MAX690–MAX695
Microprocessor Supervisory Circuits
General Description
The MAX690 family of supervisory circuits reduces the
complexity and number of components required for
power supply monitoring and battery control functions in
microprocessor systems. These include µP reset and
backup-battery switchover, watchdog timer, CMOS RAM
write protection, and power-failure warning. The MAX690
family significantly improves system reliability and accuracy compared to that obtainable with separate ICs or
discrete components.
The MAX690, MAX692, and MAX694 are supplied in
8-pin packages and provide four functions:
●● A reset output during power-up, power-down, and
brownout conditions.
●● Battery backup switching for CMOS RAM, CMOS
microprocessor or other low power logic.
●● A Reset pulse if the optional watchdog timer has not
been toggled within a specified time.
●● A 1.3V threshold detector for power fail warning, low
battery detection, or to monitor a power supply other
than +5V.
Benefits and Features
●● Supervisory Function Integration Saves Board Space
while Fully Protecting Microprocessor-Based Systems
• Precision Voltage Monitor
-- 4.65V (MAX690, MAX691, MAX694, MAX695)
-- 4.40V (MAX692, MAX693)
• Power OK/Reset Time Delay
-- 50ms, 200ms, or Adjustable
• Watchdog Timer
-- 100ms, 1.6s, or Adjustable
• Battery Backup Power Switching
• Voltage Monitor for Power Fail or Low Battery
Warning
• Minimum External Component Count
●● Low Power Consumption in Battery Backup Mode
Extends Battery Life
• 1µA Standby Current
●● Onboard Gating of Chip Enable Signals Protects
Against Erroneous Data Written to RAM During Low
VCC Events
Applications
●● Write protection of CMOS RAM or EEPROM.
●●
●●
●●
●●
●●
●● Adjustable reset and watchdog timeout periods.
Ordering information appears at end of data sheet.
The MAX691, MAX693, and MAX695 are supplied in 16-pin
packages and perform all MAX690, MAX692, MAX694
functions, plus:
●● Separate outputs for indicating a watchdog timeout,
backup-battery switchover, and low VCC.
Computers
Controllers
Intelligent Instruments
Automotive Systems
Critical µP Power Monitoring
Pin Configurations
TOP VIEW
Typical Operating Circuit
VOUT 1
VCC 2
GND 3
MAX690
MAX692
MAX694
PFI 4
+5V
VOUT
VCC
VBATT
POWER TO
CMOS RAM
RESET
PFI
GND
µP RESET
PFO
µP NMI
WDI
I/O
LINE
MAX690 TYPICAL APPLICATION
19-0218; Rev 5; 4/15
7 RESET
6 WDI
5 PFO
µP
POWER
µP
SYSTEM
MAX690
8 VBATT
VBATT 1
16 RESET
VOUT 2
VCC 3
GND 4
BATT ON 5
15 RESET
MAX691
MAX693
MAX695
14 WDO
13 CE IN
12 CE OUT
LOW LINE 6
11 WDI
OSC IN 7
10 PFO
OSC SEL 8
9 PFI
MAX690–MAX695
Microprocessor Supervisory Circuits
Absolute Maximum Ratings
Terminal Voltage (with respect to GND)
VCC....................................................................-0.3V to +6.0V
VBATT................................................................-0.3V to +6.0V
All Other Inputs (Note 1) .................... -0.3V to (VOUT + 0.5V)
Input Current
VCC................................................................................200mA
VBATT..............................................................................50mA
GND ................................................................................20mA
Output Current
VOUT......................................................Short circuit protected
All Other Outputs.............................................................20mA
Rate-of-Rise, VBATT, VCC...............................................100V/µs
Operating Temperature Range
C suffix.................................................................0°C to +70°C
E suffix............................................................. -40°C to +85°C
M suffix.......................................................... -55°C to +125°C
Power Dissipation
8-Pin Plastic DIP
(derate 5mW/°C above +70°C).....................................400mV
8-Pin CERDIP
(derate 8mW/°C above +85°C).....................................500mV
16-Pin Plastic DIP
(derate 7mW/°C above +70°C).....................................600mV
16-Pin Small Outline
(derate 7mW/°C above +70°C).....................................600mV
16-Pin CERDIP
(derate 10mW/°C above +85°C)...................................600mV
Storage Temperature Range............................. -65°C to +160°C
Lead Temperature (Soldering, 10s).................................... 300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
