the DAC outputs. With LDAC
low the DAC registers are transparent, and any time an
input register is updated, the DAC output immediately
follows.
Clear DACs with CLR
Strobing the CLR pin low causes an asynchronous
clear of input and DAC registers and sets all DAC outputs to zero. Similar to the LDAC pin, CLR can be
invoked at any time, typically when the device is not
selected (CS = H). When the DAC data is all zeros, this
function is equivalent to the “Update all DACs from Shift
Registers” command.
10
Figure 4. Connections for Microwire
MAX534 DIN
SCLK
CS
MOSI
SCK
I/0
Figure 5. Connections for SPI/QSPI
______________________________________________________________________________________
SPI/QSPI
PORT
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
Daisy-Chaining Devices
Any number of MAX534s can be daisy-chained by connecting DOUT of one device to DIN of the following
device in the chain. The NOP instruction (Table 1)
allows data to be passed from DIN to DOUT without
changing the input or DAC registers of the passing
device. A 3-wire interface updates daisy-chained or
individual MAX534s simultaneously by bringing CS
high (Figure 6).
SCLK
DIN
DIN
CS
CS
SCLK
DIN
DIN
CS
CS
Reference Input
The voltage at REF sets the full-scale output voltage for
all four DACs. The 460kΩ typical input impedance at
REF is code independent. The output voltage for any
DAC can be represented by a digitally programmable
voltage source as follows:
VOUT = (NB x VREF) / 256
where NB is the numerical value of the DAC’s binary
input code.
SCLK
DOUT
DIN
MAX534
SCLK
DOUT
CS
DEVICE A
SCLK
DAC Operation
The MAX534 uses a matrix decoding architecture for
the DACs, which saves power in the overall system.
The external reference voltage is divided down by a
resistor string placed in a matrix fashion. Row and column decoders select the appropriate tab from the
resistor string to provide the needed analog voltages.
The resistor string presents a code-independent input
impedance to the reference and guarantees a monotonic output. Figure 8 shows a simplified diagram of the
four DACs.
MAX534
MAX534
SCLK
Analog Section
DIN
DOUT
CS
DEVICE B
DEVICE C
TO OTHER
SERIAL DEVICES
MAX534
Figure 6. Daisy-chained or individual MAX534s are simultaneously updated by bringing CS high. Only three wires are required.
______________________________________________________________________________________
11
MAX534
Interfacing to the Microprocessor
The MAX534 is Microwire™ and SPI™/QSPI™ compatible (Figures 4 and 5). For SPI and QSPI, clear the
CPOL and CPHA configuration bits (CPOL = CPHA =
0). The SPI/QSPI CPOL = CPHA = 1 configuration can
also be used if the DOUT output is ignored.
The MAX534 can interface with Intel’s 80C5X/80C3X
family in mode 0 if the SCLK clock polarity is inverted.
More universally, if a serial port is not available, three
lines from one of the parallel ports can be used for bit
manipulation.
Digital feedthrough at the voltage outputs is greatly
minimized by operating the serial clock only to update
the registers. The clock idle state is low.
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
DIN
SCLK
LDAC
CS1
TO OTHER
SERIAL
DEVICES
CS2
CS3
CS
CS
CS
LDAC MAX534
LDAC MAX534
LDAC MAX534
SCLK
SCLK
SCLK
DIN
DIN
DIN
Figure 7. Multiple MAX534s sharing one DIN line. Simultaneously update by strobing LDAC, or specifically update by enabling an
individual CS.
REF
R0
R1
R15
D7
D5
MSB DECODER
R16
D6
D4
Output Buffer Amplifiers
All MAX534 voltage outputs are internally buffered by
precision unity-gain followers that slew at about
0.6V/µs. The outputs can swing from GND to VDD. With
a 0V to +4V (or +4V to 0V) output transition, the amplifier outputs will typically settle to 1/2LSB in 8µs when
loaded with 10kΩ in parallel with 100pF.
