19-3477; Rev 3; 5/09
7-Channel Precision Temperature Monitor
The MAX6697 precision multichannel temperature sensor monitors its own temperature and the temperatures
of up to six external diode-connected transistors. All
temperature channels have programmable alert thresholds. Channels 1, 4, 5, and 6 also have programmable
overtemperature thresholds. When the measured temperature of a channel exceeds the respective threshold, a status bit is set in one of the status registers. Two
open-drain outputs, OVERT and ALERT, assert corresponding to these bits in the status register.
The 2-wire serial interface supports the standard system
management bus (SMBus™) protocols: write byte, read
byte, send byte, and receive byte for reading the temperature data and programming the alarm thresholds.
The MAX6697 is specified for an operating temperature
range of -40°C to +125°C and is available in 20-pin
QSOP and 20-pin TSSOP packages.
Applications
Desktop Computers
Notebook Computers
Features
♦ Six Thermal-Diode Inputs
♦ Local Temperature Sensor
♦ 1°C Remote Temperature Accuracy (+60°C to
+100°C)
♦ Temperature Monitoring Begins at POR for FailSafe System Protection
♦ ALERT and OVERT Outputs for Interrupts,
Throttling, and Shutdown
♦ Small 20-Pin QSOP and 20-Pin TSSOP Packages
♦ 2-Wire SMBus Interface
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX6697EP_ _
-40°C to +125°C
20 QSOP
MAX6697UP_ _
-40°C to +125°C
20 TSSOP
*See the Slave Address section.
Workstations
Servers
Pin Configuration appears at end of data sheet.
SMBus is a trademark of Intel Corp.
Typical Application Circuit
CPU
+3.3V
DXP
GND 20
4.7kΩ
EACH
SMBCLK 19
CLK
DXP2
SMBDATA 18
DATA
4
DXN2
ALERT 17
5
DXP3
VCC 16
6
DXN3
OVERT 15
7
DXP4
NC1 14
8
DXN4
NC2 13
1
DXP1
2
DXN1
3
2200pF
MAX6697
DXN
2200pF
INTERRUPT
TO μP
0.1μF
2200pF
TO SYSTEM
SHUTDOWN
2200pF
GPU
DXP
9
DXP5
DXP6 12
10
DXN5
DXN6 11
2200pF
2200pF
DXN
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX6697
General Description
MAX6697
7-Channel Precision Temperature Monitor
ABSOLUTE MAXIMUM RATINGS
VCC, SCK, SDA, ALERT, OVERT to GND ................-0.3V to +6V
DXP_ to GND..............................................-0.3V to (VCC + 0.3V)
DXN_ to GND ........................................................-0.3V to +0.8V
SDA, ALERT, OVERT Current .............................-1mA to +50mA
DXN Current .......................................................................±1mA
Continuous Power Dissipation (TA = +70°C)
20-Pin QSOP
(derate 9.1mW/°C above +70°C) ......................727.3mW(E20-1)
20-Pin TSSOP
(derate 11.0mW/°C above +70°C)..................879.1mW(U20-2)
ESD Protection (all pins, Human Body Model) ................±2000V
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +3.0V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VCC = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Supply Voltage
VCC
Standby Supply Current
ISS
SMBus static
30
Operating Current
ICC
During conversion
500
Channel 1 only
11
Other diode channels
8
Temperature Resolution
Remote Temperature Accuracy
3.0
VCC = 3.3V
Local Temperature Accuracy
VCC = 3.3V
1000
tCONV1
Remote Channels 2 Through 6
Conversion Time
tCONV_
Remote-Diode Source Current
IRJ
UVLO
-1.0
+1.0
-3.0
+3.0
TA = +60°C to +100°C
-2.0
+2.0
TA = 0°C to +125°C
-3.0
+3.0
C
o
o
Resistance cancellation on
95
125
156
Resistance cancellation off
190
250
312
95
125
156
High level
80
100
120
Low level
8
10
12
Falling edge of VCC disables ADC
2.30
2.80
2.95
VCC falling edge
1.2
2.0
90
POR Threshold Hysteresis
o
±2.5
Undervoltage-Lockout Hysteresis
Power-On Reset (POR) Threshold
µA
Bits
TA = TRJ = 0°C to +125°C
DXN_ grounded,
TRJ = TA = 0°C to +85°C
V
µA
±0.2
Remote Channel 1 Conversion
Time
UNITS
5.5
TA = TRJ = +60°C to +100°C
Supply Sensitivity of Temperature
Accuracy
Undervoltage-Lockout Threshold
MAX
C
C/V
ms
ms
µA
V
mV
2.5
90
V
mV
ALERT, OVERT
Output Low Voltage
VOL
ISINK = 1mA
0.3
ISINK = 6mA
0.5
Output Leakage Current