VCC = full operating range, VBATT = 2.8V, TA = +25°C, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
BATTERY BACKUP SWITCHING
Operating Voltage Range
(MAX690, MAX691, MAX694, MAX695 VCC)
4.75
5.5
Operating Voltage Range (MAX690, MAX691,
MAX694, MAX695 VBATT)
2.0
4.25
Operating Voltage Range
(MAX692, MAX693 VCC)
4.5
5.5
Operating Voltage Range
(MAX692, MAX693 VBATT)
2.0
4.0
VOUT Output Voltage
VOUT in Battery Backup Mode
V
IOUT = 1mA
VCC 0.3
VCC 0.1
IOUT = 50mA
VCC 0.5
VCC 0.25
IOUT = 250µA, VCC < VBATT - 0.2V
VBATT
- 0.1
VBATT
- 0.02
V
V
IOUT = 1mA
2
5
IOUT = 50mA
3.5
10
Supply Current in Battery Backup Mode
VCC = 0V, VBATT = 2.8V
0.6
1
Battery Standby Current
(+ = Discharge, - = Charge)
5.5V > VCC >
VBATT + 1V
Battery Switchover Threshold
(VCC - VBATT)
Power-up
70
Power-down
50
Supply Current (Excluded IOUT)
www.maximintegrated.com
TA = +25°C
-0.1
+0.02
TA = full operating
range
-1.0
+0.02
mA
µA
µA
mV
Maxim Integrated │ 2
MAX690–MAX695
Microprocessor Supervisory Circuits
Electrical Characteristics (continued)
VCC = full operating range, VBATT = 2.8V, TA = +25°C, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
Battery Switchover Hysteresis
BATT ON Output Voltage
BATT ON Output Short-Circuit Current
TYP
MAX
20
ISINK = 3.2mA
mV
0.4
BATT ON = VOUT = 4.5V sink current
BATT ON = 0V source current
UNITS
25
V
mA
0.5
1
25
MAX690, MAX691,
MAX694, MAX695
4.5
4.65
4.75
MAX692, MAX693
4.25
4.4
4.5
µA
RESET AND WATCHDOG TIMER
Reset Voltage Threshold
TA = full
operating range
Reset Threshold Hysteresis
40
V
mV
Reset Timeout Delay (MAX690/MAX691/
MAX692/MAX693)
Figure 6, OSC SEL HIGH, VCC = 5V
35
50
70
ms
Reset Timeout Delay (MAX694/MAX695)
Figure 6, OSC SEL HIGH, VCC = 5V
140
200
280
ms
Long period, VCC = 5V
1.0
1.6
2.25
s
Short period, VCC = 5V
70
100
140
ms
Clock
Cycles
Watchdog Timeout Period, Internal Oscillator
Watchdog Timeout Period, External Clock
Minimum WDI Input Pulse Width
RESET and LOW LINE Output Voltage
RESET and WDO Output Voltage
Long period
3840
4097
Short period
768
1025
VIL = 0.4, VIH = 0.8VCC
200
ISINK = 1.6mA, VCC = 4.25V
ISOURCE = 1µA, VCC = 5V
0.4
3.5
ISINK = 1.6mA
ISOURCE = 1µA, VCC = 5V
Output Short-Circuit Current
RESET, RESET, WDO, LOW LINE
WDI Input Threshold Logic-Low
VCC = 5V (Note 2)
WDI Input Threshold Logic-High
VCC = 5V (Note 2)
WDI Input Current
ns
0.4
3.5
1
3
25
0.8
3.5
WDI = VOUT
20
WDI = 0V
-50
VCC = 5V, TA = full
1.2
50
-15
V
V
µA
V
µA
POWER-FAIL DETECTOR
PFI Threshold
PFI Current
PFO Output Voltage
PFO Short Circuit Source Current
www.maximintegrated.com
1.3
1.4
V
±0.01
±25
nA
0.4
V
25
µA
ISINK = 3.2mA
ISOURCE = 1µA
PFI = VIH, PFO = 0V
3.5
1
V
3
Maxim Integrated │ 3
MAX690–MAX695
Microprocessor Supervisory Circuits
Electrical Characteristics (continued)
VCC = full operating range, VBATT = 2.8V, TA = +25°C, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
CHIP ENABLE GATING
VIL
CE IN Thresholds
0.8
VIH
V
3.0
CE IN Pullup Current
3
µA
ISINK = 3.2mA
CE OUT Output Voltage
CE Propagation Delay
0.4
ISOURCE = 3.0mA
VOUT - 1.5
ISOURCE = 1µA, VCC = 0V
VOUT - 0.05
VCC = 5V
V
50
200
ns
OSCILLATOR
OSC IN Input Current
±2
OSC SEL Input Pullup Current
µA
5
OSC IN Frequency Range
OSC SEL = 0V
OSC IN Frequency
with External Capacitor
OSC SEL = 0V
COSC = 47pF
0
µA
250
4
kHz
kHz
Note 1: The input voltage limits on PFI and WDI may be exceeded provided the input current is limited to less than 10mA.
Note 2: WDI is guaranteed to be in the mid-level (inactive) state if WDI is floating and VCC is in the operating voltage range. WDI is
internally biased to 38% of VCC with an impedance of approximately 125kΩ.
Pin Description
PIN
MAX690/
MAX692/
MAX694
MAX691/
MAX693/
MAX695
NAME
2
3
VCC
8
1
VBATT
Backup Battery Input. Connect to Ground if a backup battery is not used.
1
2
VOUT
The higher of VCC or VBATT is internally switched to VOUT. Connect VOUT to VCC if
VOUT and VBATT are not used. Connect a 0.1µF or larger bypass capacitor to VOUT.
3
4
GND
0V Ground Reference for All Signals
7
15
RESET
FUNCTION
The +5V Input
RESET goes low whenever VCC falls below either the reset voltage threshold or the
VBATT input voltage. The reset threshold is typically 4.65V for the MAX690/691/694/695,
and 4.4V for the MAX692 and MAX693. RESET remains low for 50ms after VCC returns
to 5V, (except 200ms in MAX694/695). RESET also goes low for 50ms if the Watchdog
Timer is enabled but not serviced within its timeout period. The RESET pulse width can
be adjusted as shown in Table 1.