The buffer amplifiers are stable with any combination of
resistive (≥10kΩ) or capacitive loads.
R255
LSB DECODER
D3
D2
D1
D0
DAC A
Figure 8. DAC Simplified Circuit Diagram
12
______________________________________________________________________________________
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
DAC Linearity and Voltage Offset
The output buffer can have a negative input offset voltage that would normally drive the output negative, but
since there is no negative supply the output stays at 0V
(Figure 9). When linearity is determined using the endpoint method, it is measured between zero code (all
inputs 0) and full-scale code (all inputs 1) after offset
and gain error are calibrated out. However, in singlesupply operation the next code after zero may not
change the output, so the lowest code that produces a
positive output is the lower endpoint.
Power Sequencing
The voltage applied to REF should not exceed VDD at
any time. If proper power sequencing is not possible,
connect an external Schottky diode between REF and
VDD to ensure compliance with the absolute maximum
ratings. Do not apply signals to the digital inputs before
the device is fully powered up.
Careful PC board layout minimizes crosstalk among
DAC outputs and digital inputs. Figure 10 shows suggested circuit board layout to minimize crosstalk.
Unipolar-Output,
Two-Quadrant Multiplication
In unipolar operation, the output voltages and the reference input are the same polarity. Figure 11 shows the
MAX534 unipolar configuration, and Table 2 shows the
unipolar code.
SYSTEM GND
OUTC
OUTB
OUTD
OUTA
AGND
REF
Power-Supply Bypassing
and Ground Management
Connect AGND and DGND together at the IC. This
ground should then return to the highest-quality ground
available. Bypass VDD with a 0.1µF capacitor, located
as close to VDD and DGND as possible.
Figure 10. Suggested PC Board Layout for Minimizing
Crosstalk (Bottom View)
REFERENCE INPUT
3
REFAB
+3V
13
VDD
MAX534
2
DAC A
OUTPUT
VOLTAGE
OUTA
1
OUTB
DAC B
SERIAL
INTERFACE
NOT SHOWN
16
0V
NEGATIVE
OFFSET
DAC CODE
DAC C
OUTC
15
DAC D
OUTD
AGND
14
Figure 9. Effect of Negative Offset (Single Supply)
DGND
12
Figure 11. Unipolar Output Circuit
______________________________________________________________________________________
13
MAX534
__________Applications Information
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
Table 2. Unipolar Code Table
DAC CONTENTS
ANALOG
OUTPUT
MSB
LSB
1111
1111
255
+VREF ––––
256
1000
0001
129
+VREF ––––
256
1000
0000
0111
1111
127
+VREF ––––
256
0000
0001
1
+VREF ––––
256
0000
0000
0V
(
)
(
)
REF
128 = +V––––
+VREF ––––
256
2
(
)
(
)
(
)
1 )
Note: 1LSB = (VREF) (2-8) = +VREF (––––
256
_________________________________________________________Functional Diagram
DOUT CLR
LDAC
UPO
PDE
DECODE