2
_______________________________________________________________________________________
1
V
µA
7-Channel Precision Temperature Monitor
(VCC = +3.0V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VCC = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SMBus INTERFACE (SCL, SDA)
Logic-Input Low Voltage
Logic-Input High Voltage
VIL
VIH
0.8
VCC = 3.0V
2.2
VCC = 5.0V
2.4
Input Leakage Current
V
-1
Output Low Voltage
VOL
Input Capacitance
CIN
V
V
ISINK = 6mA
+1
µA
0.3
V
5
pF
SMBus-COMPATIBLE TIMING (Figures 3 and 4) (Note 2)
Serial Clock Frequency
fSCL
Bus Free Time Between STOP
and START Condition
tBUF
START Condition Setup Time
Repeat START Condition Setup
Time
START Condition Hold Time
STOP Condition Setup Time
tSU:STA
tHD:STA
tSU:STO
Clock Low Period
tLOW
Clock High Period
tHIGH
Data Hold Time
tHD:DAT
Data Setup Time
tSU:DAT
Receive SCL/DSA Rise Time
Receive SCL/SDA Fall Time
Pulse Width of Spike Suppressed
SMBus Timeout
Note 1:
Note 2:
Note 3:
Note 4:
tR
(Note 3)
400
fSCL = 100kHz
4.7
fSCL = 400kHz
1.6
fSCL = 100kHz
4.7
fSCL = 400kHz
0.6
90% of SCL to 90% of SDA,
fSCL = 100kHz
0.6
90% of SCL to 90% of SDA,
fSCL = 400kHz
0.6
10% of SDA to 90% of SCL
0.6
90% of SCL to 90% of SDA,
fSCL = 100kHz
4
90% of SCL to 90% of SDA,
fSCL = 400kHz
0.6
10% to 10%, fSCL = 100kHz
1.3
10% to 10%, fSCL = 400kHz
1.3
µs
µs
µs
µs
µs
90% to 90%
0.6
fSCL = 100kHz
300
µs
µs
fSCL = 400kHz (Note 4)
900
fSCL = 100kHz
250
fSCL = 400kHz
100
1
fSCL = 400kHz
0.3
tF
tTIMEOUT
0
SDA low period for interface reset
25
ns
ns
fSCL = 100kHz
tSP
kHz
37
µs
300
ns
50
ns
45
ms
All parameters are tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Timing specifications are guaranteed by design.
The serial interface resets when SCL is low for more than tTIMEOUT.
A transition must internally provide at least a hold time to bridge the undefined region (300ns max) of SCL’s falling edge.
_______________________________________________________________________________________
3
MAX6697
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
STANDBY SUPPLY CURRENT
vs. SUPPLY VOLTAGE
REMOTE TEMPERATURE ERROR
vs. REMOTE-DIODE TEMPERATURE
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
7
6
5
4
3
2
1
0
2
TEMPERATURE ERROR (°C)
SUPPLY CURRENT (μA)
355
8
3
350
345
340
335
330
4.8
3.3
5.3
3.8
SUPPLY VOLTAGE (V)
4.3
4.8
5.3
2
1
0
-1
-2
5
75
3
2
1
0
-1
-2
-3
-4
-4
-5
50
75
100
0.1
125
1
FREQUENCY (MHz)
LOCAL TEMPERATURE ERROR
vs. POWER-SUPPLY NOISE FREQUENCY
REMOTE TEMPERATURE ERROR
vs. COMMON-MODE NOISE FREQUENCY
5
MAX6697 toc06
100mVP-P
TEMPERATURE ERROR (°C)
3
4
2
1
0
-1
-2
2
1
0
-1
-2
-3
-4
-4
0.01
0.1
FREQUENCY (MHz)
1
100mVP-P
3
-3
-5
0.001
MAX6697 toc07
25
DIE TEMPERATURE (°C)
TEMPERATURE ERROR (°C)
50
100mVP-P
4
-3
0
4
25
100
REMOTE-DIODE TEMPERATURE (°C)
TEMPERATURE ERROR (°C)
MAX6697 toc04
3
TEMPERATURE ERROR (°C)
0
REMOTE-DIODE TEMPERATURE ERROR
vs. POWER-SUPPLY NOISE FREQUENCY
4
4
-2
SUPPLY VOLTAGE (V)
LOCAL TEMPERATURE ERROR
vs. DIE TEMPERATURE
5
-1
MAX6697 toc05
4.3
0
-4
320
3.8
1
-3
325
3.3
MAX6697 toc03
360
MAX6697 toc02
12
11
10
9
MAX6697 toc01
STANDBY SUPPLY CURRENT (μA)
MAX6697
7-Channel Precision Temperature Monitor
-5
0.001
0.01
0.1
1
FREQUENCY (MHz)
_______________________________________________________________________________________
10
125
7-Channel Precision Temperature Monitor
REMOTE TEMPERATURE ERROR
vs. COMMON-MODE NOISE FREQUENCY
0
3
2
1
0
-1
-2
-3
MAX6697 toc09
100mVP-P
-0.5
TEMPERATURE ERROR (°C)
TEMPERATURE ERROR (°C)
4
MAX6697 toc08
5
TEMPERATURE ERROR
vs. DXP-DXN CAPACITANCE
-1.0
-1.5
-2.0
-2.5
-3.0
-3.5
-4.0
-4
-4.5
-5
0.001
-5.0
0.01
0.1
1
10
1
FREQUENCY (MHz)
100
10
DXP-DXN CAPACITANCE (nF)
Pin Description
PIN
NAME
FUNCTION
1
DXP1
Combined Current Source and A/D Positive Input for Channel 1 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave floating or connect to VCC if no
remote diode is used. Place a 2200pF capacitor between DXP1 and DXN1 for noise filtering.