6
11
WDI
Watchdog Input (WDI). WDI is a three level input. If WDI remains either high or low for
longer than the watchdog timeout period, RESET pulses low and WDO goes low. The
Watchdog Timer is disabled when WDI is left floating or is driven to mid-supply. The
timer resets with each transition at the Watchdog Timer input.
4
9
PFI
Noninverting Input to the Power-Fail Comparator. When PFI is less than 1.3V, PFO
goes low. Connect PFI to GND or VOUT when not used. See Figure 1.
www.maximintegrated.com
Maxim Integrated │ 4
MAX690–MAX695
Microprocessor Supervisory Circuits
Pin Description (continued)
PIN
MAX690/
MAX692/
MAX694
MAX691/
MAX693/
MAX695
NAME
5
10
PFO
—
13
CE IN
—
12
CE OUT
CE OUT goes low only when CE IN is low and VCC is above the reset threshold (4.65V
for MAX691 and MAX695, 4.4V for MAX693). See Figure 6.
FUNCTION
Output of the Power-Fail Comparator. It goes low when PFI is less than 1.3V. The
comparator is turned off and PFO goes low when VCC is below VBATT.
CE Gating Circuit Input. Connect to GND or VOUT if not used.
—
5
BATT ON
BATT ON goes high when VOUT is internally switched to the VBATT input. It goes low
when VOUT is internally switched to VCC. The output typically sinks 25mA and can
directly drive the base of an external PNP transistor to increase the output current
above the 50mA rating of VOUT.
—
6
LOW LINE
LOW LINE goes low when VCC falls below the reset threshold. It returns high as soon
as VCC rises above the reset threshold. See Figure 6, Reset Timing.
—
16
RESET
—
8
OSC SEL
—
—
7
14
www.maximintegrated.com
OSC IN
WDO
Active-High Output. It is the inverse of RESET.
When OSC SEL is unconnected or driven high, the internal oscillator sets the reset time
delay and watchdog timeout period. When OSC SEL is low, the external oscillator input,
OSC IN, is enabled. OSC SEL has a 3µA internal pullup. See Table 1.
When OSC SEL is low, OSC IN can be driven by an external clock to adjust both the
reset delay and the watchdog timeout period. The timing can also be adjusted by
connecting and external oscillator to this pin. See Figure 8. When OSC SEL is high or
floating, OSC IN selects between fast and slow Watchdog timeout periods.
The Watchdog Output (WDO). WDO goes low if WDI remains either high or low for
longer than the watchdog timeout period. WDO is set high by the next transition at WDI.
If WDI is unconnected or at mid-supply, WDO remains high. WDO also goes high when
LOW LINE goes low.
Maxim Integrated │ 5
MAX690–MAX695
Microprocessor Supervisory Circuits
Typical Applications
power-up RESET pulse lasts 50ms* to allow for this
oscillator start-up time. The manual reset switch and
the 0.1µF capacitor connected to the reset bus can be
omitted if manual reset is not needed. An inverted, active
high, RESET output is also supplied.
MAX691, MAX693, and MAX695
A typical connection for the MAX691/693/695 is shown
in Figure 1. CMOS RAM is powered from VOUT. VOUT is
internally connected to VCC when 5V power is present,
or to VBATT when VCC is less than the battery voltage.
VOUT can supply 50mA from VCC, but if more current
is required, an external PNP transistor can be added.
When VCC is higher than VBATT, the BATT ON output
goes low, providing 25mA of base drive for the external
transistor. When VCC is lower than VBATT, an internal
200Ω MOSFET connects the backup battery to VOUT.
The quiescent current in the battery backup mode is 1µA
maximum when VCC is between 0V and VBATT–700mV.
Power-Fail Detector
The MAX691/93/95 issues a nonmaskable interrupt (NMI)
to the microprocessor when a power failure occurs. The
+5V power line is monitored via two external resistors
connected to the power-fail input (PFI). When the voltage at PFI falls below 1.3V, the power-fail output (PFO)
drives the processor’s NMI input low. If a power-fail
threshold of 4.8V is chosen, the microprocessor will
have the time when VCC fails from 4.8V to 4.65V to save
data into RAM. An earlier power-fail warning can be
generated if the unregulated DC input of the 5V regulator
is available for monitoring.
Reset Output
A voltage detector monitors VCC and generates a RESET
output to hold the microprocessor’s Reset line low when
VCC is below 4.65V (4.4V for MAX693). An internal
monostable holds RESET low for 50ms* after VCC rises
above 4.65V (4.4V for MAX693). This prevents repeated
toggling of RESET even if the 5V power drops out and
recovers with each power line cycle.
RAM Write Protection
The MAX691/MAX693/MAX695 CE OUT line drives the
Chip Select inputs of the CMOS RAM. CE OUT follows
CE IN as long as VCC is above the 4.65V (4.4V for
MAX693) reset threshold. If VCC falls below the reset
threshold, CE OUT goes high, independent of the logic
level at CE IN. This prevents the microprocessor from
writing erroneous data into RAM during power-up, powerdown, brownouts, and momentary power interruptions.
The LOW LINE output goes low when VCC falls below
4.65V (4.4V for MAX693).
The crystal oscillator normally used to generate the clock
for microprocessors takes several milliseconds to start.