CONTROL
VDD
REF
DGND
AGND
MAX534
OUTA
INPUT
REGISTER A
DAC
REGISTER A
DAC A
INPUT
REGISTER B
DAC
REGISTER B
DAC B
INPUT
REGISTER C
DAC
REGISTER C
DAC C
INPUT
REGISTER D
DAC
REGISTER D
DAC D
OUTB
12-BIT
SHIFT
REGISTER
OUTC
OUTD
SR
CONTROL
CS
14
DIN
SCLK
______________________________________________________________________________________
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
TRANSISTOR COUNT: 6821
________________________________________________________Package Information
DIM
A
A1
A2
B
C
D
E
e
H
h
L
N
S
α
D
A
e
A1
B
S
E
INCHES
MILLIMETERS
MAX
MIN
MIN
MAX
0.068
0.061
1.55
1.73
0.004 0.0098 0.127
0.25
0.061
0.055
1.40
1.55
0.012
0.008
0.20
0.31
0.0075 0.0098
0.19
0.25
SEE VARIATIONS
0.157
0.150
3.81
3.99
0.25 BSC
0.635 BSC
0.244
0.230
5.84
6.20
0.016
0.010
0.25
0.41
0.035
0.016
0.41
0.89
SEE VARIATIONS
SEE VARIATIONS
8°
0°
0°
8°
H
h x 45°
α
A2
N
E
C
DIM PINS
D
S
D
S
D
S
D
S
16
16
20
20
24
24
28
28
INCHES
MILLIMETERS
MIN
MAX MIN
MAX
0.189 0.196 4.80
4.98
0.0020 0.0070 0.05
0.18
0.337 0.344 8.56
8.74
0.0500 0.0550 1.27
1.40
0.337 0.344 8.56
8.74
0.0250 0.0300 0.64
0.76
0.386 0.393 9.80
9.98
0.0250 0.0300 0.64
0.76
21-0055A
QSOP
QUARTER
SMALL-OUTLINE
PACKAGE
L
______________________________________________________________________________________
15
MAX534
___________________Chip Information
MAX534
+5V, Low-Power, 8-Bit Quad DAC
with Rail-to-Rail Output Buffers
________________________________________________________Package Information
DIM
E1
D
A
A
B
B1
C
E
E1
e
L
L1
Q
S
S1
E
0°-15°
Q
L
L1
e
C
B1
B
S1
S
CERDIP
CERAMIC DUAL-IN-LINE
PACKAGE
(0.300 in.)
INCHES
MIN
MAX
–
0.200
0.014
0.023
0.038
0.065
0.008
0.015
0.220
0.310
0.290
0.320
0.100
0.125
0.200
0.150
–
0.015
0.070
–
0.098
0.005
–
DIM PINS
D
D
D
D
D
D
8
14
16
18
20
24
MILLIMETERS
MIN
MAX
–
5.08
0.36
0.58
0.97
1.65
0.20
0.38
5.59
7.87
7.37
8.13
2.54
3.18
5.08
3.81
–
0.38
1.78
–
2.49
0.13
–
INCHES
MILLIMETERS
MIN
MAX MIN MAX
–
0.405
–
10.29
–
0.785
–
19.94
–
0.840
–
21.34
–
0.960
–
24.38
–
1.060
–
26.92
–
1.280
–
32.51
21-0045A
D
E
DIM
E1
A
A1
A2
A3
B
B1
C
D1
E
E1
e
eA
eB
L
A3
A A2
L A1
0° - 15°
C
e
B1
B
eA
eB
D1
Plastic DIP
PLASTIC
DUAL-IN-LINE
PACKAGE
(0.300 in.)
INCHES
MAX
MIN
0.200
–
–
0.015
0.175
0.125
0.080
0.055
0.022
0.016
0.065
0.045
0.012
0.008
0.080
0.005
0.325
0.300
0.310
0.240
–
0.100
–
0.300
0.400
–
0.150
0.115
PKG. DIM PINS
P
P
P
P
P
N
D
D
D
D
D
D
8
14
16
18
20
24
INCHES
MIN
MAX
0.348 0.390
0.735 0.765
0.745 0.765
0.885 0.915
1.015 1.045
1.14 1.265
MILLIMETERS
MIN
MAX
–
5.08
0.38
–
3.18
4.45
1.40
2.03
0.41
0.56
1.14
1.65
0.20
0.30
0.13
2.03
7.62
8.26
6.10
7.87
2.54
–
7.62
–
–
10.16
2.92
3.81
MILLIMETERS
MIN
MAX
8.84
9.91
18.67 19.43
18.92 19.43
22.48 23.24
25.78 26.54
28.96 32.13
21-0043A
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
工商网监
湘ICP备2023018690号