2
DXN1
Cathode Input for Channel 1 Remote Diode. Connect the cathode of the channel 1 remote-diodeconnected transistor to DXN1.
3
DXP2
Combined Current Source and A/D Positive Input for Channel 2 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave floating or connect to VCC if no
remote diode is used. Place a 2200pF capacitor between DXP2 and DXN2 for noise filtering.
4
DXN2
Cathode Input for Channel 2 Remote Diode. Connect the cathode of the channel 2 remote-diodeconnected transistor to DXN2.
5
DXP3
Combined Current Source and A/D Positive Input for Channel 3 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave floating or connect to VCC if no
remote diode is used. Place a 2200pF capacitor between DXP3 and DXN3 for noise filtering.
6
DXN3
Cathode Input for Channel 3 Remote Diode. Connect the cathode of the channel 1 remote-diodeconnected transistor to DXN3.
7
DXP4
Combined Current Source and A/D Positive Input for Channel 4 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave floating or connect to VCC if no
remote diode is used. Place a 2200pF capacitor between DXP4 and DXN4 for noise filtering.
8
DXN4
Cathode Input for Channel 4 Remote Diode. Connect the cathode of the channel 1 remote-diodeconnected transistor to DXN4.
_______________________________________________________________________________________
5
MAX6697
Typical Operating Characteristics (continued)
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
7-Channel Precision Temperature Monitor
MAX6697
Pin Description (continued)
PIN
NAME
FUNCTION
9
DXP5
Combined Current Source and A/D Positive Input for Channel 5 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave floating or connect to VCC if no
remote diode is used. Place a 2200pF capacitor between DXP5 and DXN5 for noise filtering.
10
DXN5
Cathode Input for Channel 5 Remote Diode. Connect the cathode of the channel 1 remote-diodeconnected transistor to DXN5.
11
DXN6
Cathode Input for Channel 6 Remote Diode. Connect the cathode of the channel 1 remote-diodeconnected transistor to DXN6.
12
DXP6
Combined Current Source and A/D Positive Input for Channel 6 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave floating or connect to VCC if no
remote diode is used. Place a 2200pF capacitor between DXP6 and DXN6 for noise filtering.
13, 14
NC_
No Connect. Must be connected to ground.
15
OVERT
16
VCC
17
ALERT
18
SMBDATA
19
SMBCLK
20
GND
Overtemperature Active-Low, Open-Drain Output. OVERT asserts low when the temperature of
channels 1, 4, 5, and 6 exceeds the programmed threshold limit.
Supply Voltage Input. Bypass to GND with a 0.1µF capacitor.
SMBus Alert (Interrupt), Active-Low, Open-Drain Output. ALERT asserts low when the temperature of
any channel exceeds the programmed ALERT threshold.
SMBus Serial-Data Input/Output. Connect to a pullup resistor.
SMBus Serial-Clock Input. Connect to a pullup resistor.
Ground
Detailed Description
The MAX6697 is a precision multichannel temperature
monitor that features one local and six remote temperature-sensing channels with a programmable alert
threshold for each temperature channel and a programmable overtemperature threshold for channels 1, 4, 5,
and 6 (see Figure 1). Communication with the MAX6697
is achieved through the SMBus serial interface and a
dedicated alert pin. The alarm outputs, OVERT and
ALERT, assert if the software-programmed temperature
thresholds are exceeded. ALERT typically serves as an
interrupt, while OVERT can be connected to a fan, system shutdown, or other thermal-management circuitry.
ADC Conversion Sequence
In the default conversion mode, the MAX6697 starts the
conversion sequence by measuring the temperature on
channel 1, followed by 2, 3, local channel, 4, 5, and 6.
The conversion result for each active channel is stored
in the corresponding temperature data register.