Since most microprocessors need several clock cycles
to reset, RESET must be held low until the microprocessor clock oscillator has started. The MAX690 family
*200ms for MAX695
+5V
VCC
INPUT
0.1µF
0.1µF
3
1
VCC
VBATT
5
BATT ON
3V
BATTERY
CE OUT
9
4
7
NO CONNECTION
VOUT
8
PFI
CE IN
MAX691
MAX693
MAX695
WDI
GND
PFO
OSC IN
RESET
OSC SEL
LOW LINE
6
WDO
14
SYSTEM STATUS INDICATORS
2
CMOS
RAM
12
13
ADDRESS
DECODE
A0-A15
11
I/O
10
NMI
15
RESET
RESET
0.1µF
MICROPROCESSOR
AUDIBLE
ALARM
OTHER SYSTEM RESET SOURCES
Figure 1. MAX691/693/695 Typical Application
www.maximintegrated.com
Maxim Integrated │ 6
MAX690–MAX695
Microprocessor Supervisory Circuits
Watchdog Timer
application. Operation is much the same as with the
MAX691/MAX693/MAX695 (Figure 1), but in this case, the
power- fail input (PFI) monitors the unregulated input to the
7805 regulator. The MAX690/MAX694 RESET output goes
low when VCC falls below 4.65V. The RESET output of the
MAX692 goes low when VCC drops below 4.4V.
The microprocessor drives the WATCHDOG INPUT
(WDI) with an I/O line. When OSC IN and OSC SEL are
unconnected, the microprocessor must toggle the WDI
pin once every 1.6s to verify proper software execution. If
a hardware or software failure occurs such that WDI not
toggled the MAX691/MAX693 will issue a 50ms* RESET
pulse after 1.6s. This typically restarts the microprocessor’s power-up routine. A new RESET pulse is issued
every 1.6s until the WDI is again strobed.
The current consumption of the battery-backed-up power
bus must be less than 50mA. The MAX690/MAX692/
MAX694 does not have a BATT ON output to drive an
external transistor. The MAX690/MAX692/MAX694 also
does not include chip enable gating circuitry that is available on the MAX690/MAX692/MAX694. In many systems
though, CE gating is not needed since a low input to
the microprocessor RESET line prevents the processor
from writing to RAM during power-up and power-down
transients.
The WATCHDOG OUTPUT (WDO) goes low if the
watchdog timer is not serviced within its timeout period.
Once WDO goes low it remains low until a transition
occurs at WDI. The watchdog timer feature can be disabled by leaving WDI unconnected. OSC IN and OSC
SEL also allow other watchdog timing options, as shown
in Table 1 and Figure 8.
The MAX690/MAX692/MAX694 watchdog timer has a
fixed 1.6s timeout period. If WDI remains either low or
high for more than 1.6s, a RESET pulse is sent to the
microprocessor. The watchdog timer is disabled if WDI is
left unconnected.
MAX690, MAX692, and MAX694
The 8 pin MAX690, MAX692, and MAX694 have most
of the features of the MAX691, MAX693, and MAX695.
Figure 2 shows the MAX690/MAX692/MAX694 in a typical
*200ms for MAX695
+8V
7805
3-TERMINAL
REGULATOR
+5V
2
0.1µF
4
VCC
VOUT
MAX690
MAX692
MAX694
VBATT
PFI
RESET
PFO
GND
WDI
1
8
7
5
6
0.1µF
POWER
TO
CMOS
RAM
MICROPROCESSOR
POWER
MICROPROCESSOR
RESET
NMI
I/O LINE
3
Figure 2. MAX690/692/694 Typical Application
www.maximintegrated.com
Maxim Integrated │ 7
MAX690–MAX695
Microprocessor Supervisory Circuits
Detailed Description
Battery-Switchover and VOUT
The battery switchover circuit compares VCC to the VBATT
input, and connects VOUT to whichever is higher. Switchover
occurs when VCC is 50mV greater than VBATT as VCC falls,
and VCC is 70mV more than VBATT as VCC rises (see
Figure 4). The switchover comparator has 20mV of hysteresis to prevent repeated, rapid switching if VCC falls very
slowly or remains nearly equal to the battery voltage.
When VCC is higher than VBATT, VCC is internally
switched to VOUT via a low saturation PNP transistor. VOUT has 50mA output current capability. Use an
external PNP pass transistor in parallel with internal transistor if the output current requirement at VOUT exceeds
50mA or if a lower VCC-VOUT voltage differential is
desired. The BATT ON output (MAX691/MAX693/MAX695
only) can directly drive the base of the external transistor.
It should be noted that the MAX690–MAX695 need only
supply the average current drawn by the CMOS RAM if
there is adequate filtering. Many RAM data sheets specify
a 75mA maximum supply current, but this peak current
spike lasts only 100ns. A 0.1µF bypass capacitor at VOUT
supplies the high instantaneous current, while VOUT need
only supply the average load current, which is much less.
A capacitance of 0.1µF or greater must be connected to
the VOUT terminal to ensure stability.
A 200Ω MOSFET connects VBATT input to VOUT during
battery backup. This MOSFET has very low input-tooutput differential (dropout voltage) at the low current
levels required for battery backup of CMOS RAM or other
low power CMOS circuitry. When VCC equals VBATT the
supply current is typically 12µA. When VCC is between
0V and (VBATT - 700mV) the typical supply current is only
600nA typical, 1µA maximum.
The MAX690/MAX691/MAX694/MAX695 operate with
battery voltages from 2.0V to 4.25V while MAX692/
MAX693 operate with battery voltages from 2.0V to
4.0V. High value capacitors can also be used for shortterm memory backup. External circuitry is required to
ensure that the capacitor voltage does not rise above
the reset threshold, and that the charging resistor does
not discharge the capacitor when in backup mode. The
MAX691A and the MAX791 provide solutions requiring
fewer external components.
A small charging current of typically 10nA (0.1µA max)
flows out of the VBATT terminal. This current varies with the
amount of current that is drawn from VOUT but its polarity
is such that the backup battery is always slightly charged,
and is never discharged while VCC is in its operating voltage range. This extends the shelf life of the backup battery
by compensating for its self-discharge current. Also note
that this current poses no problem when lithium batteries
are used for backup since the maximum charging current
(0.1µA) is safe for even the smallest lithium cells.
If the battery-switchover section is not used, connect
VBATT to GND and connect VOUT to VCC. Table 2 shows
the state of the inputs and output in the low power battery
backup mode.
VBATT
1
VCC
CHIP-ENABLE INPUT
3
5
BATT ON
+
2
-
12
13
6
+
*4.4V (MAX693)
*
4.65V
15
-
16
RESET GENERATOR
OSC IN
OSC SEL
WATCHDOG INPUT
POWER FAIL
INPUT
7
TIMEBASE FOR RESET
AND
WATCHDOG
8
11
WATCHDOG TRANSITION
DETECTOR
9
WATCHDOG
TIMER
+
1.3V
14
10
-
4
VOUT
CHIP ENABLE OUTPUT
LOW LINE
RESET
RESET
WATCHDOG OUTPUT
POWER FAIL OUTPUT
GROUND
Figure 3. MAX691/MAX693/MAX695 Block Diagram
www.maximintegrated.com
Maxim Integrated │ 8
MAX690–MAX695
Microprocessor Supervisory Circuits
VCC
+5V
VOUT
VCC
P CHANNEL
MOSFET
BASE DRIVE
100
mV
3V
BATTERY
INPUT
+
BATT ON
(MAX691, MAX693, MAX695 ONLY)
-
700
mV
0.1F
TO CMOS
RAM AND
REALTIME
CLOCK
VCC IN
+
+
LOW IQ MODE
-
SELECT
INTERNAL
SHUTDOWN
SIGNAL WHEN
VBATT > VCC + 0.7V
Figure 4. Battery-Switchover Block Diagram
Reset Output
RESET is an active-low output which goes low whenever VCC falls below 4.5V (MAX690/MAX691/MAX694/
MAX695) or 4.25V (MAX692/MAX693). It will remain low
until VCC rises above 4.75V (MAX690/691/694/695) or 4.5V
(MAX692/MAX693) for milliseconds*. See Figures 5 and 6.
The guaranteed minimum and maximum thresholds of
MAX690/MAX691/MAX694/MAX695 are 4.5V and 4.75V,
while the guaranteed thresholds of the MAX692/MAX693
are 4.25V and 4.5V. The MAX690/MAX691/MAX694/
MAX695 is compatible with 5V supplies with a +10%, -5%
tolerance while the MAX692/MAX693 is compatible with
5V ±10% supplies. The reset threshold comparator has
approximately 50mV of hysteresis, with a nominal threshold of 4.65V in the MAX690/MAX691/MAX694/MAX695,
and 4.4V in the MAX692/MAX693.
The response time of the reset voltage comparator is
about 100µs. VCC should be bypassed to ensure that
glitches do not activate the RESET output.
RESET also goes low if the watchdog timer is enabled
and WDI remains either high or low longer than the watchdog timeout period. RESET has an internal 3µA pullup,
and can either connect to and open collector Reset bus
or directly drive a CMOS gate without and external pullup
resistor.
CE Gating and RAM Write Protection
The MAX691/MAX693/MAX695 use two pins to control
the Chip Enable or Write inputs of CMOS RAMs. When
VCC is +5V, CE OUT is a buffered replica of CE IN, with
a 50ns propagation delay. If VCC input falls below 4.65V
(4.5V min, 4.75V max) an internal gate forces CE OUT
high, independent of CE IN. The MAX693 CE OUT goes
high whenever VCC is below 4.4V (4.25V min, 4.5V max).
The CE output of both devices is also forced high when
VCC is less than VBATT. (See Figure 5.)
CE OUT typically drives the CE, CS, or Write input of
battery backed up CMOS RAM. This ensures the integrity of the data in memory by preventing write operations
when VCC is at and invalid level. Similar protection of
EEPROMs can be achieved by using the CE OUT to
drive the Store or Write inputs of an EEPROM, EAROM,
or NOVRAM.
If the 50ns typical propagation delay of CE OUT is too
long, connect CE IN to GND and use the resulting CE
OUT to control a high speed external logic gate. A second
alternative is to AND the LOW LINE output with the CE or
WR signal. An external logic gate and the RESET output
of the MAX690/MAX692/MAX694 can also be used for
CMOS RAM write protection.