In some systems, one of the remote thermal diodes may
be monitoring a location that experiences temperature
changes that occur much more rapidly than in the other
6
channels. If faster temperature changes must be monitored in one of the temperature channels, the MAX6697
allows channel 1 to be monitored at a faster rate than
the other channels. In this mode (set by writing a 1 to bit
4 of the configuration 1 register), measurements of
channel 1 alternate with measurements of the other
channels. The sequence becomes channel 1, channel
2, channel 1, channel 3, channel 1, etc. Note that the
time required to measure all seven channels is considerably greater in this mode than in the default mode.
Low-Power Standby Mode
Standby mode reduces the supply current to less than
15µA by disabling the internal ADC. Enter standby by
setting the STOP bit to 1 in the configuration 1 register.
During standby, data is retained in memory, and the
SMBus interface is active and listening for SMBus commands. The timeout is enabled if a start condition is recognized on SMBus. Activity on the SMBus causes the
supply current to increase. If a standby command is
received while a conversion is in progress, the conversion cycle is interrupted, and the temperature registers
are not updated. The previous data is not changed and
remains available.
_______________________________________________________________________________________
7-Channel Precision Temperature Monitor
MAX6697
VCC
DXP1
MAX6697
ADC
DXN1
DXP2
10/100μA
ALARM
ALU
DXN2
OVERT
AVERT
DXP3
DXN3
COUNT
INPUT
BUFFER
DXP4
REGISTER BANK
COMMAND BYTE
COUNTER
REMOTE TEMPERATURES
DXN4
LOCAL TEMPERATURES
REF
DXP5
ALERT THRESHOLD
OVERT THRESHOLD
DXN5
ALERT RESPONSE ADDRESS
DXP6
SMBus
INTERFACE
DXN6
SCL
SDA
Figure 1. Internal Block Diagram
SMBus Digital Interface
From a software perspective, the MAX6697 appears as
a series of 8-bit registers that contain temperature measurement data, alarm threshold values, and control bits.
A standard SMBus-compatible 2-wire serial interface is
used to read temperature data and write control bits
and alarm threshold data. The same SMBus slave
address also provides access to all functions.
The MAX6697 employs four standard SMBus protocols:
write byte, read byte, send byte, and receive byte
(Figure 2). The shorter receive byte protocol allows
quicker transfers, provided that the correct data register was previously selected by a read byte instruction.
Use caution with the shorter protocols in multimaster
systems, since a second master could overwrite the
command byte without informing the first master. Figure
3 is the SMBus write timing diagram and Figure 4 is the
SMBus read timing diagram.
The remote diode 1 measurement channel provides 11
bits of data (1 LSB = 0.125°C). All other temperaturemeasurement channels provide 8 bits of temperature
data (1 LSB = 1°C). The 8 most significant bits (MSBs)
can be read from the local temperature and remote
temperature registers. The remaining 3 bits for remote
diode 1 can be read from the extended temperature
register. If extended resolution is desired, the extended
resolution register should be read first. This prevents
the most significant bits from being overwritten by new
_______________________________________________________________________________________
7
MAX6697
7-Channel Precision Temperature Monitor
Write Byte Format
S
ADDRESS
WR
ACK
COMMAND
7 bits
ADDRESS
WR
ACK
7 bits
COMMAND
ACK
Command Byte: selects
which register you are
reading from
S
1
ADDRESS
RD
ACK
DATA
///
P
8 bits
Slave Address: repeated
due to change in dataflow direction
Data Byte: reads from
the register set by the
command byte
Receive Byte Format
WR
7 bits
ACK
COMMAND
ACK
P
8 bits
S
ADDRESS
7 bits
RD
ACK
DATA
///
P
8 bits
Data Byte: reads data from
the register commanded
by the last read byte or
write byte transmission;
also used for SMBus alert
response return address
Command Byte: sends command with no data, usually
used for one-shot command
S = Start condition
P = Stop condition
P
Data Byte: data goes into the register
set by the command byte (to set
thresholds, configuration masks, and
sampling rate)
7 bits
Send Byte Format
ADDRESS
ACK
8 bits
Command Byte: selects which
register you are writing to
8 bits
Slave Address: equivalent to chip-select line
S
DATA
8 bits
Slave Address: equivalent to chip-select line of
a 3-wire interface
S
ACK
Shaded = Slave transmission
/// = Not acknowledged
Figure 2. SMBus Protocols
Table 1. Main Temperature Register
(High Byte) Data Format
TEMP (°C)
DIGITAL OUTPUT
TEMP (°C)
DIGITAL OUTPUT
>127
0111 1111
0
000X XXXX
127
0111 1111
+0.125
001X XXXX
126
0111 1110
+0.250
010X XXXX
25
0001 1001
+0.375
011X XXXX
0.00
0000 0000
+0.500
100X XXXX
工商网监
湘ICP备2023018690号