*200ms for MAX694 and MAX695
www.maximintegrated.com
Maxim Integrated │ 9
MAX690–MAX695
Microprocessor Supervisory Circuits
CE IN
CE OUT
LOW LINE
VCC
RESET
POWER-ON
RESET
METAL
LINK
TRIMMED
RESISTORS
+
RESET RESET
TIME
1.3V
RESET
QR
WATCHDOG
FROM
WATCHDOG
TIMER
10 kHz CLOCK
FROM TIMEBASE
SECTION
Figure 5. Reset Block Diagram
VCC
RESET
OUTPUT
4.7V
50ms*
4.6V
4.7V
4.6V
50ms*
LOW LINE
OUTPUT
CE IN
CE IN
VOUT - VBATT
*200ms FOR MAX694 AND MAX695
Figure 6. Reset Timing
www.maximintegrated.com
Maxim Integrated │ 10
MAX690–MAX695
Microprocessor Supervisory Circuits
1.3V Comparator and Power-Fail Warning
at the end of reset, whether the reset was caused by
lack of activity on WDI or by VCC falling below the reset
threshold. If WDI remains either high or low, reset pulses
will be issued every 1.6s. The watchdog monitor can be
deactivated by floating the watchdog input (WDI).
The power-fail input (PFI) is compared to an internal
1.3V reference. The power-fail output (PFO) goes low
when the voltage at PFI is less than 1.3V. Typically, PFI is
driven by an external voltage divider which senses either
the unregulated DC input to the system’s 5V regulator or
the regulated 5V output. The voltage divider ratio can be
chosen such that the voltage at PFI falls below 1.3V several milliseconds before the +5V supply falls below 4.75V.
PFO is normally used to interrupt the microprocessor so
that data can be stored in RAM before VCC falls below
4.75V and the RESET output goes low (4.5V for MAX692/
MAX693).
The watchdog output (WDO, MAX691/MAX693/MAX695
only) goes low if the watchdog timer times out and
remains low until set high by the next transition on the
watchdog input. WDO is also set high when VCC goes
below the reset threshold.
The watchdog timeout period is fixed at 1.6s and the
reset pulse width is fixed at 50ms* on the 8-pin MAX690/
MAX692/MAX694. The MAX691/MAX693/MAX695 allow
these times to be adjusted per Table 1. Figures 8 shows
various oscillator configurations.
The power-fail detector can also monitor the backup battery to warn of a low battery condition. To conserve battery power, the power-fail detector comparator is turned
off and PFO is forced when VCC is lower than VBATT
input voltage.
The internal oscillator is enabled when OSC SEL is
floating. In this mode, OSC IN selects between the
1.6s and 100ms watchdog timeout periods. In either
case, immediately after a reset the timeout period 1.6s.
This gives the microprocessors time to reintialize the
system. If OSC IN is low, then the 100ms watchdog
period becomes effective after the first transition of WDI.
The software should be written such that the I/O port
driving WDI is left in its power-up reset state until the initialization routines are completed and the microprocessor
is able to toggle WDI at the minimum watchdog timeout
period of 70ms.
Watchdog Timer and Oscillator
The watchdog circuit monitors the activity of the microprocessor. If the microprocessor does not toggle the
Watchdog Input (WDI) within the selected timeout period,
a 50ms* RESET pulse is generated. Since many systems
cannot service the watchdog timer immediately after a
reset, the MAX691/MAX693/MAX695 has a longer timeout period after reset is issued. The normal timeout period
becomes effective following the first transition of WDI after
RESET has gone high. The watchdog timer is restarted
*200ms for MAX694
PRESCALER
WATCHDOG INPUT
VCC
Q6
2.7V
+
WATCHDOG TIMEOUT SELECT
HI IF WATCHDOG
INPUT IS FLOATING
RESET
COUNTER
+
10.24 kHz FROM INTERNAL OSCILLATOR
OR EXTERNALLY SET FREQUENCY FROM
OSC IN PIN
R
Q10/12
WATCHDOG
COUNTER
Q11
Q13
R
Q15
WATCHDOG
TIMEOUT
SELECTOR
LOGIC
1.0V
GOES HIGH AT THE
END OF WATCHDOG
TIMEOUT PERIOD
TRANSACTION
DETECTOR
FOR EACH TRANSITION
LOW LINE
(HI IF VCC < 4.65V)
S
R
RESET
FLIP FLOP
Q
Q
RESET RESET
S
Q
LONG/SHORT
FF
R
R
LOW
LINE
S
WATCHDOG
FAULT FF
Q
WATCHDOG OUTPUT
Figure 7. Watchdog Timer Block Diagram
www.maximintegrated.com
Maxim Integrated │ 11
MAX690–MAX695
Microprocessor Supervisory Circuits
EXTERNAL CLOCK
8
EXTERNAL OSCILLATOR
8
OSC SEL
OSC SEL
MAX691
MAX693
MAX695
0 TO 250kHz
7
MAX691
MAX693
MAX695
7
OSC IN
OSC IN
COSC
INTERNAL OSCILLATOR
1.6s WATCHDOG
N.C.
N.C.
8
7
INTERNAL OSCILLATOR
100ms WATCHDOG
N.C.
OSC SEL
MAX691
MAX693
MAX695
8
7
OSC IN
OSC SEL
MAX691
MAX693
MAX695
OSC IN
Figure 8. Oscillator Circuits
Table 1. MAX691/MAX693/MAX695 Reset Pulse Width and Watchdog Timeout Selections
WATCHDOG TIMEOUT PERIOD
OSC SEL
OSC IN
Low
External Clock Input
Low
External Capacitor
Floating
Low
Floating
Floating
RESET TIMEOUT PERIOD
NORMAL
IMMEDIATELY
AFTER REST
MAX691/MAX693
MAX695
1024 clks
4096 clks
512 clks
2048 clks
400ms/47pF x C
1.6s/47pF x C
200ms/47pF x C
800ms/47pF x C
100ms
1.6s
50ms
200ms
1.6s
1.6s
50ms
200ms
Note 1: The MAX690/MAX692/MAX694 watchdog timeout period is fixed at 1.6s nominal, the MAX690/692 reset pulse width is fixed
at 50ms nominal and the MAX694 is 200ms nominal.
Note 2: When the MAX691 OSC SEL pin is low, OSC IN can be driven by an external clock signal or an external capacitor can be
connected between OSC IN and GND. The nominal internal oscillator frequency is 6.55kHz. The nominal oscillator frequency
with capacitor is:
120,000
f OSC (Hz) =
C(pF)
Note 3: See Electrical Characteristics table for minimum and maximum timing values.
www.maximintegrated.com
Maxim Integrated │ 12
MAX690–MAX695
Microprocessor Supervisory Circuits
Application Hints
Adding Hysteresis
to the Power Fail Comparator
Other Uses of the Power-Fail Detector
In Figure 9, the power-fail detector is used to initiate a
system reset when VCC falls to 4.85V. Since the threshold of the power-fail detector is not as accurate as the
onboard reset-voltage detector, a trimpot must be used
to adjust the voltage detection threshold. Both the PFO
and RESET outputs have high sink current capability and
only 10µA of source current drive. This allows the two
outputs to be connected directly to each other in a wired
OR fashion.
The overvoltage detector circuit in Figure 10 resets the
microprocessor whenever the nominal 5V VCC is above
5.5V. The battery monitor circuit (Figure 11) shows the
status of the memory backup battery. If desired, the CE
OUT can be used to apply a test load to the battery. Since
CE OUT is forced high during the battery backup mode,
the test load will not be applied to the battery while it is in
use even if the microprocessor is not powered.
10kΩ
VCC
VCC
MAX690
MAX691
MAX692
MAX693
MAX694
MAX695
PFO
GND
Figure 9. Externally Adjustable VCC Reset Threshold
www.maximintegrated.com
The Watchdog feature can be enabled and disabled
under program control by driving WDI with a three-state
buffer (Figure 13). The drawback to this circuit is that a
software fault may be erroneously three-state the buffer,
thereby preventing the MAX690 from detecting that the
microprocessor is no longer working. In most cases a better method is to extend the watchdog period rather than
disabling the watchdog. See Figure 14. When the control
input is high, the OSC SEL pin is low and the watchdog
timeout is set by the external capacitor. A 0.01µF capacitor sets a watchdog timeout delay of 100s. When the
control input is low the OSC SEL pin is high, selecting
the internal oscillator. The 100ms or the 1.6s period is
chosen, depending on which diode in Figure 14 is used.
+5V
RESET
PFI
Alternate Watchdog Input Drive Circuits
+5V
29.4kΩ
2kΩ
Since the power fail comparator circuit is noninverting, hysteresis can be added by connecting a resistor
between the PFO output and the PFI input as shown in
Figure 12. When PFO is low, resistor R3 sinks current
from the summing junction at the PFI pin. When PFO is
high, the series combination of R3 and R4 source current
into the PFI summing junction.
TO µP
RESET
INPUT
35.7kΩ
2kΩ
10kΩ
RESET
PFI
MAX690
MAX691
MAX692
MAX693
MAX694
MAX695
PFO
TO µP
RESET
INPUT
N-CHANNEL
GND
Figure 10. Reset on Overvoltage or Undervoltage
Maxim Integrated │ 13
MAX690–MAX695
Microprocessor Supervisory Circuits
7V TO 15V
+5V
7805
VCC
+5V
PFO
R1
75kΩ
VBATT
10MΩ
PFI
10MΩ
RL
CE OUT
VCC
LOW BATTERY
SIGNAL TO
µP I/O PIN
PFO
MAX690
MAX691
MAX692
MAX693
MAX694
MAX695
GND
MAX690
MAX691
MAX692
MAX693
MAX694
MAX695
R4
10kΩ
PFI
R2
13kΩ
CE IN
LOW
APPLIES
LOAD
TO BATTERY
FROM µP
I/O PIN
GND
R3
300kΩ
TO P
VH = 9.125V
VL = 7.9V
HYSTERESIS = 1.23V
(
)
R1
(5V
-1.3V) R1
V = 1.3V (1 +
R2 1.3V (R3 + R4) )
VH = 1.3V 1 +R1 +R1
R2 R3
L
HYSTERESIS 5V x R1
R3
ASSUMING R4 < < R3
Figure 11. Backup VBattery Monitor with Optional Test Load
Figure 12. Adding Hysteresis to the Power-Fail Voltage
Comparator
+5V
+5V
VCC
WATCHDOG
STROBE
EN
WATCHDOG
DISABLE
WDI
MAX690
MAX691
MAX692
MAX693
MAX694
MAX695
GND
Figure 13. Disabling the Watchdog Under Program Control
www.maximintegrated.com
VCC
LOW = INTERNAL
WATCHDOG TIMEOUT
OSC SEL
MAX691
MAX693
HI = EXTERNAL
WATCHDOG
TIMEOUE
CONNECT FOR
100ms TIMEOUT
WHEN INTERNAL
TIMEOUT IS
SELECTED
OSC IN
GND
CONNECT FOR
1.6s INTERNAL
TIMEOUT
Figure 14. Selecting Internal or External Watchdog Timeout
Maxim Integrated │ 14
MAX690–MAX695
Microprocessor Supervisory Circuits
Table 2. Input and Output Status In Battery Backup Mode
VBATT, VOUT
VBATT is connected to VOUT via internal MOSFET.
RESET
Logic-low
RESET
Logic-high. The open circuit output voltage is equal to VOUT.
LOW LINE
Logic-low
BATT ON
Logic-high
WDI
WDI is internally disconnected from its internal pullup and does not source or sink current as long as its input
voltage is between GND and VOUT. The input voltage does not affect the source current.
WDO
Logic-high
PFI
The power-fail comparator is turned off and the power-fail input voltage has no effect on the power-fail output.
PFO
Logic-low
CE IN
CE IN is internally disconnected from its internal pullup and does not source or sink current as long as its input
voltage is between GND and VOUT. The input voltage does not affect the source current.
CE OUT
Logic-high
OSC IN
OSC IN is ignored.
OSC SEL
OSC SEL is ignored.
VCC
Approximately 12µA is drawn from the VBATT input when VCC is between VBATT +100mV and VBATT - 700mV.
The supply current is 1µA maximum when VCC is less than VBATT - 700mV.
www.maximintegrated.com
Maxim Integrated │ 15
MAX690–MAX695
Microprocessor Supervisory Circuits
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
PART
TEMP RANGE
PIN-PACKAGE
MAX690CPA
0°C to +70°C
8 Lead Plastic DIP
MAX693CPE
0°C to +70°C
16 Lead Plastic DIP
MAX690C/D
0°C to +70°C
Dice*
MAX693CWE
0°C to +70°C
16 Lead Wide SO
MAX690EPA
-40°C to +85°C
8 Lead Plastic DIP
MAX693EPE
-40°C to +85°C
16 Lead Plastic DIP
MAX690EJA
-40°C to +85°C
8 Lead CERDIP
MAX693EJE
-40°C to +85°C
16 Lead CERDIP
MAX690MJA
-55°C to +125°C
8 Lead CERDIP
MAX693EWE
-40°C to +85°C
16 Lead Wide SO
MAX691CPE
0°C to +70°C
16 Lead Plastic DIP
MAX693MJE
-55°C to +125°C
16 Lead CERDIP
MAX691CWE
0°C to +70°C
16 Lead Wide SO
MAX694C/D
0°C to +70°C
Dice
MAX691C/D
0°C to +70°C
Dice*
MAX694CPA
0°C to +70°C
8 Lead Plastic DIP
MAX691EPE
-40°C to +85°C
16 Lead Plastic DIP
MAX694EPA
-40°C to +85°C
8 Lead Plastic DIP
MAX691EWE
-40°C to +85°C
16 Lead Wide SO
MAX694EJA
-40°C to +85°C
8 Lead CERDIP
MAX691EJE
-40°C to +85°C
16 Lead CERDIP
MAX694MJA
-55°C to +125°C
8 Lead CERDIP
MAX691MJE
-55°C to +125°C
16 Lead CERDIP
MAX695C/D
0°C to +70°C
Dice
MAX692C/D
0°C to +70°C
Dice
MAX695CPE
0°C to +70°C
16 Lead Plastic DIP
MAX692CPA
0°C to +70°C
8 Lead Plastic DIP
MAX695CWE
0°C to +70°C
16 Lead Wide SO
MAX692EPA
-40°C to +85°C
8 Lead Plastic DIP
MAX695EPE
-40°C to +85°C
16 Lead Plastic DIP
MAX692EJA
-40°C to +85°C
8 Lead CERDIP
MAX695EJE
-40°C to +85°C
16 Lead CERDIP
MAX692MJA
-55°C to +125°C
8 Lead CERDIP
MAX695EWE
-40°C to +85°C
16 Lead Wide SO
MAX693C/D
0°C to +70°C
Dice
MAX695MJE
-55°C to +125°C
16 Lead CERDIP
*Contact factory for dice specifications.
Devices in PDIP and SO packages are available in both leaded and lead-free packaging. Specify lead free by adding the + symbol at
the end of the part number when ordering. Lead free not available for CERDIP package.
www.maximintegrated.com
Maxim Integrated │ 16
MAX690–MAX695
Microprocessor Supervisory Circuits
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
8 PDIP
P8-2
21-0043
—
8 CEDIP
J8-2
21-0045
—
16 PDIP
P16-1
21-0043
—
16 Wide SO
W16-1
21-0042
—
16 CERDIP
P16-1
21-0043
—
Chip Topography
VCC VOUT
VBATT
RESET
RESET
2
1
16
15
3
14
13
12
0.122”
(3.098 mm)
GND
BATT
ON
WDO
CE IN
CE OUT
4
5
6
LOW LINE
7
8
9
OSC
IN
OSC
SEL
PFI
10 11
PFO
WDI
0.086”
(2.184 mm)
www.maximintegrated.com
Maxim Integrated │ 17
MAX690–MAX695
Microprocessor Supervisory Circuits
Revision History
REVISION
NUMBER
REVISION
DATE
5
4/15
DESCRIPTION
Revised Benefits and Features section
PAGES
CHANGED
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2015 Maxim Integrated Products, Inc. │ 18
工商网监
湘ICP备2023018690号
